CY62137VNLL-55ZXI [CYPRESS]
2-Mbit (128K x 16) Static RAM; 2兆位( 128K ×16 )静态RAM型号: | CY62137VNLL-55ZXI |
厂家: | CYPRESS |
描述: | 2-Mbit (128K x 16) Static RAM |
文件: | 总11页 (文件大小:468K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
CY62137VN MoBL®
2-Mbit (128K x 16) Static RAM
portable applications such as cellular telephones. The device
also has an automatic power-down feature that reduces power
consumption by 99% when addresses are not toggling. The
device can also be put into standby mode when deselected
(CE HIGH) or when CE is LOW and both BLE and BHE are
HIGH. The input/output pins (I/O0 through I/O15) are placed in
a high-impedance state when: deselected (CE HIGH), outputs
are disabled (OE HIGH), BHE and BLE are disabled (BHE,
BLE HIGH), or during a write operation (CE LOW, and WE
LOW).Writing to the device is accomplished by taking Chip
Enable (CE) and Write Enable (WE) inputs LOW. If Byte Low
Enable (BLE) is LOW, then data from I/O pins (I/O0 through
I/O7), is written into the location specified on the address pins
(A0 through A16). If Byte High Enable (BHE) is LOW, then data
from I/O pins (I/O8 through I/O15) is written into the location
specified on the address pins (A0 through A16).Reading from
the device is accomplished by taking Chip Enable (CE) and
Output Enable (OE) LOW while forcing the Write Enable (WE)
HIGH. If Byte Low Enable (BLE) is LOW, then data from the
memory location specified by the address pins will appear on
I/O0 to I/O7. If Byte High Enable (BHE) is LOW, then data from
memory will appear on I/O8 to I/O15. See the truth table at the
back of this data sheet for a complete description of read and
write modes.
Features
• Temperature Ranges
— Industrial: –40°C to 85°C
— Automotive-A: –40°C to 85°C
— Automotive-E: –40°C to 125°C
• High Speed: 55 ns
• Wide voltage range: 2.7V–3.6V
• Ultra-low active, standby power
• Easy memory expansion with CE and OE features
• TTL-compatible inputs and outputs
• Automatic power-down when deselected
• CMOS for optimum speed/power
• Available in Pb-free 44-pin TSOP Type II package
Functional Description[1]
The CY62137VN is a high-performance CMOS static RAM
organized as 128K words by 16 bits. This device features
advanced circuit design to provide ultra-low active current.
This is ideal for providing More Battery Life™ (MoBL®) in
Logic Block Diagram
DATA IN DRIVERS
10
A10
A9
A8
A7
A6
A5
A4
A3
A2
128K x 16
RAM Array
I/O0–I/O7
I/O8–I/O15
A1
A0
COLUMN DECODER
BHE
WE
CE
OE
BLE
CE
Power-down
Circuit
BHE
BLE
Note:
1. For best practice recommendations, please refer to the Cypress application note “System Design Guidelines” on http://www.cypress.com.
Cypress Semiconductor Corporation
Document #: 001-06497 Rev. *A
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised August 3, 2006
[+] Feedback
CY62137VN MoBL®
Product Portfolio
Power Dissipation
Speed
(ns)
Operating, ICC
(mA)
Standby, ISB2
VCC Range (V)
Typ.[3]
(µA)
Product
Min.
Max.
Typ.[3]
Max.
20
Typ.[3]
Max.
