KHNA30F [COSEL]
For DIN (35mm) rail products;
| 型号： | KHNA30F |
| 厂家： | 
COSEL CO., LTD. |
| 描述： | For DIN (35mm) rail products |
| 文件： | 总20页 (文件大小：3498K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
AC-DC Power Supplies DIN Rail Type
Power
Safety
Approvals
EMI
OCP
OVP
World wide
Inrush
current
limiting
Remote
ON/OFF
Factor
Correction
KH-series
Feature
For DIN (35mm) rail products
CE marking
Low Voltage Directive
Wide operating ambient temperature range
RoHS Directive
I/O terminal has 2 types, Euro Style and Barrier Blocks Style
Built in overcurrent protection, overvoltage protection circuits
EMI
-KHEA30F/60F/90F, KHNA30F/60F/90F
Low power consumption at no load
Complies with FCC-B, CISPR22-B, EN55011-B, EN55022-B,
VCCI-B
Complies with SEMI F-47 (Derating is required)
EMS Compliance : EN61204-3, EN61000-6-2
-KHEA120F/240F/480F, KHNA120F/240F/480F
Built in remote ON/OFF
Built in signal output for confirming output voltage
Complies with SEMI F-47
EN61000-4-2
EN61000-4-3
EN61000-4-4
EN61000-4-5
EN61000-4-6
EN61000-4-8
EN61000-4-11
Safety agency approvals
UL60950-1, UL508, C-UL (CSA60950-1), EN60950-1,
ANSI/ISA12.12.01, ATEX
Complies with DEN-AN
5-year warranty (refer to Instruction Manual)
June 29, 2020
KH-1
Ordering information
AC-DC Power Supplies DIN Rail Type
KHO A
30
F -OO -O
KHEA/KHNA30F
1
2
3
4
5
6
1
Series name
Example recommended EMI/EMC filter
NAC-04-472-D
R
KHE
：Euro style I/O terminals
KHN：
Barrier blocks style
I/O terminals
2
3
4
5
6
Single output
Output wattage
Universal input
Output voltage
Option
UL508
High voltage pulse noise type : NAP series
Low leakage current type : NAM series
C : with Coating
*
A higher current rating EMI/EMC filter
may be recommended in view of the
other devices that could be connected
in parallel with the power supply.
*Make sure necessary tests will be carried out on your end equipment with the power supply installed in accordance with any required EMC/EMI regulations.
MODEL
MAX OUTPUT WATTAGE[W]
DC OUTPUT
KHEA/KHNA30F-5
25
5V 5A
KHEA/KHNA30F-12
27.6
12V 2.3A
KHEA/KHNA30F-24
31.2
24V 1.3A
SPECIFICATIONS
MODEL
KHEA/KHNA30F-5
KHEA/KHNA30F-12
KHEA/KHNA30F-24
*11
VOLTAGE[V]
AC85 - 264 1
f
(Refer to
“Derating”) or DC88 - 370
ACIN 115V 0.45typ
ACIN 230V 0.30typ
0.50typ
0.30typ
0.55typ
0.35typ
CURRENT[A]
FREQUENCY[Hz]
50 / 60 (45 - 440) or DC
INPUT
ACIN 115V 84.0typ
ACIN 230V 85.5typ
87.0typ
88.5typ
88.5typ
89.5typ
EFFICIENCY[%]
ACIN 115V 18typ (Io=100%
）
(at cold start Ta=25
C
C
)
)
INRUSH CURRENT[A]
*
1
ACIN 230V 35typ (Io=100%
）
(at cold start Ta=25
LEAKAGE CURRENT[mA]
VOLTAGE[V]
0.45 / 0.75max (ACIN 100V / 240V 60Hz, Io=100%, According to IEC60950-1 and DEN-AN)
5
12
24
CURRENT[A]
5.0
2.3
1.3
PEAK CURRENT[A]
LINE REGULATION[mV]
LOAD REGULATION[mV]
-
-
-
*
*
2
2
20max
80max
48max
100max
150max
300max
300max
180max
360max
360max
120max
150max
48max
96max
150max
150max
300max
300max
180max
360max
360max
240max
290max
96max
0 to +70C 150max
*
3
RIPPLE[mVp-p]
-20 - 0C
300max
*
*
4
4
*
4
4
*
*
4
4
Io=0 - 30% 300max
0 to +70C 180max
OUTPUT
*
3
RIPPLE NOISE[mVp-p]
-20 - 0C
360max
*
Io=0 - 30% 360max
0 to +70C 50max
-20 to +70C 60max
TEMPERATURE REGULATION[mV]
*
5
20max
DRIFT[mV]
START-UP TIME[ms]
HOLD-UP TIME[ms]
200typ (ACIN 115V, Io=100%)
20typ (ACIN 115V, Io=100%)
4.50 to 5.50
OUTPUT VOLTAGE ADJUSTMENT RANGE[V]
OUTPUT VOLTAGE SETTING[V]
OVERCURRENT PROTECTION
10.80 to 13.20
12.00 to 12.48
22.50 to 28.50
24.00 to 24.96
5.00 to 5.15
*
10
Works over 105% of rating and recovers automatically
13.80 to 16.80
PROTECTION
CIRCUIT AND OVERVOLTAGE PROTECTION[V] 6.30 to 7.60
30.00 to 36.00
OTHERS
DC_OK LAMP
LED (Green)
INPUT-OUTPUT
INPUT-PE
OUTPUT-PE
AC3,000V 1minute, Cutoff current = 10mA, DC500V 50M
AC2,000V 1minute, Cutoff current = 10mA, DC500V 50M
W
W
min
min
min
（
（
At Room Temperature
At Room Temperature
）
）
ISOLATION
AC500V 1minute, Cutoff current = 100mA, DC500V 50M
W
（
At Room Temperature
）
OPERATING TEMP.,HUMID.AND ALTITUDE
STORAGE TEMP.,HUMID.AND ALTITUDE
-20 to +70
-30 to +85
C
C
, 20 - 90%RH (Non condensing), Type tested for -40
C
start-up (Refer to Derating”)
“
, 20 - 90%RH (Non condensing)
ENVIRONMENT
2
*
8
VIBRATION
IMPACT
10 - 55Hz, 19.6m/s (2G), 3minutes period, 60 minutes along Z axis (Non operating, mounted on DIN Rail)
2
196.1m/s (20G), 11ms, once each X, Y and Z axis (Packing state)
*
AC input UL60950-1, C-UL (CSA60950-1), EN60950-1, UL508 (NEC Class2 per UL1310), ANSI/ISA12.12.01, ATEX, Complies with DEN-AN
DC input UL60950-1, C-UL (CSA60950-1), EN60950-1
AGENCY APPROVALS
SAFETY AND
NOISE
REGULATIONS
CONDUCTED NOISE
HARMONIC ATTENUATOR
CASE SIZE
Complies with FCC-B, VCCI-B, CISPR22-B, EN55011-B, EN55022-B
*
6
（
*9
Complies with IEC61000-3-2 (Class A)
Not built-in to active filter)
*
7
22.5
X75X90mm (WXHXD) [0.89X2.95X3.54 inches]
OTHERS
WEIGHT
165g max
COOLING METHOD
Convection
*
1
The value is primary surge. The current of input surge to a built-in EMI/EMC Filter(0.2ms or less)is
excluded.
*
*
*
6
7
8
Please contact us about another class.
Case size contains neither the umbo.
Only as standard mounting orientation (A). Refer to the “Assembling and Installation Method”.
If install other than standard mounting orientation (A), please fix the power supply for withstand the
vibration and impact.
When two or more units are operating it may not comply with the IEC61000-3-2.
*
*
2
3
Please contact us about dynamic load and input response.
T
his is the value that measured on measuring board with capacitor of 22
mF and 0.1mF at 150mm from
output terminal.
Measured by 20MHz oscilloscope or Ripple-Noise meter (Equivalent to KEISOKU-GIKEN: RM103).
Please refer to the instruction manual 1.7.
Ripple and ripple noise spec is change at Io=0 to 30% by burst operation.
*
*
9
10 If the overcurrent protection circuit operates continuously, the output voltage shut down. Refer to
the instruction manual 1.3.
*
*
4
5
In case of operating under 0
30% load factor.
Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25
input voltage held constant at the rated input/output.
