MB3793-30APFV-XXX [CYPRESS]
Power Supply Management Circuit, BIPolar, PDSO8;
| 型号： | MB3793-30APFV-XXX |
| 厂家： | 
CYPRESS |
| 描述： | Power Supply Management Circuit, BIPolar, PDSO8 光电二极管 |
| 文件： | 总29页 (文件大小：529K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
The following document contains information on Cypress products.
FUJITSU MICROELECTRONICS
DATA SHEET
DS04-27406-5Ea
ASSP For Power Supply Applications
BIPOLAR
Power Voltage Monitoring IC
with Watchdog Timer
MB3793-30A
■ DESCRIPTION
The MB3793 is an integrated circuit to monitor power voltage; it incorporates a watchdog timer.
A reset signal is output when the power is cut or falls abruptly. When the power recovers normally after resetting,
a power-on reset signal is output to microprocessor units (MPUs). An internal watchdog timer with two inputs for
system operation diagnosis can provide a fall-safe function for various application systems.
There is also a mask option that can detect voltages of 4.9 V to 2.4 V in 0.1-V steps.
■ FEATURES
• Precise detection of power voltage fall: ± 2.5%
• Detection voltage with hysteresis
• Low power dispersion: ICC = 31 µA (reference)
• Internal dual-input watchdog timer
• Watchdog-timer halt function (by inhibition pin)
• Independently-set watchdog and reset times
• Three types of packages (SOP-8pin : 2 types, SSOP-8pin : 1 type)
■ APPLICATION
• Arcade Amusement etc.
Copyright©2003-2008 FUJITSU MICROELECTRONICS LIMITED All rights reserved
2006.5
MB3793-30A
■ PIN ASSIGNMENTS
(TOP VIEW)
1
2
3
4
8
7
6
5
CK1
CK2
INH
VCC
RESET
CTW
CTP
GND
(FPT-8P-M01)
(FPT-8P-M02)
(FPT-8P-M03)
■ PIN DESCRIPTION
Pin no. Symbol
Descriptions
Pin no. Symbol
Descriptions
Power supply pin
1
RESET Outputs reset pin
5
VCC
Watchdog timer monitor time
setting pin
2
CTW
6
INH
Inhibit pin
Power-on reset hold time set-
ting pin
3
4
CTP
7
8
CK2
CK1
Inputs clock 2 pin
Inputs clock 1 pin
GND
Ground pin
2
MB3793-30A
■ BLOCK DIAGRAM
5
To VCC of all blocks
VCC
.
.
I1 = 3 µA
I2 = 30 µA
.
.
CTP
3
1
.
R1 =
.
360 kΩ
Logic circuit
RESET
Output circuit
INH 6
Comp.S
−
VS
Reference
voltage
generator
CTW 2
CK1 8
Watchdog
timer
+
Pulse generator 1
.
VREF = 1.24 V
.
.
R2 =
.
240 kΩ
Pulse generator 2
To GND of
all blocks
7
CK2
4
GND
3
MB3793-30A
■ BLOCK DESCRIPTION
1. Comp. S
Comp. S is a comparator with hysteresis to compare the reference voltage with a voltage (VS) that is the result
of dividing the power voltage (VCC) by resistors 1 and 2. When VS falls below 1.24 V, a reset signal is output.
This function enables the MB3793 to detect an abnormality when the power is cut or falls abruptly.
2. Output circuit
The output circuit contains a RESET output control comparator that compares the voltage at the CTP pin to the
threshold voltage to release the RESET output if the CTP pin voltage exceeds the threshold value.
Since the reset (RESET) output buffer has CMOS organization, no pull-up resistor is needed.
3. Pulse generator
The pulse generator generates pulses when the voltage at the CK1 and CK2 clock pins changes to High from
Low level (positive-edge trigger) and exceeds the threshold voltage; it sends the clock signal to the watchdog
timer.
4. Watchdog timer
The watchdog timer can monitor two clock pulses. Short-circuit the CK1 and CK2 clock pins to monitor a single
clock pulse.
5. Inhibition pin
The inhibition (INH) pin forces the watchdog timer on/off. When this pin is High level, the watchdog timer is
stopped.
6. Logic circuit
The logic circuit contains flip-flops.
Flip-flop RSFF1 controls the charging and discharging of the power-on reset hold time setting capacitor (CTP).
