CY7C135-20JCT [CYPRESS]
Dual-Port SRAM, 4KX8, 20ns, CMOS, PQCC52, PLASTIC, LCC-52;型号: | CY7C135-20JCT |
厂家: | CYPRESS |
描述: | Dual-Port SRAM, 4KX8, 20ns, CMOS, PQCC52, PLASTIC, LCC-52 静态存储器 内存集成电路 |
文件: | 总12页 (文件大小:401K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
CY7C135, CY7C135A
CY7C1342
4K x 8 Dual-Port Static RAM and 4K x 8
Dual-Port SRAM with Semaphores
Features
Functional Description
■
True dual-ported memory cells, which allow simultaneous
reads of the same memory location
The CY7C135/135A[1] and CY7C1342 are high speed CMOS 4K
x 8 dual-port static RAMs. The CY7C1342 includes semaphores
that provide a means to allocate portions of the dual-port RAM
or any shared resource. Two ports are provided permitting
independent, asynchronous access for reads and writes to any
location in memory. Application areas include interpro-
■
■
■
■
■
■
■
4K x 8 organization
0.65 micron CMOS for optimum speed and power
High speed access: 15 ns
cessor/multiprocessor
designs,
communications
status
buffering, and dual-port video/graphics memory.
Low operating power: ICC = 160 mA (max)
Fully asynchronous operation
Automatic power down
Each port has independent control pins: chip enable (CE), read
or write enable (R/W), and output enable (OE). The
CY7C135/135A is suited for those systems that do not require
on-chip arbitration or are intolerant of wait states. Therefore, the
user must be aware that simultaneous access to a location is
possible. Semaphores are offered on the CY7C1342 to assist in
arbitrating between ports. The semaphore logic is comprised of
eight shared latches. Only one side can control the latch
(semaphore) at any time. Control of a semaphore indicates that
a shared resource is in use. An automatic power down feature is
controlled independently on each port by a chip enable (CE) pin
or SEM pin (CY7C1342 only).
Semaphores included on the 7C1342 to permit software
handshaking between ports
■
■
Available in 52-pin PLCC
Pb-free packages available
The CY7C135/135A and CY7C1342 are available in 52-pin
PLCC.
Logic Block Diagram
R/WL
R/WR
CEL
OEL
CER
OER
I/O7L
I/O7R
I/O0R
I/O
CONTROL
I/O
CONTROL
I/O0L
A11L
A11R
ADDRESS
DECODER
ADDRESS
DECODER
MEMORY
ARRAY
A0L
A0R
SEMAPHORE
ARBITRATION
(7C1342 only)
CEL
OEL
CER
OER
R/WL
R/WR
(7C1342 only)
(7C1342 only)
SEMR
SEML
Note
1. CY7C135 and CY7C135A are functionally identical
Cypress Semiconductor Corporation
Document #: 38-06038 Rev. *D
•
198 Champion Court
•
San Jose
,
CA 95134-1709
•
408-943-2600
Revised December 09, 2008
[+] Feedback
CY7C135, CY7C135A
CY7C1342
Selection Guide
7C135-15
7C135-20 7C135/135A-25
7C135-35
7C1342-35
7C135-55
7C1342-55
Unit
Parameter
7C1342-15 7C1342-20
7C1342-25
Maximum Access Time
15
220
60
20
190
50
25
180
40
35
160
30
55
160
30
ns
Maximum Operating Current Commercial
mA
mA
Maximum Standby Current for Commercial
ISB1
Pin Configurations
Figure 1. Pin Diagram - CY7C135/135A (Top View)
Figure 2. Pin Diagram - CY7C1342 (Top View)
7
6 5 4 3 2 1 52 51 50 49 48 47
7
6
5
4
3
2
1
52 51 50 49 48 47
46
A
A
OE
1L
2L
3L
4L
5L
6L
7L
8L
9L
0L
1L
8
46
45
44
43
42
41
40
39
38
37
36
35
34
R
A
A
OE
1L
2L
3L
4L
5L
6L
7L
8L
9L
0L
1L
2L
3L
8
R
A
0R
A
1R
A
2R
A
3R
A
4R
A
5R
9
A
0R
9
45
44
43
42
41
40
39
38
37
36
35
34
A
10
11
12
13
14
15
16
17
18
19
20
A
A
1R
10
11
12
13
14
15
16
17
18
19
20
A
A
A
2R
A
A
A
3R
A
7C135/135A
A
A
4R
7C1342
A
A
A
5R
A
A
6R
A
7R
A
8R
A
9R
A
A
6R
A
A
A
7R
I/O
I/O
I/O
I/O
I/O
I/O
A
8R
A
9R
I/O
I/O
2L
NC
I/O
NC
I/O
3L
7R
7R
21 22 23 24 25 26 27 28 29 30 31 32 33
21 22 23 24 25 26 27 28 29 30 31 32 33
Pin Definitions
Left Port
Right Port
A0R–11R
CER
Description
A0L–11L
CEL
Address Lines
Chip Enable
OEL
OER
Output Enable
R/WL
R/WR
Read/Write Enable
SEML
(CY7C1342
only)
SEMR
(CY7C1342
only)
Semaphore Enable. When asserted LOW, allows access to eight semaphores. The three least
significant bits of the address lines determines which semaphore to write or read. The I/O0 pin
is used when writing to a semaphore. Semaphores are requested by writing a 0 into the
respective location.
