UPD24TP [CRYDOM]

PCB Mount;


型号：	UPD24TP
厂家：	CRYDOM INC.,
描述：	PCB Mount PC
文件：	总5页 (文件大小：572K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

PCB Mount

DataSheet

UPD24TP Series

• SIP SSR

• 3 Output Channels in one Package with common control input

• Ratings per channel of 15 A @ 280 VAC

• PCB Mount Package or Panel Mount quick connect terminals (F option)

• SCR output for heavy industrial loads

• Zero-crossing (resistive loads) or random-fire (inductive loads) output

• Low Leakage (snubberless) output

PRODUCT SELECTION

Control Voltage

4.5-8 VDC

15 A

UPD2415TP

15 A

UPD2415TP-10

AVAILABLE OPTIONS

Operational Current

15: 15 Amps

Terminals Type

Blank: Pins for PCB Mount

F: Quick Connect Terminals

Series

UPD 24 15

-10

Switching Mode

Operational Voltage

240: 24-280 VAC

Output

TP: Triple Channel

Blank: Zero Voltage Turn-On

-10: Random Turn-On

Required for valid part number

For options only and not required for valid part number

(1)

OUTPUT SPECIFICATIONS

Description

UPD2415TP

UPD2415TP-10

Operating Voltage (47-440Hz) [Vrms]

Maximum Load Current [Arms](3)

Minimum Load Current [mArms]

Transient Overvoltage [Vpk]

24-280

150

600

150

600

Maximum 1 Cycle Surge Current (50/60Hz) [Apk]

Maximum On-State Voltage Drop @ Rated Current [Vpk]

239/250

1.6

239/250

1.4

Thermal Resistance Junction to Case [°C/W]

1.02

285/259

0.1

1.02

285/259

0.1

Maximum I² t for fusing (50/60Hz, 1/2 cycle) [A² sec]

Maximum Off-State Leakage Current @ Rated Voltage [mArms]

Minimum Off-State dv/dt @ Maximum Rated Voltage [V/μsec] (2)

500

Minimum Power Factor (with Maximum Load)

0.5

INPUT SPECIFICATIONS ⁽¹⁾

Description

UPD2415TP

4.5-8 VDC

4.5 VDC

UPD2415TP-10

4.5-8 VDC

4.5 VDC

Control Voltage Range

Must Turn On Voltage

Must Turn Off Voltage

1.0 VDC

1.0 VAC

14 mAdc

100 Ohm

1/2 Cycle

14 mAdc

100 Ohm

0.02

Typical Input Current @ 5 VDC

Nominal Input Impedance

Maximum Turn-On Time [msec]

Maximum Turn-Off Time [msec]

1/2 Cycle

Do not forget to visit us at: www.crydom.com

PCB Mount

DataSheet

GENERAL SPECIFICATIONS⁽¹⁾

Description

Parameters

2500 Vrms

10⁹Ohm

Dielectric Strength, Input/Output/Base (50/60Hz)

Minimum Insulation Resistance (@ 500 VDC)

Maximum Capacitance, Input/Output

Ambient Operating Temperature Range

Ambient Storage Temperature Range

Weight (typical)

8 pF

-40 to 80 °C

-40 to 125 °C

1.53 oz. (43.4g)

GENERAL NOTES

(1) All parameters at 25°C and per section unless otherwise speciﬁed.

(2) Off-state dv/dt test method per EIA/NARM standard RS-443, paragraph 13.11.1

(3) Heat sinking required, see following pages for derating curves.

MECHANICAL SPECIFICATIONS

Tolerances: ±±0±ꢀ ꢁn ꢂ ±0. ꢃꢃ

All dꢁꢃensꢁons are ꢁn: ꢁnches [ꢃꢁllꢁꢃeters]

UPD2415TP

UPD2415TPF

30±8

10..

30±8

ꢀ08±

10±.

±0..

±01.

