VPF-S600-24R [CUI]

Switching Power Supply; 开关电源


型号：	VPF-S600-24R
厂家：	CUI INC
描述：	Switching Power Supply 开关电源开关
文件：	总5页 (文件大小：308K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

1 / 5

VPF-S600 Switching Power Supply

Rev. 12-2006

Features

·Built-in active PFC function

·Short Circuit, overload, over voltage,

over temperature protected

·Current Sharing (Available)

·Current Monitoring

·Power Good Signal

·Built-in Remote Inhibit

·Built-in Remote Sense

·Extended temperature range: -40 ~ +75 ºC

available

7, 8

Preset

Output Current

Ripple & Noise

2, 3, 4

5, 6

Model

Voltage Output

Minimum

0 A

Maximum

90 A

Max. Power

297 W

Regulation

+/- 1%

(Vpp)

VPF-S600-03R(I)

VPF-S600-05R(I)

VPF-S600-12R(I)

VPF-S600-16R(I)

VPF-S600-24R(I)

VPF-S600-36R(I)

VPF-S600-48R(I)

3.3V

2 - 3.3 V

5 - 6 V

50 mV

0 A

90 A

450 W

12V

16V

24V

36V

48V

12 - 15 V

16 - 21 V

22 - 30 V

31 - 47 V

48 - 56 V

0 A

50 A

600 W

0 A

37.5 A

27.27 A

19.35 A

12.5 A

600 W

0 A

600 W

0 A

600 W

0 A

600 W

Notes:

1 Adding “I” Indicates Current sharing model.

2 Customer must specify output voltage.

3 Output is fully isolated.

4 Output voltage is measured at output power connector.

5 Provides peak power of 900 W within 500 µS for all models. For longer duty duration please contact us.

6 Must use external forced airflow min. 30 CFM to achieve maximum power.

7 1% minimum load is required to maintain the ripple and regulation.

8 Ripple and noise is measured from 10 KHz to 20 MHz at output terminals with a 0.1 µF ceramic capacitor and

a 22 µF electrolytic capacitor in parallel.

V-Infinity, LLC, 20050 SW 112th Ave., Tualatin, OR 97062

www.v-infinity.com

1-866-372-1258

2 / 5

VPF-S600 Switching Power Supply

Rev. 12-2006

Input

Parameter

Conditions/Description

Min

Nom

Max

Units

Input Frequency

Input Voltage

Input Current

Inrush Current

Power Factor

264

VAC

At 90-264 VAC

Peak measured at 230 VAC at full load, cold start

Active power factor correction meets EN61000-3-2 class D

Output

Parameter

Conditions/Description

Min

Nom

Max

Units

Transient response Output voltage returns to within 1% in less than

2.5 mS for a 50% load change. Peak

transient does not exceed 5%.

Overshoot

Efficiency

Turn-on and turn-off overshoot shall not exceed

5% over nominal voltage.

Measured at 230 V and full load

12 V model:

80%

82%

All other models:

Turn on delay

Hold up time

Adjustability

Remote sense

At 120 VAC

second

At 120 VAC and 80% of rated maximim load

Adjustable with built-in trim pot.

+/- 5%

Designated as RS+ and RS- on the CN3. Total voltage compensation for cable losses with

respect to the main output. (NOT available for current sharing models.)

Designated as RSW on the CN3. Requires a low signal to inhibit the output.

Green - the power supply is operating normally.

Remote Inhibit

LED display

(LED 1)

Orange - when any protection occurs or when Remote Inhibit is in effect.

Designated as PG on the CN3. This signal

Power Good

goes high 100-500 mS after the output reaches regulation.

It goes low at least 1 mS before loss of regulation.

Current Sharing

Current Monitor

Designated as CSH on (CN3), use in parallel for forced current sharing function.

Accuracy of shared current with up to 4 parallel units is within 10% at full load.

Disignated as CMN on (CN3) for current sense purpose. CMN is a 0.5 to 3VDC output

voltage to represent a linear 0% to 100% output current.

Protection Circuit

Parameter

Conditions/Description

Input Fuse

Built-in ac fuse. A blown fuse usually indicates permanent

damage to the power supply serviceable by factory only.

Power supply shuts down when ac input is under

Input under-voltage

Overload

80 VAC. When ac line reappears over 86 +/- 5 VAC,

the power supply restarts automatically.

Current limiting starts at 110-140% of the rated output current and

recovers automatically.

Short circuit

Short circuit can be continuous. Recovers automatically upon removal of short.

Output is protected agaist overvoltage. Unit shuts down and latches

when voltage at output terminals exceeds 130%. AC input needs to be

reset to restart the power supply.

