DC60S3H-B [CRYDOM]
Transistor Output SSR,;型号: | DC60S3H-B |
厂家: | CRYDOM INC., |
描述: | Transistor Output SSR, 输出元件 光电 |
文件: | 总7页 (文件大小:653K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Panel Mount
Datasheet
DC60 Series
• Ratings from 3A to 7A @ 60 VDC
• Bi-polar transistor output
• AC and DC control
• Epoxy Free Design
• UL Approved, CE Compliant to EN60950-1
• Improved SEMS screw and washer
• Redesigned housing with anti-rotation barriers
For Generation 3 datasheet click here
PRODUCT SELECTION
Control Voltage
3.5-32 VDC
3A
DC60S3
DC60SA3
5A
DC60S5
DC60SA5
7A
DC60S7
DC60SA7
90-280 VAC/VDC
AVAILABLE OPTIONS
Termination
Blank: Screws & clamps
K: Installed standoffs with
screws for PC Board
mounting (1)
Control Voltage
S: 3.5-32 VDC
SA: 90-280 VAC/DC
Output Type
Blank: Normally Open
-B: Normally Closed (for DC control only)
Series
DC60
SA
3
K
H
-B
Rated Load Current
Thermal Pad
3: 3 Amps
5: 5 Amps
7: 7 Amps
Blank: Not Included
H: Included
Required for valid part number
For options only and not required for valid part number
Not all part number conbinations are available.
Contact Crydom Technical Support for information on
the availability of a specific part number.
*
OUTPUT SPECIFICATIONS (2)
Description
Recommeded Operating Voltage [Vdc]
Absolute Maximum Rating [Vdc]
3A
5A
7A
3-48
3-48
3-48
60
60
60
Maximum Off-State Leakage Current @ Rated Voltage [mA]
Maximum Load Current [Adc] (3)
0.1
3
0.1
5
0.1
7
Minimum Load Current [mA]
20
20
20
Maximum Surge Current (10 msec)[Adc]
Maximum On-State Voltage Drop @ Rated Current [Vdc]
Thermal Resistance Junction to Case (Rjc) [°C/W]
Minimum heat sink @ Ambient (for max current= °C/W & Ta)
6
1
2
10
1.2
2
14
1.3
2
5 @ 60°C
5 @ 60°C
5 @ 40°C
(2)
INPUT SPECIFICATIONS
Description
DC Control
AC Control
Control Voltage Range
3.5-32 VDC
-32 VDC
3.5 VDC
1 VDC
2.2 mA
25 mA
1500
90-280 VAC/VDC
Maximum Reverse Voltage
Minimum Turn-On Voltage (4)
Must Turn-Off Voltage (5)
Minimum Input Current (for on-state)
Maximum Input Current
Nominal Input Impedance [Ohms]
Maximum Turn-On Time [msec] (6)
Maximum Turn-Off Time [msec] (7)
-
90 VAC/VDC
10 VAC/VDC
2 mA
5.5 mA
60K
0.1
0.3
10
40
Do not forget to visit us at: www.crydom.com
Copyright © 2016 Crydom Inc. Specifications subject to change without notice.
Panel Mount
Datasheet
GENERAL SPECIFICATIONS (2)
Description
Dielectric Strength, Input/Output/Base (50/60Hz)
Minimum Insulation Resistance (@ 500 VDC)
Parameters
4000 Vrms
109 Ohm
Maximum Capacitance, Input/Output
Ambient Operating Temperature Range
Ambient Storage Temperature Range
Weight (typical)
8 pF
-30 to 80°C
-40 to 125 °C
2.46 oz (70 g)
Housing Material
UL94 V-0
Baseplate Material
Aluminum
Input Terminal Screw Torque Range (in-lb/Nm)
Load Terminal Screw Torque Range (in-lb/Nm)
SSR Mounting Screw Torque Range (in-lb/Nm)
Input/Load Terminal Screw Torque Range (in-lb/Nm) (1)
Humidity
MTBF (Mean Time Between Failures) at 40°C ambient temperature (8)
MTBF (Mean Time Between Failures) at 60°C ambient temperature (8)
13-15 /1.5-1.7
18-20 / 2-2.2
18-20 / 2-2.2
w/”K” option 8-10 / 0.9-1.13
85% non-condensing
21,395,130 hours (2,441 years)
11,545,504 hours (1,317 years)
WIRING DIAGRAM
* Inductive loads must be diode suppresed.
