CY7C63101A-QXC [CYPRESS]
Universal Serial Bus Microcontroller; 通用串行总线的微控制器
| 型号： | CY7C63101A-QXC |
| 厂家： | 
CYPRESS |
| 描述： | Universal Serial Bus Microcontroller |
| 文件： | 总25页 (文件大小：500K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
CY7C63001A
CY7C63101A
Universal Serial Bus Microcontroller
—Integrated USB transceiver
1.0
Features
—Up to 16 Schmitt trigger I/O pins with internal pull-up
• Low-cost solution for low-speed USB peripherals such
as mouse, joystick, and gamepad
—Up to eight I/O pins with LED drive capability
• USB Specification Compliance
—Special purpose I/O mode supports optimization of
photo transistor and LED in mouse application
— Conforms to USB 1.5-Mbps Specification,
Version 1.1
—Maskable Interrupts on all I/O pins
• 8-bit free-running timer
— Supports one device address and two endpoints
(one control endpoint and one data endpoint)
• Watchdog timer (WDT)
• 8-bit RISC microcontroller
— Harvard architecture
• Internal power-on reset (POR)
• Instant-On Now™ for Suspend and Periodic Wake-up
Modes
— 6-MHz external ceramic resonator
— 12-MHz internal operation
— USB optimized instruction set
• Internal memory
• Improved output drivers to reduce EMI
• Operating voltage from 4.0V to 5.25 VDC
• Operating temperature from 0–70°C
• Available in space saving and low-cost 20-pin PDIP,
20-pin SOIC, and 24-pin QSOP packages
— 128 bytes of RAM
— 4 Kbytes of EPROM
• Industry-standard programmer support
Logic Block Diagram
6-MHz
CERAMIC RESONATOR
R/CEXT
OSC
INSTANT-ON
NOW™
RAM
128-Byte
8-bit
Timer
8-bit
RISC
core
EPROM
2/4 KByte
Power-
on Reset
USB
Engine
PORT
PORT
Interrupt
Controller
0
1
Watch
Dog
Timer
D+,D–
P0.0–P0.7
P1.0–P1.7
VCC/VSS
Cypress Semiconductor Corporation
Document #: 38-08026 Rev. *A
•
3901 North First Street
•
San Jose, CA 95134
•
408-943-2600
Revised October 5, 2004
CY7C63001A
CY7C63101A
2.0
Pin Configurations
(Top View)
24-pin
SOIC/QSOP
20-pin
CY7C63101A
DIE
DIP/SOIC
P0.4
P0.5
P0.6
P0.7
P1.1
P1.3
P1.5
P1.7
D+
P0.0
P0.1
P0.2
P0.3
P1.0
P1.2
P1.4
P1.6
1
2
3
4
5
6
7
8
24
23
22
21
20
19
18
17
16
15
P0.4
19 P0.5
P0.0
P0.1
P0.2
P0.3
P1.0
P1.2
20
1
2
3
4
5
6
7
8
9
4
3 2 1 24 23 22 21
5
20
19
18
17
P0.6
P0.7
P1.1
P1.3
D+
18
17
16
15
14
13
6
7
8
V
SS
D–
V
PP
V
V
12
11
9
CEXT
XTALIN 10
CC
SS
9
10 11 12 13 14 15 16
D–
XTALOUT
V
10
11
12
PP
V
14
13
CC
CEXT
XTALIN
XTALOUT
pins in Port 1 are equipped with programmable drivers strong
enough to drive LEDs. The GPIO ports feature low EMI
emissions as a result of controlled rise and fall times and
unique output driver circuits. The Cypress microcontrollers
have a range of GPIOs to fit various applications; the
CY7C6300XA has twelve GPIOs and the CY7C6310XA has
sixteen GPIOs. Notice that each part has eight ‘low-current’
ports (Port 0) with the remaining ports (Port 1) being ‘high-
current’ ports.
3.0
Functional Overview
The CY7C630/101A is a family of 8-bit RISC One Time
Programmable (OTP) microcontrollers with a built-in 1.5-Mbps
USB Serial Interface Engine (SIE). The microcontroller
features 35 instructions that are optimized for USB applica-
tions. In addition, the microcontroller features 128 bytes of
internal RAM and four Kbytes of program memory space. The
Cypress USB Controller accepts a 6-MHz ceramic resonator
as its clock source. This clock signal is doubled within the chip
to provide a 12- MHz clock for the microprocessor.
The 12-GPIO CY7C6300XA is available in 20-pin PDIP (-PC)
and 20-pin SOIC (-SC) packages. The 26-GPIO
CY7C6310XA is available in 24-pin QSOP (-QC) package.
The microcontroller features two ports of up to sixteen general
purpose I/Os (GPIOs). Each GPIO pin can be used to
generate an interrupt to the microcontroller. Additionally, all
4.0
Pin Definitions
Name
P0.0
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I
20-Pin
1
24-pin
1
Die Pad #
Description
1
2
Port 0 bit 0
P0.1
2
2
Port 0 bit 1
P0.2
3
3
3
Port 0 bit 2
P0.3
4
4
4
Port 0 bit 3
P0.4
20
19
18
17
5
24
23
22
21
5
24
23
22
21
5
Port 0 bit 4
P0.5
Port 0 bit 5
P0.6
Port 0 bit 6
P0.7
Port 0 bit 7
P1.0
Port 1 bit 0
P1.1
16
6
20
6
20
6
Port 1 bit 1
P1.2
Port 1 bit 2
P1.3
15
–
19
7
19
7
Port 1 bit 3
P1.4
Port 1 bit 4
P1.5
–
18
8
18
8
Port 1 bit 5
P1.6
–
Port 1 bit 6
P1.7
–
17
12
13
17
12
13
Port 1 bit 7
XTALIN
XTALOUT
10
11
Ceramic resonator in
Ceramic resonator out
O
Document #: 38-08026 Rev. *A
Page 2 of 25
CY7C63001A
CY7C63101A
4.0
Pin Definitions (continued)
Name
CEXT
I/O
20-Pin
24-pin
Die Pad #
Description
I/O
9
11
11
Connects to external R/C timing circuit for optional
‘suspend’ wakeup
D+
D–
I/O
I/O
–
14
13
8
16
15
10
16
15
10
USB data+
USB data–
VPP
Programming voltage supply, tie to ground during normal
operation
VCC
VSS
–
–
12
7
14
9
14
9
Voltage supply
Ground
5.0
Pin Description
Name
Description
VCC
One pin. Connects to the USB power source or to a nominal 5V power supply. Actual VCC range can vary
between 4.0V and 5.25V.
VSS
VPP
One pin. Connects to ground.
One pin. Used in programming the on-chip EPROM. This pin should be tied to ground during normal opera-
tions.
XTALIN
One pin. Input from an external ceramic resonator.
XTALOUT
One pin. Return path for the ceramic resonator (leave unconnected if driving XTALIN from an external
oscillator).
P0.0–P0.7,
P1.0–P1.7
Sixteen pins. P0.0–P0.7 are the 8 I/O lines in Port 0. P1.0–P1.7 are the 8 I/O lines in Port 1. P1.0–P1.3 are
supported in the CY7C6300XA. All I/O pins include bit-programmable pull-up resistors. However, the sink
current of each pin can be programmed to one of sixteen levels. Besides functioning as GPIO lines, each
pin can be programmed as an interrupt input. The interrupt is edge-triggered, with programmable polarity.
D+, D–
CEXT
Two pins. Bidirectional USB data lines. An external pull-up resistor must be connected between the D pin
and VCC to select low-speed USB operation.
One pin. Open-drain output with Schmitt trigger input. The input is connected to a rising edge-triggered
interrupt. CEXT may be connected to an external RC to generate a wake-up from Suspend mode. See
Section 6.4.
6.1.1
Program Memory Organization
6.0
Functional Description
The CY7C63001A and CY7C63101A each offer 4 Kbytes of
EPROM. The program memory space is divided into two
functional groups: interrupt vectors and program code.
The Cypress CY7C630/101A USB microcontrollers are
optimized for human-interface computer peripherals such as
a mouse, joystick, and gamepad. These USB microcontrollers
conform to the low-speed (1.5 Mbps) requirements of the USB
Specification version 1.1. Each microcontroller is a self-
contained unit with: a USB interface engine, USB transceivers,
an 8-bit RISC microcontroller, a clock oscillator, timers, and
program memory. Each microcontroller supports one USB
device address and two endpoints.
The interrupt vectors occupy the first 16 bytes of the program
space. Each vector is 2 bytes long. After a reset, the Program
Counter points to location zero of the program space. Figure
6-1 shows the organization of the Program Memory Space.
6.1.2
Security Fuse Bit
The 6-MHz clock is doubled to 12 MHz to drive the microcon-
troller. A RISC architecture with 35 instructions provides the
best balance between performance and product cost.
The Cypress USB microcontroller includes a security fuse bit.