Document #: 38-06038 Rev. *D
Page 2 of 12
[+] Feedback
CY7C135, CY7C135A
CY7C1342
DC Input Voltage[3] .........................................–3.0V to +7.0V
Maximum Ratings[2]
Static Discharge Voltage...........................................> 2001V
(per MIL-STD-883, Method 3015)
Exceeding maximum ratings may shorten the useful life of the
device. User guidelines are not tested.
Latch Up Current ....................................................> 200 mA
Storage Temperature ..................................–65°C to+150°C
Operating Range
Ambient Temperature with
Power Applied .............................................–55°C to+125°C
Ambient
Temperature
Range
VCC
Supply Voltage to Ground Potential
(Pin 48 to Pin 24)............................................ –0.5V to+7.0V
Commercial
Industrial
0
°
C to +70
°
C
5V ± 10%
5V ± 10%
DC Voltage Applied to Outputs
in High Z State................................................ –0.5V to+7.0V
–40 C to +85°C
°
Electrical Characteristics Over the Operating Range
7C135-25
7C135A-25
7C1342-25
7C135-15
7C135-20
7C1342-15 7C1342-20
Parameter
Description
Test Conditions
Unit
Min Max Min Max Min Max
VOH
VOL
VIH
VIL
Output HIGH Voltage
Output LOW Voltage
Input HIGH Voltage
Input LOW Voltage
Input Load Current
Output Leakage Current
VCC = Min., IOH = –4.0 mA
VCC = Min., IOL = 4.0 mA
2.4
2.4
2.4
V
V
V
V
0.4
0.8
0.4
0.8
0.4
0.8
2.2
2.2
2.2
IIX
GND ≤ VI ≤ VCC
–10 +10 –10 +10 –10 +10 μA
–10 +10 –10 +10 –10 +10 μA
IOZ
Outputs Disabled,
GND ≤ VO ≤ VCC
ICC
Operating Current
VCC = Max.,
Com’l
Ind.
220
60
190
50
180 mA
190
IOUT = 0 mA
ISB1
ISB2
ISB3
Standby Current
(Both Ports TTL Levels)
CEL and CER ≥ VIH,
Com’l
Ind.
40
50
mA
[4]
f = fMAX
Standby Current
(One Port TTL Level)
CEL and CER ≥ VIH,
Com’l
Ind.
130
15
120
15
110 mA
120
[4]
f = fMAX
Standby Current
(Both Ports CMOS Levels) 0.2V,
Both Ports CE and CER ≥ VCC
–
Com’l
15
mA
VIN ≥ VCC – 0.2V
Ind.
30
or VIN ≤ 0.2V, f = 0[4]
ISB4
Standby Current
(One Port CMOS Level)
One Port CEL or
CER ≥ VCC – 0.2V,
VIN ≥VCC – 0.2V or
VIN ≤ 0.2V,
Com’l
Ind.
