PMP4850WPH_技术文档

Control Relays

Datasheet

PMP Series

• Single Phase Proportional Controller

• Output ratings up to 90 Amps at 600 VAC

Proportional Control SSRs

• Selectable operation mode: Phase Angle or Burst Fire control

• Selectable Control Input: 0-5 VDC, 0-10 VDC, 4-20 mA

• 50/60 Hz Adaptive Operational Frequency function

• 4-20 mA input does not require an auxiliary power supply

• LED multifunction status indicator

• Contactor configuration with "Elevator" screw terminals

• cURus, IEC Rated, CE & RoHS Compliant

The PMP Series of micro-controller based Single-Phase

method to be used can be selected on the unit by means of a

selector switch located on top of the SSR.

This selector switch also allows to select the type of analog signal

to be used at the control input. The available input types are: 0- 5

VDC, 0-10 VDC, and 4-20 mA.

PMP Series Proportional SSRs are ideal for lamp dimming and

resistive heating control, among other type of applications

requiring proportional control.

Proportional Control SSRs are designed to offer precise control of

the power delivered to a resistive load in a compact 22.5mm

housing, with ratings from 25 up to 90 Amps at 90 to 600 VAC.

PMP Series solid state relays can vary the output load power

proportionally to an analog control input from 0 to 100%. This can

be achieved by two different methods: Phase Angle control and

Burst Fire control (with Distributive Zero Cross). The control

PRODUCT SELECTION

Output Voltage

90-280 VAC

345-530 VAC

420-600 VAC

25 A

PMP2425W

PMP4825W

PMP6025W

50 A

PMP2450W

PMP4850W

PMP6050W

90 A

PMP2490W

PMP4890W

PMP6090W

AVAILABLE OPTIONS

Operating Voltage

Terminal Layout

W: Contactor Configuration

(elevator screw)

24: 90-280 VAC

48: 345-530 VAC

60: 420-600 VAC

Thermal Pad

Blank: Not Included

H: Included

Series

PMP

24

25

W

P

H

Rated Load Current

Overvoltage Protection (1)

Blank: Not Included

P: Included

25: 25 Amps

50: 50 Amps

90: 90 Amps

Required for valid part number

For options only and not required for valid part number

OUTPUT VOLTAGE SPECIFICATIONS⁽²⁾

Description

Operating Voltage (45-65Hz) [VRMS]

Transient Overvoltage [Vpk] (1)

Maximum Off-State Leakage Current @ Rated Voltage [mA^RMS]

Minimum Off-State dV/dt @ Maximum Rated Voltage [V/μsec]

PMP24xxW

PMP48xxW

PMP60xxW

90-280

600

4

345-530

1200

2.2

420-600

1200

2

500

FDE-07-01 REV. A

Do not forget to visit us at: www.crydom.com

Control Relays

Datasheet

OUTPUT SPECIFICATIONS ⁽²⁾

Description

Load Current, General Use UL508 @ 40°C [ARMS] (3)

Minimum Load Current [mARMS] (4)

25 A

25

100

50 A

50

100

90 A

90

150

Maximum 1 Cycle Surge Current (50/60Hz) [Apk]

Maximum On-State Voltage Drop @ Rated Current [Vrms]

Maximum 1/2 Cycle I² t for Fusing (50/60Hz) [A² sec]

Thermal Resistance Junction to Case (Rjc) [°C/W]

Maximum Power Dissipation @ Rated Current [W]

Recommended Heat Sink for Rated Current @ 40ºC [°C/W]

Minimum Power Factor (at Maximum load)

Phase Angle Control Range [%]

286/300

1.15

409/375

0.49

29

2

716/750

1.15

2563/2343

0.27

58

1

0.7

1290/1350

1.2

8320/7593

0.2

104

0.36

0.7

0 to 100

0 to 20 Cycles

0 to 100

0 to 20 Cycles

0 to 100

0 to 20 Cycles

Burst Fire Distributive Control Time Base Period

POWER SUPPLY SPECIFICATIONS ^(2)(5)(6)

Description

Supply Voltage Range [VDC]

Maximum Supply Current [mA]

Overvoltage Protection

Reverse Polarity Protection

PMP

8-30

30

Limited to 35 VDC for 60 sec

Yes

(2)

INPUT SPECIFICATIONS

Description

Voltage Control

Current Control

Valid Input Voltage [VDC] / Current [mA]

Maximum Allowed Input Voltage [VDC] / Current [mA]

Maximum Reverse Voltage [VDC] /Current [mA]

Pick up Voltage [VDC] / Current [mA]

Dropout Voltage [VDC] / Current [mA]