When the security fuse is programmed, the EPROM program
memory outputs 0xFF to the EPROM programmer, thus
protecting the user’s code.
6.1
Memory Organization
The memory in the USB Controller is organized into user
program memory in EPROM space and data memory in SRAM
space.
Document #: 38-08026 Rev. *A
Page 3 of 25
CY7C63001A
CY7C63101A
after reset
PC
Address
0x0000
Reset Vector
0x0002
0x0004
0x0006
0x0008
0x000A
0x000C
0x000E
0x0010
Interrupt Vector – 128 µs
Interrupt Vector – 1.024 ms
Interrupt Vector – USB Endpoint 0
Interrupt Vector – USB Endpoint 1
Reserved
Interrupt Vector – GPIO
Interrupt Vector – Cext
On-chip program Memory
0x07FF
2K ROM (CY7C63000A, CY7C63100A)
0x0FFF
4K ROM (CY7C63001A, CY7C63101A)
Figure 6-1. Program Memory Space
6.1.3
Data Memory Organization
The DSP pre-decrements by one whenever a PUSH
instruction is executed and it increments by one after a POP
instruction is used. The default value of the DSP after reset is
0x00, which would cause the first PUSH to write into USB
FIFO space for Endpoint 1. Therefore, the DSP should be
mapped to a location such as 0x70 before initiating any data
stack operations. Refer to the Reset section for more infor-
mation about DSP remapping after reset. Figure 6-2 illustrates
the Data Memory Space.
The USB Controller includes 128 bytes of data RAM. The
upper 16 bytes of the data memory are used as USB FIFOs
for Endpoint 0 and Endpoint 1. Each endpoint is associated
with an 8-byte FIFO.
The USB controller includes two pointers into data RAM, the
Program Stack Pointer (PSP) and the Data Stack Pointer
(DSP). The value of PSP after reset is 0x00. The PSP incre-
ments by two whenever a CALL instruction is executed and it
decrements by two whenever a RET instruction is used.
Document #: 38-08026 Rev. *A
Page 4 of 25
CY7C63001A
CY7C63101A
after reset
DSP
Address
0x00
PSP
0x02
0x04
user
firmware
0x70
USB FIFO – Endpoint 0
USB FIFO – Endpoint 1
DSP
0x77
0x78
0x7F
Figure 6-2. Data Memory Space
6.2
I/O Register Summary
I/O registers are accessed via the I/O Read (IORD) and I/O
Write (IOWR, IOWX) instructions.
Table 6-1. I/O Register Summary
Register Name I/O Address
Read/Write
R/W
R/W
W
Function
General purpose I/O Port (low current)
General purpose I/O Port (high current)
Interrupt enable for Port 0 pins
Interrupt enable for Port 1 pins
Pull-up resistor control for Port 0 pins
Pull-up resistor control for Port 1 pins
USB Endpoint 0 transmit configuration
USB Endpoint 1 transmit configuration
USB device address
Page
Figure 6-8
Figure 6-9
Figure 6-17
Figure 6-18
Figure 6-11
Figure 6-12
Figure 6-22
Figure 6-23
Figure 6-20
Figure 6-24
Figure 6-21
Figure 6-15
Figure 6-4
Figure 6-5
Figure 6-6
P0 Data
P1 Data
P0 IE
0x00
0x01
0x04
P1 IE
0x05
W
P0 Pull-up
P1 Pull-up
EP0 TX Config.
EP1 TX Config.
USB DA
USB SCR
EP0 RX Status
GIE
0x08
W
0x09
W
0x10
R/W
R/W
R/W
R/W
R/W
R/W
W
0x11
0x12
0x13
USB status and control
0x14
USB Endpoint 0 receive status
Global Interrupt Enable
0x20
WDT
0x21
Watchdog Timer clear
Cext
0x22
R/W
R
External R-C Timing circuit control
Free-running timer
Timer
0x23
P0 Isink
0x30-0x37
W
Input sink current control for Port 0 pins. There is one Figure 6-13
Isink register for each pin. Address of the Isink register
for pin 0 is located at 0x30 and the register address for
pin 7 is located at 0x37.
Document #: 38-08026 Rev. *A
Page 5 of 25
CY7C63001A
CY7C63101A
Table 6-1. I/O Register Summary (continued)
Register Name I/O Address
Read/Write
Function
Page
P1 Isink
0x38-0x3F
W
Input sink current control for Port 1 pins. There is one Figure 6-13
Isink register for each pin. Address of the Isink register
for pin 0 is located at 0x38 and the register address for
pin 7 is located at 0x3F. The number of Port 1 pins
depends on package type.
SCR
0xFF
R/W
Processor status and control register
Figure 6-3
The occurrence of a reset is recorded in the Status and Control
Register located at I/O address 0xFF (Figure 6-3). Reading
and writing this register are supported by the IORD and IOWR
instructions. Bits 1, 2, and 7 are reserved and must be written
as zeros during a write. During a read, reserved bit positions
should be ignored. Bits 4, 5, and 6 are used to record the
occurrence of POR, USB, and WDR Reset respectively. The
firmware can interrogate these bits to determine the cause of
a reset. If a Watchdog Reset occurs, firmware must clear the
WDR bit (bit 6) in the Status and Control Register to re-enable
the USB transmitter (please refer to the Watchdog Reset
section for further details). Bit 0, the “Run” control, is set to 1
at POR. Clearing this bit stops the microcontroller (firmware
normally should not clear this bit). Once this bit is set to LOW,
only a reset can set this bit HIGH.
6.3
Reset
The USB Controller supports three types of resets. All
registers are restored to theirWatchdog default states during a
reset. The USB Device Address is set to 0 and all interrupts
are disabled. In addition, the Program Stack Pointer (PSP) is
set to 0x00 and the Data Stack Pointer (DSP) is set to 0x00.
The user should set the DSP to a location such as 0x70 to
reserve 16 bytes of USB FIFO space. The assembly instruc-
tions to do so are:
MOV A, 70h
instead of 6F because the dsp is
; always decremented by 1 before the
data transfer of the PUSH instruction occurs
; Move 70 hex into Accumulator, use 70
SWAP A, DSP
; Move Accumulator value into dsp
The three reset types are:
1. Power-On Reset (POR)
2. Watchdog Reset (WDR)
3. USB Reset
The microcontroller resumes execution from ROM address
0x00 after a reset unless the Suspend bit (bit 3) of the Status
and Control Register is set. Setting the Suspend bit stops the
clock oscillator and the interrupt timers and powers down the
microcontroller. The detection of any USB activity, the occur-
rence of a GPIO Interrupt, or the occurrence of the Cext
Interrupt terminates the suspend condition.
b7
b6
b5
b4
b3
b2
b1
b0
Reserved
WDR
USBR
POR
SUSPEND
Reserved
Reserved
RUN
R/W
0
R/W
0
R/W
1
R/W
0
R/W
1
0
0
0
Figure 6-3. Status and Control Register (SCR – Address 0xFF)
6.3.1
Power-On Reset
suspended mode at the end of POR to conserve power (the
clock oscillator, the timers, and the interrupt logic are turned
off in suspend mode). After POR, only a non-idle USB Bus
state terminates the suspend mode. The microcontroller then
begins execution from ROM address 0x00.
Power-On Reset (POR) occurs every time the power to the
device is switched on. Bit 4 of the Status and Control Register
is set to record this event (the register contents are set to
00011001 by the POR). The USB Controller is placed in
Document #: 38-08026 Rev. *A
Page 6 of 25
CY7C63001A
CY7C63101A
7.168 to
8.192 ms
8.192 ms
Last write to
Watchdog Timer
Register
No write to WDT
register, so WDR
goes HIGH
Execution begins at
Reset Vector 0x00
Figure 6-4. Watchdog Reset
6.3.2
Watchdog Reset (WDR)
register. All logic blocks in the device are turned off except the
USB receiver, the GPIO interrupt logic, and the Cext interrupt
logic. The clock oscillator and the free-running and Watchdog
timers are shut down.
The Watchdog Timer Reset (WDR) occurs when the Most
Significant Bit of the 4-bit Watchdog Timer Register transitions
from LOW to HIGH. Writing any value to the write-only
Watchdog Restart Register at 0x21 clears the timer (firmware
should periodically write to the Watchdog Restart Register in
the ‘main loop’ of firmware). The Watchdog timer is clocked by
a 1.024-ms clock from the free-running timer. If 8 clocks occur
between writes to the timer, a WDR occurs and bit 6 of the
Status and Control Register is set to record the event. A
Watchdog Timer Reset lasts for 8.192 ms, at which time the
microcontroller begins execution at ROM address 0x00. The
USB transmitter is disabled by a Watchdog Reset because the
USB Device Address Register is cleared (otherwise, the USB
Controller would respond to all address 0 transactions). The
transmitter remains disabled until the WDR bit (bit 6) in the
Status and Control Register is reset to 0 by firmware.
