概述
规格参数
数据手册CB20712604 概述
30 A, BARRIER STRIP TERMINAL BLOCK, 1 ROW, 1 DECK 端子和端子排
CB20712604 规格参数
| 生命周期： | Active | Reach Compliance Code： | unknown |
| ECCN代码： | EAR99 | HTS代码： | 8536.69.40.40 |
| 风险等级： | 5.61 | 其他特性： | SAFETY APPROVAL: UL 94V-0, THERMOPLASTIC |
| 紧固方法： | SCREW | 安装类型： | BOARD |
| 层数： | 1 | 行数： | 1 |
| 通路数： | 26 | 额定电流： | 30 A |
| 额定电压： | 300 V | 安全认证： | UL; CSA; CE; IEC |
| 端子和端子排类型： | BARRIER STRIP TERMINAL BLOCK | 线规： | 12 AWG |
CB20712604 数据手册
通过下载CB20712604数据手册来全面了解它。这个PDF文档包含了所有必要的细节，如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载MAGNUM
®
Series A2000, LP2000 & CB2000
Single Row Terminal Blocks
A20510807WR
SPECIFICATIONS
Rating: A2: 30A, 300V*
LP2: 30A, 150V*
CB2: 30A, 300V*
Center Spacing: .375” or 3/8” (9.52 mm)
Wire Range: #12-22 AWG CU
Screw Size: #6-32 zinc plated philslot
Torque Rating: 9 in-lb.
LP202110
Base: Standoffs standard for easy flux washing
Distance Between Barriers: .32” (8.1 mm)
Recommended PCB Hole Diameter: .076” (1.93 mm)
Operating Temperature: 105°C (221°F) max., -40°C (-40°F) min.
Molded Material: Black, UL Rated 94V0 Thermoplastic
Breakdown Voltage: 3400V (A2 & LP2); 4100V (CB2).
Agency Information: UL/CSA; IEC Compliance;
CE Certified
CB20210507
*30A Rating achieved with a #10 copper wire crimped to a ring terminal.;
20A Rating without ring terminal.
A2000 & LP2000 Series
.375
(9.53)
.15
(3.8)
dia.
.65
(16.5)
MOUNTING
ENDS
BARRIER &
MOUNTING
ENDS
BARRIER
ENDS
ONLY
C
ONLY
A
C
B
C
Poles Mount Ctrs.
Length
Pole Ctrs.
Length
Mount End
Barrier End
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
1.13
1.50
1.88
2.25
2.63
3.00
3.38
3.75
4.13
4.50
4.88
5.25
5.63
6.00
6.38
6.75
7.13
7.50
7.88
8.25
8.63
9.00
9.38
9.75
10.13
10.50
10.88
11.25
11.63
1.56
1.93
2.30
2.68
3.06
3.43
3.81
4.18
4.56
4.93
5.31
5.69
6.06
6.43
6.81
7.18
7.56
7.93
8.31
8.68
9.06
9.43
9.81
10.18
10.56
10.93
11.31
11.68
12.05
.38
.75
.81
1.18
1.56
1.93
2.31
2.68
3.06
3.43
3.81
4.18
4.56
4.93
5.31
5.68
6.06
6.43
6.81
7.18
7.56
7.93
8.31
8.68
9.06
9.43
9.81
10.18
10.55
10.93
11.31
11.68
12.05
.76 (19.3)
.565 (14.35)
on LP2000
1.13
1.50
1.88
2.25
2.63
3.00
3.38
3.75
4.13
4.50
4.88
5.25
5.63
6.00
6.38
6.75
7.13
7.50
7.88
8.25
8.63
9.00
9.38
9.75
10.13
10.50
10.88
11.25
11.63
.40
(10.2)
.02
(.5)
A Mount Centers
B Pole Centers
Mount End
Barrier End
CB2000 Series
.375
(9.53)
.19
(4.8)
dia.
.70
(17.8)
.32
C
(8.1)
Mount End
Barrier End
.60
(15.2)
* Dimensions in inches. To convert to millimeters, multiply by 25.4.