+
+
-
V
*
*
V
Load
+
Load
+
-
Recommended Wire Sizes
Wire Size
(Solid / Stranded)
Wire Pull-Out
Strength (lb)[N]
Terminals
Input
24 AWG (0.2 mm2) / 0.2 [minimum]
2 x 12 AWG (3.3 mm2) / 3.3 [maximum]
20 AWG (0.5 mm2) / 0.518 [minimum]
2 x 10 AWG (5.3 mm2) / 5.3
10 [44.5]
90 [400]
30 [133]
110 [490]
90 [400]
2
2
+1
4
OUTPUT
S O L I D S T AT E R E L AY
+1
OUTPUT
S O L I D S T AT E R E L AY
4
INPUT
INPUT
+3
+3
Output
2 x 8 AWG (8.4 mm2) / 8.4 [maximum]
+
+
V
V
-
-
Input Current vs Input Voltage
Standard Regulated DC Input
25
20
15
10
5
EQUIVALENT CIRCUIT BLOCK DIAGRAMS
DC60 Series DC Control
3
1
+
DC
+DC
Control
Circuit
Trigger
Circuit
0
0
5
10
15
20
25
30
35
DC Input Voltage
-DC
4
3
2
1
-DC
Input Current vs Input Voltage
Standard Regulated AC Input
5
4.5
DC60 Series AC Control
4
3.5
3
AC/DC
+DC
2.5
2
AC/DC
Trigger
Circuit
1.5
1
Converter
0.5
0
AC/DC
4
2
-DC
0
50
100
150
200
250
300
AC Input Voltage
Do not forget to visit us at: www.crydom.com
Copyright © 2016 Crydom Inc. Specifications subject to change without notice.
Panel Mount
Datasheet
MECHANICAL SPECIFICATIONS (1)
Tolerances: 0.02 in / 0.5 mm
All dimensions are in: inches [millimeters]
(1)
Screw Termination
Hex Standoff Termination (“K” Option)
1.1
1.1
0.89
[22.6]
1.04
[26.4]
(2 places)
[27.9]
[27.9]
Mounting
Mounting
Hole/Slot
0.19 [4.9]
DIA.
0.49
[12.4]
0.49
[12.4]
Hole/Slot
0.19 [4.9]
DIA.
2
2
+1
OUTPUT
+1
OUTPUT
S O L I D S T AT E R E L AY
S O L I D S T AT E R E L AY
2.25
[57.3]
2.25
[57.3]
1.88
[47.6]
1.88
[47.6]
1.7
[43.2]
1.7
[43.2]
4
4
INPUT
INPUT
+3
+3
1.0
1.0
0.93
[23.6]
[25.4]
[25.4]
1.75
[44.5]
(4 places)
1.75
[44.5]
1.0
[25.4]
(2 places)
GENERAL NOTES
(1) Option “K” is designed and tested for use with printed circuit boards or ring/fork terminals having a thickness between 0.031 and 0.093 inches (0.79 to 2.36 mm).
(2) All parameters at 25°C unless otherwise specified.
(3) Heat sinking required, see derating curves.
(4) Maximum turn-on voltage for -B, DC control is 1VDC.
(5) Must turn-off voltage for -B, DC control is 3.5VDC.
(6) Turn-on time for -B version is 300µsec.
(7) Turn-off time for -B version is 100µsec.
(8) All parameters at 50% power rating and 100% duty cycle (contact Crydom tech support for detailed report).
(9) For single surge pulse Tc=25°C; Tj=150°C.
For additional information or specific questions, contact Crydom Technical Support.
Do not forget to visit us at: www.crydom.com
Copyright © 2016 Crydom Inc. Specifications subject to change without notice.
Panel Mount
Datasheet
SURGE CURRENT INFORMATION
Single Pulse (9)
DC60Sx3
DC60Sx5
20
20
15
10
5
15
10
5
0
0
0.1
1
10
100
1000
0.1
1
10
100
1000
(msec)
(msec)
Surge Duration
Surge Duration
DC60Sx7
20
15
10
5
0
0.1
1
10
100
1000
(msec)
Surge Duration
THERMAL DERATE INFORMATION
(i) SSR metal base plate acting as heat sink, it must be exposed to free ambient air.