15
CY62137VNLL Industrial
CY62137VNLL
2.7
3.0
3.6
55
70
70
70
7
7
7
7
1
1
1
1
15
15
CY62137VNLL Automotive-A
CY62137VNLL Automotive-E
15
15
15
20
Pin Configurations
TSOP II (Forward)
Top View
44
1
A
4
A
5
43
42
41
40
39
38
A
A
2
3
4
5
6
3
6
A
A
2
7
OE
A
1
BHE
BLE
I/O
A
0
CE
I/O
7
0
15
37
36
35
34
33
I/O
I/O
8
I/O
I/O
1
2
14
13
12
9
10
11
12
13
I/O
V
SS
I/O
3
CC
V
SS
V
V
CC
32
I/O
I/O
I/O
4
5
6
7
11
10
31
30
29
28
I/O
I/O
I/O
14
15
16
I/O
9
8
I/O
WE 17
NC
18
27
26
25
A
A
8
16
19
A
A
15
9
A
14
20
21
22
A
11
10
A
A
24
23
13
A12
NC
Pin Definitions
Pin Number
Type
Description
1–5, 18–22, 24–27, 42–45 Input
A0–A16. Address Inputs
7–10, 13–16, 29–32, 35–38 Input/Output I/O0–I/O15. Data lines. Used as input or output lines depending on operation
23
17
No Connect NC. This pin is not connected to the die
Input/Control WE. When selected LOW, a WRITE is conducted. When selected HIGH, a READ is
conducted
6
Input/Control CE. When LOW, selects the chip. When HIGH, deselects the chip
40, 39
Input/Control Byte Write Select Inputs, active LOW. BHE controls I/O15–I/O8, BLE controls
I/O7–I/O0.
41
Input/Control OE. Output Enable. Controls the direction of the I/O pins. When LOW, the I/O pins
behave as outputs. When deasserted HIGH, I/O pins are tri-stated, and act as input
data pins
12, 34
Ground
VSS. Ground for the device
11, 33
Power Supply VCC. Power supply for the device
Notes:
2. NC pins are not connected on the die.
3. Typical values are included for reference only and are not guaranteed or tested. Typical values are measured at V = V
., T = 25°C.
A
CC
CC(TYP)
Document #: 001-06497 Rev. *A
Page 2 of 11
[+] Feedback
CY62137VN MoBL®
Output Current into Outputs (LOW)............................. 20 mA
Maximum Ratings
Static Discharge Voltage...........................................> 2001V
(per MIL-STD-883, Method 3015)
(Above which the useful life may be impaired. For user guide-
lines, not tested.)
Latch-up Current.....................................................> 200 mA
Storage Temperature .................................–65°C to +150°C
Operating Range
Ambient Temperature with
Power Applied.............................................–55°C to +125°C
Ambient
Supply Voltage to Ground Potential............... –0.5V to +4.6V
Range
Temperature
–40°C to +85°C
–40°C to +85°C
–40°C to +125°C
VCC
DC Voltage Applied to Outputs
Industrial
2.7V to 3.6V
in High-Z State[4] ....................................–0.5V to VCC + 0.5V
Automotive-A
Automotive-E
DC Input Voltage[4].................................–0.5V to VCC + 0.5V
Electrical Characteristics Over the Operating Range
-55
-70
Parameter
VOH
Description
Test Conditions
Min. Typ.[3] Max. Min. Typ.[3] Max. Unit
Output HIGH Voltage VCC = 2.7V, IOH = –1.0 mA
Output LOW Voltage VCC = 2.7V, IOL = 2.1 mA
Input HIGH Voltage
2.4
2.2
2.4
2.2
V
V
V
VOL
0.4
0.4
VIH
VCC
+
VCC +
0.5V
0.5V
VIL
IIX
Input LOW Voltage
–0.5
–1
0.8
–0.5
–1
0.8
V
Input Leakage
Current
GND < VI < VCC
+1
+1
µA
IOZ
ICC
Output Leakage
Current
GND < VO < VCC, Output Disabled
–1
+1
20
–1
+1
µA
VCC Operating
Supply
Current
IOUT = 0 mA,
f = fMAX = 1/tRC
CMOS Levels
VCC = 3.6V Ind’l
7
1
7
7
15
15
mA
,
Auto-A/
Auto-E
IOUT = 0 mA,
f = 1 MHz,
CMOS Levels
Ind’l
2
1
1
2
2
mA
Auto-A/
Auto-E
ISB1
Automatic CE
Power-down
Current—CMOS
Inputs
CE > VCC – 0.3V, VCC = 3.6V Ind’l
100
100
100
µA
VIN > VCC – 0.3V
Auto-A/
Auto-E
or VIN < 0.3V,
f = fMAX
ISB2
Automatic CE
Power-down
Current—CMOS
Inputs
CE > VCC – 0.3V VCC = 3.6V Ind’l/
1
15
1
1
1
15
15
20
µA
VIN > VCC – 0.3V
Auto-A
Auto-E
or VIN < 0.3V,
f = 0
Capacitance[5]
Parameter
Description
Input Capacitance
Output Capacitance
Test Conditions
Max.
