CCPD-575 [CRYSTEKMICROWAVE]

5Ã7.5 mm SMD, 3.3V, LVPECL;


型号：	CCPD-575
厂家：	CRYSTEK CORPORATION
描述：	5Ã7.5 mm SMD, 3.3V, LVPECL
文件：	总3页 (文件大小：404K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

CCPD-575 Model

5×7.5 mm SMD, 3.3V, LVPECL

Model CCPD-575 has an industry leading phase noise for an

LVPECL oscillator. The noise floor is typically @ -162 dBc/Hz!

This is at least 15 dB lower phase noise than most LVPECL

oscillators on the market today. Close-in phase noise is also

excellent @ -90 dBc/Hz for the 100 MHz variant.

This overall ultra-low phase noise translates to a typical phase

jitter of 85 fS RMS (12 kHz to 20 MHz)

5×7.5mm SMD

Applications:

Digital Video

SONET/SDH/DWDM

Storage Area Networks

Broadband Access

Ethernet, Gigabit Ethernet

Rev: K

Date: 24-Aug-2015

Page 1 of 3

12730 Commonwealth Drive • Fort Myers, Florida 33913

Phone: 239-561-3311 • 800-237-3061

CRYSTEK

CORPORATION

Fax: 239-561-1025 • www.crystek.com

CCPD-575 Model

5×7.5 mm SMD, 3.3V, LVPECL

Frequency Range:

Frequency Stability:

Operating Temperature Range:

Storage Temperature Range:

Input Voltage:

50.000 MHz to 156.250 MHz*

±20ppm

-40°C to +85°C

-45°C to 90°C

3.3V ± 0.3V

*Standard Frequencies

(MHz)

80.000

100.000

125.000

156.250

Input Current:

Output:

80mA Typical, 88mA Max

Differential LVPECL

40/60% Max @ zero crossing point

300 psec Max (20% to 80%)

Symmetry:

Rise/Fall Time:

Logic: Terminated to Vdd-2V into 50 Ω

“0”=1.37 Min, 1.74 Max

“1”=2.05 Min, 2.54 Max

200nSec Max

Output Low Voltage:

Output High Voltage:

Disable Time:

200mSec Max

Enable Time:

85 fsec RMS Typical @ 100 MHz

Phase Jitter: 12kHz~20MHz

Phase Noise: (See Plot Below)

Sub-harmonics:

None

<3ppm 1^styear, <1ppm every year thereafter

Aging:

Part Number Example: CCPD-575X-20-100.000 3.3V, -40/85°C, ±20ppm, 100.000 MHz

100.000 MHz LVPECL 3.3V 156.250 MHz LVPECL 3.3V

Rev: K

Date: 24-Aug-2015

Page 2 of 3

12730 Commonwealth Drive • Fort Myers, Florida 33913

Phone: 239-561-3311 • 800-237-3061

CRYSTEK

CORPORATION

Fax: 239-561-1025 • www.crystek.com

CCPD-575 Model

5×7.5 mm SMD, 3.3V, LVPECL

Mechanical:

Shock: MIL-STD-883, Method 2002, Condition B

Solderability: MIL-STD-883, Method 2003

Vibration: MIL-STD-883, Method 2007, Condition A

Solvent Resistance: MIL-STD-202, Method 215

Resistance to Soldering Heat: MIL-STD-202, Method 210, Condition I or J

Environmental:

Thermal Shock: MIL-STD-883, Method 1011, Condition A

Moisture Resistance: MIL-STD-883, Method 1004

RECOMMENDED REFLOW SOLDERING PROFILE

Ramp-Up

Critical Temperature

3°C/Sec Max.

Zone

260°C

Ramp-Down

6°C/Sec.

217°C

200°C

150°C

Preheat

90 Secs. Max.

180 Secs. Max.

8 Minutes Max.

260°C for

10 Secs. Max.

NOTE: Reflow Profile with 240°C peak also acceptable.

0.295 -0.008 +0.035

(7.50 -0.20 +0.89)

Dimensions inches (mm)

All dimensions are Max unless otherwise specified.

Tristate Function

Function pin 1

Output pin

CCPD-575

Freq

XXXX XX

0.200 ±0.015

(5.08 ±0.38)

Open or N/C

"1" level 2.0V Min

"0" level 0.8V Max

Active

High Z

0.099

(2.50)

Denotes pad 1

XXXX=Date Code XX=Lot Code

SUGGESTED PAD LAYOUT

Connection

Enable/Disable

0.050

(1.27)

via to

ground

0.046

(1.16)

0.01µF

N/C

GND

Output

0.046

(1.16)

0.154

(3.91)

0.058

(1.47)

Comp Output

Vcc

0.071

(1.80)

0.100

(2.54)

0.100

(2.54)

0.200

(5.08)

0.200

(5.08)

Rev: K

Date: 24-Aug-2015

Page 3 of 3

12730 Commonwealth Drive • Fort Myers, Florida 33913

Phone: 239-561-3311 • 800-237-3061

CRYSTEK

CORPORATION

Fax: 239-561-1025 • www.crystek.com