H2023-175.0MG [CTS]
Oscillator,;FULL SIZE D.I.L.
M package
M2001 thru M2007
M2021 thru M2023
M2031 thru M2033
VOLTAGE CONTROLLED
CRYSTAL OSCILLATORS
HCMOS 5V
HALF SIZE D.I.L.
H package
H2001 thru H2007
H2021 thru H2023
H2031 thru H2033
Thru-Hole / Gull Wing
0º to 70ºC
1 MHz to 175 MHz
These 5V VCXOs generate an HCMOS frequency output which is
controlled by an input voltage. The end-point frequency/voltage
parameters are defined, as is the center frequency.
Description
Thru-hole VCXOs are available for 5V
operation from 1 MHz to175 MHz. Users
have a choice of many off-the-shelf models.
Diverse combinations of pull, control volt-
age and center frequency deviation are
available, accommodating a wide variety
of filtering and driving circuitry. Standard
VCXOs are hermetically sealed in full size
(M) or half size (H), DIL packages. All
VCXOs are tested and guaranteed over
0 to 70°C. For operation from -40 to +85°C
see our extended temperature models.
GUARANTEED CAPTURE RANGE/ABSOLUTE PULL RANGE
Guaranteed Capture Range (GCR) and Absolute Pull Range (APR) are terms often used interchangeably.
MF's Guaranteed Capture Range (GCR) is defined as the minimum guaranteed frequency deviation or
"pull" (in ppm) around the nominal frequency, with all effects of temperature, variations in V , variations
DD
in load, and aging taken into account. This amount of absolute frequency deviation is available under all
operating conditions for modulation or capturing other signals. No additional frequency capture
allowances are necessary.
FEATURES
• Frequency from 1 MHz to 175 MHz
• Capture-range is fully defined, under all conditions
• Start-up time less than 5 ms
• Low profile package available above 60 MHz
• Choice of thru-hole or gull wing
CONNECTIONS
Full
Size
Half
Size
TYPICAL APPLICATIONS
• Phase locked loops and data acquisition projects, including:
– xDSL customer premise equipment
– Cable modems
Pin 1. Pin 1. Control Voltage, VC
Pin 7. Pin 4. Ground & Case
Pin 8. Pin 5. Output
– ATM/SONET/SDH
Pin 14. Pin 8. +5V, VDD
DOT
DENOTES
PIN 1
DOT
DENOTES
PIN 1
DOT
DENOTES
PIN 1
DOT
DENOTES
PIN 1
.800 – .005
.060 TYP
.800 – .005
.52 MAX
SQUARE
.52 MAX
SQUARE
.200 MAX
.215 MAX
.200 MAX
.270 MAX
.2 MAX
.160
.2
MAX
.200 MAX
.070
.008/025 .15 MIN
.018 – .001
Pin 1
.018 – .001
.018
.300 – .005
.018
.300
.400
.300
+.004
.600 – .005
.600 – .005
.100 – .005
Pin 7
Pin 1
Pin 7
4
5
8
1
4
5
.520 – .005
.300 –. 005
.300
.500 – .005
.300
+.004
.300 –. 005
.150
8
1
.250 MAX
Pin 14
Pin 14
Pin 8
Pin 8
Glass Insulators (4)
GLASS INSULATORS (4)
GLASS INSULATORS (4)
on .48 x .18 ctrs.
“M” Package
“H” Package
“M” Package
with Gull Wing
“H” Package
with Gull Wing
ELECTRONICS
10 Commerce Dr
• New Rochelle NY 10801
+
International Sales: 1.914-712-2200 • USA Sales: +1.800.331.1236 • Fax: 914.712.2290 • www.mfelectronics.com • email:sales@mfelectronics.com
1 of 4
FULL SIZE D.I.L.
M package
M2001 thru M2007
M2021 thru M2023
M2031 thru M2033
VOLTAGE CONTROLLED
CRYSTAL OSCILLATORS
HCMOS 5V
Thru-Hole / Gull Wing,
0º to 70ºC
HALF SIZE D.I.L.