Flip-flop RSFF2 turns on/off the circuit that accelerates charging of the power-on reset hold time setting capacitor
(CTP) at a reset. The RSFF2 operates only at a reset; it does not operate at a power-on reset when the power
is turned on.
4
MB3793-30A
■ ABSOLUTE MAXIMUM RATINGS
Rating
Parameter
Symbol
Conditions
Unit
Min
Max
+7
Power supply voltage*
VCC
VCK1
VCK2
IINH
−0.3
V
V
CK1
CK2
INH
VCC + 0.3
( ≤ +7)
Input voltage*
−0.3
VOL
VOH
VCC + 0.3
( ≤ +7)
Reset output voltage*
Reset output current
−0.3
−10
V
RESET
IOL
IOH
+10
mA
Power dissipation
PD
Ta ≤ +85 °C
200
mW
Storage temperature
Tstg
−55
+125
°C
* : The voltage is based on the ground voltage (0 V).
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
■ RECOMMENDED OPERATING CONDITIONS
Value
Parameter
Power supply voltage
Symbol
Conditions
Unit
V
Min
1.2
0
Typ
3.3
—
Max
6.0
+5
VCC
IOL
Reset (RESET) output current
mA
IOH
−5
—
0
Power-on reset hold time setting
capacity
CTP
0.001
0.1
10
µF
Watchdog-timer monitoring time
setting capacity*
CTW
Ta
0.001
0.01
1
µF
°C
Operating ambient temperature
−40
+25
+85
* : The watchdog timer monitor time range depends on the rating of the setting capacitor.
WARNING: The recommended operating conditions are required in order to ensure the normal operation of the
semiconductor device. All of the device’s electrical characteristics are warranted when the device is
operated within these ranges.
Always use semiconductor devices within their recommended operating condition ranges. Operation
outside these ranges may adversely affect reliability and could result in device failure.
No warranty is made with respect to uses, operating conditions, or combinations not represented on
the data sheet. Users considering application outside the listed conditions are advised to contact their
representatives beforehand.
5
MB3793-30A
■ ELECTRICAL CHARACTERISTICS
1. DC Characteristics
(VCC = +3.3 V, Ta = +25 °C)
Value
Unit
Parameter
Symbol
ICC
Conditions
After exit from reset
Min
Typ
Max
Power supply current
31
45
µA
Ta = +25 °C
2.93
3.00
3.00
3.07
3.07
3.07
VSL
VCC falling
V
Ta = −40 °C to +85 °C (2.89)*
Ta = +25 °C 3.00
(3.11)*
3.14
Detection voltage
VSH
VCC rising
VSH – VSL
V
Ta = −40 °C to +85 °C (2.96)*
(3.18)*
Detection voltage hysteresis
difference
VSHYS
30
70
110
mV
VCIH
VCIL
VCHYS
VIIH
VIIL
CK rising
CK falling
(0.7)*
0.5
1.3
1.0
0.3
1.9
(1.5)*
(0.6)*
VCC
0.8
V
V
V
Clock-input threshold voltage
Clock-input hysteresis
(0.1)*
2.2
0
Inhibition-input voltage
V
IIH
VCK = 5 V
0
1.0
µA
µA
V
Input current
(CK1, CK2, INH)
IIL
VCK = 0 V
−1.0
2.8
0
VOH
VOL
IRESET = −3 mA
IRESET = +3 mA
3.10
0.12
Reset output voltage
0.4
V
Reset-outputminimumpower
voltage
VCCL
IRESET = +50 µA
0.8
1.2
V
* : The values enclosed in parentheses ( ) are setting assurance values.
2. AC Characteristics
(VCC = +3.3 V, Ta = +25 °C)
Value
Unit
Parameter
Symbol
Conditions
Min
Typ
Max
Power-on reset hold time
tPR
CTP = 0.1 µF
30
75
120
ms
ms
CTW = 0.01 µF,
CTP = 0.1 µF
Watchdog timer monitor time
tWD
8
16
24
Watchdog timer reset time
Clock input pulse width
Clock input pulse cycle
tWR
tCKW
tCKT
tr*
CTP = 0.1 µF
2
500
20
5.5
9
ms
ns
µs
ns
ns
Rising
Falling
CL = 50 pF
CL = 50 pF
500
500
Reset (RESET) output transition
time
tf*
* : The voltage range is 10% to 90% at testing the reset output transition time.