Output Over-voltage

Over temp.

Power supply shuts down when temperature is in excess of 85 ºC. Auto recovery.

V-Infinity, LLC, 20050 SW 112th Ave., Tualatin, OR 97062

www.v-infinity.com

1-866-372-1258

3 / 5

VPF-S600 Switching Power Supply

Rev. 12-2006

General and Safety

Parameter

Conditions/Description

Min

Nom

Max

Units

Operating temp.

Derates linearly from 100% load at 50 ºC to 50%

load at 70 ºC.

ºC

Optional operating

temp.

Derates linearly from 100% load at 50 ºC to 37.5%

load at 75 ºC.

-40

ºC

Storage temp.

Optional storage

temp.

-20

-40

ºC

Operating humid.

Storage humid.

EMI

Non-condensing

90%

95%

Pass FCC Part 15 Subject J Class B, CISPR 22 class B, CE Mark

Safety

UL60950-1 (E222889), CSA C22.2 No. 950-95, TUV EN60950 and CB

Leakage Current

Isolation Voltage

(HI-POT)

at 264 VAC

3.5

0.1

Applied for 3 seconds

Primary to secondary:

3000

1500

VAC

Ohm

Primary to transformer core:

Primary to earth ground:

Grounding Test

Allowable resistance measured when 25 A current is

applied from the ground pin of the three prong plug

to the farthest earthed connection point.

Standard warranty length

Warranty

MTBF

years

hours

According to MIL-HDBK-217 at 30 ºC

Full load, at 45 +/- 5 ºC, 230 VAC. Burn-in for

up to 8 hours in early productions. Time

reduced gradually as product matures.

150,000

Burn-in

Note: Customer must specify extended temperature on PO.

Mechanical

Parameter

Conditions/Description

Min

Nom

Max

Units

grams

inches

Weight

1450

Enclosure

Mounting holes

8.00(L) x 4.33(W) x 2.56(H)

Two sets of 8 threaded mounting holes available on the enclosure

B: 6-32, maximum insertion depth of 0.2 inches.

C: M4, maximum insertion depth of 0.2 inches.

Input Connector - (CN1)

Parameter

Conditions/Description

AC input (Option 1) Molex Part No. 26-48-1201 or similar (5 pin).

Suggested mating plug: Molex Part No. 09-91-0500 or equivalent (5 pin, 3 used)

AC Input (Option 2) Howder Terminal block Part No. HD-121-3P (3 pin, M3 Screw) 9.5mm spacing

Suggested mating connector: Molex 19198-0045 or similar

Note: Input connector needs to be specified on the PO.

V-Infinity, LLC, 20050 SW 112th Ave., Tualatin, OR 97062

www.v-infinity.com

1-866-372-1258

4 / 5

VPF-S600 Switching Power Supply

Rev. 12-2006

Output Connector - (CN2)

Conditions/Description

Parameter

Output (Option 1)

Molex Part No. 26-48-1201 or similar.(20 pin)

Output pin assignment, VO+ (Pins 1-10), VO- (Pins 11-20)

Suggested mating connector: Molex Part No. 09-91-2000, contact:08-50-0106 or similar.

Howder Terminal block Part No. HD-121-8P (8 pin, M3.5 Screw) 9.5mm spacing

Output pin assignment, VO+ (Pins 1-4), VO- (Pins 5-8)

Output (Option 2)

Suggested mating connector: Molex 19198-0045 or similar.

Note: Output connector needs to be specified on the PO.

Logic Connector - (CN3)

Parameter

Conditions/Description

Logic

JS B7B-XH-A

Suggested mating connector: JST XHP-7 or equivalent , Contact: SXH-001T-P0.6.

1. CMN - Current Monitoring

Pin Assignments:

2. CSH - Current Sharing

3. RTN - Return / Output Ground

4. PG - Power Good Signal

5. RSW - (Remote On-Off / Remote Inhibit)

6. RS(-) - Remote Sense

7. RS(+) - Remote Sense

Fan

JST B2B-XH-A

Suggested mating connector: JST XHP-2 or equivalent, Contact: SXH-001T-P0.6.

V-Infinity, LLC, 20050 SW 112th Ave., Tualatin, OR 97062

www.v-infinity.com

1-866-372-1258

5 / 5

VPF-S600 Switching Power Supply

Rev. 12-2006

V-Infinity, LLC, 20050 SW 112th Ave., Tualatin, OR 97062

www.v-infinity.com

1-866-372-1258

相关型号：

VPF-S600-36R

Switching Power Supply

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-

CUI

VPF-S600-48R

Switching Power Supply

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-

CUI

CUI