DC60Sx3
DC60Sx5
5°C/W
No Heat Sink(i)
5°C/W
No Heat Sink(i)
3
2.5
2
5
4
3
2
1
0
1.5
1
0.5
0
20
30
40
50
60
70
80
20
30
40
50
60
70
80
Ambient Temperature (ºC)
Ambient Temperature (ºC)
DC60Sx7
5°C/W
No Heat Sink(i)
7
6
5
4
3
2
1
0
20
30
40
50
60
70
80
Ambient Temperature (ºC)
Do not forget to visit us at: www.crydom.com
Copyright © 2016 Crydom Inc. Specifications subject to change without notice.
Panel Mount
Datasheet
AGENCY APPROVALS
EN60950-1: Meets the requirements of sections1.5: 1,7: 2.9: 2.10.5.3: 4.2: 4.5: 4.7:
E116950
ACCESORIES
Recommended Accessories
New Accessories!
Protective Cover & Hardware Kits
Protective Cover
Cover
KS101
Hardware
Kit
Heat Sink
Part No.
Thermal Resistance Lug Terminal Thermal Pad
[ºC/W]
Part number: KS101
Clear plastic cover compatible with all new
S1 designs. Safety covers provide added
protection from electric shock when
installing or checking equipment.
5.0
3.0
2.5
2.0
2.0
1.7
1.5
1.2
1.0
1.0
0.7
0.7
0.5
0.36
0.25
HK1
HK4
HS501DR
TRM1
TRM6
HSP-1
HSP-2
HS301 / HS301DR
HS251
HS201 / HS201DR
HS202 / HS202DR
HS172
Hardware Kit
Part number: HK4
Bag with 2 square brass accessories and 2
screw 8-32 x 5/8 for output. Used to mount
TMR1 lug terminals.
HS151 / HS151DR
HS122 / HS122DR
HS103 / HS103DR
HS101
HS073
HS072
HS053
HS033
HS023
Rev. 060216
Do not forget to visit us at: www.crydom.com
Copyright © 2016 Crydom Inc. Specifications subject to change without notice.
Panel Mount
Datasheet
DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / 危险
HAZARD OF
ELECTRIC
SHOCK,
EXPLOSION,
OR ARC FLASH.
RIESGO DE
DESCARGA
ELECTRICA O
EXPLOSION.
RISQUE DE
GEFAHR EINES
ELEKTRISCHE
N SCHLAGES
ODER EINER
EXPLOSION.
RISCHIO DI
SCOSSA
ELETTRICA O
DELL’ESPLOSIONE.
存在电击、
爆炸或电弧
闪烁危险
DESCHARGE
ELECTRIQUE
OU EXPLOSION
•
在操作此设
备之前请先
关闭电源。
• Eteindre
toutes les
sources
d'énergie de
cet appareil
avant de
travailler
dessus de cet
appareil
• Spenga tutta
l'alimentazione
che fornisce
questa
apparecchiatura
prima di lavorare
a questa
• Desconectar
todos los
suministros de
energia a este
equipo antes
de trabajar
• Disconnect all
power before
installing or
working with
this equipment.
• Stellen Sie
jeglichen
Strom ab, der
dieses Gerät
versorgt, bevor
Sie an dem
若不遵守这些说明,
可能会导致严重的
人身伤害甚至死亡。
con este equipo.
• Verify all
connections
and replace all
covers before
turning on
Gerät Arbeiten
durchführen
apparecchiatura
• Verificar todas
las conexiones
y colocar todas
las tapas antes
de energizer
• Verificare tutti
i collegamenti
e sostituire
tutte le coperture
prima
• Vor dem
Drehen auf
Energie alle
Anschlüsse
überprüfen
und alle
• Vérifier tous
connections, et
remettre tous
couverts en
olace avant de
mettre sous
power.
el equipo.
Failure to follow
these
instructions will
result in death
or serious injury.
dell’accensione
El
Abdeckungen
ersetzen.
L'omissione di
queste istruzioni
provocherà la
morte o
incumplimiento
de estas
instrucciones
puede provocar
la muerte o
lesiones serias.