C
ambient temperature, the value is two times of specification at 0 to
*
11 Under low DC input voltage below DC110V, the temperature derating -1
derating -1%/V are required.
C/V or the output power
C
, with the
*
*
To meet the specifications. Do not operate over-loaded condition.
A sound may occur from power supply at light or peak loading.
June 29, 2020
KH-2
KH series
Block diagram
FUSE
500VAC/400VDC
3.15A
INRUSH
CURRENT
LIMIT
RECTIFIER
AND
FILTER
AC IN 85～264V
DCIN 88～370V
NOISE
FILTER
PE
TRANSFORMER
RECTIFIER
AND
CONTROL
INVERTER
DC OUT
FILTER
CURRENT
SENSING
Photocoupler
Photocoupler
CONTROL
OVER VOLTAGE
PROTECTION
External view
<KHEA30F(Euro Style I/O Terminals)>
<KHNA30F(Barrier Blocks Style I/O Terminals)>
4.9
6.4
90
[3.54]
6.6
9.3
[0.37] 5-M3.5
90
[3.54]
[0.19]
[0.25]
[0.26]
TB2
TB2
Output terminal(+)
Output terminal(
LED(DC_OK)
Output terminal(+)
-
)
Output terminal(
-)
LED(DC_OK)
Output voltage
adjustable potentiometer
Output voltage
adjustable potentiometer
10.9
[0.43]
10.9
[0.43]
PE
AC(L)
AC(L)
AC(N)
AC(N)
TB1
PE
TB1
4.9
6.4
94.5
[3.72]
6.6
[0.26]
9.3
[0.37]
10max
[0.39]
94.5
[3.72]
[0.19]
[0.25]
Name plate
Name plate
11.25
[0.44]
22.5
[0.89]
22.5
[0.89]
¶ Tolerance : 1 [ 0.04]
¶ Weight : 165g max
¶ PCB Material/thickness : FR-4 / 1.6mm [0.06]
¶ Chassis-Case material : PBT
¶ Tolerance : 1 [ 0.04]
¶ Weight : 165g max
¶ PCB Material/thickness : FR-4 / 1.6mm [0.06]
¶ Chassis-Case material : PBT
¶ Din rail attachment material : PC/ABS
¶ Dimensions in mm, [ ] = inches
¶ Screw tightening torque : 1N-m max
¶ Din rail attachment material : PC/ABS
¶ Dimensions in mm, [ ] = inches
¶ Screw tightening torque : 1.1N-m max
June 29, 2020
KH-3
Ordering information
AC-DC Power Supplies DIN Rail Type
KHO A
60
F -OO -O
KHEA/KHNA60F
1
2
3
4
5
6
1
Series name
Example recommended EMI/EMC filter
NAC-04-472-D
R
KHE
：Euro style I/O terminals
KHN：
Barrier blocks style
I/O terminals
2
3
4
5
6
Single output
Output wattage
Universal input
Output voltage
Option
UL508
High voltage pulse noise type : NAP series
Low leakage current type : NAM series
C : with Coating
*
A higher current rating EMI/EMC filter
may be recommended in view of the
other devices that could be connected
in parallel with the power supply.
*Make sure necessary tests will be carried out on your end equipment with the power supply installed in accordance with any required EMC/EMI regulations.
MODEL
KHEA/KHNA60F-12
KHEA/KHNA60F-24
MAX OUTPUT WATTAGE[W]
DC OUTPUT
54
12V 4.5A
60
24V 2.5A
SPECIFICATIONS
MODEL
KHEA/KHNA60F-12
KHEA/KHNA60F-24
*11
VOLTAGE[V]
AC85 - 264 1f(Refer to “Derating”) or DC88 - 370
ACIN 115V 1.00typ
ACIN 230V 0.60typ
1.10typ
0.70typ
CURRENT[A]
FREQUENCY[Hz]
50 / 60 (45 - 440) or DC
INPUT
ACIN 115V 87.0typ
ACIN 230V 88.0typ
89.0typ
91.0typ
EFFICIENCY[%]
ACIN 115V 18typ (Io=100%
）
(at cold start Ta=25
C
C
)
)
INRUSH CURRENT[A]
*
1
ACIN 230V 35typ (Io=100%
）
(at cold start Ta=25
LEAKAGE CURRENT[mA]
VOLTAGE[V]
0.45 / 0.75max (ACIN 100V / 240V 60Hz, Io=100%, According to IEC60950-1 and DEN-AN)
12
24
CURRENT[A]
4.5
2.5
PEAK CURRENT[A]
LINE REGULATION[mV]
LOAD REGULATION[mV]
-
-
*
*
2
2
48max
100max
96max
150max
200max
300max
300max
260max
360max
360max
240max
290max
96max
0 to +70C 200max
*
3
RIPPLE[mVp-p]
-20 - 0C
300max
*
*
4
4
*
*
4
4
Io=0 - 30% 300max
0 to +70C 260max
OUTPUT
*
3
RIPPLE NOISE[mVp-p]
-20 - 0C
360max
Io=0 - 30% 360max
0 to +70C 120max
-20 to +70C 150max
TEMPERATURE REGULATION[mV]
*
5
48max
DRIFT[mV]
START-UP TIME[ms]
HOLD-UP TIME[ms]
200typ (ACIN 115V, Io=100%)
20typ (ACIN 115V, Io=100%)
10.80 to 13.20
12.00 to 12.48
Works over 105% of rating and recovers automatically
OUTPUT VOLTAGE ADJUSTMENT RANGE[V]
OUTPUT VOLTAGE SETTING[V]
OVERCURRENT PROTECTION
22.50 to 28.50
24.00 to 24.96
10
*
PROTECTION
CIRCUIT AND OVERVOLTAGE PROTECTION[V] 13.80 to 16.80
30.00 to 36.00
OTHERS
DC_OK LAMP
LED (Green)
INPUT-OUTPUT
INPUT-PE
OUTPUT-PE
AC3,000V 1minute, Cutoff current = 10mA, DC500V 50M
AC2,000V 1minute, Cutoff current = 10mA, DC500V 50M
W
W
min
min
min
（
At Room Temperature
）
）
ISOLATION
（At Room Temperature
AC500V 1minute, Cutoff current = 100mA, DC500V 50M
W
（At Room Temperature
）
OPERATING TEMP.,HUMID.AND ALTITUDE
STORAGE TEMP.,HUMID.AND ALTITUDE
-20 to +70
C
, 20 - 90%RH (Non condensing) , Type tested for -40
C
start-up (Refer to “Derating”)
-30 to +85
C
, 20 - 90%RH (Non condensing)
ENVIRONMENT
2
*
8
VIBRATION
IMPACT
10 - 55Hz, 19.6m/s (2G), 3minutes period, 60 minutes along Z axis (Non operating, mounted on DIN Rail)
2
196.1m/s (20G), 11ms, once each X, Y and Z axis (Packing state)
*
AC input UL60950-1, C-UL (CSA60950-1), EN60950-1, UL508 (NEC Class2 per UL1310), ANSI/ISA12.12.01, ATEX, Complies with DEN-AN
DC input UL60950-1, C-UL (CSA60950-1), EN60950-1
AGENCY APPROVALS
SAFETY AND
NOISE
REGULATIONS
CONDUCTED NOISE
HARMONIC ATTENUATOR
CASE SIZE
Complies with FCC-B, VCCI-B, CISPR22-B, EN55011-B, EN55022-B
*
6
*9
Complies with IEC61000-3-2
（
Class A) Not built-in to active filter)
（
*
7
32
X
90X
90mm (W
X
HX
D) [1.26 3.54X3.54 inches]
X
OTHERS
WEIGHT
270g max
COOLING METHOD
Convection
*
1
The value is primary surge. The current of input surge to a built-in EMI/EMC Filter(0.2ms or less)is
excluded.
*
*
*
6
7
8
Please contact us about another class.
Case size contains neither the umbo.
Only as standard mounting orientation (A). Refer to the “Assembling and Installation Method”.
If install other than standard mounting orientation (A), please fix the power supply for withstand the
vibration and impact.
When two or more units are operating it may not comply with the IEC61000-3-2.
*
*
2
3
Please contact us about dynamic load and input response.
T
his is the value that measured on measuring board with capacitor of 22
mF and 0.1mF at 150mm from
output terminal.