125
115
100 mA
115
Active Port Outputs,
[4]
f = fMAX
Notes
2. The voltage on any input or I/O pin cannot exceed the power pin during power up.
3. Pulse width < 20 ns.
4.
f
I
= 1/t = All inputs cycling at f = 1/t (except output enable). f = 0 means no address or control lines change. This applies only to inputs at CMOS level standby
MAX
SB3.
RC RC
Document #: 38-06038 Rev. *D
Page 3 of 12
[+] Feedback
CY7C135, CY7C135A
CY7C1342
Electrical Characteristics Over the Operating Range (continued)
7C135-35
7C135-55
7C1342-35 7C1342-55
Parameter
Description
Test Conditions
Unit
Min Max Min Max
VOH
VOL
VIH
VIL
IIX
Output HIGH Voltage
Output LOW Voltage
VCC = Min., IOH = –4.0 mA
2.4
2.2
2.4
2.2
V
V
VCC = Min., IOL = 4.0 mA
0.4
0.8
0.4
0.8
V
Input LOW Voltage
Input Load Current
Output Leakage Current
Operating Current
V
GND ≤ VI ≤ VCC
–10 +10 –10 +10
–10 +10 –10 +10
μA
μA
mA
IOZ
ICC
Outputs Disabled, GND ≤ VO ≤ VCC
VCC = Max., IOUT = 0 mA
VCC = Max., IOUT = 0 mA
Com’l
Ind.
160
180
30
160
180
30
[4]
ISB1
ISB2
ISB3
Standby Current
(Both Ports TTL Levels)
CEL and CER ≥ VIH, f = fMAX
Com’l
Ind.
mA
mA
mA
40
40
[4]
Standby Current
(One Port TTL Level)
CEL and CER ≥ VIH, f = fMAX
Com’l
Ind.
100
110
15
100
110
15
Standby Current
(Both Ports CMOS Levels) VIN ≥ VCC – 0.2V
Both Ports CE and CER ≥ VCC – 0.2V, Com’l
Ind.
30
30
or VIN ≤ 0.2V, f = 0[4]
ISB4
Standby Current
(One Port CMOS Level)
One Port CEL or CER ≥ VCC – 0.2V,
Com’l
Ind.
90
90
mA
VIN ≥ VCC – 0.2V or VIN ≤ 0.2V,
100
100
[4]
Active Port Outputs, f = fMAX
Capacitance[5]
Parameter
Description
Test Conditions
Max.
Unit
CIN
Input Capacitance
Output Capacitance
TA = 25°C, f = 1 MHz,
VCC = 5.0V
10
10
pF
pF
COUT
Figure 3. AC Test Loads and Waveforms
5V
R1 = 893Ω
R1 = 347Ω
RTH = 250Ω
RTH = 250Ω
OUTPUT
C = 30 pF
OUTPUT
OUTPUT
C = 5 pF
C = 30 pF
VX
(c) Three-State Delay (Load 3)
VTH = 1.4V
(a) Normal Load (Load 1)
(b) Thévenin Equivalent (Load 1)