ASSEMBLED

INMEXICO

ASSEMBLED

IN MEXICO

101ꢀ

Aꢀ

Bꢀ

Cꢀ

±073

±0.±

0ꢀ.± X 0±3ꢀ SQ

±047

±0ꢀ±

FASTON TERMINAL

(6PLACES)

SQ PIN 0±ꢀ. ±0±±.

01±± CENTERS

(ꢀPLACES)

10ꢀ3

(4 PLC’S)

SQ ±0±3ꢀ ±0±±.

(8 PLC'S)

±0.±

1073

±04±

(3 PLC’S)

WIRING DIAGRAM

LOAD

+ DC

INPUT A

LOAD

LOAD CAN BE WIRED IN POSITION A or B

- DC

LOAD

+ DC

INPUT B

LOAD

- DC

LOAD

+ DC

INPUT C

LOAD

- DC

Do not forget to visit us at: www.crydom.com

PCB Mount

DataSheet

THERMAL DERATE INFORMATION

DERATE CURVE: UPD2415TP

1ºC/W

1.5ºC/W

2ºC/W

3ºC/W

5ºC/W

Ambient Temperature (˚C)

AGENCY APPROVALS

Agency Approvals

Designed in accordance with the requirements of IEC 62314

Rev 112614

Do not forget to visit us at: www.crydom.com

PCB Mount

DataSheet

DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / 危险

HAZARD OF

ELECTRIC

SHOCK,

EXPLOSION,

OR ARC FLASH.

RIESGO DE

DESCARGA

ELECTRICA O

EXPLOSION.

RISQUE DE

GEFAHR EINES

ELEKTRISCHE

N SCHLAGES

ODER EINER

EXPLOSION.

RISCHIO DI

SCOSSA

ELETTRICA O

DELL’ESPLOSIONE.

存在电击、

爆炸或电弧

闪烁危险

DESCHARGE

ELECTRIQUE

OU EXPLOSION

•

在操作此设

备之前请先

关闭电源。

• Eteindre

toutes les

sources

d'énergie de

cet appareil

avant de

travailler

dessus de cet

appareil

• Spenga tutta

l'alimentazione

che fornisce

questa

apparecchiatura

prima di lavorare

a questa

• Desconectar

todos los

suministros de

energia a este

equipo antes

de trabajar

• Disconnect all

power before

installing or

working with

this equipment.

• Stellen Sie

jeglichen

Strom ab, der

dieses Gerät

versorgt, bevor

Sie an dem

若不遵守这些说明，

可能会导致严重的

人身伤害甚至死亡。

con este equipo.

• Verify all

connections

and replace all

covers before

turning on

Gerät Arbeiten

durchführen

apparecchiatura

• Verificar todas

las conexiones

y colocar todas

las tapas antes

de energizer

• Verificare tutti

i collegamenti

e sostituire

tutte le coperture

prima

• Vor dem

Drehen auf

Energie alle

Anschlüsse

überprüfen

und alle

• Vérifier tous

connections, et

remettre tous

couverts en

olace avant de

mettre sous

power.

el equipo.

Failure to follow

these

instructions will

result in death

or serious injury.

dell’accensione

Abdeckungen

ersetzen.

L'omissione di

queste istruzioni

provocherà la

morte o

incumplimiento

de estas

instrucciones

puede provocar

la muerte o

lesiones serias.

De non-suivi de

ces instructions

provoquera la

mort ou des

lésions sérieuses

sérieuses.

Unterlassung

dieser

Anweisungen

können zum

Tode oder zu

schweren

lesioni serie

Verletzungen

führen.

WARNING / AVERTISSEMENT / WARNUNG /ADVERTENCIA / AVVERTENZA / 警告

RISQUE DE DOMMAGE MATERIEL ET DE

SURCHAUFFE DU BOITIER

GEFAHR VON MATERIALSCHÄDEN UND

GEHÄUSEERHITZUNG

RISK OF MATERIAL DAMAGE AND HOT

ENCLOSURE

• Les panneaux latéraux du produit peuvent être

chauds. Laisser le produit refroidir avant de le

toucher.