.02
(.5)
A Mount Centers
B Pole Centers
Mount End
Barrier End
6
Series A2000 & LP2000
Single Row Terminal Blocks
Part Numbering System
Series
Terminal Style
Base/End
Poles
Screw Options
Options
A 2
L P 2
A2 - standard barrier 01 - handwired
0
- flat base/molded
mount end
- flat base/mnt. end
- flat base/barrier end
- insulator base/mnt. end
- insulator base/
barrier end
- closed base/
mount end
- closed base/
02 to 32
Blank
-
std. screw
AB - angle mnt. options (pg 9)
A1 to A9 - .250” QC
LP2 - low profile
02 - printed circuit
03 - non feed-thru
04 - wire wrap tail
05 - extended handwired
06 - handwired
02 to 30 on mount 00 - screws shipped bulk
barrier
1
2
3
4
end base 03 - stainless steel
04 - brass nickel plated
07 - steel SEMS
B1 to B9 - .187” QC
DR - drilled right angle (pg 9)
JA, JB & JC - barrier jumpers
(not available
L1 to L6 marking options (pg 22)
07 - extended pin
08 - printed circuit
09 - .250 QC short
10 - .187 QC
14 - printed circuit
19 - .250 QC long
with hardware options)
09 - brass SEMS
nickel plated
(not available with
hardware options
CA - captive screw
03CA - stainless steel captive S1 - solder lug/flat
04CA - brass captive
07CA - SEMS captive
09CA - brass SEMS captive
07WR - steel SEMS wire ready
(not available on LP2)
MP, MP8 & MT mounting plates (pg 9)
5
6
9
OJ2
&
OJ4 - over barrier jumpers (not
available w/covers)
RC - retaining clips (pg 9)
R30 to R77 - right angle bends (pg 9)
SO - stand off insulators (pg 9)
molded mount end
- insulator base/
molded mount end
)
Base/End Note: 0, 6,
9 styles not available
with covers. 5 & 6
Styles only available
with 03 terminals.
Covers - (pg 23)
Terminal Styles
Inches (Millimeters)
.20
.55
(14.0)
(5.1)
.55
(14.0)
.031
(.79)
.062
(1.57)
.031
(.79)
.062
(1.57)
031
.79)
.110
(2.79)
01
02
03
04
Handwired
Printed Circuit
Non Feed-Thru
Wire Wrap Tail
.17
.82
(20.8)
.30
(7.6)
.66
(16.8)
(4.3)
.031
(.79)
.062
(1.57)
.031
(.79)
.11
(2.79)
.031
(.79)
.110
(2.79)
.031
(.79)
.062
(1.57 )
08
05
07
06
Printed Circuit
Extended Handwired
Extended Pin
Handwired
.33
(8.4)
.41
(10.4)
.72
(18.3)
.40
(10.2)
.42
(10.7)
.31
(7.9)
.031
(.79)
.062
(1.57)
.125
(3.2)
.031
(.79)
.250
(6.35)
.031
(.79)
.187
(4.75)
.031
(.79)
.250
(6.35)
09
10
.187 QC
19
14
.250 QC short
.250 QC long
Printed Circuit
7
MAGNUM
®
Series A2000 & LP2000
Single Row Terminal Blocks Continued
Screw Options
Standard
Zinc Plated Steel
03
04
Brass
Nickel Plated
07
07WR
Wire Ready
(A2 only)
09
Stainless Steel
Steel SEMS
Brass SEMS
Nickel Plated
Hardware Options (Bulk ordering part numbers are in parentheses.)
Inches (Millimeters)
Jumpers
Solder Lugs
Quick Connects
Blade Width A = .250” Blade Width B = .187”
.68 (17.3)
.33 (8.4)
.84 (21.2)
S1
(2S1)
A1 & B1
OJ2
OJ4
A2 & B2
A3 & B3
JA
(2A1 & 2B1)
(JA2-XX)
(2A2 & 2B2)
(2A3 & 2B3)
.33 (8.4)
JB
(JB2-XX)
A5 & B5
(2A5 & 2B5)
A4 & B4
(2A4 & 2B4)
A6 & B6
(2A6 & 2B6)
.33 (8.4)
JC
(JC2-XX)
A9 & B9
(2A9 & 2B9)
A8 & B8
(2A8 & 2B8)
A7 & B7
(2A7 & 2B7)
Base/End Options
B
B
B
B
.180 (4.57)
.150 dia. (3.8)
mounting holes (2)
.218 (5.54)
.40
(10.2)
.40
10.2)
.095
(2.4)
SECTION A–A
SECTION B–B
0, 6 & 9
Molded Mount End
1, 3 & 5
Mount End
8
Series A2000 & LP2000
Single Row Terminal Blocks Continued
Mounting Options
Right Angle Bends (A2, LP2 only)
Right angle terminals are offered on the A2000
& LP2000 Series.