Measured by 20MHz oscilloscope or Ripple-Noise meter (Equivalent to KEISOKU-GIKEN: RM103).
Please refer to the instruction manual 1.7.
Ripple and ripple noise spec is change at Io=0 to 30% by burst operation.
*
*
9
10 If the overcurrent protection circuit operates continuously, the output voltage shut down. Refer to
the instruction manual 1.3.
*
*
4
5
In case of operating under 0
30% load factor.
Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25
input voltage held constant at the rated input/output.
C
ambient temperature, the value is two times of specification at 0 to
*
11 Under low DC input voltage below DC110V, the temperature derating -1
derating -1%/V are required.
C/V or the output power
C
, with the
*
*
To meet the specifications. Do not operate over-loaded condition.
A sound may occur from power supply at light or peak loading.
June 29, 2020
KH-4
KH series
Block diagram
FUSE
500VAC/400VDC
3.15A
INRUSH
CURRENT
LIMIT
RECTIFIER
AND
FILTER
AC IN 85～264V
DCIN 88～370V
NOISE
FILTER
PE
TRANSFORMER
RECTIFIER
AND
CONTROL
INVERTER
DC OUT
FILTER
CURRENT
SENSING
Photocoupler
Photocoupler
CONTROL
OVER VOLTAGE
PROTECTION
External view
<KHEA60F(Euro Style I/O Terminals)>
<KHNA60F(Barrier Blocks Style I/O Terminals)>
6.5
[0.25]
6.4
[0.25]
90
[3.54]
6.7
[0.26]
9.3
[0.37]
90
[3.54]
6-M3.5
TB2
TB2
Output terminal(+)
Output terminal(
LED(DC_OK)
Output terminal(+)
Output terminal(
LED(DC_OK)
-)
-
)
Output voltage
Output voltage
adjustable potentiometer
adjustable potentiometer
AC(L)
AC(N)
PE
AC(L)
AC(N)
PE
TB1
TB1
9.3
6.5
[0.26]
9.5
94.5
[3.72]
6.7
[0.26]
94.5
[3.72]
[0.37]
[0.37]
11.2
[0.44]
11.2
[0.44]
Name plate
Name plate
32
[1.26]
32
[1.26]
¶ Tolerance : 1 [ 0.04]
¶ Weight : 270g max
¶ PCB Material/thickness : FR-4 / 1.6mm [0.06]
¶ Chassis-Case material : PBT
¶ Tolerance : 1 [ 0.04]
¶ Weight : 270g max
¶ PCB Material/thickness : FR-4 / 1.6mm [0.06]
¶ Chassis-Case material : PBT
¶ Din rail attachment material : PC/ABS
¶ Dimensions in mm, [ ] = inches
¶ Screw tightening torque : 1N-m max
¶ Din rail attachment material : PC/ABS
¶ Dimensions in mm, [ ] = inches
¶ Screw tightening torque : 1.1N-m max
June 29, 2020
KH-5
Ordering information
AC-DC Power Supplies DIN Rail Type
KHO A
90
F -OO -O
KHEA/KHNA90F
1
2
3
4
5
6
1
Series name
Example recommended EMI/EMC filter
NAC-04-472-D
R
KHE
：Euro style I/O terminals
KHN：
Barrier blocks style
I/O terminals
2
3
4
5
6
Single output
Output wattage
Universal input
Output voltage
Option
C : with Coating
E : NEC Class2 (24V)
UL508
High voltage pulse noise type : NAP series
Low leakage current type : NAM series
*
A higher current rating EMI/EMC filter
may be recommended in view of the
other devices that could be connected
in parallel with the power supply.
*Make sure necessary tests will be carried out on your end equipment with the power supply installed in accordance with any required EMC/EMI regulations.
MODEL
MAX OUTPUT WATTAGE[W]
DC OUTPUT
KHEA/KHNA90F-12
81.6
12V 6.8A
KHEA/KHNA90F-24
91.2
24V 3.8A
SPECIFICATIONS
MODEL
KHEA/KHNA90F-12
KHEA/KHNA90F-24
*10
VOLTAGE[V]
AC85 - 264 1f(Refer to “Derating”) or DC88-250
ACIN 115V 0.85typ
ACIN 230V 0.45typ
0.95typ
0.55typ
CURRENT[A]
FREQUENCY[Hz]
50 / 60 (45 - 66) or DC
ACIN 115V 87.0typ
ACIN 230V 88.0typ
89.0typ (88.0typ for option -E)
91.0typ (89.5typ for option -E)
EFFICIENCY[%]
INPUT
ACIN 115V 0.98typ
ACIN 230V 0.86typ
POWER FACTOR
(Io=100%)
ACIN 115V 18typ (Io=100%
）
(at cold start Ta=25
C
C
)
)
INRUSH CURRENT[A]
*
1
ACIN 230V 35typ (Io=100%
）
(at cold start Ta=25
LEAKAGE CURRENT[mA]
VOLTAGE[V]
0.45 / 0.75max (ACIN 100V / 240V 60Hz, Io=100%, According to IEC60950-1 and DEN-AN)
12
24
CURRENT[A]
6.8
3.8
PEAK CURRENT[A]
LINE REGULATION[mV]
LOAD REGULATION[mV]
-
-
*
*
2
2
48max
100max
96max
150max
200max
300max
300max
260max
360max
360max
240max
290max
96max
0 to +70C 200max
*
3
RIPPLE[mVp-p]
-20 - 0C
300max
*
*
4
4
*
*
4
4
Io=0 - 30% 300max
0 to +70C 260max
OUTPUT
*
3
RIPPLE NOISE[mVp-p]
-20 - 0C
360max
Io=0 - 30% 360max
0 to +70C 120max
-20 to +70C 150max
TEMPERATURE REGULATION[mV]
*
5
48max
DRIFT[mV]
START-UP TIME[ms]
HOLD-UP TIME[ms]
500typ (ACIN 115V, Io=100%)
20typ (ACIN 115V, Io=100%)
10.80 to 13.20
OUTPUT VOLTAGE ADJUSTMENT RANGE[V]
OUTPUT VOLTAGE SETTING[V]
OVERCURRENT PROTECTION
22.50 to 28.50 (Fixed for option -E)
24.00 to 24.96 (24.00 to 24.50 for option -E)
12.00 to 12.48
*
9
Works over 105% of rating (101% for option -E), recovers automatically
PROTECTION
CIRCUIT AND OVERVOLTAGE PROTECTION[V] 13.80 to 16.80
30.00 to 36.00 (26.40 to 33.60 for option -E)
OTHERS
DC_OK LAMP
LED (Green)
INPUT-OUTPUT
INPUT-PE
OUTPUT-PE
AC3,000V 1minute, Cutoff current = 10mA, DC500V 50M
AC2,000V 1minute, Cutoff current = 10mA, DC500V 50M
W
W
min
min
min
（
At Room Temperature
）
）
ISOLATION
（At Room Temperature
AC500V 1minute, Cutoff current = 100mA, DC500V 50M
W
（At Room Temperature
）
OPERATING TEMP.,HUMID.AND ALTITUDE
STORAGE TEMP.,HUMID.AND ALTITUDE
-20 to +70
C
, 20 - 90%RH (Non condensing), Type tested for -40
C
start-up (Refer to Derating”)
“
-30 to +85
C
, 20 - 90%RH (Non condensing)
ENVIRONMENT
2
*
8
VIBRATION
IMPACT
10 - 55Hz, 19.6m/s (2G), 3minutes period, 60 minutes along Z axis (Non operating, mounted on DIN Rail)
2
196.1m/s (20G), 11ms, X, Y and Z axis (Packing state)
AC input UL60950-1, C-UL (CSA60950-1), EN60950-1, UL508, NEC Class2 (24V output only option -E), ANSI/ISA12.12.01, ATEX, Complies with DEN-AN
DC input UL60950-1, C-UL (CSA60950-1), EN60950-1
AGENCY APPROVALS
SAFETY AND
NOISE
REGULATIONS
CONDUCTED NOISE
HARMONIC ATTENUATOR
CASE SIZE
Complies with FCC-B, VCCI-B, CISPR22-B, EN55011-B, EN55022-B
*
6
Complies with IEC61000-3-2
（
Class A)
*
7
50
X
90X
90mm (W
X
HX
D) [1.97 3.54X3.54 inches]
X
OTHERS
WEIGHT
405g max
COOLING METHOD
Convection
*
1
The value is primary surge. The current of input surge to a built-in EMI/EMC Filter(0.2ms or less)is
excluded.
input voltage held constant at the rated input/output.
