IB1212LT-1W [CRYSTEKMICROWAVE]
1W, FIXED INPUT, ISOLATED & REGULATED SINGLE OUTPUT SMD DC-DC CONVERTER; 1W,定电压输入,隔离稳压单输出系列的DC -DC转换器型号: | IB1212LT-1W |
厂家: | CRYSTEK CORPORATION |
描述: | 1W, FIXED INPUT, ISOLATED & REGULATED SINGLE OUTPUT SMD DC-DC CONVERTER |
文件: | 总3页 (文件大小:304K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
IB_LT-1W Series
1W, FIXED INPUT, ISOLATED & REGULATED
SINGLE OUTPUT SMD DC-DC CONVERTER
RoHS
FEATURES
PRODUCT PROGRAM
● Small Footprint
Input
Output
Part
Number
Efficiency
(%, Typ.)
● SMD Package
● 1kVDC Isolation
Voltage (VDC)
Current (mA)
Voltage
(VDC)
Nominal
Range
Max.
150
111
83
Min.
15
12
9
● Temperature Range: -40°C ~ +85°C
● Internal SMD Construction
● Short Circuit Protection
● No Heatsink Required
● No External Component Required
● Industry Standard Pinout
● RoHS Compliance
IB0505LT-W75
IB0509LT-1W
IB0512LT-1W
IB0515LT-1W
IB1205LT-W75
IB1212LT-1W
IB1215LT-1W
IB1505LT-W75 *
IB1509LT-1W *
IB1512LT-1W *
IB1515LT-1W
IB2405LT-W75
IB2409LT-1W *
IB2412LT-1W
IB2415LT-1W
*Designing
5
9
69
70
71
72
69
71
72
69
70
71
72
69
70
71
72
5
4.75-5.25
12
15
5
67
7
150
83
15
9
12
15
11.4-12.6
12
15
5
67
7
150
111
83
15
12
9
9
14.25-15.75
APPLICATIONS
The IB_LT-1W series are specially designed for
applications where a group of polar power supplies
12
15
5
67
7
150
111
83
15
12
9
are isolated from the input power supply in
a
distributed power supply system on a circuit board.
These products apply to:
9
24
22.8-25.2
12
15
1) Where the voltage of the input power supply
is fixed (voltage variation ≤ ±5%);
67
7
2) Where isolation is necessary between input
and output (isolation voltage ≤1000VDC);
3) Where the regulation of the output voltage and
the output ripple noise are not demanding.
COMMON SPECIFICATIONS
Item
Test Conditions
Min.
Typ.
Max.
Units
%
Storage humidity
Operating temperature
Storage temperature
Temp. rise at full load
Lead temperature
Cooling
95
85
-40
-55
125
25
°C
15
MODEL SELECTION
1.5mm from case for 10 seconds
260
IB0512LT-1W
Free air convection
Continuous
Rated Power
Package Style
Output Voltage
Input Voltage
Produc t Series
Short circuit protection
Package material
MTBF
Epoxy Resin (UL94-V0)
3500 k hours
Weight
2.9
Typ.
70
g
ISOLATION SPECIFICATIONS
MORNSUN Science & Technology Co.,Ltd.
Address: No. 5, Kehui St. 1, Kehui development
center, Science Ave., Guangzhou Science City,
Luogang district, Guangzhou,P.R.China.
Tel: 86-20-28203030
Item
Test Conditions
Tested for 1 minute and 1mA max 1000
Test at 500VDC 1000
Min.
Max.
Units
VDC
MΩ
Isolation voltage
Isolation resistance
Isolation capacitance
pF
Fax:86-20-38601272
Http://www.mornsun-power.com
The copyright and authority for the interpretation of the products are reserved by MORNSUN
Specifications subject to change without notice.
IB_LT-1W B/1-2010 Page 1 of 3
OUTPUT SPECIFICATIONS
TYPICAL CHARACTERISTICS
Item
Test Conditions
Min.
0.1
Typ. Max. Units
Output power
Line regulation
Load regulation
1
W
For Vin change of ±5%
±0.3
±1
%
10% to 100% load
Output voltage accuracy 100% full load
±3
Temperature drift
Ripple*
100% full load
±0.03 %/°C
20MHz Bandwidth
20MHz Bandwidth
Full load, nominal input
10
50
20
mVp-p
150
Noise*
Switching frequency
100
kHz
*Test ripple and noise by “parallel cable” method. See detailed operation instructions at Testing of Power
Converter section, application notes.