H package
H2001 thru H2007
H2021 thru H2023
H2031 thru H2033
1 MHz to 175 MHz
DESCRIPTIONS
Center Frequency is Between Two Voltages
Guaranteed
Capture
Range
(ppm)
Control
Center
Frequency
Stability
(ppm)
M2001, H2001
±175 ppm, min. deviation
Control
Voltage
(Volts)
Frequency
Deviation
(ppm)
Voltage
at Center
Frequency
when using 0.3 to 10V control-voltage
MODEL
M2002, H2002
M2003, H2003
M2004, H2004
M2005, H2005
±75 ppm, min. deviation
when using 0.3 to 4.0V control-voltage
2001
2002
2003
2004
2005
2006
2007
0.3 to 10.0
0.3 to 4.0
0.3 to 10.0
0.3 to 4.0
1.0 to 4.0
0 to 5.0
± 175 min
± 75 min
± 175
± 75
2.5 to 5.0
1.3 to 2.3
2.5 to 5.0
1.3 to 2.3
1.8 to 3.0
—
±175 ppm to ±300 ppm deviation when using
0.3 to 10V control-voltage
± 175 to 300
± 125 min
± 75 to 300
± 150 min
± 125 to 250
± 175
± 125
± 75
± 30, typ
±125 ppm min. deviation
± 50, max
when using 0.3 to 4.0V control-voltage
± 150
± 125
±75 ppm to ±300 ppm deviation when using
1.0 to 4.0V control-voltage, for use where the
control voltage is 1 volt off both rails
0.5 to 4.5
1.8 to 3
M2006, H2006
M2007, H2007
M2021, H2021
M2022, H2022
M2023, H2023
M2031, H2031
M2032, H2032
M2033, H2033
±150 ppm, min. deviation when using
0 to 5.0V rail-to-rail control-voltage
Center Frequency is at 2.5V with ±50 ppm stability
±125 ppm to ±250 ppm deviation when using
0.5 to 4.5V control-voltage
Guaranteed
Capture
Range
Control
Voltage
at Center
Frequency
Center
Frequency
Stability
(ppm)
Control
Voltage
(Volts)
Frequency
Deviation
(ppm)
MODEL
±75 ppm capture when using using 0.5 to 4.5V
(ppm)
control-voltage and 2.5V center with ±50 ppm stability
2021
2022
2023
0.5 to 4.5
0.5 to 4.5
0.5 to 4.5
± 75 to 150
± 100 to 200
± 150 to 300
± 75
2.5
2.5
2.5
±100 ppm capture when using using 0.5 to 4.5V
± 30, typ
± 100
± 150
control-voltage and 2.5V center with ±50 ppm stability
± 50, max
±150 ppm capture when using using 0.5 to 4.5V
control-voltage and 2.5V center with ±50 ppm stability
±75 ppm capture when using using 0.5 to 4.5V
Center Frequency is at 2.5V with ±25 ppm stability
control-voltage and 2.5V center with ±25 ppm stability
Guaranteed
Capture
Range
Control
Voltage
at Center
Frequency
Center
Frequency
Stability
(ppm)
±100 ppm capture when using using 0.5 to 4.5V
Control
Voltage
(Volts)
Frequency
Deviation
(ppm)
control-voltage and 2.5V center with ±25 ppm stability
MODEL
±150 ppm capture when using using 0.5 to 4.5V
(ppm)
control-voltage and 2.5V center with ±25 ppm stability
2031
2032
2033
0.5 to 4.5
0.5 to 4.5
0.5 to 4.5
± 75 to 150
± 100 to 200
± 150 to 300
± 75
2.5
2.5
2.5
± 20, typ
± 100
± 150
± 25, max
FREQUENCY STABILITY
Frequency stability vs. Temperature (0 to 70°C) is typically better than
±20 ppm. Since the deviation of each oscillator is tested and guaranteed
over the whole operating temperature range, it is not necessary to make
additional capture allowance. All oscillators will capture frequencies with
the full minimum values of the deviation under all conditions.
PIN 1.
CONTROL VOLTAGE
FET PROBE
V
QUALITY
DD
Y-OUTPUT
350 MHz
SCOPE
+5V
Each VCXO is computer-tested at three temperatures to guarantee
full compliance to the specification.
MA
1
14
(8)
Power
Supply
(1)
LOAD
COUNTER
7
8
GND
(4)
(5)
Half Size connections shown in (
)
To adapt Fet probe to receptacle
use Tektronix Part #103-0164-00
To connect output to scope use
use Tektronix Part #131-0258-00 (receptacle)
ALL OSCILLATORS HAVE INTERNAL BYPASS CAPACITORS
TEST CIRCUIT
ELECTRONICS
10 Commerce Dr
• New Rochelle NY 10801
+
International Sales: 1.914-712-2200 • USA Sales: +1.800.331.1236 • Fax: 914.712.2290 • www.mfelectronics.com • email:sales@mfelectronics.com
2 of 4
FULL SIZE D.I.L.
M package
M2001 thru M2007
M2021 thru M2023
M2031 thru M2033
VOLTAGE CONTROLLED
CRYSTAL OSCILLATORS
HCMOS 5V
Thru-Hole / Gull Wing,
0º to 70ºC
HALF SIZE D.I.L.
H package
1 MHz to 175 MHz
H2001 thru H2007
H2021 thru H2023
H2031 thru H2033
ELECTRICAL SPECIFICATIONS
MECHANICAL SPECIFICATIONS
Frequency Range 1 MHz to 175 MHz
Gross Leak – Each unit checked in 125°C fluorocarbon
-8
Frequency Stability Includes calibration at 25°C, operating temperature,
change of input voltage, change of load, shock and
vibration.