Unit
CIN
TA = 25°C, f = 1 MHz,
CC = VCC(typ)
6
8
pF
pF
V
COUT
Thermal Resistance[5]
Parameter
Description
Test Conditions
TSOPII
60
Unit
ΘJA
ΘJC
Thermal Resistance (Junction to Ambient) Still Air, soldered on a 4.25 x 1.125 inch,
°C/W
°C/W
2-layer printed circuit board
Thermal Resistance (Junction to Case)
22
Notes:
4. V (min.) = –2.0V for pulse durations less than 20 ns.
IL
5. Tested initially and after any design or process changes that may affect these parameters.
Document #: 001-06497 Rev. *A
Page 3 of 11
[+] Feedback
CY62137VN MoBL®
AC Test Loads and Waveforms
R1
R1
ALL INPUT PULSES
VCC
VCC
OUTPUT
VCC Typ
GND
90%
90%
OUTPUT
10%
10%
R2
5 pF
R2
30 pF
INCLUDING
JIG AND
SCOPE
Fall Time:
1 V/ns
Rise Time:
1 V/ns
INCLUDING
JIG AND
SCOPE
(a)
(b)
(c)
Equivalent to:
THÉVENIN EQUIVALENT
RTH
OUTPUT
VTH
Parameters
Value
Unit
Ohms
Ohms
Ohms
Volts
R1
R2
1105
1550
645
RTH
VTH
1.75
Data Retention Characteristics (Over the Operating Range)
Parameter
VDR
Description
Conditions
Min.
Typ.[3]
Max.
Unit
V
VCC for Data Retention
Data Retention Current
1.0
ICCDR
VCC = 1.0V, CE > VCC – 0.3V,
IN > VCC – 0.3V or VIN < 0.3V;
No input may exceed VCC + 0.3V
Ind’l/Auto-A
Auto-E
0.5
7.5
10
µA
V
[5]
tCDR
Chip Deselect to Data
Retention Time
0
ns
ns
tR
Operation Recovery Time
tRC
Data Retention Waveform
DATA RETENTION MODE
> 1.0 V
VCC(min.)
VCC(min.)
V
VCC
CE
DR
t
t
R
CDR
Document #: 001-06497 Rev. *A
Page 4 of 11
[+] Feedback
CY62137VN MoBL®
[6]
Switching Characteristics Over the Operating Range
55 ns
70 ns
Parameter
Read Cycle
Description
Min.
55
Max.
Min.
70
Max.
Unit
tRC
Read Cycle Time
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
tAA
Address to Data Valid
55
70
tOHA
tACE
tDOE
tLZOE
tHZOE
tLZCE
tHZCE
tPU
Data Hold from Address Change
CE LOW to Data Valid
OE LOW to Data Valid
OE LOW to Low-Z[7]
10
10
55
25
70
35
5
10
0
5
10
0
OE HIGH to High-Z[7, 8]
CE LOW to Low-Z[7]
25
25
25
25
CE HIGH to High-Z[7, 8]
CE LOW to Power-up
tPD
CE HIGH to Power-down
BHE / BLE LOW to Data Valid
BHE / BLE LOW to Low-Z
BHE / BLE HIGH to High-Z
55
55
70
70
tDBE
tLZBE
tHZBE
(9)
5
5
25
25
Write Cycle[10, 11]
tWC
Write Cycle Time
55
45
45
0
70
60
60
0
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
tSCE
tAW
CE LOW to Write End
Address Set-up to Write End
Address Hold from Write End
Address Set-up to Write Start
WE Pulse Width
tHA
tSA
0
0
tPWE
tSD
40
25
0
50
30
0
Data Set-up to Write End
Data Hold from Write End
WE LOW to High-Z[7, 8]
WE HIGH to Low-Z[7]
tHD
tHZWE
tLZWE
20
25
5
10
60
tBW
BHE / BLE LOW to End of Write
50
Notes:
6. Test conditions assume signal transition time of 5 ns or less, timing reference levels of 1.5V, input levels of 0 to V typ., and output loading of the specified
CC
I
/I and 30 pF load capacitance.