6
MB3793-30A
■ DIAGRAM
1. Basic operation (Positive clock pulse)
VSH
VSL
VCC
tCKW
CK1
CK2
INH
tCKT
Vth
CTP
VH
VL
CTW
RESET
tPR
tWD
tPR
tWR
(1) (2) (3) (4)(5) (5)
(6) (7)
(8) (9)
(10)
(11)
(12)
(13)
7
MB3793-30A
2. Basic operation (Negative clock pulse)
VSH
VSL
VCC
tCKW
CK1
CK2
INH
tCKT
Vth
CTP
VH
VL
CTW
RESET
tPR
tWD
tPR
tWR
(1) (2) (3) (4)(5) (5)
(6) (7)
(8) (9)
(10)
(11)
(12)
(13)
8
MB3793-30A
3. Single-clock input monitoring (Positive clock pulse)
tCKW
CK1
CK2
tCKT
Vth
CTP
VH
VL
CTW
RESET
tWD
tWR
Note : The MB3793 can monitor only one clock.
The MB3793 checks the clock signal at every other input pulse.
Therefore, set watchdog timer monitor time tWD to the time that allows the MB3793
to monitor the period twice as long as the input clock pulse.
9
MB3793-30A
4. Inhibition operation (Positive clock pulse)
VSH
VSL
VCC
tCKW
CK1
tCKT
CK2
INH
Vth
CTP
VH
CTW
VL
RESET
tPR
tWD
tPR
tWR
(1) (2) (3) (4)(5) (5)
(6) (7) (11) (8) (9)
(10)
(12)
(13)
10
MB3793-30A
5. Clock pulse input supplementation (Positive clock pulse)
tCKT
tCKW
1
*
CK1
2
*
CK2
VH
CTW
VL
Note : The MB3793 watchdog timer monitors Clock1 (CK1) and Clock2 (CK2) pulses alternately.
When a CK2 pulse is detected after detecting a CK1 pulse, the monitoring time setting capacity
(CTW) switches to charging from discharging.
When two consecutive pulses occur on one side of this alternation before switching, the second
pulse is ignored.
In the above figure, pulse *1 and *2 are ignored.
11
MB3793-30A
■ OPERATION SEQUENCE
1. Positive clock pulse input
Refer to “1. Basic operation (positive clock pulse)” under “■ DIAGRAM.”
2. Negative clock pulse input
Refer to “2. Basic operation (negative clock pulse)” under “■ DIAGRAM.”
The MB3793 operates in the same way whether it inputs positive or negative pulses.
3. Clock monitoring
To use the MB3793 while monitoring only one clock, connect clock pins CK1 and CK2.
Although the MB3793 operates basically in the same way as when monitoring two clocks, it monitors the clock
signal at every other input pulse.
Refer to “3. Single-clock input monitoring (positive clock pulse)” under “■ DIAGRAM.”
4. Description of Operations
The numbers given to the following items correspond to numbers (1) to (13) used in “■ DIAGRAM.”
(1) The MB3793 outputs a reset signal when the supply voltage (VCC) reaches about 0.8 V (VCCL)
(2) If VCC reaches or exceeds the rise-time detected voltage VSH, the MB3793 starts charging the power-on
reset hold time setting capacitor CTP. At this time, the output remains in a reset state. The VSH value is
3.07 V (Typ) .
(3) When CTP has been charged for a certain period of time TPR (until the CTP pin voltage exceeds the
threshold voltage (Vth) after the start of charging), the MB3793 cancels the reset (setting the RESET pin
to “H” level from “L” level).
The Vth value is about 2.4 V with VCC = 3.3 V
The power-on reset hold time tPR is set with the following equation:
.
tPR (ms) = A × CTP (µF)
.
The value of A is about 750 with VCC = 3.3 V. The MB3793 also starts charging the watchdog timer
monitor time setting capacitor (CTW).
(4) When the voltage at the watchdog timer monitor time setting pin CTW reaches the “H” level threshold
voltage VH, the CTW switches from the charge state to the discharge state.
The value of VH is always about 1.24 V regardless of the detected voltage.
(5) If the CK2 pin inputs a clock pulse (positive edge trigger) when the CTW is being discharged in the
CK1-CK2 order or simultaneously, the CTW switches from the discharge state to the charge state.
The MB3793 repeats operations (4) and (5) as long as the CK1/CK2 pin inputs clock pulses with the
system logic circuit operating normally.
