D120505T-1W [CRYSTEKMICROWAVE]
1W, FIXED INPUT, ISOLATED & UNREGULATED TWIN OUTPUT ULTRAMINIATURE SMD PACKAGE DC-DC CONVERTER; 1W,定电压输入,隔离非稳压双输出超小型SMD封装DC-DC转换器型号: | D120505T-1W |
厂家: | CRYSTEK CORPORATION |
描述: | 1W, FIXED INPUT, ISOLATED & UNREGULATED TWIN OUTPUT ULTRAMINIATURE SMD PACKAGE DC-DC CONVERTER |
文件: | 总3页 (文件大小:292K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
D_T-1W Series
1W, FIXED INPUT, ISOLATED & UNREGULATED
TWIN OUTPUT ULTRAMINIATURE SMD PACKAGE
DC-DC CONVERTER
RoHS
FEATURES
SELECTION GUIDE
● Efficiency up to 80%
● Twin Independent Output
● Small Footprint
● SMD Package Styles
● Industry Standard Pinout
● No Heatsink Required
● 1kVDC Isolation
Input
Voltage (VDC)
Nominal Range
Output
Part
Number
Efficiency
(%,Typ.)
Current (mA)
Voltage
(VDC)
Max.
100/100
56/56
Min.
10/10
6/6
D050505T-1W
D050909T-1W *
D051212T-1W
D051515T-1W *
D120505T-1W *
D120909T-1W *
D121212T-1W
D121515T-1W
*Designing.
5/5
9/9
70
75
79
80
72
75
78
80
5
4.5-5.5
12/12
15/15
5/5
42/42
4/4
● High Power Density
33/33
3/3
● Temperature Range: -40°C ~ +85°C
● No External Component Required
● Internal SMD construction
● RoHS Compliance
100/100
56/56
10/10
6/6
9/9
12
10.8-13.2
12/12
15/15
42/42
4/4
33/33
3/3
Note: The D_T-W2/W5 series also are available in our company.
APPLICATIONS
The D_T-1W series are specially designed for
applications where a group of polar power
supplies are isolated from the input power
supply in a distributed power supply system on
a circuit board. These products apply to:
1) Where the voltage of the input power
supply is fixed (voltage variation ≤±10%);
2) Where isolation is necessary between input
and output (isolation voltage ≤1000VDC);
3) Where the regulation of the output voltage
and the output ripple and noise are not
demanding.
COMMON SPECIFICATIONS
Item
Test condition
Min.
Typ.
Max.
Unit
%
Storage humidity
Operating temperature
Storage temperature
Temp. rise at full load
Lead temperature
Short circuit protection*
Cooling
95
85
-40
-55
125
25
°C
15
1.5mm from case for 10 seconds
300
1
s
Free air convection
Epoxy Resin (UL94-V0)
3500 K hours
package material
MTBF
Such as: purely digital circuits, ordinary low
frequency analog circuits and IGBT power
device driven circuits, etc.
Weight
2.1
g
*Supply voltage must be discontinued at the end of short circuit duration.
PART NUMBER SYSTEM
D050505T-1W
ISOLATION SPECIFICATIONS
Rated Power
Item
Test condition
Min.
Typ.
Max.
Unit
Package Style
Isolation voltage
(Vin/Vout)
Isolation voltage
(Vo1/Vo2)
Isolation resistance
(Vin/Vout)
Isolation resistance
(Vo1/Vo2)
Isolation capacitance
(Vin/Vout)
Isolation capacitance
(Vo1/Vo2)
The 2nd Output Voltage
The 1st Output Voltage
Input Voltage
Tested for 1 minute and 1mA max
1000
VDC
Tested for 1 minute and 1mA max
Test at 500VDC
1000
1000
1000
Product Series
MΩ
Test at 500VDC
MORNSUN Science & Technology Co.,Ltd.
Address: No. 5, Kehui St. 1, Kehui development
center, Science Ave., Guangzhou Science City,
Luogang district, Guangzhou,P.R.China.
Tel: 86-20-28203030
60
60
pF
Fax:86-20-38601272
Http://www.mornsun-power.com
The copyright and authority for the interpretation of the products are reserved by MORNSUN
Specifications subject to change without notice.
D_T-1W B/1-2012 Page 1 of 3
OUTPUT SPECIFICATIONS
APPLICATION NOTE
Item
Test Conditions
Min.
0.1
Typ. Max.
Unit
W
Output power
Line regulation
1
For Vin change of ±1%
±1.2
10% to 100% load(5V output)
10% to 100% load(9V output)
10% to 100% load(12V output)
10% to 100% load(15V output)
12.8
8.3
15
10
10
10
%
Load regulation
6.8
6.0
Output voltage accuracy
Temperature drift
See tolerance envelope graph
100% full load
±0.03 %/°C
Ripple & Noise*
20MHz Bandwidth
50
75
mVp-p
KHz
Switching frequency
Full load, nominal input
100
*Test ripple and noise by “parallel cable” method. See detailed operation instructions at Testing of
Power Converter section, application notes.
Operating Temp.(oC)
RECOMMENDED REFLOW SOLDERING PROFILE
RECOMMENDED CIRCUIT
260oC
250
200
10 Sec Max
220o C
L
Vo1
L
C
C
Vin
0V1
Vo2
150
L
C
DC DC
90 Sec Max
GND
(>220oC)
100
0V2
(Figure 1)
50
0
Vo1
Time (sec.)