OL OH
7. At any given temperature and voltage condition, t
is less than t
, t
is less than t
, and t
is less than t
for any given device.
HZCE
LZCE HZOE
LZOE
HZWE
LZWE
8. t
, t
, and t
are specified with C = 5 pF as in (b) of AC Test Loads. Transition is measured ±500 mV from steady-state voltage.
HZOE HZCE
HZWE L
9. If both byte enables are toggled together this value is 10 ns.
10. The internal write time of the memory is defined by the overlap of CE LOW and WE LOW. Both signals must be LOW to initiate a write and either signal can
terminate a write by going HIGH. The data input set-up and hold timing should be referenced to the rising edge of the signal that terminates the write.
11. The minimum write cycle time for write cycle #3 (WE controlled, OE LOW) is the sum of t
and t
.
HZWE
SD
Document #: 001-06497 Rev. *A
Page 5 of 11
[+] Feedback
CY62137VN MoBL®
Switching Waveforms
Read Cycle No. 1[12, 13]
t
RC
ADDRESS
t
AA
t
OHA
DATA OUT
PREVIOUS DATA VALID
DATA VALID
Read Cycle No. 2[13, 14]
t
RC
CE
t
PD
HZCE
t
t
ACE
OE
t
HZOE
t
DOE
BHE/BLE
t
LZOE
t
HZBE
t
DBE
t
LZBE
HIGH
IMPEDANCE
HIGH IMPEDANCE
DATA OUT
DATA VALID
t
LZCE
t
PU
V
ICC
ISB
CC
SUPPLY
CURRENT
50%
50%
Notes:
12. Device is continuously selected. OE, CE = V .
IL
13. WE is HIGH for read cycle.
14. Address valid prior to or coincident with CE transition LOW.
Document #: 001-06497 Rev. *A
Page 6 of 11
[+] Feedback
CY62137VN MoBL®
Switching Waveforms (continued)
Write Cycle No. 1 (WE Controlled)[10, 15, 16]
t
WC
ADDRESS
CE
t
t
HA
AW
t
SA
t
PWE
WE
t
BW
BHE/BLE
OE
t
SD
t
HD
DATA VALID
DATA I/O
NOTE 17
IN
t
HZOE
Write Cycle No. 2 (CE Controlled)[10, 15, 16]
t
WC
ADDRESS
CE
t
SCE
t
SA
t
t
HA
AW
t
BW
BHE/BLE
t
PWE
WE
t
t
HD
SD
DATA I/O
DATA VALID
IN
Notes:
15. Data I/O is high-impedance if OE = V
.