ALL INPUT PULSES
3.0V
90%
90%
10%
10%
GND
≤3 ns
≤ 3 ns
Note
5. Tested initially and after any design or process changes that may affect these parameters.
Document #: 38-06038 Rev. *D
Page 4 of 12
[+] Feedback
CY7C135, CY7C135A
CY7C1342
Switching Characteristics Over the Operating Range[6]
7C135-25
7C135A-25
7C1342-25
7C135-15
7C135-20
7C135-35
7C135-55
7C1342-15 7C1342-20
7C1342-35 7C1342-55
Parameter
Description
Unit
Min Max Min Max Min Max Min Max Min Max
Read Cycle
tRC
Read Cycle Time
15
3
20
3
25
3
35
3
55
3
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
tAA
Address to Data Valid
Output Hold From Address Change
CE LOW to Data Valid
OE LOW to Data Valid
OE Low to Low Z
15
20
25
35
55
tOHA
tACE
tDOE
tLZOE
15
10
20
13
25
15
35
20
55
25
[7,8,9]
[7,8,9]
3
3
0
3
3
0
3
3
0
3
3
0
3
3
0
tHZOE
OE HIGH to High Z
10
10
15
13
13
20
15
15
25
20
20
35
25
25
55
[7,8,9]
tLZCE
CE LOW to Low Z
[7,8,9]
tHZCE
CE HIGH to High Z
[9]
tPU
CE LOW to Power Up
CE HIGH to Power Down
[9]
tPD
Write Cycle
tWC
tSCE
tAW
Write Cycle Time
15
12
12
2
20
15
15
2
25
20
20
2
35
30
30
2
55
50
50
2
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
CE LOW to Write End
Address Setup to Write End
Address Hold from Write End
Address Setup to Write Start
Write Pulse Width
tHA
tSA
0
0
0
0
0
tPWE
tSD
12
10
0
15
13
0
20
15
0
25
15
0
50
25
0
Data Setup to Write End
Data Hold from Write End
R/W LOW to High Z
tHD
[8,9]
tHZWE
10
13
15
20
25
[8,9]
tLZWE
R/W HIGH to Low Z
3
3
3
3
3
[10]
tWDD
Write Pulse to Data Delay
Write Data Valid to Read Data Valid
30
25
40
30
50
30
60
35
70
40
[10]
tDDD
Semaphore Timing[11]
tSOP
SEM Flag Update Pulse
(OE or SEM)
10
10
10
15
15
ns
tSWRD
tSPS
SEM Flag Write to Read Time
SEM Flag Contention Window
5
5
5
5
5
5
5
5
5
5
ns
ns
Notes
6. Test conditions assume signal transition time of 3 ns or less, timing reference levels of 1.5V, input pulse levels of 0 to 3.0V, and output loading of the specified I /I
OL OH
and 30 pF load capacitance.
7. At any given temperature and voltage condition for any given device, t
8. Test conditions used are Load 3.
is less than t
and t
is less than t
.
LZOE
HZCE
LZCE
HZOE
9. This parameter is guaranteed but not tested.
10. For information on port-to-port delay through RAM cells from writing port to reading port, refer to Figure 6.
11. Semaphore timing applies only to CY7C1342.
Document #: 38-06038 Rev. *D
Page 5 of 12
[+] Feedback
CY7C135, CY7C135A
CY7C1342
Switching Waveforms
Figure 4. Read Cycle No. 1[12,13]
Either Port Address Access
t
RC
ADDRESS
t
AA
t
OHA
DATA OUT
PREVIOUS DATA VALID
DATA VALID
Figure 5. Read Cycle No. 2[12,14]
Either Port CE/OE Access
[11]
or CE
OE
SEM
t
HZCE
t
ACE
t
HZOE
t
DOE
t
LZOE
t
LZCE
DATA VALID
DATA OUT
t
PU
t
PD
ICC
ISB
Figure 6. Read Timing with Port-to-Port[15]
t
wc
ADDRESSR
R/WR
MATCH
t
PWE
t
t
SD
HD
DATA
INR
VALID
ADDRESSL
MATCH
t
DDD
DATA
OUTL
VALID
t
WDD
Notes
12. R/W is HIGH for read cycle.
13. Device is continuously selected, CE = V and OE = V .
IL
IL
14. Address valid prior to or coincident with CE transition LOW.
15. CE = CE =LOW; R/W = HIGH
L
R
L
Document #: 38-06038 Rev. *D
Page 6 of 12
[+] Feedback
CY7C135, CY7C135A
CY7C1342
Switching Waveforms (continued)
Figure 7. Write Cycle No. 1: OE Three-States Data I/Os (Either Port)[16, 17, 18]
t
WC
ADDRESS
[11]
t
SCE
SEM
OR CE
t
t
HA
AW
t
PWE
R/W
t
SA
t
t
HD
SD
DATA
IN
DATA VALID
OE
t
t
HZOE
LZOE
HIGH IMPEDANCE
DATA
OUT
Figure 8. Write Cycle No. 2: R/W Three-States Data I/Os (Either Port)[17, 19]
t
WC
ADDRESS
t
t
HA
SCE
[11]
SEM
OR
CE
t
AW
t
SA
t
PWE
R/W
t
t
HD
SD
DATA VALID
DATA
IN
t
t
LZWE
HZWE
HIGH IMPEDANCE
DATA
OUT
Notes
16. The internal write time of the memory is defined by the overlap of CE or SEM LOW and R/W LOW. Both signals must be LOW to initiate a write and either signal
can terminate a write by going HIGH. The data input setup and hold timing should be referenced to the rising edge of the signal that terminates the write.