The suspend mode is terminated when one of the following
three conditions occur:
1. USB activity
2. A GPIO interrupt
3. Cext interrupt
The clock oscillator, GPIO, and timers restart immediately
upon exiting suspend mode. The USB engine and microcon-
troller return to a fully functional state no more than 256 µs
later. Before servicing any interrupt requests, the microcon-
troller executes the instruction following the I/O write that
placed the device into suspend mode.
Both the GPIO interrupt and the Cext interrupt allow the USB
Controller to wake-up periodically and poll potentiometers,
optics, and other system components while maintaining a very
low average power consumption. The Cext Interrupt is
preferred for lowest power consumption.
6.3.3
USB Bus Reset
The USB Controller recognizes a USB Reset when a Single
Ended Zero (SE0) condition persists for at least 8–16 µs (the
Reset may be recognized for an SE0 as short as 8 µs, but it is
always recognized for an SE0 longer than 16 µs). SE0 is the
condition in which both the D+ line and the D– line are LOW.
Bit 5 of the Status and Control Register is set to record this
event. If the USB reset happens while the device is
suspended, the suspend condition is cleared and the clock
oscillator is restarted. However, the microcontroller is not
released until the USB reset is removed.
For Cext to generate an “Instant-on” interrupt, the pin must be
connected to ground with an external capacitor and connected
to VCC with an external resistor. A “0” is written to the Cext
register located at I/O address 0x22 to discharge the capacitor.
Then, a “1” is written to disable the open-drain output driver. A
Schmitt trigger input circuit monitors the input and generates
a wake-up interrupt when the input voltage rises above the
input threshold. By changing the values of the external resistor
and capacitor, the user can fine tune the charge rate of the R-
C timing circuit. The format of the Cext register is shown in
Figure 6-5. Reading the register returns the value of the Cext
pin. During a reset, the Cext pin is HIGH.
6.4
Instant-on Feature (Suspend Mode)
The USB Controller can be placed in a low-power state by
setting the Suspend bit (bit 3) of the Status and Control
b7
b6
b5
b4
b3
b2
b1
b0
CEXT
R/W
1
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
0
0
0
0
0
0
0
Figure 6-5. The Cext Register (Address 0x22)
Document #: 38-08026 Rev. *A
Page 7 of 25
CY7C63001A
CY7C63101A
mode is entered. Figure 6-6 illustrates the format of this
register and Figure 6-7 is its block diagram.
6.5
On-Chip Timer
The USB Controller is equipped with a free-running timer
driven by a clock one-sixth the resonator frequency. Bits 0
through 7 of the counter are readable from the read-only Timer
Register located at I/O address 0x23. The Timer Register is
cleared during a Power-On Reset and whenever Suspend
With a 6 MHz resonator, the timer resolution is 1 µs.
The timer generates two interrupts: the 128-µs interrupt and
the 1.024-ms interrupt.
Figure 6-6. Timer Register (Address 0x23)
b4 b3
T.4 T.3
b7
T.7
R
b6
T.6
R
b5
T.5
R
b2
T.2
R
b1
T.1
R
b0
T.0
R
R
0
R
0
0
0
0
0
0
0
1.024-ms interrupt
128- s interrupt
m
9
7
8
1
0
6
3
5
4
2
Resonator Clock/6
8
To Timer Register
Figure 6-7. Timer Block Diagram
Port 0 data register is located at I/O address 0x00 while the
Port 1 data register is located at I/O address 0x01. The
contents of both registers are set HIGH during a reset. Refer
to Figures 6-8 and 6-9 for the formats of the data registers. In
addition to supporting general input/output functions, each I/O
line can trigger an interrupt to the microcontroller. Please refer
to the interrupt section for more details.
6.6
General Purpose I/O Ports
Interface with peripherals is conducted via as many as 16
GPIO signals. These signals are divided into two ports: Port 0
and Port 1. Port 0 contains eight lines (P0.0–P0.7) and Port 1
contains up to eight lines (P1.0–P1.7). The number of external
I/O pins depends on the package type. Both ports can be
accessed by the IORD, IOWR, and IOWX instructions. The
b7
P0.7
R/W
1
b6
P0.6
R/W
1
b5
P0.5
R/W
1
b4
P0.4
R/W
1
b3
P0.3
R/W
1
b2
P0.2
R/W
1
b1
P0.1
R/W
1
b0
P0.0
R/W
1
Figure 6-8. Port 0 Data Register (Address 0x00)
b7
P1.7
R/W
1
b6
P1.6
R/W
1
b5
P1.5
R/W
1
b4
P1.4
R/W
1
b3
P1.3
R/W
1
b2
P1.2
R/W
1
b1
P1.1
R/W
1
b0
P1.0
R/W
1
Figure 6-9. Port 1 Data Register (Address 0x01)
Document #: 38-08026 Rev. *A
Page 8 of 25
CY7C63001A
CY7C63101A
Each GPIO line includes an internal Rup resistor. This resistor
provides both the pull-up function and slew control. Two
factors govern the enabling and disabling of each resistor: the
state of its associated Port Pull-up register bit and the state of
the Data Register bit. NOTE: The control bits in the Port Pull-
up register are active LOW.
diagram of one I/O line. The Port Isink Register is used to
control the output current level and it is described later in this
section. NOTE: The Isink logic block is turned off during
suspend mode (please refer to the Instant-on Feature section
for more details). Therefore, to prevent higher ICC currents
during USB suspend mode, firmware must set ALL Port 0 and
Port 1 Data Register bits (which are not externally driven to a
known state), including those that are not bonded out on a
particular package, to “1” and all Port 0 and Port 1 Pull-Up
Register data bits to “0” to enable port pull-ups before setting
the Suspend bit (bit 3 of the Status and Control Register).
Table 6-2 is the Output Control truth table.
A GPIO line is HIGH when a “1” is written to the Data Register
and a “0” is written to the respective Port Pull-up register.
Writing a “0” to the port Data Register disables the port’s Pull-
up resistor and outputs a LOW on the GPIO line regardless of
the setting in the Port Pull-up Register. The output goes to a
high-Z state if the Data Register bit and the Port Pull-up
Register bit are both “1”. Figure 6-10 illustrates the block
VCC
Port Pull-Up
Register
Rup
Port Data
Register
GPIO
Pin
Port Isink
Register
Isink
DAC
Disable
Suspend
Bit
Schmitt
Trigger
Data Bus
Figure 6-10. Block Diagram of an I/O Line
Table 6-2. Output Control Truth Table
Data Register
Port Pull-up Register
Output at I/O Pin
Sink Current (‘0’)
Sink Current (‘0’)
Pull-up Resistor (‘1’)
Hi-Z
Interrupt Polarity
High to Low
0
0
1
1
0
1
0
1
Low to High
High to Low
Low to High
To configure a GPIO pin as an input, a “1” should be written to
the Port Data Register bit associated with that pin to disable
the pull-down function of the Isink DAC (see Figure 6-
10).When the Port Data Register is read, the bit value is a “1”
if the voltage on the pin is greater than the Schmitt trigger
threshold, or “0” if it is below the threshold. In applications
where an internal pull-up is required, the Rup pull-up resistor
can be engaged by writing a “0” to the appropriate bit in the
Port Pull-up Register.
Both Port 0 and Port 1 Pull-up Registers are write only (see
Figures 6-11 and 6-12). The Port 0 Pull-up Register is located
at I/O address 0x08 and Port 1 Pull-up Register is mapped to
address 0x09. The contents of the Port Pull-up Registers are
cleared during reset, allowing the outputs to be controlled by
the state of the Data Registers. The Port Pull-up Registers also
select the polarity of transition that generates a GPIO interrupt.
A “0” selects a HIGH to LOW transition while a “1” selects a
LOW to HIGH transition.
b7
b6
b5
b4
b3
b2
b1
b0
PULL0.7
PULL0.6
PULL0.5
PULL0.4
PULL0.3
PULL0.2
PULL0.1
PULL0.0
W
0
W
0
W
0
W
0
W
0
W
0
W
0
W
0
Figure 6-11. Port 0 Pull-up Register (Address 0x08)
Document #: 38-08026 Rev. *A
Page 9 of 25
CY7C63001A
CY7C63101A
b7
PULL1.7
W
b6
b5
b4
b3
b2
b1
b0
PULL1.6
PULL1.5
PULL1.4
PULL1.3
PULL1.2
PULL1.1
PULL1.0
W
0
W
0
W
0
W
0
W
0
W
0
W
0
0x
Figure 6-12. Port 1 Pull-up Register (Address 0x09)
Writing a “0” to the Data Register drives the output LOW.