De non-suivi de
ces instructions
provoquera la
mort ou des
lésions sérieuses
sérieuses.
Unterlassung
dieser
Anweisungen
können zum
Tode oder zu
schweren
lesioni serie
Verletzungen
führen.
WARNING / AVERTISSEMENT / WARNUNG /ADVERTENCIA / AVVERTENZA / 警告
RISQUE DE DOMMAGE MATERIEL ET DE
SURCHAUFFE DU BOITIER
GEFAHR VON MATERIALSCHÄDEN UND
GEHÄUSEERHITZUNG
RISK OF MATERIAL DAMAGE AND HOT
ENCLOSURE
• Les panneaux latéraux du produit peuvent être
chauds. Laisser le produit refroidir avant de le
toucher.
• Respecter les consignes de montage, et
notamment les couples de serrage.
• Ne pas laisser pénétrer de liquide ni de corps
étrangers à l'intérieur du produit.
• Die Seitenwände können heiß sein. Lassen Sie
das Produkt abkühlen, bevor Sie es berühren.
• Beachten Sie die Montageanweisungen,
• Führen Sie keine Flüssigkeiten oder
• The product's side panels may be hot, allow
the product to cool before touching.
• Follow proper mounting instructions including
torque values.
• Do not allow liquids or foreign objects to enter
this product.
Fremdkörper in das Produkt ein.
Le non-respect de cette directive peut entraîner,
des lésions corporelles graves ou des
dommages matériels.
Die Nichtbeachtung dieser Anweisung kann
Körperverletzung oder Materialschäden
zur Folge haben.
Failure to follow these instructions can result in
serious injury, or equipment damage.
RIESGO DE DAÑOS MATERIALES Y DE
SOBRECALENTAMIENTO DE LA UNIDAD
材料损坏和高温外壳的危险性
RISCHIO DI DANNI MATERIALI E D'INVOLUCRO
CALDO
• 产品的一侧面板可能很热,在其冷却前请
不要触碰。
• 遵照正确的安装说明,包括扭矩值。
• 请勿让液体及其他异物进入本产品。
• Los paneles laterales del producto pueden
estar calientes. Esperar que el producto se
enfríe antes de tocarlo.
• Respetar las instrucciones de montaje, y en
particular los pares de apretado.
• I pannelli laterali dell'apparecchio possono
scottare; lasciar quindi raffreddare il prodotto
prima di toccarlo.
• Seguire le istruzioni di montaggio corrette.
• Non far entrare liquidi o oggetti estranei in questo
apparecchio.
• No dejar que penetren líquidos o cuerpos
extraños en el producto.
La mancata osservanza di questa precauzione può
causare gravi rischi per l'incolumità personale o
danni alle apparecchiature.
如不能正确执行这些操作说明,
极有可能造成严重人体伤害或者设备的损坏。
Si no se respetan estas precauciones pueden
producirse graves lesiones, daños materiales.
Do not forget to visit us at: www.crydom.com
Copyright © 2016 Crydom Inc. Specifications subject to change without notice.
Panel Mount
Datasheet
ANNEX - ENVIROMENTAL INFORMATION
The environmental information disclosed in this annex including the EIP Pollution logo are in compliance with People’s Republic of China
Electronic Industry Standard SJ/T11364 – 2006, Marking for Control of Pollution Caused by Electronic Information Products.
Part
Name
Toxic or hazardous Substance and Elements
Lead
(Pb)
Mercury
(Hg)
Cadmium
(Cd)
Hexavalent
Chromium
(Cr (VI))
Polybrominated
biphenyls
(PBB)
Polybrominated
diphenyl ethers
(PBDE)
Semiconductor die
Solder
附件 - 环保信息
此附件所标示的包括电子信息产品污染图标的环保信息符合中华人民共和国电子行业标准 SJ/T11364 - 2006,
电子信息产品污染控制标识要求。
部件
名称
有毒有害物质或元素
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr (VI))
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
半导体芯片
焊接点
50
Do not forget to visit us at: www.crydom.com
Copyright © 2016 Crydom Inc. Specifications subject to change without notice.
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 211
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 211
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 211
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 211
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 211
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 211
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 211
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 211
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 211
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 211
-
VISHAY
©2020 ICPDF网 联系我们和版权申明