IH
16. If CE goes HIGH simultaneously with WE HIGH, the output remains in a high-impedance state.
17. During this period, the I/Os are in output state and input signals should not be applied.
Document #: 001-06497 Rev. *A
Page 7 of 11
[+] Feedback
CY62137VN MoBL®
Switching Waveforms (continued)
Write Cycle No. 3 (WE Controlled, OE LOW)[11, 16]
t
WC
ADDRESS
CE
t
t
HA
AW
t
BW
BHE/BLE
t
SA
WE
t
t
HD
SD
DATA I/O
DATA VALID
NOTE 17
IN
t
t
LZWE
HZWE
Write Cycle No. 4 (BHE/BLE Controlled, OE LOW)[17]
t
WC
ADDRESS
CE
t
t
HA
AW
t
BW
BHE/BLE
WE
t
SA
t
t
HD
SD
DATA I/O
DATA VALID
NOTE 17
IN
t
t
LZWE
HZWE
Document #: 001-06497 Rev. *A
Page 8 of 11
[+] Feedback
CY62137VN MoBL®
Typical DC and AC Characteristics
Normalized Operating Current
vs. Supply Voltage
Standby Current vs. Supply Voltage
35
1.4
1.2
MoBL
30
MoBL
25
20
15
1.0
0.8
0.6
10
0.4
5
0
0.2
0.0
2.7
1.0
3.7
2.8
1.9
1.7
2.2
2.7
3.2
3.7
SUPPLY VOLTAGE (V)
SUPPLY VOLTAGE (V)
Access Time vs. Supply Voltage
80
70
MoBL
60
50
40
30
20
10
1.0
3.7
2.8
1.9
2.7
SUPPLY VOLTAGE (V)
Truth Table
CE
H
X
L
WE
X
OE
BHE
BLE
X
I/O8–I/O15
I/O0–I/O7
High-Z
Mode
Deselect/Power-down
Deselect/Power-down
Read
Power
X
X
L
X
H
L
High-Z
High-Z
Data Out
High-Z
Data Out
High-Z
Data In
High-Z
Data In
Standby (ISB
)
)
X
H
L
High-Z
Standby (ISB
H
H
H
H
L
Data Out
Data Out
High-Z
Active (ICC
Active (ICC
Active (ICC
Active (ICC
Active (ICC
Active (ICC
Active (ICC
)
)
)
)
)
)
)
L
L
H
L
L
Read
L
L
H
X
Read
L
H
X
X
X
X
L
High-Z
Data In
Data In
High-Z
Output Disabled
Write
L
L
L
L
H
L
L
Write
L
L
H
Write
Document #: 001-06497 Rev. *A
Page 9 of 11
[+] Feedback
CY62137VN MoBL®
Ordering Information
Speed
(ns)
Package
Diagram
Operating
Range
Ordering Code
Package Type
55
CY62137VNLL-55ZXI
CY62137VNLL-70ZXI
CY62137VNLL-70ZSXA
CY62137VNLL-70ZSXE
51-85087 44-pin TSOP II (Pb-free)
44-pin TSOP II (Pb-free)
Industrial
Industrial
70
44-pin TSOP II (Pb-free)
Automotive-A
Automotive-E
44-pin TSOP II (Pb-free)
Please contact your local Cypress sales representative for availability of these parts
Package Diagram
44-Pin TSOP II (51-85087)
DIMENSION IN MM (INCH)
MAX
MIN.
PIN 1 I.D.
22
1
R
O
E
K
A
X
S G
EJECTOR PIN
23
44
TOP VIEW
BOTTOM VIEW
10.262 (0.404)
10.058 (0.396)
0.400(0.016)
0.300 (0.012)
0.800 BSC
(0.0315)
BASE PLANE
0.210 (0.0083)
0.120 (0.0047)
0°-5°
0.10 (.004)
18.517 (0.729)
18.313 (0.721)
0.597 (0.0235)
0.406 (0.0160)
SEATING
PLANE
51-85087-*A
MoBL is a registered trademark, and More Battery Life is a trademark, of Cypress Semiconductor Corporation. All product and
company names mentioned in this document are the trademarks of their respective holders.
Document #: 001-06497 Rev. *A
Page 10 of 11
© Cypress Semiconductor Corporation, 2006. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use
of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be
used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its
products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress
products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
[+] Feedback
CY62137VN MoBL®
Document History Page
Document Title: CY62137VN MoBL® 2-Mbit (128K x 16) Static RAM
Document Number: 001-06497
Orig. of
REV. ECN NO. Issue Date Change
Description of Change
**
426503
488954
See ECN
See ECN
NXR
NXR
New Data Sheet
*A
Added Automotive product
Updated Ordering Information table
Document #: 001-06497 Rev. *A
Page 11 of 11
[+] Feedback
相关型号:
CY62138CV25LL-55BVIT
Standard SRAM, 256KX8, 55ns, CMOS, PBGA36, 6 X 8 MM, 1 MM HEIGHT, VFBGA-36
CYPRESS
©2020 ICPDF网 联系我们和版权申明