Please contact us about another class.
*
*
*
6
7
8
*
*
2
3
Please contact us about dynamic load and input response.
Case size contains neither the umbo.
T
his is the value that measured on measuring board with capacitor of 22
mF and 0.1mF at 150mm from
Only as standard mounting orientation (A). Refer to the “Assembling and Installation Method”.
If install other than standard mounting orientation (A), please fix the power supply for withstand the
vibration and impact.
If the overcurrent protection circuit operates continuously, the output voltage shut down. Refer to
the instruction manual 1.3.
10 Under low DC input voltage below DC110V, the temperature derating -1
derating -1%/V are required.
output terminal.
Measured by 20MHz oscilloscope or Ripple-Noise meter (Equivalent to KEISOKU-GIKEN: RM103).
Please refer to the instruction manual 1.7.
Ripple and ripple noise spec is change at Io=0 to 30% by burst operation.
*
*
9
*
*
4
5
In case of operating under 0
30% load factor.
Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25
C
ambient temperature, the value is two times of specification at 0 to
C/V or the output power
C
, with the
*
*
To meet the specifications. Do not operate over-loaded condition.
A sound may occur from power supply at light or peak loading.
June 29, 2020
KH-6
KH series
Block diagram
FUSE
500VAC/400VDC
3.15A
INRUSH
CURRENT
LIMIT
AC IN 85～264V
DCIN 88～250V
NOISE
FILTER
RECTIFIER
PE
TRANSFORMER
RECTIFIER
AND
CONTROL
INVERTER
DC OUT
FILTER
BOOSTER
INDUCTOR
CURRENT
SENSING
RECTIFIER
AND
FILTER
CURRENT
SENSING
Photocoupler
Photocoupler
INVERTER
CONTROL
CONTROL
OVER VOLTAGE
PROTECTION
External view
<KHEA90F(Euro Style I/O Terminals)>
<KHNA90F(Barrier Blocks Style I/O Terminals)>
15.5
[0.61]
6.4
[0.25]
90
[3.54]
15.7
[0.62]
9.3
[0.37]
90
[3.54]
TB2
TB2
6-M3.5
Output terminal(+)
Output terminal(
LED(DC_OK)
Output terminal(+)
Output terminal(
LED(DC_OK)
-)
-
)
Output voltage
adjustable potentiometer
Output voltage
adjustable potentiometer
AC(L)
AC(L)
AC(N)
PE
AC(N)
PE
TB1
TB1
15.5
15.7
[0.62]
9.5
94.5
[3.72]
9.3
94.5
[3.72]
[0.61]
11.2
[0.44]
[0.37]
[0.37]
Name plate
Name plate
11.2
[0.44]
50
[1.97]
50
[1.97]
¶ Tolerance : 1 [ 0.04]
¶ Weight : 405g max
¶ PCB Material/thickness : FR-4 / 1.6mm [0.06]
¶ Chassis-Case material : PBT
¶ Tolerance : 1 [ 0.04]
¶ Weight : 405g max
¶ PCB Material/thickness : FR-4 / 1.6mm [0.06]
¶ Chassis-Case material : PBT
¶ Din rail attachment material : PC/ABS
¶ Dimensions in mm, [ ] = inches
¶ Screw tightening torque : 1N-m max
¶ Din rail attachment material : PC/ABS
¶ Dimensions in mm, [ ] = inches
¶ Screw tightening torque : 1.1N-m max
June 29, 2020
KH-7
Ordering information
AC-DC Power Supplies DIN Rail Type
KHO A -120 F
-24 -O
6
KHEA/KHNA120F
1
2
3
4
5
1
Series name
Example recommended EMI/EMC filter
NAC-04-472-D
R
KHE
KHN
：Euro style I/O terminals
：Barrier blocks style
I/O terminals
2
3
4
5
6
Single output
Output wattage
Universal input
Output voltage
Option
C : with Coating
N2: Screw mounting
UL508
High voltage pulse noise type : NAP series
Low leakage current type : NAM series
*
A higher current rating EMI/EMC filter
may be recommended in view of the
other devices that could be connected
in parallel with the power supply.
*Make sure necessary tests will be carried out on your end equipment with the power supply installed in accordance with any required EMC/EMI regulations.
MODEL
MAX OUTPUT WATTAGE[W]
DC OUTPUT
KHEA / KHNA120F-24
120
24V 5A (Peak 7.5A)
SPECIFICATIONS
MODEL
KHEA / KHNA120F-24
*
10
VOLTAGE[V]
AC85 - 264 1for DC88 - 370
ACIN 115V 1.2typ
ACIN 230V 0.6typ
CURRENT[A]
FREQUENCY[Hz]
50 / 60 (45 - 66) or DC
ACIN 115V 90typ
ACIN 230V 92typ
EFFICIENCY[%]
INPUT
ACIN 115V 0.98typ
ACIN 230V 0.93typ
POWER FACTOR
ACIN 115V 15typ (at cold start Ta=25
ACIN 230V 30typ (at cold start Ta=25
C
)
)
INRUSH CURRENT[A]
*
1
C
LEAKAGE CURRENT[mA]
VOLTAGE[V]
0.45 / 0.75max (ACIN 100V / 240V 60Hz, Io=100%, According to IEC60950-1 and DEN-AN)
24
CURRENT[A]
5
*
*
*
2
3
3
PEAK CURRENT[A]
LINE REGULATION[mV]
LOAD REGULATION[mV]
7.5
96max
150max
*
*
4
4
0 to +70C 120max
-25 - 0C
*
5
RIPPLE[mVp-p]
240max
Io=0 - 30% 240max
0 to +70C 150max
OUTPUT
*
5
RIPPLE NOISE[mVp-p]
-25 - 0C
300max
*
*
*
4
4
4
Io=0 - 30% 300max
0 to +70C 240max
-25 to +70C 360max
TEMPERATURE REGULATION[mV]
*
6
96max
DRIFT[mV]
START-UP TIME[ms]
HOLD-UP TIME[ms]
750max (ACIN 115V, Io=100%)
20typ (ACIN 115V, Io=100%)
22.5 to 28.5
OUTPUT VOLTAGE ADJUSTMENT RANGE[V]
OUTPUT VOLTAGE SETTING[V]
OVERCURRENT PROTECTION
24.0 1.0%
Works over 101% of peak current and recovers automatically
OVERVOLTAGE PROTECTION[V] 30.0 to 36.0
PROTECTION
CIRCUIT AND
OTHERS
REMOTE ON/OFF (RC)
DC_OK LAMP
Provided
LED (Green)
ALARM LAMP
LED (Red)
DC_OK CONTACT
INPUT-OUTPUT
INPUT-PE
Relay contact 30VDC 1A max, 30VAC 0.5A max (resistive load) (Only KHEA)
AC3,000V 1minute, Cutoff current = 10mA, DC500V 50M
AC2,000V 1minute, Cutoff current = 10mA, DC500V 50M
W
W
min
min
min
min
（
At Room Temperature
）
）
）
（At Room Temperature
ISOLATION
OUTPUT-PE
AC500V 1minute, Cutoff current = 100mA, DC500V 50M
W
（
（
At Room Temperature
At Room Temperature
OUTPUT-RC, DC_OK
OPERATING TEMP.,HUMID.AND ALTITUDE
STORAGE TEMP.,HUMID.AND ALTITUDE
AC500V 1minute, Cutoff current = 100mA, DC500V 50M
W
）
-25 to +70
C
, 20 - 90%RH (Non condensing), Type tested for -40
C
start-up (Refer to
“
Derating”)
-40 to +85
C
, 20 - 90%RH (Non condensing)
ENVIRONMENT
2
*
9
VIBRATION
IMPACT
10 - 55Hz, 19.6m/s (2G), 3minutes period, 60 minutes along Z axis (Non operating, mounted on DIN Rail)
2
196.1m/s (20G), 11ms, once each X, Y and Z axis (Packing state)
AC input UL60950-1, C-UL (CSA60950-1), EN60950-1, UL508, ANSI/ISA12.12.01, ATEX, GL, Complies with DEN-AN
DC input UL60950-1, C-UL (CSA60950-1), EN60950-1
AGENCY APPROVALS
SAFETY AND
NOISE
REGULATIONS
CONDUCTED NOISE
HARMONIC ATTENUATOR
CASE SIZE
Complies with FCC-B, VCCI-B, CISPR22-B, EN55011-B, EN55022-B
*7
Complies with IEC61000-3-2
（
Class A)
*
8
37
580g max
Convection
X
124
X
117mm (W
X
HX
D) [1.46 4.88X4.61 inches]
X
OTHERS
WEIGHT
COOLING METHOD
June 29, 2020
KH-8
KH series
*
1
The value is primary surge. The current of input surge to a built-in EMI/EMC
Filter(0.2ms or less)is excluded.