Instead of providing a fixed output drive, the USB Controller
allows the user to select an output sink current level for each
I/O pin. The sink current of each output is controlled by a
dedicated Port Isink Register. The lower four bits of this
register contain a code selecting one of sixteen sink current
levels. The upper four bits of the register are ignored. The
format of the Port Isink Register is shown in Figure 6-13.
b7
b6
b5
b4
b3
ISINK3
W
b2
ISINK2
W
b1
ISINK1
W
b0
ISINK0
W
Reserved
Reserved
Reserved
UNUSED
W
x
W
x
W
x
W
x
x
x
x
x
Figure 6-13. Port Isink Register for One GPIO Line
Port 0 is a low-current port suitable for connecting photo
transistors. Port 1 is a high current port capable of driving
LEDs. See section 8.0 for current ranges. 0000 is the lowest
drive strength. 1111 is the highest.
registers are cleared during a reset, resulting in the minimum
current sink setting.
6.7
XTALIN/XTALOUT
The write-only sink current control registers for Port 0 outputs
are assigned from I/O address 0x30 to 0x37 with the control
bits for P00 starting at 0x30. Port 1 sink current control
registers are assigned from I/O address 0x38 to 0x3F with the
control bits for P10 starting at 0x38. All sink current control
The XTALIN and XTALOUT pins support connection of a 6-
MHz ceramic resonator. The feedback capacitors and bias
resistor are internal to the IC, as shown in Figure 6-14 Leave
XTALOUT unconnected when driving XTALIN from an external
oscillator.
XTALOUT
clk1x
(to USB SIE)
Clock
clk2x
XTALIN
Doubler
(to Microcontroller)
30 pF
30 pF
Figure 6-14. Clock Oscillator On-chip Circuit
instructions to address 0x20. Writing a “1” to a bit position
enables the interrupt associated with that position. During a
reset, the contents of the Interrupt Enable Register are
cleared, disabling all interrupts. Figure 6-15 illustrates the
format of the Global Interrupt Enable Register.
6.8
Interrupts
Interrupts are generated by the General Purpose I/O lines, the
Cext pin, the internal timer, and the USB engine. All interrupts
are maskable by the Global Interrupt Enable Register. Access
to this register is accomplished via IORD, IOWR, and IOWX
b7
CEXTIE
R/W
0
b6
GPIOIE
R/W
0
b5
b4
EP1IE
R/W
0
b3
EP0IE
R/W
0
b2
1024IE
R/W
0
b1
128IE
R/W
0
b0
Reserved
Reserved
0
0
Figure 6-15. Global Interrupt Enable Register (GIER – Address 0x20)
The interrupt controller contains a separate latch for each
interrupt. See Figure 6-16 for the logic block diagram for the
interrupt controller. When an interrupt is generated, it is
latched as a pending interrupt. It stays as a pending interrupt
until it is serviced or a reset occurs. A pending interrupt only
generates an interrupt request if it is enabled in the Global
Interrupt Enable Register. The highest priority interrupt
request is serviced following the execution of the current
instruction.
Document #: 38-08026 Rev. *A
Page 10 of 25
CY7C63001A
CY7C63101A
When servicing an interrupt, the hardware first disables all
interrupts by clearing the Global Interrupt Enable Register.
Next, the interrupt latch of the current interrupt is cleared. This
is followed by a CALL instruction to the ROM address
associated with the interrupt being serviced (i.e., the interrupt
vector). The instruction in the interrupt table is typically a JMP
instruction to the address of the Interrupt Service Routine
(ISR). The user can re-enable interrupts in the interrupt service
routine by writing to the appropriate bits in the Global Interrupt
Enable Register. Interrupts can be nested to a level limited
only by the available stack space.
process. The user firmware is responsible for ensuring that the
processor state is preserved and restored during an interrupt.
For example the PUSH A instruction should be used as the
first command in the ISR to save the accumulator value. And,
the IPRET instruction should be used to exit the ISR with the
accumulator value restored and interrupts enabled. The PC,
CF, and ZF are restored when the IPRET or RET instructions
are executed.
The Interrupt Vectors supported by the USB Controller are
listed in Table 6-3. Interrupt Vector 0 (Reset) has the highest
priority, Interrupt Vector 7 has the lowest priority. Because the
JMP instruction is two bytes long, the interrupt vectors occupy
two bytes.
The Program Counter (PC) value and the Carry and Zero flags
(CF, ZF) are automatically stored onto the Program Stack by
the CALL instruction as part of the interrupt acknowledge
Table 6-3. Interrupt Vector Assignments
Interrupt Priority
ROM Address
0x00
Function
0 (Highest)
Reset
1
0x02
0x04
0x06
0x08
0x0A
0x0C
0x0E
128-µs timer interrupt
1.024-ms timer interrupt
USB endpoint 0 interrupt
USB endpoint 1 interrupt
Reserved
2
3
4
5
6
GPIO interrupt
7 (Lowest)
Wake-up interrupt
6.8.1
Interrupt Latency
For example, if a 5-clock-cycle instruction such as JC is being
executed when an interrupt occurs, the first instruction of the
Interrupt Service Routine executes a minimum of 16 clock
cycles (1+10+5) or a maximum of 20 clock cycles (5+10+5)
after the interrupt is issued. Therefore, the interrupt latency in
this example will be = 20 clock periods = 20 / (12 MHz) = 1.667
µs. The interrupt latches are sampled at the rising edge of the
last clock cycle in the current instruction.
Interrupt latency can be calculated from the following
equation:
Interrupt Latency = (Number of clock cycles remaining in the
current instruction) + (10 clock cycles for
the CALL instruction) + (5 clock cycles
for the JMP instruction)
128-
128-
m
s CLR
s IRQ
CLR
D
Logic 1
128-
Q
m
Enable [1]
1-ms CLR
1-ms IRQ
m
s
CLK
Interrupt
IRQ
End P0 CLR
End P0 IRQ
End P1 CLR
End P1 IRQ
Global
Interrupt
Enable
Interrupt
Vector
Enable [7:0]
GPIO CLR
GPIO IRQ
Register
CLR
CLR
Logic 1
D
Q
Q
Enable [6]
Enable [7]
GPIO
Interrupt
Interrupt
Acknowledge
CLK
Wake-up CLR
Wake-up IRQ
CLR
Logic 1
CEXT
D
Interrupt
Priority
CLK
Encoder
Figure 6-16. Interrupt Controller Logic Block Diagram
Document #: 38-08026 Rev. *A
Page 11 of 25
CY7C63001A
CY7C63101A
6.8.2
GPIO Interrupt
LOW interrupt trigger. Each GPIO interrupt is maskable on a
per-pin basis by a dedicated bit in the Port Interrupt Enable
Register. Writing a “1” enables the interrupt. Figure 6-17 and
Figure 6-18 illustrate the format of the Port Interrupt Enable
Registers for Port 0 and Port 1 located at I/O address 0x04 and
0x05 respectively. These write only registers are cleared
during reset, thus disabling all GPIO interrupts.
The General Purpose I/O interrupts are generated by signal
transitions at the Port 0 and Port 1 I/O pins. GPIO interrupts
are edge sensitive with programmable interrupt polarities.
Setting a bit HIGH in the Port Pull-up Register (see Figure 6-
11 and 6-12) selects a LOW to HIGH interrupt trigger for the
corresponding port pin. Setting a bit LOW activates a HIGH to
b7
IE0.7
W
b6
IE0.6
W
b5
IE0.5
W
b4
IE0.4
W
b3
IE0.3
W
b2
IE0.2
W
b1
IE0.1
W
b0
IE0.0
W
0
0
0
0
0
0
0
0
Figure 6-17. Port 0 Interrupt Enable Register (P0 IE – Address 0x04)
b7
IE1.7
W
b6
IE1.6
W
b5
IE1.5
W
b4
IE1.4
W
b3
IE1.3
W
b2
IE1.2
W
b1
IE1.1
W
b0
IE1.0
W
0
0
0
0
0
0
0
0
Figure 6-18. Port 1 Interrupt Enable Register (P1 IE – Address 0x05)
A block diagram of the GPIO interrupt logic is shown in Figure
6-19. The bit setting in the Port Pull-up Register selects the
interrupt polarity. If the selected signal polarity is detected on
the I/O pin, a HIGH signal is generated. If the Port Interrupt
Enable bit for this pin is HIGH and no other port pins are
requesting interrupts, the OR gate issues a LOW to HIGH
signal to clock the GPIO interrupt flip-flop. The output of the
flip-flop is further qualified by the Global GPIO Interrupt Enable
bit before it is processed by the Interrupt Priority Encoder. Both
the GPIO interrupt flip-flop and the Global GPIO Enable bit are
cleared by on-chip hardware during GPIO interrupt
acknowledge.