Operating Temp.(oC)
RECOMMENDED REFLOW SOLDERING PROFILE
RECOMMENDED CIRCUIT
Peak.Temp 260
C
2 50
10 Sec Max
L
220
C
L
2 00
1 50
1 00
+Vo
0V
Vin
Cout
Cin
DC
DC
GND
90 Sec Max
C
(>220
)
(Figure 1)
50
0
Time (sec.)
+Vo
0V
Vin
GND
REG
DC DC
APPLICATION NOTE
1) Requirement on output load
(Figure 2)
To ensure this module can operate efficiently and reliably, During operation, the minimum
output load could not be less than 10% of the full load. If the actual output power is very
small, please connect a resistor with proper resistance at the output end in parallel to
increase the load
EXTERNAL CAPACITOR TABLE (TABLE 1)
Vin
(VDC)
Cin
(µF)
Single Vout
(VDC)
Cout
(µF)
2) Recommended circuit
5
4.7
2.2
1
5
9
4.7
2.2
2.2
1
If you want to further decrease the input/output ripple, an “LC” filtering network may be
connected to the input and output ends of the DC/DC converter, see (Figure 1).
It should also be noted that the inductance and the frequency of the “LC” filtering network
should be staggered with the DC/DC frequency to avoid mutual interference. However, the
capacitance of the output filter capacitor must be proper. If the capacitance is too big, a
startup problem might arise. For every channel of output, provided the safe and reliable
operation is ensured, the greatest capacitance of its filter capacitor sees (Table 1).
12
15
24
12
15
1
It’s not recommended to connect any external
capacitor in the application field with less than 0.5
watt output.
3) Overload Protection
Under normal operating conditions, the output circuit of these products has no protection
against over-current. The simplest method is to connect a self-recovery fuse in series at the
input end or add a circuit breaker to the circuit.
4) Input Over-voltage Protection Circuit
The simplest device for input over-voltage protection is a linear voltage regulator with
overheat protection that is connected to the input end in series (Figure 2).
5) No parallel connection or plug and play
The copyright and authority for the interpretation of the products are reserved by MORNSUN
Specifications subject to change without notice.
IB_LT-1W
B/1-2010
Page 2 of 3
OUTLINE DIMENSIONS & PIN CONNECTIONS
MECHANICAL DIMENSIONS
RECOMMENDED FOOTPRINT
(Side View)
5.75 [0.226]
6.00 [0.236]
17.78 [0.700]
15.24 [0.600]
14 13 12
10
9
8
7
2.54 [0.100]
2.10 [0.083]
14 13 12
10
9
8
7
1
2
3
5
6
(Top View)
1.00 [0.039]
2.54 [0.100]
1 2
3
5
6
0.60 [0.024]
2.54 [0.100]
A
FOOTPRINT DETAILS
Pin
Function
GND
12.22 [0.481]
1
0.25 [0.010]
2
Vin
6
7
0V
+Vo
A
5 max
Others
NC
Note:
Unit: mm[inch]
1.30 [0.051]
NC:No Connection
Pin section tolerances: 0.10mm[ 0.004inch]
General tolerances: 0.25mm[ 0.010inch]
REEL PACKING OUTLINE DIMENSIONS
TUBE OUTLINE DIMENSIONS
Taping dimension:
4.00 [0.157]
18.00[0.709]
2.00 [0.079]
1.75 [0.069]
14.20[0.559]
∅1.50[0.059]
∅1.50[0.059]
0.50[0.020]
21.20 [0.835]
14.00 [0.551]
7.10 [0.280]
6.80[0.268]
7.30 [0.287]
24.00[0.945]
0.60 [0.024]
37.40 [1.472]
Taping reel dimension:
8.60 [0.339]
∅100.00 [3.937]
Note:
Unit: mm[inch]
General tolerances: 0.5mm[ 0.020inch]
L=530mm[20.866inch] Devices per tube quantity: 28pcs
L=220mm[8.661inch] Devices per tube quantity: 10pcs
∅13.00 [0.512]
∅21.50 [0.846]
Note:
Unit: mm[inch]
General tolerances: 0.5mm[ 0.020inch]
Devices per reel quantity: 400pcs
Note:
1. Operation under minimum load will not damage the converter; However, they may not meet all specification listed, and that will reduce the life
of product.
2. All specifications measured at Ta=25°C, humidity<75%, nominal input voltage and rated output load unless otherwise specified.
3. Only typical models listed, other models may be different, please contact our technical person for more details.
4. In this datasheet, all the test methods of indications are based on corporate standards.
The copyright and authority for the interpretation of the products are reserved by MORNSUN
Specifications subject to change without notice.
IB_LT-1W B/1-2010 Page 3 of 3
相关型号:
©2020 ICPDF网 联系我们和版权申明