Measured by 20MHz oscilloscope or Ripple-Noise meter (Equivalent to
KEISOKU-GIKEN: RM103).
*
9
Only as standard mounting orientation (A). Refer to the
Installation Method
“Assembling and
”.
*2
*3
*4
Refer to 2, instruction manual.
Please refer to the instruction manual 1.7.
If install other than standard mounting orientation (A), please fix the power
Please contact us about dynamic load and input response.
The output voltage is below 23.5V, the value is equal to three times of the
specification.
*
6
Drift is the change in DC output for an eight hour period after a half-hour
supply for withstand the vibration and impact.
warm-up at 25
C
, with the input voltage held constant at the rated input/
*
10 Under low DC input voltage below DC110V, the temperature derating
-1 /V or the output power derating -1%/V are required.
output.
C
*5
This is the value that measured on measuring board with capacitor of 22
m
F
*
*
7
8
Please contact us about another class.
Case size contains neither the umbo.
*
*
To meet the specifications. Do not operate over-loaded condition.
A sound may occur from power supply at light or peak loading.
and 0.1 F at 150mm from output terminal.
m
Block diagram
FUSE
500VAC/400VDC 5A
AC IN 85～264V
DC IN 88～370V
NOISE
FILTER
RECTIFIER
PE
BOOSTER
INDUCTOR
CURRENT
SENSING
TRANSFORMER
INRUSH
CURRENT
LIMIT
RECTIFIER
AND
FILTER
RECTIFIER
AND
FILTER
INVERTER
DC OUT
INVERTER
CONTROL
CURRENT
SENSING
Photocoupler
Photocoupler
OVER VOLTAGE
PROTECTION
CONTROL
CONTROL
PhotoMosRelay
DC_OK (Only KHEA)
RC (Remote ON/OFF)
Photocoupler
External view
<KHEA120F(Euro Style I/O Terminals)>
<KHNA120F(Barrier Blocks Style I/O Terminals)>
-RC
+RC
-RC
+RC
9
[0.35]
6.4
[0.25]
111.2
[4.38]
8.5
[0.33]
10
[0.39]
6-M4
2
[0.08]
111.2
[4.38]
Output terminal(+)
DC_OK
Output terminal(+)
Output terminal(-)
Output terminal(-)
LED(ALARM)
LED(DC_OK)
LED(ALARM)
LED(DC_OK)
Output voltage
Name plate
Name plate
Output voltage
adjustable potentiometer
adjustable potentiometer
AC(L)
AC(N)
PE
AC(L)
AC(N)
PE
117
15.5
[0.61]
9
117
15.5
[0.61]
[4.61]
[4.61]
121.2
[4.77]
121.2
[4.77]
9.5
[0.37]
37
[1.46]
8.5
10
[0.33]
[0.39]
37
[0.35]
[1.46]
Tolerance : ±1 [±0.04]
Weight : 580g max
Tolerance : ±1 [±0.04]
Weight : 580g max
PCB Material/thickness : FR-4 / 1.6mm [0.06]
Chassis material : Aluminum
PCB Material/thickness : FR-4 / 1.6mm [0.06]
Chassis material : Aluminum
Case material : Stainless steel
Case material : Stainless steel
DIN rail attachment material : Aluminum, Stainless steel, Nylon
Dimensions in mm, [ ] = inches
DIN rail attachment material : Aluminum, Stainless steel, Nylon
Dimensions in mm, [ ] = inches
Screw tightening torque : 1N m max
Screw tightening torque : 1.6N m max
June 29, 2020
KH-9
Ordering information
AC-DC Power Supplies DIN Rail Type
KHO A -240 F
-24 -O
6
KHEA/KHNA240F
1
2
3
4
5
1
Series name
Example recommended EMI/EMC filter
NAC-06-472-D
R
KHE
KHN
：Euro style I/O terminals
：Barrier blocks style
I/O terminals
2
3
4
5
6
Single output
Output wattage
Universal input
Output voltage
Option
C : with Coating
N2: Screw mounting
UL508
High voltage pulse noise type : NAP series
Low leakage current type : NAM series
*
A higher current rating EMI/EMC filter
may be recommended in view of the
other devices that could be connected
in parallel with the power supply.
*Make sure necessary tests will be carried out on your end equipment with the power supply installed in accordance with any required EMC/EMI regulations.
MODEL
MAX OUTPUT WATTAGE[W]
DC OUTPUT
KHEA / KHNA240F-24
240
24V 10A (Peak 15A)
SPECIFICATIONS
MODEL
KHEA / KHNA240F-24
*
10
VOLTAGE[V]
AC85 - 264 1for DC88 - 370
ACIN 115V 2.3typ
ACIN 230V 1.2typ
CURRENT[A]
FREQUENCY[Hz]
50 / 60 (45 - 66) or DC
ACIN 115V 92typ
EFFICIENCY[%]
INPUT
ACIN 230V 94typ
ACIN 115V 0.98typ
ACIN 230V 0.93typ
POWER FACTOR
ACIN 115V 20typ (more than 3 sec. to re-start)
ACIN 230V 40typ (more than 3 sec. to re-start)
INRUSH CURRENT[A]
*
1
LEAKAGE CURRENT[mA]
VOLTAGE[V]
0.45 / 0.75max (ACIN 100V / 240V 60Hz, Io=100%, According to IEC60950-1 and DEN-AN)
24
CURRENT[A]
10
*
*
*
2
3
3
PEAK CURRENT[A]
LINE REGULATION[mV]
LOAD REGULATION[mV]
15
96max
150max
*
*
4
4
0 to +70C 120max
-25 - 0C
*
5
RIPPLE[mVp-p]
240max
Io=0 - 30% 240max
0 to +70C 150max
OUTPUT
*
5
RIPPLE NOISE[mVp-p]
-25 - 0C
300max
*
*
*
4
4
4
Io=0 - 30% 300max
0 to +70C 240max
-25 to +70C 360max
TEMPERATURE REGULATION[mV]
*
6
96max
DRIFT[mV]
START-UP TIME[ms]
HOLD-UP TIME[ms]
750max (ACIN 115V, Io=100%)
20typ (ACIN 115V, Io=100%)
22.5 to 28.5
OUTPUT VOLTAGE ADJUSTMENT RANGE[V]
OUTPUT VOLTAGE SETTING[V]
OVERCURRENT PROTECTION
24.0 1.0%
Works over 101% of peak current and recovers automatically
OVERVOLTAGE PROTECTION[V] 30.0 to 36.0
PROTECTION
CIRCUIT AND
OTHERS
REMOTE ON/OFF (RC)
DC_OK LAMP
Provided
LED (Green)
ALARM LAMP
LED (Red)
DC_OK CONTACT
INPUT-OUTPUT
INPUT-PE
Relay contact 30VDC 1A max, 30VAC 0.5A max (resistive load) (Only KHEA)
AC3,000V 1minute, Cutoff current = 10mA, DC500V 50M
AC2,000V 1minute, Cutoff current = 10mA, DC500V 50M
W
W
min
min
min
min
（
At Room Temperature
）
）
）
（At Room Temperature
ISOLATION
OUTPUT-PE
AC500V 1minute, Cutoff current = 100mA, DC500V 50M
W
（
（
At Room Temperature
At Room Temperature
OUTPUT-RC, DC_OK
OPERATING TEMP.,HUMID.AND ALTITUDE
STORAGE TEMP.,HUMID.AND ALTITUDE
AC500V 1minute, Cutoff current = 100mA, DC500V 50M
W
）
-25 to +70
-40 to +85
C
C
, 20 - 90%RH (Non condensing), Type tested for -40
C
start-up (Refer to
“
Derating”)
, 20 - 90%RH (Non condensing)
ENVIRONMENT
2
*
9
VIBRATION
IMPACT
10 - 55Hz, 19.6m/s (2G), 3minutes period, 60 minutes along Z axis (Non operating, mounted on DIN Rail)
2
196.1m/s (20G), 11ms, once each X, Y and Z axis (Packing state)
AC input UL60950-1, C-UL (CSA60950-1), EN60950-1, UL508, ANSI/ISA12.12.01, ATEX, GL, Complies with DEN-AN
DC input UL60950-1, C-UL (CSA60950-1), EN60950-1
AGENCY APPROVALS
SAFETY AND
NOISE
REGULATIONS
CONDUCTED NOISE
HARMONIC ATTENUATOR
CASE SIZE
Complies with FCC-B, VCCI-B, CISPR22-B, EN55011-B, EN55022-B
*
7
Complies with IEC61000-3-2
（
Class A)
*
8
50
900g max
Convection
X
124
X
117mm (W
X
HX
D) [1.97 4.88X4.61 inches]
X
OTHERS
WEIGHT
COOLING METHOD
June 29, 2020
KH-10
KH series
*
1
The value is primary surge. The current of input surge to a built-in EMI/EMC
Filter(0.2ms or less)is excluded.