17. R/W must be HIGH during all address transactions.
18. If OE is LOW during a R/W controlled write cycle, the write pulse width must be the larger of t
or (t
+ t ) to allow the I/O drivers to turn off and data
PWE
HZWE SD
to be placed on the bus for the required t . If OE is HIGH during a R/W controlled write cycle (as in this example), this requirement does not apply and the
SD
write pulse can be as short as the specified t
.
PWE
19. Data I/O pins enter high impedance when OE is held LOW during write.
Document #: 38-06038 Rev. *D
Page 7 of 12
[+] Feedback
CY7C135, CY7C135A
CY7C1342
Switching Waveforms (continued)
Figure 9. Semaphore Read After Write Timing, Either Side (CY7C1342 only)[20]
t
AA
t
OHA
A0–A2
VALID ADDRESS
VALID ADDRESS
t
AW
t
ACE
t
SEM
HA
t
SCE
t
SOP
t
SD
I/O
0
DATA VALID
DATA
VALID
IN
OUT
t
HD
t
SA
t
PWE
R/W
OE
t
t
DOE
SWRD
t
SOP
WRITE CYCLE
READ CYCLE
Figure 10. Timing Diagram of Semaphore Contention (CY7C1342 Only)[21, 22, 23]
A0L–A2L
MATCH
R/WL
SEML
tSPS
A0R–A2R
MATCH
R/WR
SEMR
Notes
20. CE = HIGH for the duration of the above timing (both write and read cycle).
21. I/O = I/O = LOW (request semaphore); CE = CE = HIGH.
0R
0L
R
L
22. Semaphores are reset (available to both ports) at cycle start.
23. If t is violated, it is guaranteed that only one side gains access to the semaphore.
SPS
Document #: 38-06038 Rev. *D
Page 8 of 12
[+] Feedback
CY7C135, CY7C135A
CY7C1342
now only be modified by the side showing a zero (the left port in
this case). If the left port now relinquishes control by writing a one
to the semaphore, the semaphore is set to one for both sides.
However, if the right port had requested the semaphore (written
a zero) while the left port had control, the right port would immedi-
ately own the semaphore. Table 2 shows sample semaphore
operations.
Architecture
The CY7C135/135A consists of an array of 4K words of 8 bits
each of dual-port RAM cells, I/O and address lines, and control
signals (CE, OE, R/W). Two semaphore control pins exist for the
CY7C1342 (SEML/R).
Functional Description
When reading a semaphore, all eight data lines output the
semaphore value. The read value is latched in an output register
to prevent the semaphore from changing state during a write
from the other port. If both ports request a semaphore control by
writing a 0 to a semaphore within tSPS of each other, it is
guaranteed that only one side gains access to the semaphore.
Write Operation
Data must be set up for a duration of tSD before the rising edge
of R/W to guarantee a valid write. Because there is no on-chip
arbitration, the user must be sure that a specific location is not
accessed simultaneously by both ports or erroneous data could
result. A write operation is controlled by either the OE pin (see
Figure 7) or the R/W pin (see Figure 8). Data can be written
Initialization of the semaphore is not automatic and must be reset
during initialization program during power up. All semaphores on
both sides should have a one written into them at initialization
from both sides to assure that they are free when needed.
t
HZOE after the OE is deasserted or tHZWE after the falling edge
of R/W. Required inputs for write operations are summarized in
Table 1. Non-Contending Read/Write
Table 1.
Inputs
Outputs
If a location is being written to by one port and the opposite port
attempts to read the same location, a port-to-port flowthrough
delay is met before the data is valid on the output. Data is valid
on the port wishing to read the location tDDD after the data is
presented on the writing port.
Operation
Power Down
CE R/W OE SEM I/O0 – I/O7
H
H
X
H
L
X
H
X
L
X
L
H
L
High Z
Data Out
High Z
Read Semaphore
I/O Lines Disabled
Write to Semaphore
Read
H
X
L
X
L
Read Operation
Data In
Data Out
Data In
When reading the device, the user must assert both the OE and
CE pins. Data is available tACE after CE or tDOE after OE are
asserted. If the user of the CY7C1342 wishes to access a
semaphore, the SEM pin must be asserted instead of the CE pin.