Nominal Input Impedance [Ohms]

0-10, 0-5

30

4-20

35

-35

4.3

-30

0.4

0.1

28.8k

5 Cycles

1 Cycle

4

230 @ 20 mA

5 Cycles

1 Cycle

Maximum Initialization Time [msec]

Response Time

GENERAL SPECIFICATIONS ⁽²⁾

Description

Dielectric Strength, Input to Output (50/60Hz)

Dielectric Strength, Input/Output to Baseplate (50/60Hz)

Minimum Insulation Resistance (@ 500 VDC)

Maximum Capacitance, Input/Output

Ambient Operating Temperature Range (7)

Ambient Storage Temperature Range (7)

Weight (typical)

Parameters

4000 VRMS

10⁹Ohms

8 pF

-25 to 70 °C

2.6 oz (73 g)

UL94 V-0

Housing Material

Aluminum

Nickel Plating

20-25/2.2-2.8

93% non-condensing

See Status Chart

III

Baseplate Material

Hardware Finish

SSR Mounting Screw Torque Range (in-lb/Nm)

Humidity per IEC 60068-2-78

LED Input Status Indicator

Overvoltage Category

Impulse Withstand Voltage According to IEC 60664-1

Adaptative Operational Frequency Function

6 kV

Yes

Do not forget to visit us at: www.crydom.com

Control Relays

Datasheet

SURGE CURRENT INFORMATION

PMPxx50W

PMPxx25W

300

700

600

500

400

300

200

100

0

250

200

150

100

50

0

0.01

0.1

1

10

0.01

0.1

1

10

(sec)

Surge Duration

PMPxx90W

1400

1200

1000

800

600

400

200

0

Single Pulse (8)

0.01

0.1

1

10

(sec)

Surge Duration

POWER DISSIPATION

90 Amps

50 Amps

25 Amps

120

100

80

60

40

20

0

10

20

30

40

50

60

70

80

90

Load Current (Amps)

THERMAL DERATE INFORMATION⁽⁹⁾

PMPxx25W

PMPxx50W

PMPxx90W

2.0ºC/W

3.0ºC/W

No Heat Sink

1.0ºC/W

1.5ºC/W

2.0ºC/W

3.0ºC/W

0.36ºC/W

0.5ºC/W

1.0ºC/W

2.0ºC/W

120

100

80

60

40

20

0

70

60

50

40

30

20

10

35

30

25

20

15

10

5

0

25

30

35

40

45

50

55

60

65

70

25

30

35

40

45

50

55

60

65

70

25

30

35

40

45

50

55

60

65

70

Ambient Temperature (ºC)

Do not forget to visit us at: www.crydom.com

Control Relays

Datasheet

TRANSFER CHARACTERISTICS

Phase Angle Control, 0-5 VDC Input

Phase Angle Control, 0-10 VDC Input

Phase Angle Control, 4-20 mA Input

100

90

80

70

60

50

40

30

20

10

0

100

90

80

70

60

50

40

30

20

10

0

100

90

80

70

60

50

40

30

20

10

0

4

5

6

7

8

9

10 11 12 13 14 15 16 17 18 19 20

0

0.5

1

1.5

2

2.5

3

3.5

4

4.5

5

0

1

2

3

4

5

6

7

8

9

10

Input Control Voltage (Volts)

Input Control Current (mA)

Burst Fire Control (All Input Options)

100

90

80

70

60

50

40

30

20

10

0

10

20

30

40

50

60

70

80

90 100

Input Control Percent (0-5 V, 0-10 V, 4-20 mA)

INPUT CURRENT VS INPUT VOLTAGE

0-5 VDC Control Supply

0-10 VDC Control Supply

4-20 mA Control Supply

200

180

160

140

120

100

80

60

40

20

0

400

4.40

4.30

4.20

4.10

4.00

3.90

3.80

3.70

3.60

3.50

350

300

250

200

150

100

50

0

2

4

6

8

10

0

1

2

3

4

5

4

6

8

10

12

14

16

18

20

Input Voltage (Volts)

Input Current (mA)

EQUIVALENT CIRCUIT BLOCK DIAGRAM/WIRING DIAGRAM

A

Load

1/L1

Reference

Voltage

V

Trigger

Circuit

Controller

Current

Sensing

Voltage

Regulator

+

V

AC

0-10V (5)

+

-

0-5V

4-20mA

8-30V

+

-

B

Load

Zero

Cross

Detector

2/T1

-

Do not forget to visit us at: www.crydom.com

Control Relays

Datasheet

INSTALLATION INSTRUCTIONS

■

Mounting on Heat Sink

♦ Select adequate heat sink (see thermal derating curves).