Port
Pull-Up
Register
→
10=LHÆH
L
GPIO Interrupt
Flip-Flop
OR Gate
(1 input per
GPIO pin)
I
D
Q
M
U
X
GPIO
Pin
CLR
Port Interrupt
Enable Register
1 = Enable
0 = Disable
Interrupt
Acknowledge
CLR
IRQ
Interrupt
Priority
Encoder
Global
GPIO Interrupt
Enable
1 = Enable
0 = Disable
Interrupt
Vector
(Bit 6, Register 0x20)
Figure 6-19. GPIO Interrupt Logic Block Diagram
Note. If one port pin triggers an interrupt, no other port pin can
cause a GPIO interrupt until the port pin that triggered the
interrupt has returned to its inactive (non-trigger) state or until
its corresponding port interrupt enable bit is cleared (these
events ‘reset’ the clock of the GPIO Interrupt flip-flop, which
must be ‘reset’ to ‘0’ before another GPIO interrupt event can
‘clock’ the GPIO Interrupt flip-flop and produce an IRQ).
enable bit is cleared and then set, a GPIO interrupt event
occurs as the GPIO Interrupt flip-flop clock transitions from ‘1’
to ‘0’ and then back to ‘1’ (please refer to Figure 6-19). The
USB Controller does not assign interrupt priority to different
port pins and the Port Interrupt Enable Registers are not
cleared during the interrupt acknowledge process. When a
GPIO interrupt is serviced, the ISR must poll the ports to
determine which pin caused the interrupt.
Note. If the port pin that triggered an interrupt is held in its
active (trigger) state while its corresponding port interrupt
Document #: 38-08026 Rev. *A
Page 12 of 25
CY7C63001A
CY7C63101A
6.8.3
USB Interrupt
6.9
USB Engine
A USB Endpoint 0 interrupt is generated after the host has
written data to Endpoint 0 or after the USB Controller has
transmitted a packet from Endpoint 0 and receives an ACK
from the host. An OUT packet from the host which is NAKed
by the USB Controller does not generate an interrupt. This
interrupt is masked by the USB EP0 Interrupt Enable bit (bit 3)
of the Global Interrupt Enable Register.
The USB engine includes the Serial Interface Engine (SIE)
and the low-speed USB I/O transceivers. The SIE block
performs most of the USB interface functions with only minimal
support from the microcontroller core. Two endpoints are
supported. Endpoint 0 is used to receive and transmit control
(including setup) packets while Endpoint 1 is only used to
transmit data packets.
A USB Endpoint 1 interrupt is generated after the USB
Controller has transmitted a packet from Endpoint 1 and has
received an ACK from the host. This interrupt is masked by the
USB EP1 Interrupt Enable bit (bit 4) of the Global Interrupt
Enable Register.
The USB SIE processes USB bus activity at the transaction
level independently. It does all the NRZI encoding/decoding
and bit stuffing/unstuffing. It also determines token type,
checks address and endpoint values, generates and checks
CRC values, and controls the flow of data bytes between the
bus and the Endpoint FIFOs. NOTE: the SIE stalls the CPU for
three cycles per byte when writing data to the endpoint FIFOs
(or 3 * 1/12 MHz * 8 bytes = 2 µs per 8-byte transfer).
6.8.4
Timer Interrupt
There are two timer interrupts: the 128-µs interrupt and the
1.024-ms interrupt. They are masked by bits 1 and 2 of the
Global Interrupt Enable Register respectively. The user should
disable both timer interrupts before going into the suspend
mode to avoid possible conflicts from timer interrupts occurring
just as suspend mode is entered.
The firmware handles higher level and function-specific tasks.
During control transfers the firmware must interpret device
requests and respond correctly. It also must coordinate
Suspend/Resume, verify and select DATA toggle values, and
perform function specific tasks.
The USB engine and the firmware communicate though the
Endpoint FIFOs, USB Endpoint interrupts, and the USB
registers described in the sections below.
6.8.5
Wake-Up Interrupt
A wake-up interrupt is generated when the Cext pin goes
HIGH. This interrupt is latched in the interrupt controller. It can
be masked by the Wake-up Interrupt Enable bit (bit 7) of the
Global Interrupt Enable Register. This interrupt can be used to
perform periodic checks on attached peripherals when the
USB Controller is placed in the low-power suspend mode. See
the Instant-On Feature section for more details.
6.9.1
USB Enumeration Process
The USB Controller provides a USB Device Address Register
at I/O location 0x12. Reading and writing this register is
achieved via the IORD and IOWR instructions. The register
contents are cleared during a reset, setting the USB address
of the USB Controller to 0. Figure 6-20 shows the format of the
USB Address Register.
b7
b6
ADR6
R/W
0
b5
ADR5
R/W
0
b4
ADR4
R/W
0
b3
ADR3
R/W
0
b2
ADR2
R/W
0
b1
ADR1
R/W
0
b0
ADR0
R/W
0
Reserved
0
Figure 6-20. USB Device Address Register (USB DA – Address 0x12)
Typical enumeration steps:
8. The host performs a control read sequence and the USB
Controller responds by sending its Device descriptor over
the USB bus.
1. The host computer sends a SETUP packet followed by a
DATA packet to USB address 0 requesting the Device
descriptor.
9. The host generates control reads to the USB Controller to
request the Configuration and Report descriptors.
2. The USB Controller decodes the request and retrieves its
Device descriptor from the program memory space.
10.The USB Controller retrieves the descriptors from its
program space and returns the data to the host over the
USB.
3. The host computer performs a control read sequence and
the USB Controller responds by sending the Device
descriptor over the USB bus.
11.Enumeration is complete after the host has received all the
descriptors.
4. After receiving the descriptor, the host computer sends a
SETUP packet followed by a DATA packet to address 0
assigning a new USB address to the device.
5. The USB Controller stores the new address in its USB
Device Address Register after the no-data control
sequence completes.
6. The host sends a request for the Device descriptor using
the new USB address.
7. The USB Controller decodes the request and retrieves the
Device descriptor from the program memory.
Document #: 38-08026 Rev. *A
Page 13 of 25
CY7C63001A
CY7C63101A
6.9.2
Endpoint 0
6.9.2.1 Endpoint 0 Receive
All USB devices are required to have an endpoint number 0
that is used to initialize and manipulate the device. Endpoint 0
provides access to the device’s configuration information and
allows generic USB status and control accesses.
After receiving a packet and placing the data into the Endpoint
0 FIFO, the USB Controller updates the USB Endpoint 0 RX
register to record the receive status and then generates a USB
Endpoint 0 interrupt. The format of the Endpoint 0 RX Register
is shown in Figure 6-21.
Endpoint 0 can receive and transmit data. Both receive and
transmit data share the same 8-byte Endpoint 0 FIFO located
at data memory space 0x70 to 0x77. Received data may
overwrite the data previously in the FIFO.
b7
COUNT3
R/W
b6
COUNT2
R/W
b5
COUNT1
R/W
b4
COUNT0
R/W
b3
b2
IN
b1
OUT
R/W
0
b0
SETUP
R/W
0
TOGGLE
R
0
R/W
0
0
0
0
0
Figure 6-21. USB Endpoint 0 RX Register (Address 0x14)
This is a read/write register located at I/O address 0x14. Any
write to this register clears all bits except bit 3 which remains
unchanged. All bits are cleared during reset.
received. The count is always updated and the data is always
stored in the FIFO for DATA packets following a SETUP token.
The count for DATA following an OUT token is updated if Stall
(bit 5 of 0x10) is 0 and either EnableOuts or StatusOuts (bits
3 and 4 of 0x13) are 1. The DATA following an OUT is written
into the FIFO if EnableOuts is set to 1 and Stall and StatusOuts
are 0.
Bit 0 is set to 1 when a SETUP token for Endpoint 0 is received.
Once set to a 1, this bit remains HIGH until it is cleared by an
I/O write or a reset. While the data following a SETUP is being
received by the USB engine, this bit is not cleared by an I/O
write. User firmware writes to the USB FIFOs are disabled
when bit 0 is set. This prevents SETUP data from being
overwritten.
A maximum of eight bytes are written into the Endpoint 0 FIFO.
If there are less than eight bytes of data the CRC is written into
the FIFO.
Bits 1 and 2 are updated whenever a valid token is received
on Endpoint 0. Bit 1 is set to 1 if an OUT token is received and
cleared to 0 if any other token is received. Bit 2 is set to 1 if an
IN token is received and cleared to 0 if any other token is
received.
Due to register space limitations, the Receive Data Invalid bit
is located in the USB Endpoint 0 TX Configuration Register.
Refer to the Endpoint 0 Transmit section for details. This bit is
set by the SIE if an error is detected in a received DATA packet.
Table 6-4 summarizes the USB Engine response to SETUP
and OUT transactions on Endpoint 0. In the Data Packet
column ‘Error’ represents a packet with a CRC, PID or bit-
stuffing error, or a packet with more than eight bytes of data.
‘Valid’ is a packet without an Error. ‘Status’ is a packet that is
a valid control read Status stage, while ‘N/Status’ is not a
correct Status stage (see section 6.9.4). The ‘Stall’ bit is
described in Section 6.9.2.2. The ‘StatusOuts’ and
‘EnableOuts’ bits are described in section 6.9.4.