Required inputs for read operations are summarized in Table 1.
H
L
H
H
L
L
X
X
Write
L
X
Illegal Condition
Table 2. Semaphore Operation Example
Semaphore Operation
I/O0-7 I/O0-7
Function
The CY7C1342 provides eight semaphore latches, which are
separate from the dual port memory locations. Semaphores are
used to reserve resources which are shared between the two
ports. The state of the semaphore indicates that a resource is in
use. For example, if the left port wants to request a given
resource, it sets a latch by writing a zero to a semaphore location.
The left port then verifies its success in setting the latch by
reading it. After writing to the semaphore, SEM or OE must be
deasserted for tSOP before attempting to read the semaphore.
The semaphore value is available tSWRD + tDOE after the rising
edge of the semaphore write. If the left port was successful
(reads a zero), it assumes control over the shared resource,
otherwise (reads a one) it assumes the right port has control and
continues to poll the semaphore. When the right side has relin-
quished control of the semaphore (by writing a one), the left side
succeeds in gaining control of the semaphore. If the left side no
longer requires the semaphore, a one is written to cancel its
request.
Status
Left Right
No action
1
0
1
1
Semaphore free
Left port writes
semaphore
Left port obtains
semaphore
Right port writes 0 to
semaphore
0
1
1
0
1
1
1
0
1
1
0
0
1
1
0
1
1
1
Right side is denied
access
Left port writes 1 to
semaphore
Right port is granted
access to Semaphore
Left port writes 0 to
semaphore
No change. Left port is
denied access
Right port writes 1 to
semaphore
Left port obtains
semaphore
Left port writes 1 to
semaphore
No port accessing
semaphore address
Right port writes 0 to
semaphore
Right port obtains
semaphore
Semaphores are accessed by asserting SEM LOW. The SEM
pin functions as a chip enable for the semaphore latches. CE
must remain HIGH during SEM LOW. A0–2 represents the
semaphore address. OE and R/W are used in the same manner
as a normal memory access. When writing or reading a
semaphore, the other address pins have no effect.
Right port writes 1 to
semaphore
No port accessing
semaphore
Left port writes 0 to
semaphore
Left port obtains
semaphore
When writing to the semaphore, only I/O0 is used. If a 0 is written
to the left port of an unused semaphore, a one appears at the
same semaphore address on the right port. That semaphore can
Left port writes 1 to
semaphore
No port accessing
semaphore
Document #: 38-06038 Rev. *D
Page 9 of 12
[+] Feedback
CY7C135, CY7C135A
CY7C1342
Typical DC and AC Characteristics
NORMALIZED SUPPLY CURRENT
vs. AMBIENT TEMPERATURE
OUTPUT SOURCE CURRENT
vs. OUTPUT VOLTAGE
NORMALIZED SUPPLY CURRENT
vs. SUPPLY VOLTAGE
140
120
100
80
1.4
1.2
1.0
1.2
1.0
ISB
ICC
ISB3
0.8
0.6
0.4
0.8
0.6
0.4
VCC = 5.0V
TA = 25°C
VCC = 5.0V
VIN = 5.0V
60
40
0.2
0.6
0.2
0.0
20
0
ICC
4.5
SUPPLY VOLTAGE (V)
4.0
5.0
5.5
6.0
–55
25
125
0
1.0
2.0
3.0
4.0 5.0
AMBIENT TEMPERATURE (°C)
OUTPUT VOLTAGE (V)
NORMALIZED ACCESS TIME
vs. AMBIENT TEMPERATURE
OUTPUT SINK CURRENT
vs. OUTPUT VOLTAGE
NORMALIZED ACCESS TIME
vs. SUPPLY VOLTAGE
1.2
1.1
100
90
1.10
1.05
TA = 25°C
80
70
1.0
0.9
V
CC = 5.0V
1.00
0.95
VCC = 5.0V
60
50
T
A = 25°C