07 Terminal Bend Configurations
Configurations are defined in these dimensions: X = pin extension beyond the
block base; Z = length from block base to centerline of the terminal tip.
Standard bends consist of the X and Z dimensions shown in the chart.
Specify by adding the selected Bend Option Code to the terminal part no.
Z
04 Terminal Bend Configurations
.82
X
Z
Bend
Option
Code
Available
w/insulator
base
.55
X
X
Z
(minimum)
Bend
Option
Code
Available
w/insulator
base
R30
R35
R36
R42
R46
R50
R53
R66
R69
R75
R77
-.04
.01
.02
.08
.12
.16
.19
.32
.35
.41
.43
.55
.50
.49
.43
.39
.35
.32
.19
.16
.10
.08
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
No
X
Z
(minimum)
R30
R35
R36
R39
R42
R46
R48
R50
-.04
.01
.02
.05
.08
.12
.14
.16
.28
.23
.22
.19
.16
.12
.10
.08
No
No
No
No
No
No
No
No
Dimensions in inches. To convert to millimeters, multiply by 25.4.
Angle Brackets (A2, LP2 only)
Drilled Right Angle (A2, LP2 only)
.24
.375
.25
.04
.45
.32
.144 HOLE
w/.312 C' BORE
.15
Option DR
Option AB
Counterbored holes across mount ends of
block enable fastening with two screws at
right angles to normal mount position.
Angle brackets enable block to be fastened
at right angles to normal mount position.
Bulk part no. 2AB.
Standoffs
Retaining Clip
Mounting Plates
MOUNTING
PLATE
MP
MP8
MT
.300
RETAINING CLIP
STANDOFF
Option SO
Options MP, MP8 & MT
Option RC
Standoff mounts are tubes molded to the
mounting positions. Available with insulator
bases only.
MP Metal inserts with .150” dia. hole accept
#6 screw. MP8 Metal inserts with .187” dia.
hole accept #8-32 screw. MT Metal inserts
with tapped hole accept #6-32 screw.
Use on standoff tubes. Fit panels up to .125”
thick. Two clips for every five positions.
Supplied unassembled. Bulk Part No. H541.
9
MAGNUM
®
Series CB2000
Single Row Terminal Blocks
Part Numbering System
Series
Terminal Style
Base/End
Poles
Screws
Options
C B 2
CB2 - closed back 01 - handwired
02 - printed circuit
1
2
- mount end
- barrier end
02 to 32
03 - stainless steel
AB - angle mounting brackets (pg 11)
A7 to A9 - .250” QC
02 to 30 on mount
04 - brass nickel plated
03 - non feed-thru
end base 07 - steel SEMS
B7 to B9 - .187” QC
07 - extended pin
14 - printed circuit
22 - dual tail printed circuit
standard
09 - brass SEMS
nickel plated
EB - exit back terminals
EF - exit front terminals
JA, JB & JC - barrier jumpers
CA - captive screw
07CA - SEMS captive
L1 to L6 marking options (pg 22)
LT1 to LT6 marking options (pg 22)
OJ2
&
OJ4 - over barrier jumpers
MT8 mtg. plates (pg 11)
MP, MP8, MT
&
S1 - solder lug/flat
Covers - (pg.23)
Terminal Styles
Inches (Millimeters)
.19
(4.9)
.81
(4.6)
.125
(3.18)
.045
(1.14)
.03
(.79)
.19
.40
.70
(4.8 )
(10.2)
(17.8)
.0
(.7
.40
(10.2)
.0
(.
.045
(1.14)
.045
(1.14)
.18
(4.6)
.18
(4.6)
.43
(10.9)
.0
(.7
.0
(.
.120
(3.05)
.062
(1.57)
.18
.18
(4.6)
(4.6)
01
02
03
14
Printed Circuit
22
Dual Tail
Printred Circuit
07
Extended Pin
Handwired
Printed Circuit
Non Feed-Thru
Available on Mount
End (1) only.
