SCG2030-001.544M [CONNOR-WINFIELD]
Support Circuit, 1-Func, CMOS, MODULE-14;
| 型号： | SCG2030-001.544M |
| 厂家： | 
CONNOR-WINFIELD CORPORATION |
| 描述： | Support Circuit, 1-Func, CMOS, MODULE-14 ATM 异步传输模式 电信 电信集成电路 |
| 文件： | 总16页 (文件大小：1191K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
SCG2000i
Synchronous Clock
Generators
PLL
2111 Comprehensive Drive
Aurora, Illinois 60505
Phone: 630-851-4722
Fax: 630- 851- 5040
www.conwin.com
Application
Features
The Connor-Winfield SCG2000i provides
high precision phase lock loop frequency
translation for the telecommunication
applications that require a temperature
range of -40°C to 85°C.
• Industrial
Temperature
Range
• 3.3V High
Precision PLL
SCG2000i is well suited for use in line
cards, service termination cards and
similar functions to provide reliable
reference, phase locked, synchronization
and low phase gain for TDM, PDH, SONET
and SDH network equipment. The
SCG2000i provides a jitter filtered, wander
following output signal synchronized to a
superior Stratum or peer input reference
signal.
• Tri-State Capability
• Active Alarms
• Guaranteed Free
Run (20ppm for
19.44MHz output
and 30ppm for
125.0 MHz)
Bulletin
SG048
Page
1 of 16
• 1 Sec. Acquisition
Time
Revision
P02
Date
28 Oct 02
Issued By
MBATTS
General Description
with the 19.44 MHz model and 30 ppm accurate output with
the 125.0 MHz model. Additionally the Free Run mode may
be entered manually by asserting a high signal to the Free
Run Enable pin. The outputs, except the oscillator output,
may be put into the tri-state high impedance condition for
external testing purposes by asserting a high signal to the
Tri-State Enable pin.
The SCG2000i is 3.3 Volt components that typically
draw less than 100 mA. All models have an acquisition
time of approximately 1.0 second and can be used in
applications that require temperature rating of -40° to
85° C. All models have a 33Ω resistor in series with the
oscillator output. The SCG2000i maximum package
dimensions are .78” x .83” x .35” on a six layer FR4 board
with surface mount pins. Parts are assembled using high
temperature solder to withstand surface mount reflow
process.
The SCG2000i provides high precision phase lock loop
frequency translation for the telecommunication applications. The
SCG2000i generates a CMOS output from an intrinsically low
jitter, voltage controlled crystal oscillator. while providing a jitter
attenuated, internal reference that is connected to a Reference
Output pin.
SCG2000i is well suited for use in line cards, service
termination cards and similar functions to provide reliable
reference, phase locked, synchronization for TDM, PDH, SONET
and SDH network equipment . The SCG2000i provides a low
phase gain (<0.2dB), jitter filtered, wander following output signal
synchronized to a superior Stratum or peer input reference
signal.
The SCG2000i include the following features: Free Run, Tri-
state and alarm outputs for Loss-of-Reference, (LOR), Loss-of-
Lock, (LOL). During the LOR alarm, the SCG2000i will also enter
a Free Run state which will guarantee a 20 ppm accurate output
Functional Block Diagram
Figure 1
Tri-State Enable
(Pin 10)
LOL Alarm Output
(Pin 7)
ALARM
LOR Alarm Output
(Pin 6)
DETECTION
Free Run Enable
(Pin 5)
Reference Input
ANALOG
FILTER
FREE RUN
CONTROL
Oscillator Output
(Pin 9)
DIVIDER
DPFD
VCXO
(Pin 8)
Optional Oscillator Output
(Pin 1)
DIVIDER
Reference Output
(Pin 1)
(Not available on
models with optional
oscillator output)
Input Freq. Select A
(Pin 14)
Input Freq. Select B
(Pin 13)
Model Comparison Table
Table 1
Model
Max
Duty
Cycle
Input
Ref Freq
Reference Output
(Pin #1)
Oscillator Output
(Pin #9)
Notes
SCG2000 8-64 kHz
SCG2000i 8-16 kHz
SCG2010 19.44 MHz
SCG2020 19.44 MHz
SCG2030 8-64 kHz
SCG2050 8-64 kHz
SCG2070 19.44 MHz
40/60
45/55
40/60
40/60
45/55
40/60
40/60
= Input Ref Freq.
= Input Ref Freq.