0.8
–55
0.0
1.0
2.0 3.0
4.0 5.0
25
125
4.0
4.5
5.0
5.5
6.0
AMBIENT TEMPERATURE (°C)
OUTPUT VOLTAGE (V)
SUPPLY VOLTAGE (V)
TYPICAL POWER-ON CURRENT
vs. SUPPLY VOLTAGE
TYPICAL ACCESS TIME CHANGE
vs. OUTPUT LOADING
NORMALIZED ICC vs. CYCLE TIME
1.25
20.0
1.0
V
CC = 5.0V
TA = 25°C
VIN = 5.0V
15.0
10.0
0.75
0.50
1.0
0.75
VCC = 4.5V
5.0
0
0.25
0.0
TA = 25°C
0.50
10
20
30
40
50
0
200 400 600 800 1000
CAPACITANCE (pF)
0
1.0
2.0
3.0
4.0 5.0
CYCLE FREQUENCY (MHz)
SUPPLY VOLTAGE (V)
Document #: 38-06038 Rev. *D
Page 10 of 12
[+] Feedback
CY7C135, CY7C135A
CY7C1342
Ordering Information
4K x8 Dual-Port SRAM
Speed
Package
Name
Operating
Range
(ns)
Ordering Code
Package Type
15
CY7C135–15JC
CY7C135-15JXC
CY7C135–20JC
CY7C135–25JC
CY7C135-25JXC
CY7C135A–25JI
CY7C135–25JXI
CY7C135–35JC
CY7C135–35JI
CY7C135–55JC
CY7C135–55JI
J69
J69
J69
J69
J69
J69
J69
J69
J69
J69
J69
52-Pin Plastic Leaded Chip Carrier
Commercial
52-Pin Pb-Free Plastic Leaded Chip Carrier
52-Pin Plastic Leaded Chip Carrier
52-Pin Plastic Leaded Chip Carrier
52-Pin Pb-Free Plastic Leaded Chip Carrier
52-Pin Plastic Leaded Chip Carrier
52-Pin Pb-Free Plastic Leaded Chip Carrier
52-Pin Plastic Leaded Chip Carrier
52-Pin Plastic Leaded Chip Carrier
52-Pin Plastic Leaded Chip Carrier
52-Pin Plastic Leaded Chip Carrier
20
25
Commercial
Commercial
Industrial
35
55
Commercial
Industrial
Commercial
Industrial
Package Diagram
Figure 11. 52-Pin Pb-Free Plastic Leaded Chip Carrier J69
51-85004-*A
Document #: 38-06038 Rev. *D
Page 11 of 12
[+] Feedback
CY7C135, CY7C135A
CY7C1342
Document History Page
Document Title: CY7C135/CY7C135A/CY7C1342 4K x 8 Dual Port Static RAM and 4K x 8 Dual Port SRAM with Semaphores
Document Number: 38-06038
Orig. of
Change
Submission
Date
Rev.
ECN No.
Description of Change
**
110181
122288
236763
393413
SZV
RBI
10/21/01
12/27/02
Change from Spec number: 38-00541 to 38-06038
*A
*B
*C
Power up requirements added to Maximum Ratings Information
YDT
YIM
SEE ECN Removed cross information from features section
See ECN Added Pb-Free Logo
Added Pb-Free parts to ordering information:
CY7C135-15JXC, CY7C135-25JXC
*D
2623540
VKN/PYRS
12/17/08
Added CY7C135A parts
Removed CY7C1342 from the ordering information table
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at cypress.com/sales.
Products
PSoC
PSoC Solutions
General
psoc.cypress.com/solutions
psoc.cypress.com/low-power
psoc.cypress.com/precision-analog
psoc.cypress.com/lcd-drive
psoc.cypress.com/can
psoc.cypress.com
clocks.cypress.com
wireless.cypress.com
memory.cypress.com
image.cypress.com
Low Power/Low Voltage
Precision Analog
LCD Drive
Clocks & Buffers
Wireless
Memories
CAN 2.0b
Image Sensors
USB
psoc.cypress.com/usb
© Cypress Semiconductor Corporation, 2001-2008. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of
any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for
medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as
critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems
application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Document #: 38-06038 Rev. *D
Revised December 09, 2008
Page 12 of 12
All products and company names mentioned in this document may be the trademarks of their respective holders.
[+] Feedback
相关型号:
©2020 ICPDF网 联系我们和版权申明