(6) If no clock pulse is fed to the CK1 or CK2 pin within the watchdog timer monitor time tWD due to some
problem with the system logic circuit, the CTW pin is set to the “L” level threshold voltage VL or less and
the MB3793 outputs a reset signal (setting the RESET pin to “L” level from “H” level).
The value of VL is always about 0.24 V regardless of the detected voltage.
The watchdog timer monitor time tWD is set with the following equation:
.
tWD (ms) = B × CTW (µF)
.
The value of B is hardly affected by the power supply voltage; it is about 1600 with VCC = 3.3 V.
(Continued)
12
MB3793-30A
(Continued)
(7) When a certain period of time tWR has passed (until the CTP pin voltage reaches or exceeds Vth again
after recharging the CTP), the MB3793 cancels the reset signal and starts operating the watchdog timer.
The watchdog timer monitor reset time tWR is set with the following equation:
.
tWR (ms) = D x CTP (µF)
.
The value of D is 55 with VCC = 3.3 V.
The MB3793 repeats operations (4) and (5) as long as the CK1/CK2 pin inputs clock pulses. If no clock
pulse is input, the MB3793 repeats operations (6) and (7).
(8) If VCC is lowered to the fall-time detected voltage (VSL) or less, the CTP pin voltage decreases and the
MB3793 outputs a reset signal (setting the RESET pin to “L” level from “H” level).
The value of VSL is 3.0 V (Typ) .
(9) When VCC reaches or exceeds VSH again, the MB3793 starts charging the CTP.
(10) When the CTP pin voltage reaches or exceeds Vth, the MB3793 cancels the reset and restarts operating
the watchdog timer. It repeats operations (4) and (5) as long as the CK1/CK2 pin inputs clock pulses.
(11) Making the inhibit pin active (setting the INH pin to “H” from “L”) forces the watchdog timer to stop
operation.
This stops only the watchdog timer, leaving the MB3793 monitoring VCC (operations (8) to (10)).
The watchdog timer remains inactive unless the inhibit input is canceled.
The inhibition (INH) pin must be connecting a voltage of more low impedance, to evade of the noise.
(12) Canceling the inhibit input (setting the INH pin to “L” from “H”) restarts the watchdog timer.
(13) The reset signal is output when the power supply is turned off to set VCC to VSL or less.
1. Equation of time-setting capacitances (CTP and CTW) and set time
.
=
tPR [ms]
tWD [ms]
tWR [ms]
A × CTP [µF]
B × CTW [µF]
D × CTP [µF]
.
.
=
.
.
=
.
Values of A, B, C, and D
A
B
C
0
0
D
Remark
750
1300
1600
1500
55
VCC = 3.3 V
VCC = 5.0 V
100
2. Example (when CTP = 0.1 µF and CTW = 0.01 µF)
Symbol
tPR
VCC = 3.3 V
VCC = 5.0 V
75
16
130
15
time
(ms)
tWD
tWR
5.5
10
13
MB3793-30A
■ TYPICAL CHARACTERISTICS
Power supply current vs.
Detection voltage vs.
Power supply voltage
Operating ambient temperature
50
3.12
3.10
3.08
3.06
3.04
3.02
3.00
2.98
2.96
Watchdog timer monitoring
45
(VINH = 0 V)
40
VSH
35
30
Watchdog timer stopping
25
20
15
10
5
(VINH = VCC
)
VSL
f = 1 kHz
Duty = 10 %
CK1 = CK2
0
0
1
7
6
2
3
4
5
8
−40 −20
0
+20 +40 +60 +80 +100 +120
Power supply voltage VCC (V)
Operating ambient temperature Ta ( °C)
Reset output voltage vs. Reset output current
(P-MOS side)
Reset output voltage vs. Reset output current
(N-MOS side)
3.3
600
at VCC
= 3.3 V
at VCC = 3.3 V
Ta = +85 ˚C
3.2
3.1
3.0
2.9
2.8
2.7
2.6
2.5
2.4
2.3
500
Ta = +25 ˚C
400
Ta = −40 ˚C
Ta = −40 ˚C
300
Ta = +25 ˚C
Ta = +85 ˚C
200
100
0
0
1
2
3
4
5
6
7
8
9
10
0
−1 −2 −3 −4 −5 −6 −7 −8 −9 −10
Reset output current IRESET (mA)
Reset output current IRESET (mA)
Note : Without writing the value clearly, VCC = 3.3 (V), CTP = 0.1 (µF), CTW = 0.01 (µF).