8 kHz
1.544 MHz to 125.0 MHz
19.44 MHZ, 125.0 MHz
19.44 MHz
Basic Model
Industrial Temp. Range
19.44 MHz
77.76 MHz
= Input Ref Freq.
19.44 MHz
1.544 MHz to 125.0 MHz
77.76 MHz
Tight Duty Cycle
51.84 MHz, 77.76 MHz
51.84 MHz, 77.76 MHz
Ref Output = Osc Output
*Features which differentiate a model from the base model (SCG2000) are highlighted in boldface color and in the notes column.
Data Sheet #: SG048
Page 2 of 16
Rev: P02 Date: 10 / 28 / 02
© Copyright 2002 The Connor-Winfield Corp. All Rights Reserved Specifications subject to change without notice
Pin Description
Table 2
Pin #
Connection
Description
1
2
Reference Output
TCK
Output frequency is dependent on SCG model
JTAG pin that is used only by Connor-Winfield for programming. Do not connect
JTAG pin that is used only by Connor-Winfield for programming. Do not connect
Ground
3
TMS
4
Ground
5
Free Run Enable/TDI
Loss of Reference (LOR)
Loss of Lock (LOL)
Reference Input
Oscillator Output
Tri-State enable
Free Run enable pin. 1 = Free Run. Input is pulled to GND
Alarm indicator. 1 = The reference has been lost.
Alarm indicator. 1 = Phase lock has been lost
Input reference frequency
6
7
8
9
Output frequency is dependent on SCG model
10
Tri State control for all outputs except Oscillator Output. 1 = Hi-Z, 0 = normal.
Input is pulled to GND.
11
12
13
14
Vcc
3.3V Supply Voltage.
TDO
JTAG pin that is used only by Connor-Winfield for programming. Do not connect
Control pin B used to select input frequency. Input is pulled to GND.
Control pin A used to select input frequency. Input is pulled to GND.
Input Freq. Select B
Input Freq. Select A
Typical Application
Figure 2
BITS
System
Signal
Input Select
Line Card 1
Timing Card #1
S
A
B
CW's SCG
2000/4000
MUX
A
Clock out
RCV
Y
CW's STM/MSTM module
Y
MUX
B
S
Line Card #N
Timing Card #N
S
A
CW's SCG
2000/4000
Clock out
RCV
A
MUX
CW's STM/MSTM module
Y
Y
B
MUX
B
S
System Select
Data Sheet #: SG048
Page 3 of 16
Rev: P02 Date: 10 / 28 / 02
© Copyright 2002 The Connor-Winfield Corp. All Rights Reserved Specifications subject to change without notice
Absolute Maximum Rating
Table 3
Symbol
Vcc
Parameter
Minimum
-0.5
Nominal
Maximum
Units
Volts
Notes
Power Supply Voltage
Input Voltage
4
V1
-0.5
5.5
150
Volts
Ts
Storage Temperature
-65
deg. C
Specifications
Table 4
Parameter
Voltage
Specifications
3.3V 5ꢀ
Notes
1.0
Current
100 mA Typical
-40° to 85°C
Temperature Range
Input Jitter Tolerance
(Input Jitter Frequencies > 10 Hz)
≥31.25us Typical
Jitter Bandwidth
Acquisition Time
Capture/Pull-in Range
Output Duty Cycle
Output Rise and Fall Time
Output Load
<15 Hz (8 Hz Typical)
Approx 1.0 second
2.0
32 ppm Minimum
40/60 ꢀ Min/Max @ 50ꢀ Level
3 ns @ 20ꢀ to 80ꢀ output level
30 pF
Alarms
LOR, LOL Status on seperate outputs
Free Run Accuracy
20 ppm (19.44 MHz output)
30 ppm (125.0 MHz output)
Package
TDEV
Fr4 SM 0.78" x .83" x 0.35" (maximum)
60 ps Typical
MTIE
750 ps Typical
Reference Output/Oscillator Output Offset ≤ 8 ns
Static Offset
26 ns Maximum
28 ns Maximum
3.0
4.0
Dynamic Offset
Input And Output Characteristics
Table 5
Symbol
VIH
Parameter
Minimum
Nominal
Maximum
Units
V
Notes
High Level Input Voltage
2
0
5.5
0.8
10
VIL
Low Level Input Voltage
V
TIO
I/O to Output Valid
nS
pF
CO
Output Capacitance
10
VHO
VIO
High Level Output Voltage loH = -4mA
Low Level Output Voltage loL = 8mA
Input Reference Signal Pulse Width
2.4
30
Vcc Min.