♦ Be sure to use a thermal pad or thermal compound (0.006-0.008 in layer thickness recommended) SSR and the selected heat sink.

♦ SSR housing mounting holes have a diameter of 0.341in (8.66mm). Two screws are needed to mount the SSR onto a heat sink (See Fig 1). Mounting screws

are sold separately as HK8 and are suitable for all Crydom heat sinks. Otherwise, recommended screw size is 8-32 (socket) using an allen wrench (9/64 in) for the

installation. Choose screw length considering mounting surface hole depth and SSR baseplate thickness of 0.125 in (3.2 mm).

♦ Before applying full torque tighten down both screws until they contact the baseplate. Then, tighten them to 20 in-lb (2.2 Nm) min.

♦ For optimal thermal performance heat sink fins should be oriented vertically to promote natural convection airflow.

■

Mounting on Panel

♦ Locate the panel section on which the SSR will be mounted. Panel mount surface must provide adequate heat sinking capability,

uncoated, clean, flat (0.004 in/in recommended) and preferably aluminum.

THERM

P

AL

AD

♦ Be sure to use a thermal pad or thermal compound (0.006-0.008 in layer thickness recommended) between the SSR and the panel.

♦ SSR housing mounting slots have a diameter of 0.341 in (8.66 mm). Two screws are needed (not included) to mount the SSR onto a panel.

Mounting screws are sold separately as HK8. Otherwise, recommended screw size is 8-32 (socket) using allen wrench (9/64 in) forthe

installation. Choose screw length considering the mounting surface and that the SSR baseplate thickness is 0.125 in (3.2 mm).

♦ Before applying full torque tighten down both screws until they contact the baseplate. Then, tighten them to 20 in-lb (2.2 Nm) min.

■

Wire input and output as shown in the Wiring Diagram. For recommended wire sizes and terminal torques see TABLE 1

Select operation mode using the parameter selector switch See TABLE 2

TABLE 1. Recommended Torque and Wire Sizes

Max. Screw Torque

[in-lb (Nm)]

Wire Size

Wire Pull-Out

Terminal

Output

(Solid / Stranded)

Strength (lb)[N]

2

2 x 20 AWG (0.75 mm ) [minimum]

25 [111]

80 [355]

90 [400]

2.2 [9.8]

22 [98]

2

18-20 (2.0-2.2)

5 (0.5)

2 x 10 AWG (6 mm )

2

2 x 8 AWG (10 mm ) [maximum]

2

28 AWG (0.09 mm ) [minimum]

Input

2

12 AWG (3.3 mm ) [maximum]

TABLE 2. Operation Mode

Parameter

Selector Switch

Mode

Function

A

B

C

D

E

Phase Angle, 0-5 VDC control

Phase Angle, 0-10 VDC control

Phase Angle, 4-20 mA control

Burst Fire, 0-5 VDC control

Burst Fire, 0-10 VDC control

Burst Fire, 4-20 mA control

C

D

B

E

F

A

MODE

F

Do not forget to visit us at: www.crydom.com

Control Relays

Datasheet

STATUS CHARTS

TABLE 3. LED Status

Status

LED Indicator

SSR Output

OFF

No Mains Voltage (10)

Flashes twice intermittenly

Frequency Out of Range Flashes three times intermittenly

OFF

Error on Selector

Overtemperature (11)

Phase Control

Flashes four times intermittenly

Flashes five times intermittenly

Varying brightness

OFF

ON

Burst Control

Varying pulsing rate

ON

Status Chart

Error on Selector

Operation

Condition

No Mains Voltage (10)

Frequency Out of Range

Overtemperature (11)

Phase Control

Burst Control

Input

SSR Output/

Load Current

...

870ms

LED Indicator

150ms 280ms

Phase Angle Control Operation Mode

AC Supply

25%

50%

75%

Fully On

* Blue parts on waveform represent the output on the load

Do not forget to visit us at: www.crydom.com

Control Relays

Datasheet

Burst Fire Control Operation Mode

AC Supply

ꢀ.%

.±%

7.%

Fully On

* Blue parts on waveforꢃ represent the output on the load

MECHANICAL SPECIFICATIONS

1039

Tolerances: ±±0±ꢀ ꢁn ꢂ ±0. ꢃꢃ

[3.04]

All dꢁꢃensꢁons are ꢁn: ꢁnches [ꢃꢁllꢁꢃeters]

306ꢀ

[9109]

ꢀ08.

[7ꢀ03]

1088

[4708]

±089

[ꢀꢀ0.]