(Continued)
14
MB3793-30A
Power-on reset hold time vs.
Operating ambient temperature (When VCC rising)
Reset output voltage vs. Power supply voltage
7
200
at VCC = 3.3 V
180
Pull-up resistance 100 kΩ
6
160
140
120
100
80
5
4
3
Ta = +85 ˚C
60
2
40
Ta = +25 ˚C
1
20
Ta = −40 ˚C
0
0
−40 −20
0
+20 +40 +60 +80 +100 +120
0
1
2
3
4
5
6
7
Power supply voltage VCC (V)
Operating ambient temperature Ta ( °C)
Watchdog timer reset time vs. Operating ambient
temperature (When monitoring)
Watchdog timer monitoring time vs.
Operating ambient temperature
26
26
at VCC = 3.3 V
at VCC = 3.3 V
24
22
20
18
16
14
12
10
8
24
22
20
18
16
14
12
10
8
6
6
4
4
2
2
0
0
−40 −20
0
+20 +40 +60 +80 +100 +120
−40 −20
0
+20 +40 +60 +80 +100 +120
Operating ambient temperature Ta ( °C)
Operating ambient temperature Ta ( °C)
(Continued)
15
MB3793-30A
(Continued)
Watchdog timer reset time vs.
CTP capacitance
Power-on reset hold time vs.
CTP capacitance
103
102
101
104
103
102
101
Ta = −40 °C
Ta = −40 °C
Ta = +25 °C
1
10−1
10−2
Ta = +25 °C
Ta = +85 °C
Ta = +85 °C
1
10 −1
10−4 10−3 10−2 10−1
1
101
102
10−4 10−3 10−2 10−1
1
101
102
Power-on reset hold time
setting capacitance CTP (µF)
Power-on reset hold time
setting capacitance CTP (µF)
Watchdog timer monitoring time vs.
CTW capacitance
103
Ta = −40 °C
102
Ta = +25 °C
101
1
Ta = +85 °C
10−1
10−5 10−4 10−3 10−2 10−1
1
101
Watchdog timer monitoring time
setting capacitance CTW (µF)
16
MB3793-30A
■ APPLICATION EXAMPLE
1. (1) Supply voltage monitor and watchdog timer (1-clock monitor)
VCC
5
VCC
2
CTW
RESET
1
MB3793
RESET
VCC
CTP
INH
CK1
CK2
3
6
8
7
CTW*
CTP*
Microprocessor
CK
GND
4
GND
GND
* : Use a capacitor with less leakage current.
The MB3793 monitors the clock (CK1, CK2) at every other input pulse.
(2) Supply voltage monitor and watching timer (2-clock monitor)
VCC
5
VCC
2
1
CTW
RESET
RESET
VCC
RESET
VCC
MB3793
Microprocessor 1
Microprocessor 2
CTW*
CTP*
3
6
8
7
CTP
INH
CK1
CK
CK
GND
GND
GND CK2
4
GND
* : Use a capacitor with less leakage current.
17
MB3793-30A
2. Supply voltage monitor and watchdog timer stop
VCC
5
VCC
6
INH
RESET 1
RESET
VCC
RESET
VCC
MB3793
Microprocessor 1
Microprocessor 2
2
3
HALT
GND
CTW
CK1
CK
8
CK
HALT
GND
CTW*
CTP*
GND
4
CTP
CK2 7
GND
* : Use a capacitor with less leakage current.
■ NOTES ON USE
• Take account of common impedance when designing the earth line on a printed wiring board.
• Take measures against static electricity.
- For semiconductors, use antistatic or conductive containers.
- When storing or carrying a printed circuit board after chip mounting, put it in a conductive bag or container.
- The work table, tools and measuring instruments must be grounded.
- The worker must put on a grounding device containing 250 kΩ to 1 MΩ resistors in series.
• Do not apply a negative voltage.
- Applying a negative voltage of −0.3 V or less to an LSI may generate a parasitic transistor, resulting in
malfunction.