Screw Options
03
04
Brass
Nickel Plated
07
09
Stainless Steel
Steel SEMS
Zinc Plated
Brass SEMS
Nickel Plated
* NOTE: Wire ready screws standard on all terminal styles.
CB2 Terminal Exit Options
Inches (Millimeters)
Y
.255
(6.48)
.18
(4.6)
.18
(4.6)
X
X
Exit Rear (std.)
EF Exit Front
EB Exit Back
10
Series CB2000
Single Row Terminal Blocks
Hardware Options (Bulk ordering part numbers are in parentheses.)
Inches (Millimeters)
Jumpers
Solder Lugs
Quick Connects
Blade Width A = .250”. Blade Width B = .187”.
.68 (17.3)
.33 (8.4)
.84 (21.2)
OJ2
OJ4
JA
A7 & B7
(2A7 & 2B7)
A8 & B8
(2A8 & 2B8)
S1
(2S1)
A9 & B9
(2A9 & 2B9)
(JA2-XX)
.33 (8.4)
JB
(JB2-XX)
.33 (8.4)
JC
(JC2-XX)
Mounting Options
Inches (Millimeters)
Right Angle Mounting Bracket
.71
(18.0)
Snap-in Angle Bracket
A
Chassis
or PCB
End Positions
usable
#6 or #8
mounting
screw & nut
(Customer
supplied.)
.79
(20.1)
.45
(11.4)
1.02
(25.8)
Exit Back (EB)
Terminals
.24
(6.1)
A
.42
(10.7)
Angle
Bracket
Option AB
Mounts blocks on PC boards at a right angle.
• Protects solder joints.
• Recommended for all EB (Exit Back) PCB terminal blocks.
• Bracket snaps securely on block (no hardware required).
• Minimum strip length (end positions are usable).
• Mount with #6-32 or #8-32 screws (not supplied).
Mounting Plates
Options MP, MP8, MT & MT8
MP
MP8
MP Metal inserts with .150” dia. hole accept #6 screw.
MP8 Metal inserts with .187” dia. hole accept #8-32 screw.
MT Metal inserts with tapped hole accept #6-32 screw.
MT8 Metal inserts with tapped hole accept #8-32 screw.
MT
MT8
MOUNTING
PLATE
11
CB20712604 相关器件
| 型号 | 制造商 | 描述 | 价格 | 文档 |
| CB20712604EB | COOPER | 30 A, BARRIER STRIP TERMINAL BLOCK, 1 ROW, 1 DECK | 获取价格 |
|
| CB20712607CA | COOPER | Barrier Strip Terminal Block, 30A, 1 Row(s), 1 Deck(s) | 获取价格 |
|
| CB20712607CAEB | COOPER | 30 A, BARRIER STRIP TERMINAL BLOCK, 1 ROW, 1 DECK | 获取价格 |
|
| CB20712609 | COOPER | 30 A, BARRIER STRIP TERMINAL BLOCK, 1 ROW, 1 DECK | 获取价格 |
|
| CB207126CA | COOPER | 30 A, BARRIER STRIP TERMINAL BLOCK, 1 ROW, 1 DECK | 获取价格 |
|
| CB207126CAEB | COOPER | 30 A, BARRIER STRIP TERMINAL BLOCK, 1 ROW, 1 DECK | 获取价格 |
|
| CB20712703 | COOPER | 30 A, BARRIER STRIP TERMINAL BLOCK, 1 ROW, 1 DECK | 获取价格 |
|
| CB20712703EB | COOPER | 30 A, BARRIER STRIP TERMINAL BLOCK, 1 ROW, 1 DECK | 获取价格 |
|
| CB20712704 | COOPER | Barrier Strip Terminal Block, 30A, 1 Row(s), 1 Deck(s) | 获取价格 |
|
| CB20712707 | COOPER | 30 A, BARRIER STRIP TERMINAL BLOCK, 1 ROW, 1 DECK | 获取价格 |
|
CB20712604 相关文章
HARTING(浩亭)圆形连接器产品选型手册
- 2024-10-31
- 6
HYCON(宏康科技)产品选型手册
- 2024-10-31
- 6
GREEGOO整流二极管和晶闸管产品选型手册
- 2024-10-31
- 7
西门子豪掷106亿美元，战略收购工程软件巨头Altair
- 2024-10-31
- 8