1018

[3±01]

ꢀ0±9

[.301]

Do not forget to visit us at: www.crydom.com

Control Relays

Datasheet

ACCESSORIES

Recommended Accessories

Hardware

Kit

Heat Sink

Part No.

Thermal Resistance Thermal Pad

[ºC/W]

Lug Terminal

TRM0

TRM6

HK8

HSP-7

HS259DR

2.5

0.7

HS073

HS072

HS053

HS033

HS023

0.7

0.5

0.36

0.25

AGENCY APPROVALS, CONFORMANCES AND EMC

Approvals

E116950

Conformances

United States Standard for Industrial Control Equipment - UL 508 and

Canadian Standard Association for Industrial Control Equipment – C22.2 No. 14.

IEC 60068-2-6: Amplitude Range 10-55 Hz, Displacement 0.75 mm

IEC 60068-2-27: Peak Acceleration 15g, Duration 11ms.

Vibration Resistance

Shock Resistance

Electromagnetic Compatibility

Generic

Standard

Immunity Tests

Test Specification Level

Performance

Electrostatic Discharge

IEC 61000-4-2

8kV air discharge

Criterion A

6kV contact discharge

Fast transients (burst)

IEC 61000-4-4

Output

Input

2kV, 5kHz, 100kHz Criterion B

1kV, 5kHz, 100kHz Criterion B

IEC 61000-6-2

Immunity for

Industrial

Surge

1kV Line to Line

2kV Line to Earth Criterion B

Criterion A

500 VDC +/-

Criterion B

Environments

Output

IEC 61000-4-5

Input Power Supply

GENERAL NOTES

(1) “P” option output will self-trigger between 450-600Vpk (for Operating Voltage option 24) or 900-1200Vpk (for Operating Voltage options 48 and 60). Not suitable for

capacitive loads.

(2) All parameters at 25°C unless otherwise speciﬁed.

(3) Heat sinking required, see derating curves. For load currents greater than 50A use conductors with at least 75°C insulation.

(4) If load current is lower than SSR minimum current, connect resistor in parallel to the load to increase current.

(5) Not required for Current control.

(6) Input should be supplied by Class 2 or double insulated power supply.

(7) No freezing or condensation allowed.

(8) For single surge pulse Tc=25°C; Tj=125°C. For AC Output SSRs, AC RMS value of surge current equals the peak value divided by √2 (1.414).

(9) UL approved rating is the one that intersects at 40°C.

(10) This function is disabled when control signal is set at 100%.

(11) This condition can be caused by excessive ambient temperature, an incorrect heat sink or high input voltage. The condition will be cleared once the internal temperature

cools down below 80 °C.

Rev. 092217

ECN 20325

Do not forget to visit us at: www.crydom.com

Control Relays

Datasheet

DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / 危险

HAZARD OF

ELECTRIC

SHOCK,

EXPLOSION,

OR ARC FLASH.

RIESGO DE

DESCARGA

ELECTRICA O

EXPLOSION.

RISQUE DE

GEFAHR EINES

ELEKTRISCHE

N SCHLAGES

ODER EINER

EXPLOSION.

RISCHIO DI

SCOSSA

ELETTRICA O

DELL’ESPLOSIONE.

存在电击、

爆炸或电弧

闪烁危险

DESCHARGE

ELECTRIQUE

OU EXPLOSION

•

在操作此设

备之前请先

关闭电源。

• Eteindre

toutes les

sources

d'énergie de

cet appareil

avant de

travailler

dessus de cet

appareil

• Spenga tutta

l'alimentazione

che fornisce

questa

apparecchiatura

prima di lavorare

a questa

• Desconectar

todos los

suministros de

energia a este

equipo antes

de trabajar

• Disconnect all

power before

installing or

working with

this equipment.

• Stellen Sie

jeglichen

Strom ab, der

dieses Gerät

versorgt, bevor

Sie an dem

若不遵守这些说明，

可能会导致严重的

人身伤害甚至死亡。

con este equipo.

• Verify all

connections

and replace all

covers before

turning on

Gerät Arbeiten

durchführen

apparecchiatura

• Verificar todas

las conexiones

y colocar todas

las tapas antes

de energizer

• Verificare tutti

i collegamenti

e sostituire

tutte le coperture

prima

• Vor dem

Drehen auf

Energie alle

Anschlüsse

überprüfen

und alle

• Vérifier tous

connections, et

remettre tous

couverts en

olace avant de

mettre sous

power.

el equipo.

Failure to follow

these

instructions will

result in death

or serious injury.

dell’accensione

El

Abdeckungen

ersetzen.

L'omissione di

queste istruzioni

provocherà la

morte o

incumplimiento

de estas

instrucciones

puede provocar

la muerte o

lesiones serias.