Bit 3 shows the Data Toggle status of DATA packets received
on Endpoint 0. This bit is updated for DATA following SETUP
tokens and for DATA following OUT tokens if Stall (bit 5 of
0x10) is not set and either EnableOuts or StatusOuts (bits 3
and 4 of 0x13) are set.
Bits 4 to 7 are the count of the number of bytes received in a
DATA packet. The two CRC bytes are included in the count,
so the count value is two greater than the number of data bytes
Table 6-4. USB Engine Response to SETUP and OUT Transactions on Endpoint 0
Control Bit Settings Received Packets USB Engine Response
Token
Type
Data
Toggle
Count
Stall
Status Out EnableOut
Packet FIFO Write Update
Update
Interrupt
Yes
Yes
Yes
Yes
No
Reply
ACK
–
–
0
0
0
0
1
1
0
0
0
–
–
0
0
0
0
0
0
1
1
1
–
–
1
1
0
0
0
0
0
0
0
SETUP
SETUP
OUT
Valid
Error
Yes
Yes
Yes
Yes
No
No
No
No
No
No
No
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
No
None
ACK
Valid
OUT
Error
None
NAK
OUT
Valid
OUT
Error
No
No
No
None
STALL
None
ACK
OUT
Valid
No
No
No
OUT
Error
No
No
No
OUT
Status
N/Status
Error
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
No
OUT
STALL
None
OUT
Document #: 38-08026 Rev. *A
Page 14 of 25
CY7C63001A
CY7C63101A
6.9.2.2 Endpoint 0 Transmit
The USB Endpoint 0 TX Register located at I/O address 0x10
controls data transmission from Endpoint 0 (see Figure 6-22).
This is a read/write register. All bits are cleared during reset.
b7
INEN
R/W
0
b6
DATA1/0
R/W
b5
STALL
R/W
0
b4
ERR
R/W
0
b3
COUNT3
R/W
b2
COUNT2
R/W
b1
b0
COUNT1
COUNT0
R/W
0
R/W
0
0
0
0
Figure 6-22. USB Endpoint 0 TX Configuration Register (Address 0x10)
Bits 0 to 3 indicate the numbers of data bytes to be transmitted
during an IN packet, valid values are 0 to 8 inclusive. Bit 4
indicates that a received DATA packet error (CRC, PID, or
bitstuffing error) occurred during a SETUP or OUT data phase.
Setting the Stall bit (bit 5) stalls IN and OUT packets. This bit
is cleared whenever a SETUP packet is received by
Endpoint 0. Bit 6 (Data 1/0) must be set to 0 or 1 to select the
DATA packet’s toggle state (0 for DATA0, 1 for DATA1).
received. The Interrupt Service Routine can check bit 7 to
confirm that the data transfer was successful.
6.9.3
Endpoint 1
Endpoint 1 is capable of transmit only. The data to be trans-
mitted is stored in the 8-byte Endpoint 1 FIFO located at data
memory space 0x78 to 0x7F.
After the transmit data has been loaded into the FIFO, bit 6
should be set according to the data toggle state and bit 7 set
to “1”. This enables the USB Controller to respond to an IN
packet. Bit 7 is cleared and an Endpoint 0 interrupt is
generated by the SIE once the host acknowledges the data
transmission. Bit 7 is also cleared when a SETUP token is
6.9.3.1 Endpoint 1 Transmit
Transmission is controlled by the USB Endpoint 1 TX Register
located at I/O address 0x11 (see Figure 6-23). This is a
read/write register. All bits are cleared during reset.
b7
INEN
R/W
0
b6
DATA1/0
R/W
b5
STALL
R/W
0
b4
EP1EN
R/W
0
b3
COUNT3
R/W
b2
COUNT2
R/W
b1
COUNT1
R/W
b0
COUNT0
R/W
0
0
0
0
0
Figure 6-23. USB Endpoint 1 TX Configuration Register (Address 0x11)
Bits 0 to 3 indicate the numbers of data bytes to be transmitted
during an IN packet, valid values are 0 to 8 inclusive.
to “1”. This enables the USB Controller to respond to an IN
packet. Bit 7 is cleared and an Endpoint 1 interrupt is
generated by the SIE once the host acknowledges the data
transmission.
Bit 4 must be set before Endpoint 1 can be used. If this bit is
cleared, the USB Controller ignores all traffic to Endpoint 1.
Setting the Stall bit (bit 5) stalls IN and OUT packets until this
bit is cleared.
6.9.4
USB Status and Control
USB status and control is regulated by USB Status and Control
Register located at I/O address 0x13 as shown in Figure 6-24.
This is a read/write register. All reserved bits must be written
to zero. All bits in the register are cleared during reset.
Bit 6 (Data 1/0) must be set to either 0 or 1 depending on the
data packet’s toggle state, 0 for DATA0, 1 for DATA1.
After the transmit data has been loaded into the FIFO, bit 6
should be set according to the data toggle state and bit 7 set
b7
b6
b5
b4
ENOUTS
R/W
b3
STATOUTS
R/W
b2
b1
FORCEK
R/W
b0
BUSACT
R/W
Reserved
Reserved
Reserved
FORCEJ
0
0
0
0
0
0
0
0
Figure 6-24. USB Status and Control Register (USB SCR – Address 0x13)
Bit 0 is set by the SIE if any USB activity except idle (D+ LOW,
D– HIGH) is detected. The user program should check and
clear this bit periodically to detect any loss of bus activity.
Writing a 0 to this bit clears it. Writing a 1 does not change its
value.
zero. However, for resume signaling, force a J state for one
instruction before forcing resume.
Bit 3 is used to automatically respond to the Status stage OUT
of a control read transfer on Endpoint 0. A valid Status stage
OUT contains a DATA1 packet with 0 bytes of data. If the Statu-
sOuts bit is set, the USB engine responds to a valid Status
stage OUT with an ACK, and any other OUT with a STALL.
Bit 1 is used to force the on-chip USB transmitter to the K state
which sends a Resume signal to the host. Bit 2 is used to force
the transmitter to the J state. This bit should normally be set to
Document #: 38-08026 Rev. *A
Page 15 of 25
CY7C63001A
CY7C63101A
The data is not written into the FIFO when this bit is set. This
bit is cleared when a SETUP token is received by Endpoint 0.
6.10.1 Low-Speed Driver Characteristics
The CY7C630/101A devices use a differential output driver to
drive the Low-speed USB data signal onto the USB cable, as
shown in Figure 6-25. The output swings between the differ-
ential HIGH and LOW state are well balanced to minimize
signal skew. Slew rate control on the driver minimizes the
radiated noise and cross talk on the USB cable. The driver’s
outputs support three-state operation to achieve bidirectional
half duplex operation. The CY7C630/101A driver tolerates a
voltage on the signal pins of –0.5V to 3.8V with respect to local
ground reference without damage. The driver tolerates this
voltage for 10.0 µs while the driver is active and driving, and
tolerates this condition indefinitely when the driver is in its high-
impedance state.
Bit 4 is used to enable the receiving of Endpoint 0 OUT
packets. When this bit is set to 1, the data from an OUT trans-
action is written into the Endpoint 0 FIFO. If this bit is 0, data
is not written to the FIFO and the SIE responds with a NAK.
This bit is cleared following a SETUP or ACKed OUT trans-
action. Note. After firmware decodes a SETUP packet and
prepares for a subsequent OUT transaction by setting bit 4, bit
4 is not cleared until the hand-shake phase of an ACKed OUT
transaction (a NAKed OUT transaction does not clear this bit).
6.10
USB Physical Layer Characteristics
The following section describes the CY7C630/101A
compliance to the Chapter 7 Electrical section of the USB
Specification, Revision 1.1. The section contains all signaling,
power distribution, and physical layer specifications necessary
to describe a low- speed USB function.
A low-speed USB connection is made through an unshielded,
untwisted wire cable a maximum of three meters in length. The
rise and fall time of the signals on this cable are well controlled
to reduce RFI emissions while limiting delays, signaling skews
and distortions. The CY7C630/101A driver reaches the
specified static signal levels with smooth rise and fall times,
resulting in minimal reflections and ringing when driving the
USB cable. This cable and driver are intended to be used only
on network segments between low-speed devices and the
ports to which they are connected.
One Bit
Time
(1.5Mb/s)
Signal pins
pass output
spec levels
with minimal
reflections and
ringing
VSE (max)
Driver
Signal Pins
VSE (min)
VSS
Figure 6-25. Low-speed Driver Signal Waveforms
6.10.2 Receiver Characteristics
the differential data lines are outside the common mode range,
as shown in Figure 6-26. The receiver tolerates static input
voltages between –0.5V and 3.8V with respect to its local
ground reference without damage. In addition to the differ-
ential receiver, there is a single-ended receiver for each of the
two data lines. The single-ended receivers have a switching
threshold between 0.8V and 2.0V (TTL inputs).