Fine Leak – Mass spectrometer leak rate less than 2 X 10 atmos,
cc/sec of helium
Pins – Kovar, nickel plated with 60/40 solder coat
Bend Test – Will withstand two bends of 90° from reference
Header – Steel, with nickel plate
Center Frequency Range
VC = 2.5V
1 MHz to 175 MHz
Frequency Stability
VC = 2.5V
±20, ±25 or ±50 ppm, max.
Case – Stainless steel, type 304
as shown in model specification
Marking – Permanent black epoxy ink or laser marked
Resistance to Solvents – MIL STD 202, Method 215
MIN
TYP
5.0
30
MAX UNITS
Input Voltage
Input Current
4.5
5.5
45
volts
mA
Output Levels (HCMOS)
“0” Level, sinking 16 mA.
“1” Level, sourcing 10 mA.
0.4
volts
volts
VDD -.4
Rise and Fall Times, HCMOS
From 0.4 to (VDD-.4) V
(Above 35 MHz)
2.5
4
2
ns
ns
Symmetry
At VDD/ 2
45/55 percent
Aging
First year
After first year
3
1
ppm
ppm/yr
Input Impedance,
Pin 5., Control Voltage
15
15
1000
150
Kohms
KHz
Control Voltage Bandw idth
ENVIRONMENTAL SPECIFICATIONS
Temperature
Operating
Storage
0º to 70°C
-55º to +125°C
Fig. 1 M2001 -27M
with 33 pf load
Temperature Cycle – Not to exceed ±5 ppm change when exposed to 2
hours maximum at each temperature from 0 to 120°C, with 25°C reference
Shock – 1000 Gs, 0.35 ms, 1/2 sine wave, 3 shocks in each plane
Vibration – 10-2000 Hz of .06" d.a. or 20 Gs, whichever is less
Humidity – Resistant to 85° R.H. at 85°C
ELECTRONICS
10 Commerce Dr
• New Rochelle NY 10801
+
International Sales: 1.914-712-2200 • USA Sales: +1.800.331.1236 • Fax: 914.712.2290 • www.mfelectronics.com • email:sales@mfelectronics.com
3 of 4
FULL SIZE D.I.L.
M package
M2001 thru M2007
M2021 thru M2023
M2031 thru M2033
VOLTAGE CONTROLLED
CRYSTAL OSCILLATORS
HCMOS 5V
Thru-Hole / Gull Wing,
0º to 70ºC
HALF SIZE D.I.L.
H package
1 MHz to 175 MHz
H2001 thru H2007
H2021 thru H2023
H2031 thru H2033
FREQUENCY VS. CONTROL VOLTAGE
FOR TYPICAL DEVICES
600
500
400
300
200
100
0
200
150
100
50
Vdd = 5.0V
VDD = 5.0V
0
-50
-100
-150
-200
-250
-300
-100
-200
-300
-400
2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0
1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
.3 .5 1.0
0.0 0.5
Control Voltage, V
Control Voltage, Vc
c
Fig. 2 M2001-40M
Fig. 6 M2023 -19.44
250
200
150
100
50
250
200
150
100
50
VDD = 5.0V
0
-50
0
-100
-150
-200
-250
-50
-100
-150
1.3
2.3
4.0
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
0.3
0.5
Control Voltage, V
Control Voltage, V
c
c
Fig. 3 M2002 -12.352
Fig. 4 M2007-16.777216M
HOW TO ORDER
For Part Number, put package type before model number,
and add frequency in MHz, for example:
M 2 0 3 3-1 4 .3 7 2 M
“M” is full size DIL
“H” is half size DIL is model
type
“2033”
“14.372 M”
frequency
in MHz
Leave blank
for straight leads
Add “G” for
gullwing
Unless customer-specific terms and conditions
are signed by an officer of MF Electronics, the
sale of this and all MF Electronics products are
subject to terms and conditions set forth at
www.mfelectronics.com/terms
SS#
Rev.
A
M2001
ELECTRONICS
10 Commerce Dr
• New Rochelle NY 10801
+
International Sales: 1.914-712-2200 • USA Sales: +1.800.331.1236 • Fax: 914.712.2290 • www.mfelectronics.com • email:sales@mfelectronics.com
4 of 4
相关型号:
H202PC
Pushbutton Switch, SPST, Momentary, 0.25A, 120VDC, Solder Terminal, Through Hole-straight,
SWITCH
H203
Pushbutton Switch, SPDT, On-(on), Momentary, 0.25A, 120VDC, Solder Terminal, Panel Mount-threaded,
SWITCH
H203-AP
Zener Diode, 20.65V V(Z), 2.18%, 0.5W, Silicon, Unidirectional, DO-35, ROHS COMPLIANT PACKAGE-2
MCC
H203-BP
Zener Diode, 20.65V V(Z), 2.18%, 0.5W, Silicon, Unidirectional, DO-35, ROHS COMPLIANT PACKAGE-2
MCC
H203-TP
Zener Diode, 20.65V V(Z), 2.18%, 0.5W, Silicon, Unidirectional, DO-35, ROHS COMPLIANT PACKAGE-2
MCC
©2020 ICPDF网 联系我们和版权申明