18
MB3793-30A
■ ORDERING INFORMATION
Part number
Package
Marking
Remarks
MB3793-30APF-■■■
8-pin Plastic SOP
(FPT-8P-M01)
3793AN
conventional version
MB3793-30APNF-■■■
8-pin Plastic SOP
(FPT-8P-M02)
3793AN
93AN
conventional version
conventional version
Lead Free version
Lead Free version
Lead Free version
MB3793-30APFV-■■■
MB3793-30APF-■■■E1
MB3793-30APNF-■■■E1
MB3793-30APFV-■■■E1
8-pin Plastic SSOP
(FPT-8P-M03)
8-pin Plastic SOP
(FPT-8P-M01)
3793AN
3793AN
93AN
8-pin Plastic SOP
(FPT-8P-M02)
8-pin Plastic SSOP
(FPT-8P-M03)
■ RoHS Compliance Information of Lead (Pb) Free version
The LSI products of Fujitsu Microelectronics with “E1” are compliant with RoHS Directive , and has observed
the standard of lead, cadmium, mercury, Hexavalent chromium, polybrominated biphenyls (PBB) , and polybro-
minated diphenyl ethers (PBDE) .
The product that conforms to this standard is added “E1” at the end of the part number.
19
MB3793-30A
■ MARKING FORMAT (Lead Free version)
Lead Free version
3793AN
E1XXXX
XXX
SOP-8
(FPT-8P-M01)
INDEX
3793AN
XXXX
E1 XXX
Lead Free version
SOP-8
(FPT-8P-M02)
Lead Free version
93AN
1 XXX
XXX
SSOP-8
(FPT-8P-M03)
INDEX
20
MB3793-30A
■ LABELING SAMPLE (Lead free version)
lead-free mark
JEITA logo JEDEC logo
MB123456P - 789 - GE1
(3N) 1MB123456P-789-GE1 1000
G
Pb
(3N)2 1561190005 107210
QC PASS
PCS
1,000
MB123456P - 789 - GE1
ASSEMBLED IN JAPAN
2006/03/01
MB123456P - 789 - GE1
1/1
1561190005
0605 - Z01A 1000
Lead Free version
21
MB3793-30A
■ MB3793-30APF-■■■E1, MB3793-30APNF-■■■E1, MB3793-30APFV-■■■
Recommended Conditions of Moisture Sensitivity Level
Item
Condition
IR (infrared reflow) , Manual soldering (partial heating method)
2 times
Mounting Method
Mounting times
Please use it within two years after
Before opening
Manufacture.
From opening to the 2nd
Less than 8 days
reflow
Storage period
When the storage period after
opening was exceeded
Please processes within 8 days
after baking (125 °C, 24h)
Storage conditions
5 °C to 30 °C, 70%RH or less (the lowest possible humidity)
[Temperature Profile for FJ Standard IR Reflow]
(1) IR (infrared reflow)
H rank : 260 °C Max.
260 °C
255 °C
170 °C
to
190 °C
(b)
(c)
(d)
(e)
RT
(a)
(d')
(a) Temperature Increase gradient : Average 1 °C/s to 4 °C/s
(b) Preliminary heating : Temperature 170 °C to 190 °C, 60s to 180s
(c) Temperature Increase gradient : Average 1 °C/s to 4 °C/s
(d) Actual heating
(d’)
: Temperature 260 °C MAX; 255 °C or more, 10s or less
: Temperature 230 °C or more, 40s or less
or
Temperature 225 °C or more, 60s or less
or
Temperature 220 °C or more, 80s or less
(e) Cooling
: Natural cooling or forced cooling
Note : Temperature : the top of the package body
(2) Manual soldering (partial heating method)
Conditions : Temperature 400 °C MAX
Times : 5 s max/pin
22
MB3793-30A
■ PACKAGE DIMENSIONS
8-pin plastic SOP
Lead pitch
1.27 mm
5.3 × 6.35 mm
Gullwing
Package width
package length
×
Lead shape
Sealing method
Mounting height
Weight
Plastic mold
2.25 mm MAX
0.10 g
Code
(Reference)
P-SOP8-5.3×6.35-1.27
(FPT-8P-M01)
8-pin plastic SOP
(FPT-8P-M01)
Note 1) *1 : These dimensions include resin protrusion.
Note 2) *2 : These dimensions do not include resin protrusion.
Note 3) Pins width and pins thickness include plating thickness.
Note 4) Pins width do not include tie bar cutting remainder.