Measured by 20MHz oscilloscope or Ripple-Noise meter (Equivalent to
KEISOKU-GIKEN: RM103).
*
9
Only as standard mounting orientation (A). Refer to the
Installation Method
“Assembling and
”.
*2
*3
*4
Refer to 2, instruction manual.
Please refer to the instruction manual 1.7.
If install other than standard mounting orientation (A), please fix the power
Please contact us about dynamic load and input response.
The output voltage is below 23.5V, the value is equal to three times of the
specification.
*
6
Drift is the change in DC output for an eight hour period after a half-hour
supply for withstand the vibration and impact.
warm-up at 25
C
, with the input voltage held constant at the rated input/
*
10 Under low DC input voltage below DC110V, the temperature derating
-1 /V or the output power derating -1%/V are required.
output.
C
*5
This is the value that measured on measuring board with capacitor of 22
m
F
*
*
7
8
Please contact us about another class.
Case size contains neither the umbo.
*
*
To meet the specifications. Do not operate over-loaded condition.
A sound may occur from power supply at light or peak loading.
and 0.1 F at 150mm from output terminal.
m
Block diagram
FUSE
500VAC/400VDC 8A
AC IN 85～264V
DC IN 88～370V
NOISE
FILTER
RECTIFIER
PE
BOOSTER
INDUCTOR
CURRENT
SENSING
TRANSFORMER
INRUSH
CURRENT
LIMIT
RECTIFIER
AND
FILTER
RECTIFIER
AND
FILTER
INVERTER
DC OUT
INVERTER
CONTROL
CURRENT
SENSING
Photocoupler
Photocoupler
OVER VOLTAGE
PROTECTION
CONTROL
CONTROL
PhotoMosRelay
DC_OK (Only KHEA)
RC (Remote ON/OFF)
Photocoupler
External view
<KHEA240F(Euro Style I/O Terminals)>
<KHNA240F(Barrier Blocks Style I/O Terminals)>
-RC
+RC
-RC
+RC
10
[0.39]
10
[0.39]
9.1
[0.36]
6.4
[0.25]
2
[0.08]
111.2
[4.38]
7-M4
111.2
[4.38]
DC_OK
Output terminal(+)
Output terminal(+)
Output terminal(-)
Output terminal(-)
LED(ALARM)
LED(DC_OK)
Name plate
LED(ALARM)
LED(DC_OK)
Output voltage
Name plate
Output voltage
adjustable potentiometer
adjustable potentiometer
AC(L)
AC(N)
AC(L)
AC(N)
PE
PE
15.5
[0.61]
15
117
117
[4.61]
[4.61]
10
[0.39]
9.5
[0.37]
50
[1.97]
15.5
[0.61]
121.2
[4.77]
121.2
[4.77]
[0.59]
50
[1.97]
Tolerance : ±1 [±0.04]
Weight : 900g max
Tolerance : ±1 [±0.04]
Weight : 900g max
PCB Material/thickness : FR-4 / 1.6mm [0.06]
Chassis material : Aluminum
PCB Material/thickness : FR-4 / 1.6mm [0.06]
Chassis material : Aluminum
Case material : Stainless steel
Case material : Stainless steel
DIN rail attachment material : Aluminum, Stainless steel, Nylon
Dimensions in mm, [ ] = inches
DIN rail attachment material : Aluminum, Stainless steel, Nylon
Dimensions in mm, [ ] = inches
Screw tightening torque : 1N m max
Screw tightening torque : 1.6N m max
June 29, 2020
KH-11
Ordering information
AC-DC Power Supplies DIN Rail Type
KHO A 480
F -OO -O
KHEA/KHNA480F
1
2
3
4
5
6
1
Series name
Example recommended EMI/EMC filter
NAC-10-472-D
R
KHE
：Euro style I/O terminals
KHN：
Barrier blocks style
I/O terminals
2
3
4
5
6
Single output
Output wattage
Universal input
Output voltage
Option
C : with Coating
N2: Screw mounting
UL508
High voltage pulse noise type : NAP series
Low leakage current type : NAM series
*
A higher current rating EMI/EMC filter
may be recommended in view of the
other devices that could be connected
in parallel with the power supply.
*Make sure necessary tests will be carried out on your end equipment with the power supply installed in accordance with any required EMC/EMI regulations.
MODEL
MAX OUTPUT WATTAGE[W]
DC OUTPUT
KHEA / KHNA480F-24
480
24V 20A (Peak 30A)
KHEA / KHNA480F-48
480
48V 10A (Peak 15A)
SPECIFICATIONS
MODEL
KHEA / KHNA480F-24
KHEA / KHNA480F-48
*
10
VOLTAGE[V]
AC85 - 264 1f(Output derating is required) or DC88 - 350
ACIN 115V 4.6typ
ACIN 230V 2.3typ
CURRENT[A]
FREQUENCY[Hz]
50 / 60 (45 - 66) or DC
ACIN 115V 92typ
ACIN 230V 94typ
EFFICIENCY[%]
INPUT
ACIN 115V 0.98typ
ACIN 230V 0.93typ
POWER FACTOR
ACIN 115V 20typ (more than 3 sec. to re-start)
ACIN 230V 40typ (more than 3 sec. to re-start)
INRUSH CURRENT[A]
*
1
LEAKAGE CURRENT[mA]
VOLTAGE[V]
0.75 / 1.5max (ACIN 100V / 240V 60Hz, Io=100%, According to IEC60950-1 and DEN-AN)
24
48
CURRENT[A]
20
10
*
*
*
2
3
3
PEAK CURRENT[A]
LINE REGULATION[mV]
LOAD REGULATION[mV]
30
15
*
9
9
*
*
9
9
96max (Io=30-100%)
150max (Io=30-100%)
192max (Io=30-100%)
300max (Io=30-100%)
120max
*
0 to +70C 120max
*
4
RIPPLE[mVp-p]
-25 - 0C
240max
240max
Io=0 - 30% 500max
0 to +70C 150max
750max
150max
300max
OUTPUT
*
4
RIPPLE NOISE[mVp-p]
-25 - 0C
300max
Io=0 - 30% 600max
0 to +70C 240max
-25 to +70C 360max
750max
480max
600max
TEMPERATURE REGULATION[mV]
*
5
96max
DRIFT[mV]
192max
START-UP TIME[ms]
HOLD-UP TIME[ms]
750max (ACIN 115V, Io=100%)
20typ (ACIN 115V, Io=100%)
22.5 to 26.4
OUTPUT VOLTAGE ADJUSTMENT RANGE[V]
OUTPUT VOLTAGE SETTING[V]
OVERCURRENT PROTECTION
45.0 to 55.2
48.0 1.0%
24.0 1.0%
Works over 101% of peak current and recovers automatically
57.6 to 67.2
OVERVOLTAGE PROTECTION[V] 30.0 to 36.0
PROTECTION
CIRCUIT AND
OTHERS
REMOTE ON/OFF (RC)
DC_OK LAMP
ALARM LAMP
Provided
LED (Green)
LED (Red)
DC_OK CONTACT
INPUT-OUTPUT
INPUT-PE
Relay contact 30VDC 1A max, 30VAC 0.5A max (resistive load) (Only KHEA)
AC3,000V 1minute, Cutoff current = 10mA, DC500V 50M
AC2,000V 1minute, Cutoff current = 10mA, DC500V 50M
W
W
min
min
min
min
（
At Room Temperature
）
）
）
（At Room Temperature
ISOLATION
OUTPUT-PE
AC500V 1minute, Cutoff current = 100mA, DC500V 50M
W
（
（
At Room Temperature
At Room Temperature
OUTPUT-RC, DC_OK
OPERATING TEMP.,HUMID.AND ALTITUDE
STORAGE TEMP.,HUMID.AND ALTITUDE
AC500V 1minute, Cutoff current = 100mA, DC500V 50M
W
）
-25 to +70
-40 to +85
C
C
, 20 - 90%RH (Non condensing), Type tested for -40
C
start-up (Refer to
“
Derating”)
, 20 - 90%RH (Non condensing)
ENVIRONMENT
2
*
8
VIBRATION
IMPACT
10 - 55Hz, 19.6m/s (2G), 3minutes period, 60 minutes along Z axis (Non operating, mounted on DIN Rail)
2
196.1m/s (20G), 11ms, once each X, Y and Z axis (Packing state)
AC input UL60950-1, C-UL (CSA60950-1), EN60950-1, UL508, ANSI/ISA12.12.01, ATEX, GL (Only 24V), Complies with DEN-AN
DC input UL60950-1, C-UL (CSA60950-1), EN60950-1
AGENCY APPROVALS
SAFETY AND
NOISE
REGULATIONS
CONDUCTED NOISE
HARMONIC ATTENUATOR
CASE SIZE
Complies with FCC-B, VCCI-B, CISPR22-B, EN55011-B, EN55022-B
*
6
Complies with IEC61000-3-2
（
Class A)
*
7
70
X
124X
117mm (W
X
HX
D) [2.76 4.88X4.61 inches]
X
OTHERS
WEIGHT
COOLING METHOD
1,200g max
Convection
June 29, 2020
KH-12
KH series
*
1
The value is primary surge. The current of input surge to a built-in EMI/EMC
Filter(0.2ms or less)is excluded.