Vcc Max.
0.4
TIR
nS
NOTES: 1.0: Requires external regulation
2.0: From a 20 ppm offset in reference frequency
3.0: Offset between Reference Input and Reference Output @ room temp.
4.0: Offset change between Reference Input and Reference Output over temperature range from room temperature
`
Data Sheet #: SG048
Page 4 of 16
Rev: P02 Date: 10 / 28 / 02
© Copyright 2002 The Connor-Winfield Corp. All Rights Reserved Specifications subject to change without notice
Output Jitter Specifications
Table 6
Jitter BW 10 Hz - 20 MHz
pS (RMS) m UI
SONET Jitter BW 12 KHz - 20 MHz
Frequency (MHz)
19.44
pS (RMS)
m UI
10 Typ.
10 Typ.
0.194 Typ.
1.250 Typ.
1 Max., 0.5 Typ.
1 Max., 0.5 Typ.
0.019 Max.
0.125 Max.
125.0
Output Programming
Alarm Status
Table 7
Table 8
Tristate Free Run Output
LOL Output LOR Output Alarm Output
0
1
0
0
X
1
Locked to reference selected (default)
Hi-Z Tristate condition
Free run
0
1
X
0
0
1
No alarm
Loss-of-Lock
Loss-of-Reference
Maximum Package Dimensions
Figure 3
Recommended Footprint Dimensions
Figure 4
0.800 (20.32mm)
0.640 (16.26mm)
0.080 (2.03mm)
0.050 TYP
(1.27mm)
0.100 TYP
(2.54mm)
0.050 TYP
(1.27mm)
0.650
(16.51mm)
Data Sheet #: SG048
Page 5 of 16
Rev: P02 Date: 10 / 28 / 02
© Copyright 2002 The Connor-Winfield Corp. All Rights Reserved Specifications subject to change without notice
Input Reference Selection
Table 9
Input Sel A
(Pin #14)
Input Sel B
(Pin #13)
Reference Frequency
(Pin #8)
0
1
0
0
8 kHz (default)
16 kHz (Not available w/ 125.0 MHz output)
Reference and Output Availability
Table 10
Input Reference
(Pin #8)
Oscillator Output
(Pin #9)
Reference Output
(Pin #1)
8 kHz
16 kHz
8 kHz
16 kHz
19.44 MHz
125.0 MHz
8 kHz
8 kHz
Data Sheet #: SG048
Page 6 of 16
Rev: P02 Date: 10 / 28 / 02
© Copyright 2002 The Connor-Winfield Corp. All Rights Reserved Specifications subject to change without notice
Alarm Timing Diagram
Figure 5
LOR
Output
Start-up
Region
4
LOL
Output
2
1
1
Phase
Detector
3
External
Reference
Internal
Reference
2
2
2
2
2
2
2
2
2
2
2
2
2
2
LOR
Output
LOL
Output
5
1
1
1
1
1
Phase
Detector
3
3
External
Reference
Internal
Reference
2
2
2
2
2
2
2
2
2
2
2
2
2
2
19.44 MHz &77.76 MHz
8 kHz Reference Input Units
Reference Input Units
< 1 µsec
< 31.25 µsec
31.25 µsec
1
1 µsec
2
3
4
5
> 1 µsec
> 31.25 µsec
LOR is active when LOL is active
125 µsec wide range
Minimum pulse width = 2 µsec
Minimum pulse width = 62.5 µsec
During Start-up, The LOL Alarm will pulse
during the first second of operation
Start-up Region
Data Sheet #: SG048
Page 7 of 16
Rev: P02 Date: 10 / 28 / 02
© Copyright 2002 The Connor-Winfield Corp. All Rights Reserved Specifications subject to change without notice
SCG2000 Jitter Attenuation
Figure 6
Jitter Attenuation vs. Input Frequency
0.0
-5.0
-10.0
-15.0
-20.0
-25.0
-30.0
-35.0
-40.0
-45.0
1
10
100
1000
INPUT Jitter frequency (Hz)
Typical System Test Setup
Figure 7
Data Sheet #: SG048
Page 8 of 16
Rev: P02 Date: 10 / 28 / 02
© Copyright 2002 The Connor-Winfield Corp. All Rights Reserved Specifications subject to change without notice
SCG2000i Typical TDEV
Figure 8