The CY7C630/101A has a differential input receiver which is
able to accept the USB data signal. The receiver features an
input sensitivity of at least 200 mV when both differential data
inputs are in the range of at least 0.8V to 2.5V with respect to
its local ground reference. This is the common mode input
voltage range. Proper data reception is also guaranteed when
Document #: 38-08026 Rev. *A
Page 16 of 25
CY7C63001A
CY7C63101A
1.0
0.8
0.6
0.4
0.2
0.0
0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2
Common Mode Input Voltage (volts)
Figure 6-26. Differential Input Sensitivity Over Entire Common Mode Range
trace capacitance + integrated cable capacitance) must be
less than 250 pF. As Cypress D+/D– transceiver input capac-
itance is 20pF max, up to 230 pF of capacitance is allowed for
in the low speed device’s integrated cable and PCB. If the
cable + PCB capacitance on the D+/D– lines will be greater
than approximately 230 pF, an external 3.3V regulator must be
used as shown in Figure 6-28.
6.11
External USB Pull-Up Resistor
The USB system specifies that a pull-up resistor be connected
on the D– pin of low-speed peripherals as shown in Figure 6-
27. To meet the USB 1.1 spec (section 7.1.6), which states that
the termination must charge the D– line from 0 to 2.0 V in
2.5 µs, the total load capacitance on the D+/D– lines of the
low-speed USB device (Cypress device capacitance + PCB
Port0
Port0
Switches,
Devices, Etc.
Switches,
Devices, Etc.
Port1
D+
Port1
VSS
VPP
D–
VCC
XTALOUT
CEXT
XTALIN
7.5kW±1%
+4.35V (min)
For Cext
Wake-up Mode
0.1µF
6-MHz
Resonator
4.7 µF
Figure 6-27. Application Showing 7.5kW ±1% Pull-Up Resistor
+3.3V
3.3V
Reg
Port0
Port0
Switches,
Devices, Etc.
Switches,
Devices, Etc.
0.1 µF
Port1
D+
D–
Port1
1.5±kW
V
V
SS
PP
V
CEXT
CC
XTALIN
XTALOUT
+4.35V (min.)
For Cext
Wake-up Mode
0.1µF
6-MHz
Resonator
4.7 µF
Figure 6-28. Application Showing 1.5-kW ±5% Pull-Up Resistor
Document #: 38-08026 Rev. *A
Page 17 of 25
CY7C63001A
CY7C63101A
6.12
Table 6-5. Instruction Set Map
MNEMONIC operand
Instruction Set Summary
opcode
00
cycles
MNEMONIC
operand
opcode
20
cycles
HALT
7
NOP
4
4
4
7
8
4
4
7
8
5
5
4
4
5
5
5
5
5
6
7
8
7
8
7
8
6
4
4
4
4
4
8
ADD A,expr
data
direct
index
data
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
OE
0F
10
11
4
INC A
acc
21
22
23
24
25
26
27
28
29
2A
2B
2C
2D
2E
2F
30
31
32
33
34
35
36
37
38
39
3A
3B
3C
3D
3E
3F
ADD A,[expr]
ADD A,[X+expr]
ADC A,expr
6
7
4
6
7
4
6
7
4
6
7
4
6
7
4
6
7
4
6
7
5
7
8
4
5
6
4
5
INC X
x
INC [expr]
INC [X+expr]
DEC A
direct
index
acc
ADC A,[expr]
ADC A,[X+expr]
SUB A,expr
direct
index
data
DEC X
x
DEC [expr]
DEC [X+expr]
IORD expr
IOWR expr
POP A
direct
index
address
address
SUB A,[expr]
SUB A,[X+expr]
SBB A,expr
direct
index
data
SBB A,[expr]
SBB A,[X+expr]
OR A,expr
direct
index
data
POP X
PUSH A
OR A,[expr]
direct
index
data
PUSH X
OR A,[X+expr]
AND A,expr
SWAP A,X
SWAP A,DSP
MOV [expr],A
MOV [X+expr],A
OR [expr],A
OR [X+expr],A
AND [expr],A
AND [X+expr],A
XOR [expr],A
XOR [X+expr],A
IOWX [X+expr]
CPL
AND A,[expr]
AND A,[X+expr]
XOR A,expr
XOR A,[expr]
XOR A,[X+expr]
CMP A,expr
CMP A,[expr]
CMP A,[X+expr]
MOV A,expr
MOV A,[expr]
MOV A,[X+expr]
MOV X,expr
MOV X,[expr]
IPRET
direct
index
data
direct
index
direct
index
direct
index
direct
index
index
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
direct
index
data
direct
index
data
direct
index
data
ASL
ASR
direct
addr
RLC
13
4
RRC
XPAGE
RET
JMP
CALL
JZ
addr
addr
addr
addr
8x
9x
Ax
Bx
5
JC
addr
addr
addr
addr
Cx
Dx
Ex
Fx
5
5
7
10
5
JNC
JACC
INDEX
JNZ
5
14
Document #: 38-08026 Rev. *A
Page 18 of 25
CY7C63001A
CY7C63101A
DC Voltage Applied to Outputs in
7.0
Absolute Maximum Ratings
High-Z state ......................................... –0.5V to +VCC+0.5V
Max. Output Current into Port 1 Pins .......................... 60 mA
Max. Output Current into Non-Port 1 Pins.................. 10 mA
Power Dissipation..................................................... 300 mW
Static Discharge Voltage .......................................... >2000V
Latch-up Current[1] ................................................ > 200 mA
Storage Temperature .................................–65°C to +150°C
Ambient Temperature with Power Applied......–0°C to +70°C
Supply Voltage on VCC Relative to VSS ......... –0.5V to +7.0V
DC Input Voltage................................... –0.5V to +VCC+0.5V
8.0
Electrical Characteristics fOSC = 6 MHz; Operating Temperature = 0 to 70°C, VCC = 4.0 to 5.25V
Parameter
Description
General
Conditions
Resonator off, D– > Voh min[2]
Ceramic resonator
Min.
Max.
Unit
ICC
VCC Operating Supply Current
Supply Current—Suspend Mode
Supply Current—Start-up Mode
Programming Voltage (disabled)
Resonator Start-up Interval
Watchdog Timer Period
25
20
mA
µA
mA
V
ISB1
ISB2
4
VPP
tstart
twatch
–0.4
0.4
256
µs
7.168 8.192
ms
Power On Reset
[3, 4]
tVCCS
VCC Slew
Linear ramp on VCC pin to VCC
0.010
2.8
1000
ms
USB Interface
Voh
Vol
Static Output High
15kΩ ± 5% to Gnd[5,6]
See Notes 5 and 6
|(D+)–(D–)|, and Figure 6-26
Figure 6-26
3.6
0.3
V
V
Static Output Low
Vdi
Differential Input Sensitivity
Differential Input Common Mode Range
Single Ended Receiver Threshold
Transceiver Input Capacitance
Data Line (D+, D–) Leakage
External Bus Pull-up Resistance, D– pin
External Bus Pull-up Resistance, D– pin
External Bus Pull-down Resistance
General Purpose I/O Interface
Pull-up Resistance
0.2
0.8
0.8
V
Vcm
Vse
Cin
2.5
2.0
20
V
V
D+ to Vss; D- to Vss
pF
µA
kΩ
kΩ
kΩ
Ilo
0 V <(D+, D–)<3.3 V, Hi-Z State
1.5 kΩ ± 5% to 3.3V supply
7.5 kΩ ± 1% to Vcc[7]
15 kΩ ± 5%
–10
10
Rpu1
Rpu2
Rpd
1.425 1.575
7.425 7.575
14.25 15.75
Rup
8
24
0.3
1.5
4.8
24
kΩ
mA
mA
mA
Isink0(0)
Isink0(F)
Isink1(0)
Isink1(F)
Port 0 Sink Current (0), lowest current
Port 0 Sink Current (F), highest current
Port 1 Sink Current (0), lowest current
Port 1 Sink Current (F), highest current
Vout = 2.0V DC, Port 0 only[5]
Vout = 2.0V DC, Port 0 only[5]
Vout = 2.0V DC, Port 1 only[5]
0.1
0.5
1.6
Vout = 2.0V DC, Port 1 only[5]
8
5
mA
mA
Vout = 0.4V DC, Port 1 only[5]
Irange
Ilin
Tratio
tsink
Sink Current max./min.
Vout = 2.0V DC, Port 0 or 1[5, 8]
Port 0 or Port 1[11]
Vout = 2.0V[12]
4.5
5.5
0.5
19.6
0.8
60
Differential Nonlinearity
lSB
Tracking Ratio Port1 to Port0
Current Sink Response Time
Port 1 Max Sink Current
14.4
Full scale transition
µs
Imax
Summed over all Port 1 bits
mA
Notes:
1. All pins specified for >200 mA positive and negative injection, except P1.0 is specified for >50 mA negative injection.
2. Cext at VCC or Gnd, Port 0 and Port1 at VCC
.
