7135-20.00M [CONNOR-WINFIELD]
5.0V HCMOS Surface Mount Crystal Clock Oscillator; HCMOS 5.0V表面贴装晶体时钟振荡器型号: | 7135-20.00M |
厂家: | CONNOR-WINFIELD CORPORATION |
描述: | 5.0V HCMOS Surface Mount Crystal Clock Oscillator |
文件: | 总2页 (文件大小:82K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
5.0V HCMOS Surface Mount
Crystal Clock Oscillator
7115, 7125, 7135
XO
Features:
2111 Comprehensive Drive
1.8 to 50 MHz
Aurora, Illinois 60505
The Connor-Winfield models 7115,
5.0V Operation
7125, and 7135 are a 5 x 3.2mm, 5.0V
Phone: 630-851-4722
RoHS Compliant
HCMOS, Surface Mount, Fixed
Fax: 630- 851- 5040
Tri-State Enable / Disable Function
Frequency Crystal Oscillators (XO)
designed for use in all applictions
requiring precision clocks. The RoHS
compliant, surface mount package is
designed for high-density mounting
and is optimum for mass production.
www.conwin.com
Overall Frequency Tolerance:
7115 ± 25 ppm
US Headquarters:
630-851-4722
European Headquarters:
+353-61-472221
7125 ± 50 ppm
7135 ± 100 ppm
Temperature Range: 0 to 70°C
Ceramic Surface Mount Package
Tape and Reel Packaging
Absolute Maximum Ratings
Parameter
Minimum
-55
Nominal
Maximum
125
Units
°C
Vdc
Notes
Storage Temperature
Supply Voltage (Vcc)
-
-
-0.5
7.0
Operating Specifications
Parameter
Minimum
Nominal
Maximum
Units
MHz
ppm
Notes
Frequency Range (Fo)
1.8
-
50
Frequency Tolerance
1
7115
7125
7135
-25
-50
-
-
-
25
50
-100
100
Operating Temp Range
Supply Voltage (Vdd)
Supply Current (Icc)
0
4.5
-
-
5.0
-
70
5.5
45
°C
Vdc
mA
Input Characteristics
Parameter
Minimum
Nominal
Maximum
Units
Vdc
Vdc
nS
Notes
Enable Voltage - (Vih)
Disable Voltage - (Vil)
Enable Time
2.2
-
-
-
-
-
2
-
-
-
0.8
100
100
Disable Time
nS
HCMOS Output Characteristics
Parameter
Minimum
Nominal
Maximum
Units
Notes
Load
-
-
50
pF
High (Voh)
Voltage
4.50
-
-
-
-
Vdc
Low (Vol)
0.55
High (loh)
Current
-16
-
-
-
-
mA
Low (lol)
16
Duty Cycle at 50% of Vcc
Rise / Fall Time 10% to 90%
Start-Up Time
40
50
60
5
10
5
%
nS
mS
-
-
-
-
-
-
Jitter
pS RMS
Bulletin
Sm088
Page
1 of 2
Notes:
1. Inclusive of calibration @ 25°C , frequency vs temperature stability, supply voltage change, load change, shock and vibration, 10 years aging.
2. Oscillator output is enabled with no connection on pad 1
Revision
01
Date
20 June 2002
Specifications subject to change without notice. All dimensions in inches. © Copyright 1998 The Connor-Winfield Corporation
2111 Comprehensive Drive
Aurora, Illinois 60505
Phone: 630-851-4722
Fax: 630- 851- 5040
www.conwin.com
Package Characteristics
Hermetically sealed ceramic package and metal cover
Suggested Pad Layout
Package
Environmental Characteristics
Temperature Cycle
The specimen shall meet electrical characteristics after
tested 5 cycles of -55°C / 30 minutes and +125°C / 30 minutes
Hermetical
No bubbles appear in Flourinert (FC-43) at 125°C 5°C for 5 minutes
Solvent Resistance
Marking will withstand immersion in
Isopropyl Alcohol or Trichloroethylene
Bypass capacitor, C-by, should
be ceramic capacitor ≥ ±.1uf±
Soldering
General Conditions
260°C max x 10 sec max x 2 times max or
230°C max x 180 sec max x 1 time
Typical Operation Data
(Vapor phase reflow)
20 to 100 sec up to 215°C, 50 sec
Test Circuit
at 215°C, then down to room temperature per 1 to 5°C / sec
OSCILLOSCOPE
Mechanical Characteristics
PROBE
POWER
SUPPLY
Free Drop
Vibration
The specimen shall meet electrical characteristics after tested 3 times,
Free Drop testing on the hard wooden board from a height of 75 cm.
OSC
The specimen shall meet electrical characteristics after tested
by the following conditions: 10-55Hz 1.5mm Amplitude,
55-2000 Hz 20 G's, 2 hours for each plane
After applied Thermal Shock of 260°C
max x 10 sec max x 2 times, or 230°C max x 180 sec max,
the specimen shall meet electrical characteristics
FREQ
INPUT FOR E/D
COUNTER
Thermal Shock
Solderability
(EIAJ-RCX-0102.101 Condition 1a)
1) Flux: MIL-F-14256 (WW Rosin=25%, Isopropyl Alcohol = 75%)
2) Solder: QQ-S-571 (Sn = 63%, Pb = 37%)
OutputWaveform
3) Solder bath temperature: 235°C 5°C
4) Depth of immersion: Up to electrical terminal
5) Immersing time: Within 2 sec 0.5 sec into solder bath
After performing the above procedures, a newly soldered coverage shall be greater than 90%
Pad Connection
1: Enable / Disable
2: Ground
SYMMETRY
3: Output
4: Vcc
Dimensional Tolerance: ± ±.0ꢂ ꢀ±ꢁ.8mmꢃ
± ±..ꢁꢂ ꢀ±10ꢄmmꢃ
Tape and Reel Dimensions
Ordering Information
ꢄ11ꢁ
- 0.±.. MHz
CLOCK
SERIES
CENTER
FREQUENCY
Dimensional Tolerance: ±.02" (.508mm)
±.005"(.127mm)
Bulletin
Page
Sm088
2 of 2
Revision
Date
01
Meets EIA-481A and EIAJ-1..9B
0,... PCS/REEL
20 June 2002
Specifications subject to change without notice. All dimensions in inches. © Copyright 1998 The Connor-Winfield Corporation
相关型号:
©2020 ICPDF网 联系我们和版权申明