Please refer to the instruction manual 1.7.
Drift is the change in DC output for an eight hour period after a half-hour
If install other than standard mounting orientation (A), please fix the power
supply for withstand the vibration and impact.
*
5
*2
*3
*4
Refer to 3, instruction manual.
warm-up at 25
C
, with the input voltage held constant at the rated input/
*
*
9
Burst operation at 30% load or less.
Please contact us about dynamic load and input response.
output.
10 Under low DC input voltage below DC110V, the temperature derating
This is the value that measured on measuring board with capacitor of 22
m
F
*
*
*
6
7
8
Please contact us about another class.
-1C/V or the output power derating -1%/V are required.
and 0.1mF at 150mm from output terminal.
Case size contains neither the umbo.
*
*
To meet the specifications. Do not operate over-loaded condition.
A sound may occur from power supply at light or peak loading.
Measured by 20MHz oscilloscope or Ripple-Noise meter (Equivalent to
Only as standard mounting orientation (A). Refer to the “Assembling and
KEISOKU-GIKEN: RM103).
Installation Method”.
Block diagram
FUSE
500VAC/400VDC 16A
INRUSH
CURRENT
LIMIT
AC IN 85～264V
DC IN 88～350V
NOISE
FILTER
RECTIFIER
PE
BOOSTER
INDUCTOR
CURRENT
SENSING
TRANSFORMER
RECTIFIER
AND
RECTIFIER
AND
INVERTER
DC OUT
FILTER
FILTER
INVERTER
CONTROL
CURRENT
SENSING
Photocoupler
Photocoupler
OVER VOLTAGE
PROTECTION
CONTROL
CONTROL
PhotoMosRelay
DC_OK (Only KHEA)
RC (Remote ON/OFF)
Photocoupler
External view
<KHEA480F(Euro Style I/O Terminals)>
<KHNA480F(Barrier Blocks Style I/O Terminals)>
-RC +RC
-RC +RC
111.2
[4.38]
2
[0.08]
111.2
[4.38]
27.1
[1.07]
6.4
[0.25]
7-M4
30.4
[1.2]
10
[0.39]
DC_OK
Output terminal(+)
Output terminal(-)
Output terminal(+)
Output terminal(-)
LED(ALARM)
LED(DC_OK)
Output voltage
LED(ALARM)
LED(DC_OK)
Name plate
Name plate
Output voltage
adjustable potentiometer
adjustable potentiometer
AC(L)
AC(N)
PE
AC(L)
AC(N)
PE
16.5
16.5
[0.65]
25
[0.98]
117
117
[0.65]
[4.61]
[4.61]
25.5
[1]
9.5
[0.37]
10
[0.39]
70
[2.76]
121.2
[4.77]
121.2
[4.77]
70
[2.76]
Tolerance : ±1 [±0.04]
Weight : 1,200g max
Tolerance : ±1 [±0.04]
Weight : 1,200g max
PCB Material/thickness : FR-4 / 1.6mm [0.06]
Chassis material : Aluminum
PCB Material/thickness : FR-4 / 1.6mm [0.06]
Chassis material : Aluminum
Case material : Stainless steel
Case material : Stainless steel
DIN rail attachment material : Aluminum, Stainless steel, Nylon
Dimensions in mm, [ ] = inches
DIN rail attachment material : Aluminum, Stainless steel, Nylon
Dimensions in mm, [ ] = inches
Screw tightening torque : 1N m max
Screw tightening torque : 1.6N m max
June 29, 2020
KH-13
KH-series
Terminal Blocks
KHEA30F
KHNA30F
¿
¿
4
5
4
5
6
7
6
7
3
2
1
3
2
1
KHEA60F
KHNA60F
¿
¿
4
4
5
5
6
7
6
7
3
2
1
3
2
1
KHEA90F
KHNA90F
¿
¿
4
5
4
5
6
7
6
7
3
2
3
2
1
1
Terminal
Number
Terminal
Name
Function
PE
Protective earth Terminal
Input Terminals
1
2
3
4
5
6
7
AC (N)
AC (L)
+VOUT
+Output Terminals
-Output Terminals
LED for output voltage confirmation
Adjustment of output voltage
-
VOUT
DC_OK
TRM
June 29, 2020
KH-14
KH-series
Terminal Blocks
KHEA120F
KHNA120F
¿
5
6
¿
4 5
6
7
7
8
9
0
å
0
å
8
9
1
2
3
1
5
2
3
KHEA240F
KHNA240F
¿
¿
4
5
6
6
7
8
9
7
8
9
0
0
å
å
1
2
3
1
2
3
KHEA480F
KHNA480F
¿
¿
5
6
4
5 6
7
8
9
7
8
9
0
0
å
å
1
2
3
1
2
3
Terminal
Number
Terminal
Name
Terminal
Number
Terminal
Name
Function
Function
PE
AC (N)
AC (L)
DC_OK
+VOUT
Protective earth Terminal
Input Terminals
ALARM
DC_OK
TRM
+RC
-RC
LED Alarm for lowered output voltage
LED for output voltage confirmation
Adjustment of output voltage
1
2
3
4
5
6
7
8
9
0
å
Output voltage confirmation(relay contact)
+Output Terminals
-Output Terminals
Remote ON/OFF Terminals
-
VOUT
June 29, 2020
KH-15
KH-series
Assembling and Installation Method
INPUT
OUTPUT
OUTPUT
Installation method
INPUT
DIN rail
About DIN-Rail Attachment available with DIN EN60715 TH 35
(35×7.5mm or 35×15mm) (Top hat shaped DIN rail)
Below shows mounting orientation.
¡
¡
If install other then standard mounting orientation (A), please
fix the power supply for withstand the impact and vibration.
INPUT
OUTPUT
(A) Standard
(B)
(C)
INPUT
OUTPUT
OUTPUT
INPUT
(D)
(E)
When you mount a power supply on a DIN rail, have the area
marked A catch one side of the rail and push the unit to the
direction of B. To remove the power supply from the rail, either
push down the area marked C or insert a tool such as driver to
the area marked D and pull the unit apart from the rail.
