VLED15-120-1000 [CUI]
LED DRIVER; LED驱动器型号: | VLED15-120-1000 |
厂家: | CUI INC |
描述: | LED DRIVER |
文件: | 总5页 (文件大小:146K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
date 07/18/2012
page 1 of 5
SERIES: VLED15 │ DESCRIPTION: LED DRIVER
FEATURES
• constant current
• high efficiency
• 90~135 Vac and 176~265 Vac input range available
• 0.35~1.5 A output current
• operates with industry standard dimmers
• compact encapsulated assembly
• active power factor correction
• over voltage, over current, over temperature protection max.,
short circuit protection: auto recovery
• high temperature operation (up to 90°C case)
• UL approved, ENEC approved, CE Mark
• long life > 50,000 hours
RoHS
output voltage1
output current
output wattage
efficiency
MODEL
min
max
min
max
max
max
(Vdc)
(Vdc)
(A)
(A)
(W)
(%)
VLED15-120-350
VLED15-120-480
VLED15-120-600
VLED15-120-700
VLED15-120-800
VLED15-120-900
VLED15-120-900L
VLED15-120-1000
VLED15-120-1200
VLED15-120-1250
VLED15-120-14002
VLED15-120-1500
VLED15-230-350
VLED15-230-480
VLED15-230-600
VLED15-230-700
VLED15-230-800
VLED15-230-900
VLED15-230-900L
VLED15-230-1000
VLED15-230-1200
VLED15-230-1250
VLED15-230-14002
VLED15-230-1500
24
10
8
48
13.5
12
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
350
16.8
6.5
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
480
600
7.2
16
8
24
700
16.8
9.6
12
800
10
8
16
900
14.4
10.8
16
12
900
10
10
8
16
1,000
1,200
1,250
1,400
1,500
350
14.1
12
16.92
15
8
11.5
10
16.1
15
5
24
10
8
48
16.8
6.5
13.5
12
480
600
7.2
16
8
24
700
16.8
9.6
12
800
10
8
16
900
14.4
10.8
16
12
900
10
10
8
16
1,000
1,200
1,250
1,400
1,500
14.1
12
16.92
15
8
11.5
10
16.1
15
5
Note:
1. Total LED forward voltage must be within these ratings under all conditions including dimming
2. 80°C maximum case rating
3. Ripple Current: <40% (p-p) of maximum Output Current with no dimming
cui.com
CUI Inc │ SERIES: VLED15 │ DESCRIPTION: LED DRIVER
date 07/18/2012 │ page 2 of 5
PART NUMBER KEY
VLED15 - XXX - XXXX
Base Number
Input Voltage
120 = 120 Vac
230 = 230 Vac
Output Current
(in mA)
INPUT
parameter
conditions/description
min
typ
max
units
90
176
135
265
Vac
Vac
voltage
frequency
47
63
0.22
5
Hz
A
input current
inrush current
power factor
at 115 Vac
at 25°C
A
at 120 Vac
90
%
OUTPUT
parameter
conditions/description
min
typ
±5
±5
max
units
%
voltage accuracy
load regulation
of set point
%
PROTECTION
parameter
conditions/description
auto restart
over voltage protection
over current protection
short circuit protection
control
auto restart
auto restart
output dims without any flicker
dimming range
(conduction angle/output)
use with incandescent dimmer
auto restart
30
147
degrees
over temperature protection
SAFETY & COMPLIANCE
parameter
conditions/description
min
typ
max
units
isolation
meets the UL 60950-1 reinforced, double insulation NEC (Class 2) EN 60598-1 class II
UL 60950-1, LPS, UL 8750, EN61347-2-13
safety approvals
EN 55015 class B, FCC class 47 CFR part 15 class B, EN 61000-4-(2,3,4,5,6,11), IEC 61000-3-(2,3)
ANSI c62.41-1991 category A1, 2.5 kV Ringwave
EMI/EMC
harmonics
meets EN 61000-3-(2,3)
leakage current
RoHS compliant
at 120 Vac
yes
0.25
mA
ENVIRONMENTAL
parameter
conditions/description
min
-30
-40
5
typ
max
90
units
°C
operating temperature
storage temperature
operating humidity
surface temperature
95
°C
non-condensing
95
%
exposed surfaces, under all operating conditions
90
°C
cui.com
CUI Inc │ SERIES: VLED15 │ DESCRIPTION: LED DRIVER
date 07/18/2012 │ page 3 of 5
MECHANICAL
parameter
conditions/description
82 x 56 x 29 (3.21 x 2.21 x 1.13 inch)
min
typ
max
units
mm
inch
dimensions
145
5.1
g
oz
weight
MECHANICAL DRAWING
units: mm
tolerance: ±0.3 mm (unless otherwise specified)
56.22 2.213
SCALE: 1:2
81.62 3.213
152.00 5.984
(2 PLCS) 5.00
9.50 0.374
(2 PLCS)
cui.com
CUI Inc │ SERIES: VLED15 │ DESCRIPTION: LED DRIVER
date 07/18/2012 │ page 4 of 5
DIMMING REQUIREMENTS
Dimming of the driver shall be possible with standard triac based incandescent dimmers that chops the AC
voltage as shown below or with Electronic Low Voltage dimmers that employ reverse phase control.
Chopped AC Input to Driver
AC Wall Power
During the rapid rise time of the AC voltage when the dimmer turns on, the driver shall not generate any
voltage or current oscillations and inrush current shall be controlled. During the on time of the AC input, the
driver shall regulate the output. The RMS value of the driver output current shall be proportional to the on
time of the AC input voltage. Care must be taken to assure that the minimum load requirements are met.
Multiple drivers/LEDs may be connected to the dimmer in order to meet the minimum load requirement.
DIMMING RANGE
When operating with an incandescent dimmer, the RMS output current shall vary depending upon the
conduction angle and RMS value of the applied AC input voltage. The following graph shows the typical output
versus conduction angle at various line voltages.
Typical Io vs Conducꢀon Angle
1.2
1
100V (200V)
0.8
115V (230V)
132V (264V)
0.6
0.4
0.2
0
0
20
40
60
80
100
120
140
160
VAC Conducꢀon Angle (Degrees)
The specified dimming range shall be from 30 degrees through 147 degrees conduction angle. Operation
throughout this dimming range shall be monotonic and produce a smooth transition of light output in both
directions of the dimming range. At 120 Vac or 240 Vac input, the driver shall achieve full rated output
current at less than 147 degree conduction angle.
cui.com
CUI Inc │ SERIES: VLED15 │ DESCRIPTION: LED DRIVER
date 07/18/2012 │ page 5 of 5
REVISION HISTORY
rev.
description
date
1.0
initial release
07/29/2010
03/21/2011
02/15/2012
04/24/2012
07/18/2012
1.01
1.02
1.03
1.04
model update and added dimensions
applied new spec template
updated input voltage
new template applied
The revision history provided is for informational purposes only and is believed to be accurate.
Headquarters
20050 SW 112th Ave.
Tualatin, OR 97062
800.275.4899
Fax 503.612.2383
cui.com
techsupport@cui.com
CUI offers a one (1) year limited warranty. Complete warranty information is listed on our website.
CUI reserves the right to make changes to the product at any time without notice. Information provided by CUI is believed to be accurate and reliable. However, no responsibility is
assumed by CUI for its use, nor for any infringements of patents or other rights of third parties which may result from its use.
CUI products are not authorized or warranted for use as critical components in equipment that requires an extremely high level of reliability. A critical
component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to
affect its safety or effectiveness.
相关型号:
©2020 ICPDF网 联系我们和版权申明