3. Part powers up in suspend mode, able to be reset by USB Bus Reset.
4. POR may re-occur whenever VCC drops to approximately 2.5V.
5. Level guaranteed for range of VCC = 4.35V to 5.25V.
6. With Rpu1 of 1.5 KW±5% on D– to 3.3V regulator.
7. Maximum matched capacitive loading allowed on D+ and D– (including USB cable and host/hub) is approximately 230 pF.
8. Irange = Isink(F)/Isink(0 ) for each port 0 or 1 output.
Document #: 38-08026 Rev. *A
Page 19 of 25
CY7C63001A
CY7C63101A
8.0
Electrical Characteristics fOSC = 6 MHz; Operating Temperature = 0 to 70°C, VCC = 4.0 to 5.25V (continued)
Parameter
Description
Port 1 & Cext Sink Mode Dissipation
Input Threshold Voltage
Conditions
Min.
Max.
25
Unit
mW
VCC
VCC
VCC
µA
Pmax
Vith
Per pin
All ports and Cext[13]
Port 0 and Port 1[14]
Cext Pin Only[14]
45%
6%
65%
12%
30%
1
VH
Input Hysteresis Voltage
VHCext
Iin
Input Hysteresis Voltage, Cext
Input Leakage Current, GPIO Pins
Input Leakage Current, Cext Pin
Sink Current, Cext Pin
12%
–1
[15]
Port 0 and Port 1, Vout = 0 or VCC
VCext = 0 or VCC
IinCx
ICext
Vol1
Vol2
50
nA
VCext = VCC
6
18
mA
V
Output LOW Voltage, Cext Pin
Output LOW Voltage, Cext Pin
VCC = Min., Iol = 2 mA
VCC = Min., Iol = 5 mA
0.4
2.0
V
9.0
Switching Characteristics
Parameter
Description
Clock
Conditions
Min.
Max.
Unit
tCYC
tCH
tCL
Input Clock Cycle Time
Clock HIGH Time
166.67
166.67
ns
ns
ns
0.45 tCYC
0.45 tCYC
Clock LOW Time
USB Driver Characteristics
USB Data Transition Rise Time
USB Data Transition Fall Time
Rise/Fall Time Matching
Output Signal Crossover Voltage
USB Data Timing
tr
See Notes 5, 6, and 9
75
75
300
300
125
2.0
ns
ns
%
V
tf
See Notes 5, 6, and 9
trfm
Vcrs
tr/tf
80
See Note 5
1.3
tdrate
tdjr1
tdjr2
tdeop
teopr
tlst
Low Speed Data Rate
Receiver Data Jitter Tolerance
Receiver Data Jitter Tolerance
Ave. Bit Rate (1.5 Mb/s ± 1.5%)
To Next Transition, Figure 9-3[10]
For Paired Transitions, Figure 9-3[10]
1.4775
–75
1.5225 Mb/s
75
45
ns
ns
ns
ns
ns
–45
Differential to EOP Transition Skew Figure 9-4[10]
–40
100
EOP Width at Receiver
Accepts as EOP[10]
670
Width of SE0 Interval During
Differential Transition
210
teopt
tudj1
tudj2
Source EOP Width
1.25
–95
1.50
95
µs
ns
ns
Differential Driver Jitter
Differential Driver Jitter
To next transition, Figure 9-5
To paired transition, Figure 9-5
–150
150
Notes:
9. Cload of 200 (75 ns) to 600 pF (300 ns).
10. Measured at crossover point of differential data signals.
11. Measured as largest step size vs. nominal according to measured full scale and zero programmed values
12. Tratio = Isink1(n)/Isink0(n) for the same n.
13. Low to High transition.
14. This parameter is guaranteed, but not tested.
15. With Ports configured in Hi-Z mode.
Document #: 38-08026 Rev. *A
Page 20 of 25
CY7C63001A
CY7C63101A
tCYC
tCH
CLOCK
tCL
Figure 9-1. Clock Timing
tf
tr
D+
D−
Voh
90%
90%
Vcrs
Vol
10%
10%
Figure 9-2. USB Data Signal Timing and Voltage Levels
TPERIOD
Differential
Data Lines
TJR
TJR1
TJR2
Consecutive
Transitions
N * TPERIOD + TJR1
Paired
Transitions
N * TPERIOD + TJR2
Figure 9-3. Receiver Jitter Tolerance
TPERIOD
Crossover
Point Extended
Crossover
Point
Differential
Data Lines
Diff. Data to
SE0 Skew
N * TPERIOD + TDEOP
Source EOP Width: TEOPT
Receiver EOP Width: TEOPR
Figure 9-4. Differential to EOP Transition Skew and EOP Width
Document #: 38-08026 Rev. *A
Page 21 of 25
CY7C63001A
CY7C63101A
TPERIOD
Differential
Crossover
Points
Data Lines
Consecutive
Transitions
N * TPERIOD + TxJR1
Paired
Transitions
N * TPERIOD + TxJR2
Figure 9-5. Differential Data Jitter
10.0
Ordering Information
EPROM
Number of
Package
Name
Operating
Range
Ordering Code
Size
4KB
4KB
4KB
4KB
4KB
4KB
4KB
4KB
GPIO
Package Type
20-Pin (300-Mil) PDIP
CY7C63001A-PC
CY7C63001A-PXC
CY7C63001A-SC
CY7C63001A-SXC
CY7C63101A-QC
CY7C63101A-QXC
CY7C63001A-XC
CY7C63001A-XWC
12
P5
P5
S5
S5
Q13
Q13
–
Commercial
Commercial
Commercial
Commercial
Commercial
Commercial
Commercial
Commercial
12
20-Pin (300-Mil) PDIP Lead-free
20-Pin (300-Mil) SOIC
12
12
20-Pin (300-Mil) SOIC Lead-free
24-Pin (150-Mil) QSOP
24-Pin (150-Mil) QSOP Lead-free
DIE Form
16
16
16
16
–
DIE Form Lead-free
11.0
Package Diagrams
20-Lead (300-Mil) Molded DIP P5
51-85011-*A
Document #: 38-08026 Rev. *A
Page 22 of 25
CY7C63001A
CY7C63101A
11.0
Package Diagrams (continued)
24-Lead Quarter Size Outline Q13
51-85055-*B
51-85024-*B
Document #: 38-08026 Rev. *A
Page 23 of 25
CY7C63001A
CY7C63101A
11.0
Package Diagrams (continued)
51-85025-*B
DIE FORM
4
3
2
1
24 23 22 21
5
20
19
18
17
6
7
8
Y
9
10 11 12 13 14 15 16
(0,0)
X
Table 11-1 below shows the die pad coordinates for the
CY7C63001A-XC and CY7C63001A-XWC. The center
location of each bond pad is relative to the bottom left corner
of the die which has coordinate (0,0).
Table 11-1. CY7C63001A-XC Probe Pad Coordinates in Microns ((0,0) to Bond Pad Centers)
Pin
X
Y
Pin
X
Y
Pad #
Name
(microns)
(microns)
Pad #
13
Name
(microns)
(microns)
1
2
Port00
Port01
Port02
Port03
Port10
Port12
Port14
Port16
Vss
676.00
507.35
338.70
170.05
120.10
120.10
120.10
120.10
148.50
278.30
414.25
653.45
2325.40
2325.40
2325.40
2325.40
2132.30
1962.90
1765.20
1595.80
121.80
Xtlout
Vcc
794.85
1033.55
1129.75
1451.70
1446.10
1446.10
1446.10
1446.10
1395.65
1227.00
1058.35
889.7
121.80
121.80
14
3
15
D-
121.80
4
16
D+
121.80
5
17
Port17
Port15
Port13
Port11
Port07
Port06
Port05
Port04
1595.80
1765.20
1962.90
2132.30
2325.40
2325.40
2325.40
2325.40
6
18
7
19
8
20
9
21
10
11
12
Vpp
121.80
22
Cext
121.80
23
Xtalin
121.80
24
All product and company names mentioned in this document are the trademarks of their respective holders.
Document #: 38-08026 Rev. *A
Page 24 of 25
© Cypress Semiconductor Corporation, 2004. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use
of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be
used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its
products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress
CY7C63001A
CY7C63101A
Document History Page
Document Title: CY7C63001A, CY7C63101A Universal Serial Bus Microcontroller
Document Number: 38-08026
Orig. of
REV.
**
ECN NO. Issue Date Change
Description of Change
116223
276070
06/12/02
See ECN
DSG
BON
Change from Spec number: 38-00662 to 38-08026
*A
Added die form and bond pad information. Added lead-free packages.
Removed obsolete packages and their references.
Document #: 38-08026 Rev. *A
Page 25 of 25
相关型号：
CY7C63221A-PXC
8-BIT, OTPROM, 12MHz, RISC MICROCONTROLLER, PDIP16, 0.300 INCH, LEAD FREE, PLASTIC, DIP-16
ROCHESTER
©2020 ICPDF网 联系我们和版权申明