De non-suivi de

ces instructions

provoquera la

mort ou des

lésions sérieuses

sérieuses.

Unterlassung

dieser

Anweisungen

können zum

Tode oder zu

schweren

lesioni serie

Verletzungen

führen.

WARNING / AVERTISSEMENT / WARNUNG /ADVERTENCIA / AVVERTENZA / 警告

RISQUE DE DOMMAGE MATERIEL ET DE

SURCHAUFFE DU BOITIER

GEFAHR VON MATERIALSCHÄDEN UND

GEHÄUSEERHITZUNG

RISK OF MATERIAL DAMAGE AND HOT

ENCLOSURE

• Les panneaux latéraux du produit peuvent être

chauds. Laisser le produit refroidir avant de le

toucher.

• Respecter les consignes de montage, et

notamment les couples de serrage.

• Ne pas laisser pénétrer de liquide ni de corps

étrangers à l'intérieur du produit.

• Die Seitenwände können heiß sein. Lassen Sie

das Produkt abkühlen, bevor Sie es berühren.

• Beachten Sie die Montageanweisungen,

• Führen Sie keine Flüssigkeiten oder

• The product's side panels may be hot, allow

the product to cool before touching.

• Follow proper mounting instructions including

torque values.

• Do not allow liquids or foreign objects to enter

this product.

Fremdkörper in das Produkt ein.

Le non-respect de cette directive peut entraîner,

des lésions corporelles graves ou des

dommages matériels.

Die Nichtbeachtung dieser Anweisung kann

Körperverletzung oder Materialschäden

zur Folge haben.

Failure to follow these instructions can result in

serious injury, or equipment damage.

RIESGO DE DAÑOS MATERIALES Y DE

SOBRECALENTAMIENTO DE LA UNIDAD

材料损坏和高温外壳的危险性

RISCHIO DI DANNI MATERIALI E D'INVOLUCRO

CALDO

• 产品的一侧面板可能很热，在其冷却前请

不要触碰。

• 遵照正确的安装说明，包括扭矩值。

• 请勿让液体及其他异物进入本产品。

• Los paneles laterales del producto pueden

estar calientes. Esperar que el producto se

enfríe antes de tocarlo.

• Respetar las instrucciones de montaje, y en

particular los pares de apretado.

• I pannelli laterali dell'apparecchio possono

scottare; lasciar quindi raffreddare il prodotto

prima di toccarlo.

• Seguire le istruzioni di montaggio corrette.

• Non far entrare liquidi o oggetti estranei in questo

apparecchio.

• No dejar que penetren líquidos o cuerpos

extraños en el producto.

La mancata osservanza di questa precauzione può

causare gravi rischi per l'incolumità personale o

danni alle apparecchiature.

如不能正确执行这些操作说明，

极有可能造成严重人体伤害或者设备的损坏。

Si no se respetan estas precauciones pueden

producirse graves lesiones, daños materiales.

Do not forget to visit us at: www.crydom.com

Control Relays

Datasheet

ANNEX - ENVIROMENTAL INFORMATION

The environmental information disclosed in this annex including the EIP Pollution logo are in compliance with People’s Republic of China

Electronic Industry Standard SJ/T11364 – 2006, Marking for Control of Pollution Caused by Electronic Information Products.

Part

Name

Toxic or hazardous Substance and Elements

Lead

(Pb)

Mercury

(Hg)

Cadmium

(Cd)

Hexavalent

Chromium

(Cr (VI))

Polybrominated

biphenyls

(PBB)

Polybrominated

diphenyl ethers

(PBDE)

Semiconductor die

Solder

附件 - 环保信息

此附件所标示的包括电子信息产品污染图标的环保信息符合中华人民共和国电子行业标准 SJ/T11364 - 2006,

电子信息产品污染控制标识要求。

部件

名称

有毒有害物质或元素

铅

(Pb)

汞

(Hg)

镉

(Cd)

六价铬

(Cr (VI))

多溴联苯

(PBB)

多溴二苯醚

(PBDE)

半导体芯片

焊接点

50

Do not forget to visit us at: www.crydom.com


型号：	PMP4850WPH
厂家：	CRYDOM INC.,
描述：	RELAY SSR PROP CNTL PNL MNT 50A 输出元件光电
文件：	总10页 (文件大小：1063K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

PMP4850WPH [CRYDOM]

相关型号：

PMP4890W

PMP4890WH

PMP4890WP

PMP4890WPH

PMP5

PMP5.24

PMP5.24-110

PMP5.48

PMP5.48-110

PMP5201G

PMP5201G,115

PMP5201G,135