¡
C
E
A
When you couldn’t remove the unit easily, push down the area
marked C while lightly pushing the unit to the direction of E.
B
D
Shown below the notes about installation clearance of a unit.
¡
1
2
Convection
25mm
or more
KHEA30F/60F/90F, KHNA30F/60F/90F
¿
Installation clearance at above and below the unit.
Please have clearance of at least 25mm above and below the
unit to avoid heat accumulation.
1
Installation clearance at the side of the unit.
2
Please have clearance of at least 5mm side the unit to insu-
lating the internal components. However, refer to right figure,
if adjacent device of the unit (including power supply) is a
heat source.
1
25mm
Convection
or more
Adjacent device of the unit
Non-heat source Heat source(
No.
Model
)
*
1
2
3
KHEA30F, KHNA30F
KHEA60F, KHNA60F
KHEA90F, KHNA90F
5mm or more 15mm or more
5mm or more 15mm or more
5mm or more 15mm or more
Reference value when same power units are adjacent.
*
June 29, 2020
KH-16
KH-series
Assembling and Installation Method
KHEA120F/240F/480F,KHNA120F/240F/480F
¿
1
Convection
2
25mm
Installation clearance at above and below the unit.
Please have clearance of at least 25mm above and below the
unit to avoid heat accumulation.
1
or more
Installation clearance at the side of the unit.
2
Please have clearance of at least 15mm side the unit to avoid
interfering with heat radiation from housing. However, refer to
right figure, if adjacent device of the unit (including power supply) is
a heat source.
1
25mm
Convection
or more
Adjacent device of the unit
Non-heat source Heat source(
15mm or more
15mm or more
15mm or more 50mm or more
No.
Model
)
*
1
2
3
KHEA120F, KHNA120F
KHEA240F, KHNA240F
KHEA480F, KHNA480F
Reference value when same power units are adjacent.
*
Derating
Derating curve for input voltage
KHEA30F/60F/90F, KHNA30F/60F/90F
KHEA480F, KHNA480F
¿
¿
[%]
[%]
100
100
80
80
85 90
85
100
[AC V]
[AC V]
Ambient temperature derating
The operative ambient temperature as different by input voltage. Derating curve is shown below.
In the hatched area,the specification of Ripple,Ripple Noise is different from other area.
¡
¡
Derating Curve (Convection)
¡
¡
Refer to instruction manual 4 for Ambient temperature measurement point.
KHEA30F, KHNA30F
¿
(C), (D), (E)
(B)
(A)
(D), (E)
(B), (C)
(A)
100
80
70
60
100
80
70
60
*
Vin=AC170V - 264V
Vin=AC85V - 170V
40
30
20
40
30
20
0
0
-30 -20 -10
0
10 20 30 40 50 60 70 80
-30 -20 -10
0
10 20 30 40 45 50 60 70 80
Ambient Temperature [C]
Ambient Temperature [C]
*Derating curve depend on input voltage is required.
June 29, 2020
KH-17
KH-series
Derating
KHEA60F, KHNA60F
¿
¿
¿
(B), (D), (E)
(C)
(A)
(E)
(C), (D)
(B)
(A)
100
80
100
80
60
60
50
*
Vin=AC170V - 264V
Vin=AC85V - 170V
4045
40
35
30
20
30
20
0
0
-30 -20 - 10
0
10 20 30 4045505560 70 80
-30 -20 -10
0
10 20 30 40 50 5560 70 80
Ambient Temperature [C]
Ambient Temperature [C]
*Derating curve depend on input voltage is required.
KHEA90F, KHNA90F
(C)
(B), (D), (E)
(A)
(D), (E)
(B), (C)
(A)
100
80
100
80
60
60
*
Vin=AC170V - 264V
Vin=AC85V - 170V
40
30
20
40
30
20
0
0
-30 -20 - 10
0
10 20 30 40 5055606570 80
-30 -20 -10
0
10 20 30 4045505560 70 80
Ambient Temperature [C]
Ambient Temperature [C]
*Derating curve depend on input voltage is required.
KHEA120F, KHNA120F
(C), (D), (E)
(B) (A)
(C), (D), (E)
(B)
(A)
100
100
80
75
80
75
60
60
50
40
30
20
Vin=AC170V - 264V
Vin=AC85V - 170V
40
30
20
0
0
-30 -20 -10
0
10 20 30 40 50 60 70 80
-30 -20 -10
0
10 20 30 40 50 60 70 80
Ambient Temperature [C]
Ambient Temperature [C]
KHEA240F, KHNA240F
¿
(C), (D), (E)
(B)
(A)
(C), (D), (E)
(B)
(A)
100
100
80
75
80
60
50
40
30
20
60
50
40
30
20
Vin=AC170V - 264V
Vin=AC85V - 170V
0
0
-30 -20 -10
0
10 20 30 40 50 60 70 80
-30 -20 -10
0
10 20 30 40 50 60 70 80
Ambient Temperature [C]
Ambient Temperature [C]
June 29, 2020
KH-18
KH-series
Derating
KHEA480F, KHNA480F
¿
(B)
(D), (E)
(C) (A)
(B)
(D), (E)
(C)
(A)
100
100
80
80
60
50
40
30
20
60
50
40
30
20
*
Vin=AC170V - 264V
Vin=AC85V - 170V
0
0
-30 -20 -10
0
10 20 2530 40 50 60 70 80
0
10 20 30 40 50 60 70 80
-30 -20 -10
Ambient Temperature [C]
Ambient Temperature [C]
*Derating curve depend on input voltage is required.
Derating Curve (Forced air)
¡
¡
Use the temperature measurement point as shown in instruction manual 4. Please use at the temperature dose not exceed the values in
instruction manual 4.
KHEA30F/60F/90F, KHNA30F/60F/90F
KHEA120F/240F, KHNA120F/240F
¿
¿
(A) - (E)
(A) - (E)
100
100
80
80
60
60
*
Vin=AC85V - 264V
Forced air
Vin=AC85V - 264V
Forced air (0.5m3/min)
40
40
30
20
30
20
0
0
-30 -20 -10
0
10 20 30 40 50 60 70 80
-30 -20 -10
0
10 20 30 40 50 60 70 80
Ambient Temperature [C]
Ambient Temperature [C]
*Derating curve depend on input voltage is required.
KHEA480F, KHNA480F
¿
(A) - (E)
100
80
60
*
Vin=AC85V - 264V
40
30
20
Forced air
0
-30 -20 -10
0
10 20 30 40 50 60 70 80
Ambient Temperature [C]
*Derating curve depend on input voltage is required.
June 29, 2020
KH-19
KH-series
Instruction Manual
◆ It is neccessary to read the “Instruction Manual” and “Before using our product” before you use our product.
Instruction Manual
https://en.cosel.co.jp/product/powersupply/KH/
https://en.cosel.co.jp/technical/caution/index.html
Before using our product
KH
NOTICE
Basic Characteristics Data
Series/Parallel
operation availability
Inrush
current
protection
circuit
Switching
frequency current
[kHz] [A]
*1
Input
PCB/Pattern
Rated
input fuse
Model
Circuit method
Single Double Series Parallel
sided sided operation operation
Material
*
2
KHEA30F
KHNA30F
KHEA60F
KHNA60F
KHEA90F
KHNA90F
KHEA120F
KHNA120F
KHEA240F
KHNA240F
KHEA480F
KHNA480F
500VAC/400VDC
3.15A
Flyback converter 50 - 200
0.55
1.10
0.95
1.2
Thermistor FR-4
Thermistor FR-4
Thermistor FR-4
Thermistor FR-4
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
No
No
No
No
No
No
500VAC/400VDC
3.15A
Flyback converter
50 - 200
Active filter
Flyback converter
Active filter
20 - 500
50 - 200
60 - 550
500VAC/400VDC
3.15A
500VAC/400VDC
5A
LLC resonant converter 45 - 350
Active filter
60 - 550
500VAC/400VDC
8A
2.3
SCR
FR-4
FR-4
LLC resonant converter 45 - 350
Active filter
60 - 150
500VAC/400VDC
16A
4.6
Relay
LLC resonant converter 45 - 350
*1 The value of input current is at ACIN 115V and 100%.
*2 Burst operation at light loading, frequency is change by use condition.
Please contact us about detail.
June 29, 2020
KH-20
相关型号：
©2020 ICPDF网 联系我们和版权申明