100.0E-12
10.0E-12
1.0E-3
10.0E-3
100.0E-3
1.0E+0
10.0E+0
Integration Time ( )
(seconds)
SCG2000i Typical MTIE
Figure 9
1.0E-9
100.0E-12
1.0E-3
10.0E-3
100.0E-3
1.0E+0
10.0E+0
100.0E+0
Observation Window (S)
(seconds)
Data Sheet #: SG048
Page 9 of 16
Rev: P02 Date: 10 / 28 / 02
© Copyright 2002 The Connor-Winfield Corp. All Rights Reserved Specifications subject to change without notice
SCG2000i Switch from Free Run to a new Reference
Figure 10
000.0E+0
-10.0E-6
-20.0E-6
-30.0E-6
-40.0E-6
-50.0E-6
-60.0E-6
0
1
2
3
4
5
6
7
8
Time (sec)
SCG2000i Switch from a Reference to Free Run
Figure 11
2.0E-6
1.0E-6
000.0E+0
-1.0E-6
-2.0E-6
-3.0E-6
-4.0E-6
-5.0E-6
-6.0E-6
-7.0E-6
-8.0E-6
0
1
2
3
4
5
6
7
8
9
10
11
Time (sec)
Data Sheet #: SG048
Page 10 of 16
Rev: P02 Date: 10 / 28 / 02
© Copyright 2002 The Connor-Winfield Corp. All Rights Reserved Specifications subject to change without notice
SCG2000i Step Response due to a -20ppm Freq. Step
Figure 12
200.0E+0
000.0E+0
-200.0E+0
-400.0E+0
-600.0E+0
-800.0E+0
-1.0E+3
-1.2E+3
-1.4E+3
-1.6E+3
-1.8E+3
4
4.2
4.4
4.6
4.8
5
5.2
5.4
5.6
5.8
6
Time (sec)
SCG2000i 1µs Phase Transient Response
Figure 13
1.2E-6
1.0E-6
800.0E-9
600.0E-9
400.0E-9
200.0E-9
000.0E+0
-200.0E-9
4
5
6
7
8
Time (sec)
Data Sheet #: SG048
Page 11 of 16
Rev: P02 Date: 10 / 28 / 02
© Copyright 2002 The Connor-Winfield Corp. All Rights Reserved Specifications subject to change without notice
Tape and Reel Dimensions
Figure 14
Data Sheet #: SG048
Page 12 of 16
Rev: P02 Date: 10 / 28 / 02
© Copyright 2002 The Connor-Winfield Corp. All Rights Reserved Specifications subject to change without notice
Solder Profile
Figure 15
250
200
150
100
50
Temp
(C˚)
0
1
2
3
4
5
6
7
8
Time(minutes)
Recommended Reflow Profile
Peak Temp:217C˚
MaxRiseSlope:1.5C˚/Sec
Time Above150C˚:100Sec
Ordering Information
SCG{XXXX}-{FFF.FFF}{M}
XXXX equals a specific model (2000i)
FFF.FFF equals the Oscillator Output frequency (001.544, 002.048, 016.384, 019.44, 020.48,
037.056, 044.736, 049.152, 051.84, 077.76, 125.00)
M equals MHZ and is added to all part numbers
Example: To order an SCG2000i with an Oscillator Output of 19.44 MHz,
Order part number SCG2000i-019.44M
Please contact Connor-Winfield for other frequencies that may be available.
Data Sheet #: SG048
Page 13 of 16
Rev: P02 Date: 10 / 28 / 02
© Copyright 2002 The Connor-Winfield Corp. All Rights Reserved Specifications subject to change without notice
Data Sheet #: SG048
Page 14 of 16
Rev: P02 Date: 10 / 28 / 02
© Copyright 2002 The Connor-Winfield Corp. All Rights Reserved Specifications subject to change without notice
Revision
P00
Revision Date
5/14/02
Note
Preliminary Informational Release
Corrected Temp Range in General Description
Added 125.0 MHz model
P01
5/28/02
P02
10/28/02
Data Sheet #: SG048
Page 15 of 16
Rev: P02 Date: 10 / 28 / 02
© Copyright 2002 The Connor-Winfield Corp. All Rights Reserved Specifications subject to change without notice
2111 Comprehensive Drive
Aurora, Illinois 60505
Phone: 630-851-4722
Fax: 630- 851- 5040
www.conwin.com
相关型号：
©2020 ICPDF网 联系我们和版权申明