• Respecter les consignes de montage, et

notamment les couples de serrage.

• Ne pas laisser pénétrer de liquide ni de corps

étrangers à l'intérieur du produit.

• Die Seitenwände können heiß sein. Lassen Sie

das Produkt abkühlen, bevor Sie es berühren.

• Beachten Sie die Montageanweisungen,

• Führen Sie keine Flüssigkeiten oder

• The product's side panels may be hot, allow

the product to cool before touching.

• Follow proper mounting instructions including

torque values.

• Do not allow liquids or foreign objects to enter

this product.

Fremdkörper in das Produkt ein.

Le non-respect de cette directive peut entraîner,

des lésions corporelles graves ou des

dommages matériels.

Die Nichtbeachtung dieser Anweisung kann

Körperverletzung oder Materialschäden

zur Folge haben.

Failure to follow these instructions can result in

serious injury, or equipment damage.

RIESGO DE DAÑOS MATERIALES Y DE

SOBRECALENTAMIENTO DE LA UNIDAD

材料损坏和高温外壳的危险性

RISCHIO DI DANNI MATERIALI E D'INVOLUCRO

CALDO

• 产品的一侧面板可能很热，在其冷却前请

不要触碰。

• 遵照正确的安装说明，包括扭矩值。

• 请勿让液体及其他异物进入本产品。

• Los paneles laterales del producto pueden

estar calientes. Esperar que el producto se

enfríe antes de tocarlo.

• Respetar las instrucciones de montaje, y en

particular los pares de apretado.

• I pannelli laterali dell'apparecchio possono

scottare; lasciar quindi raffreddare il prodotto

prima di toccarlo.

• Seguire le istruzioni di montaggio corrette.

• Non far entrare liquidi o oggetti estranei in questo

apparecchio.

• No dejar que penetren líquidos o cuerpos

extraños en el producto.

La mancata osservanza di questa precauzione può

causare gravi rischi per l'incolumità personale o

danni alle apparecchiature.

如不能正确执行这些操作说明，

极有可能造成严重人体伤害或者设备的损坏。

Si no se respetan estas precauciones pueden

producirse graves lesiones, daños materiales.

Do not forget to visit us at: www.crydom.com

PCB Mount

DataSheet

ANNEX - ENVIROMENTAL INFORMATION

The environmental information disclosed in this annex including the EIP Pollution logo are in compliance with People’s Republic of China

Electronic Industry Standard SJ/T11364 – 2006, Marking for Control of Pollution Caused by Electronic Information Products.

Part

Name

Toxic or hazardous Substance and Elements

Lead

(Pb)

Mercury

(Hg)

Cadmium

(Cd)

Hexavalent

Chromium

(Cr (VI))

Polybrominated

biphenyls

(PBB)

Polybrominated

diphenyl ethers

(PBDE)

Semiconductor die

Solder

附件 - 环保信息

此附件所标示的包括电子信息产品污染图标的环保信息符合中华人民共和国电子行业标准 SJ/T11364 - 2006,

电子信息产品污染控制标识要求。

部件

名称

有毒有害物质或元素

铅

(Pb)

汞

(Hg)

镉

(Cd)

六价铬

(Cr (VI))

多溴联苯

(PBB)

多溴二苯醚

(PBDE)

半导体芯片

焊接点

Do not forget to visit us at: www.crydom.com

UPD24TP [CRYDOM]

相关型号：

UPD26401GU-XXX-9JH

UPD26401GU-XXX-9KH

UPD26411GZ-XXX-KJH

UPD26411GZ-XXX-KKH

UPD27128C

UPD27128C-2

UPD27128C-3

UPD27128C-4

UPD27128D-2

UPD2716

UPD2716D

UPD2732D