*
1 6.35 –+00..2205 .250 –+..000180
0.17 –+00..0043
.007 +–..000021
8
5
*2 5.30±0.30 7.80±0.40
(.209±.012) (.307±.016)
INDEX
Details of "A" part
2.00 +–00..1255
(Mounting height)
.079 +–..000160
0.25(.010)
0~8˚
"A"
1
4
1.27(.050)
0.47±0.08
(.019±.003)
M
0.13(.005)
0.50±0.20
(.020±.008)
0.10 +–00..0150
.004 +–..000024
0.60±0.15
(Stand off)
(.024±.006)
0.10(.004)
Dimensions in mm (inches).
Note: The values in parentheses are reference values.
C
2002 FUJITSU LIMITED F08002S-c-6-7
(Continued)
23
MB3793-30A
8-pin plastic SOP
Lead pitch
1.27 mm
3.9 × 5.05 mm
Gullwing
Package width
package length
×
Lead shape
Sealing method
Mounting height
Weight
Plastic mold
1.75 mm MAX
0.06 g
(FPT-8P-M02)
8-pin plastic SOP
(FPT-8P-M02)
Note 1) *1 : These dimensions include resin protrusion.
Note 2) *2 : These dimensions do not include resin protrusion.
Note 3) Pins width and pins thickness include plating thickness.
Note 4) Pins width do not include tie bar cutting remainder.
+0.25
1 5.05 –0.20 .199 +–..000180
0.22 –+00..0073
.009 +–..000031
*
8
5
*2 3.90±0.30 6.00±0.40
(.154±.012) (.236±.016)
Details of "A" part
45˚
1.55±0.20
(Mounting height)
(.061±.008)
0.25(.010)
0.40(.016)
0~8˚
"A"
1
4
1.27(.050)
0.44±0.08
(.017±.003)
M
0.13(.005)
0.50±0.20
(.020±.008)
0.15±0.10
(.006±.004)
(Stand off)
0.60±0.15
(.024±.006)
0.10(.004)
Dimensions in mm (inches).
Note: The values in parentheses are reference values.
C
2002 FUJITSU LIMITED F08004S-c-4-7
(Continued)
24
MB3793-30A
(Continued)
8-pin plastic SSOP
Lead pitch
0.80 mm
4.2 × 3.5 mm
Gullwing
Package width
package length
×
Lead shape
Sealing method
Mounting height
Weight
Plastic mold
1.45 mm MAX
0.04 g
Code
(Reference)
P-SSOP8-4.2×3.5-0.80
(FPT-8P-M03)
8-pin plastic SSOP
Note 1) *1 : Resin protrusion. (Each side : +0.15 (.006) Max).
Note 2) *2 : These dimensions do not include resin protrusion.
Note 3) Pins width and pins thickness include plating thickness.
Note 4) Pins width do not include tie bar cutting remainder.
0.17 +–00..0043
(FPT-8P-M03)
13.50±0.10(.138±.004)
*
.007 +–..000021
8
5
*24.20±0.10 6.20±0.20
(.165±.004) (.244±.008)
INDEX
Details of "A" part
1.25 +–00..1200
(Mounting height)
.049 –+..000048
0.25(.010)
"A"
0~8˚
1
4
0.80(.031)
0.37±0.08
(.015±.003)
M
0.10(.004)
0.50±0.20
(.020±.008)
0.10±0.10
(.004±.004)
(Stand off)
0.60±0.15
(.024±.006)
0.10(.004)
Dimensions in mm (inches).
Note: The values in parentheses are reference values.
C
2002 FUJITSU LIMITED F08005S-c-3-5
25
MB3793-30A
MEMO
26
MB3793-30A
MEMO
27
FUJITSU MICROELECTRONICS LIMITED
Shinjuku Dai-Ichi Seimei Bldg. 7-1, Nishishinjuku 2-chome, Shinjuku-ku,
Tokyo 163-0722, Japan
Tel: +81-3-5322-3347 Fax: +81-3-5322-3387
http://jp.fujitsu.com/fml/en/
For further information please contact:
North and South America
Asia Pacific
FUJITSU MICROELECTRONICS AMERICA, INC.
1250 E. Arques Avenue, M/S 333
Sunnyvale, CA 94085-5401, U.S.A.
Tel: +1-408-737-5600 Fax: +1-408-737-5999
http://www.fma.fujitsu.com/
FUJITSU MICROELECTRONICS ASIA PTE LTD.