Vin
REG
0V1
Vo2
Remark: The curve applies only to the hot air reflow soldering
DC DC
GND
TYPICAL CHARECTERISTICS
0V2
Vo1
REG
REG
1) Requirement On Output Load
Vin
0V1
Vo2
To ensure this module can operate efficiently and reliably, a minimum load is specified
for this kind of DC/DC converter in addition to a maximum load (namely full load).
During operation, make sure the specified range of input voltage is not exceeded, the
minimum output load could not be less than 10% of the full load. If the actual output
power is very small, please connect a resistor with proper resistance at the output end
in parallel to increase the load, or use our company’s products with a lower rated output
power (D_T –W2/W5).
DC DC
GND
0V2
(Figure2)
EXTERNAL CAPACITOR TABLE (TABLE 1)
Vin
(VDC)
Cin
(µF)
Vout
(VDC)
Cout
(µF)
2) Recommended testing circuit
If you want to further decrease the input/output ripple, an “LC” filtering network may
be connected to the input and output ends of the DC/DC converter, see (Figure1).
It should also be noted that the inductance and the frequency of the “LC” filtering
network should be staggered with the DC/DC frequency to avoid mutual interference.
However, the capacitance of the output filter capacitor must be proper. If the
capacitance is too big, a startup problem might arise. For every channel of output,
provided the safe and reliable operation is ensured, the greatest capacitance of its filter
capacitor sees (Table 1).
5
12
-
4.7
2.2
-
5
9
4.7
2.2
1
12
15
-
-
0.47
It’s not recommended to connect any external
capacitor in the application field with less than 0.5 watt
output.
3) Output Voltage Regulation and Over-voltage Protection Circuit
The simplest device for output voltage regulation, over-voltage and over-current
protection is a linear voltage regulator with overheat protection that is connected to the
input or output end in series (Figure2).
4) Overload Protection
Under normal operating conditions, the output circuit of these products has no
protection against overload. The simplest method is to connect a self-recovery fuse in
series at the input end or add a circuit breaker to the circuit.
5) Cannot use in parallel and hot swap
The copyright and authority for the interpretation of the products are reserved by MORNSUN
Specifications subject to change without notice.
D_T-1W
B/1-2012
Page 2 of 3
OUTLINE DIMENSIONS& RECOMMENDED FOOTPRINT
MECHANICAL DIMENSIONS
RECOMMENDED FOOTPRINT
17.78 [0.700]
15.24 [0.600]
14 13 12
10
9
8
7
14 13 12
10
9
6
8
7
(Top View)
3
6
1 2
5
1
2
3
5
2.10 [0.083]
0.60 [0.024]
2.54 [0.100]
1.00 [0.039]
(Front View )
Note: grid 2.54*2.54mm.
FOOTPRINT DETAILS
5.75 [0.226]
6.00 [0.236]
A
Pin
Function
GND
12.22 [0.481]
1
0.25 [0.010]
Vin
2
5
0V1
Vo1
Vo2
0V2
A
6
9
5 max
1.30 [0.051]
10
Others
NC
Note:
Unit: mm[inch]
Pin section tolerances: 0.10mm[ 0.004inch
NC:No Connection
±
±
]
General tolerances: ±0.25mm[±0.010inch]
TUBE OUTLINE DIMENSIONS
REEL PACKING OUTLINE DIMENSIONS
Taping dimension:
4.00 [0.157]
18.00[0.709]
2.00 [0.079]
1.75 [0.069]
14.20[0.559]
∅1.50[0.059]
∅1.50[0.059]
0.50[0.020]
21.50 [0.846]
14.30 [0.563]
8.00 [0.315]
9.80 [0.386]
7.60 [0.299]
8.30 [0.327]
6.80[0.268]
37.40 [1.472]
24.00 [0.945]
Taping reel dimension:
Note:
Unit: mm[inch]
∅100.00 [3.937]
±
±
0.50mm[ 0.020inch]
General tolerances:
L=530mm[20.866inch] Devices per tube quantity: 28pcs
L=220mm[8.661inch] Devices per tube quantity: 10pcs
Short tube inner package dimensions: L*W*H= 255*170*80mm
Short tube outer package dimensions(with six inner package boxes):
L*W*H= 375*280*270mm
Long tube inner package dimensions: L*W*H= 580*200*100mm
Long tube outer package dimensions(with two inner package boxes):
L*W*H= 600*215*220mm
Long tube outer package dimensions(with three inner package boxes):
L*W*H= 600*215*325mm
∅13.00 [0.512]
∅21.50 [0.846]
Note:
Unit:mm[inch]
General tolerances: ±0.50mm[±0.020inch]
Per reel of packing quantity:400pcs
Innerpackage cartondimensions:L*W*H=365*350*105mm
Tube Quantity:800pcs
Outerpackagecartondimensions:L*W*H=390*360*245mm
Tube Quantity:1600pcs
Note:
1. Operation under minimum load will not damage the converter; However, they may not meet all specification listed, and that will reduce the life
of product.
2. All specifications measured at Ta=25°C, humidity<75%, nominal input voltage and rated output load unless otherwise specified.
3. Only typical models listed, other models may be different, please contact our technical person for more details.
4. In this datasheet, all the test methods of indications are based on corporate standards.
The copyright and authority for the interpretation of the products are reserved by MORNSUN
Specifications subject to change without notice.
D_T-1W B/1-2012 Page 3 of 3
相关型号:
©2020 ICPDF网 联系我们和版权申明