151 Lorong Chuan, #05-08 New Tech Park,
Singapore 556741
Tel: +65-6281-0770 Fax: +65-6281-0220
http://www.fujitsu.com/sg/services/micro/semiconductor/
Europe
FUJITSU MICROELECTRONICS SHANGHAI CO., LTD.
Rm.3102, Bund Center, No.222 Yan An Road(E),
Shanghai 200002, China
FUJITSU MICROELECTRONICS EUROPE GmbH
Pittlerstrasse 47, 63225 Langen,
Germany
Tel: +86-21-6335-1560 Fax: +86-21-6335-1605
http://cn.fujitsu.com/fmc/
Tel: +49-6103-690-0 Fax: +49-6103-690-122
http://emea.fujitsu.com/microelectronics/
FUJITSU MICROELECTRONICS PACIFIC ASIA LTD.
10/F., World Commerce Centre, 11 Canton Road
Tsimshatsui, Kowloon
Korea
FUJITSU MICROELECTRONICS KOREA LTD.
206 KOSMO TOWER, 1002 Daechi-Dong,
Kangnam-Gu,Seoul 135-280
Korea
Hong Kong
Tel: +852-2377-0226 Fax: +852-2376-3269
http://cn.fujitsu.com/fmc/tw
Tel: +82-2-3484-7100 Fax: +82-2-3484-7111
http://www.fmk.fujitsu.com/
All Rights Reserved.
The contents of this document are subject to change without notice.
Customers are advised to consult with sales representatives before ordering.
The information, such as descriptions of function and application circuit examples, in this document are presented solely for the purpose
of reference to show examples of operations and uses of FUJITSU MICROELECTRONICS device; FUJITSU MICROELECTRONICS
does not warrant proper operation of the device with respect to use based on such information. When you develop equipment incorporat-
ing the device based on such information, you must assume any responsibility arising out of such use of the information.
FUJITSU MICROELECTRONICS assumes no liability for any damages whatsoever arising out of the use of the information.
Any information in this document, including descriptions of function and schematic diagrams, shall not be construed as license of the use
or exercise of any intellectual property right, such as patent right or copyright, or any other right of FUJITSU MICROELECTRONICS
or any third party or does FUJITSU MICROELECTRONICS warrant non-infringement of any third-party's intellectual property right or
other right by using such information. FUJITSU MICROELECTRONICS assumes no liability for any infringement of the intellectual
property rights or other rights of third parties which would result from the use of information contained herein.
The products described in this document are designed, developed and manufactured as contemplated for general use, including without
limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured
as contemplated (1) for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect
to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in
nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in
weapon system), or (2) for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite).
Please note that FUJITSU MICROELECTRONICS will not be liable against you and/or any third party for any claims or damages arising
in connection with above-mentioned uses of the products.
Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by
incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current
levels and other abnormal operating conditions.
Exportation/release of any products described in this document may require necessary procedures in accordance with the regulations of
the Foreign Exchange and Foreign Trade Control Law of Japan and/or US export control laws.
The company names and brand names herein are the trademarks or registered trademarks of their respective owners.
Edited Strategic Business Development Dept.
相关型号：
MB3793-30APFV-XXXE1
Power Supply Management Circuit, Fixed, 1 Channel, BIPolar, PDSO8, 4.20 X 3.50 MM, 1.45 MM HEIGHT, 0.80 MM PITCH, ROHS COMPLIANT, PLASTIC, SSOP-8
FUJITSU
MB3793-30APNF-XXX
Power Supply Management Circuit, Fixed, 1 Channel, BIPolar, PDSO8, 3.90 X 5.05 MM, 1.75 MM HEIGHT, 1.27 MM PITCH, PLASTIC, SOP-8
FUJITSU
MB3793-30APNF-XXXE1
Power Supply Management Circuit, Fixed, 1 Channel, BIPolar, PDSO8, 3.90 X 5.05 MM, 1.75 MM HEIGHT, 1.27 MM PITCH, ROHS COMPLIANT, PLASTIC, SOP-8
FUJITSU
MB3793-34APNF
Power Supply Management Circuit, Fixed, 1 Channel, BIPolar, PDSO8, 3.90 X 5.05 MM, 1.75 MM HEIGHT, 1.27 MM PITCH, PLASTIC, SOP-8
FUJITSU
©2020 ICPDF网 联系我们和版权申明