MT54W2MH8JF-6 [CYPRESS]
QDR SRAM, 2MX8, 0.5ns, CMOS, PBGA165, 13 X 15 MM, 1 MM PITCH, FBGA-165;型号: | MT54W2MH8JF-6 |
厂家: | CYPRESS |
描述: | QDR SRAM, 2MX8, 0.5ns, CMOS, PBGA165, 13 X 15 MM, 1 MM PITCH, FBGA-165 时钟 静态存储器 内存集成电路 |
文件: | 总28页 (文件大小:413K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
2 MEG x 8, 1 MEG x 18, 512K x 36
1.8V VDD, HSTL, QDRIIb4 SRAM
MT54W2MH8J
MT54W1MH18J
MT54W512H36J
18Mb QDR™II SRAM
4-WORD BURST
Features
•
•
DLL circuitry for accurate output data placement
Separate independent read and write data ports with
concurrent transactions
Figure 1: 165-Ball FBGA
•
100 percent bus utilization DDR READ and WRITE
operation
•
•
•
•
•
Fast clock to valid data times
Full data coherency, providing most current data
Four-tick burst counter for reduced-address frequency
Double data rate operation on read and write ports
Two input clocks (K and K#) for precise DDR timing at
clock rising edges only
•
•
Two output clocks (C and C#) for precise flight time
and clock skew matching—clock and data delivered
together to receiving device
Optional-use echo clocks (CQ and CQ#) for flexible
receive data synchronization
Table 1:
Valid Part Numbers
•
•
•
•
Single address bus
Simple control logic for easy depth expansion
Internally self-timed, registered writes
Core VDD = 1.8V ( 0.1V); I/O VDDQ = 1.5V to VDD
( 0.1V) HSTL
Clock-stop capability with µs restart
13mm x 15mm, 1mm pitch, 11 x 15 grid FBGA package
User-programmable impedance output
JTAG boundary scan
PART NUMBER
DESCRIPTION
MT54W2MH8JF-xx
MT54W1MH18JF-xx
MT54W512H36JF-xx
2 Meg x 8,QDRIIb4 FBGA
1 Meg x 18, QDRIIb4 FBGA
512K x 36, QDRIIb4 FBGA
•
•
•
•
General Description
The Micron® QDR™II (Quad Data Rate™) synchro-
nous, pipelined burst SRAM employs high-speed, low-
power CMOS designs using an advanced 6T CMOS
process.
Options
•
Marking1
Clock Cycle Timing
3ns (333 MHz)
3.3ns (300 MHz)
4ns (250 MHz)
5ns (200 MHz)
6ns (167 MHz)
7.5ns (133 MHz)
Configurations
2 Meg x 8
1 Meg x 18
512K x 36
-3
-3.3
-4
-5
-6
The QDR architecture consists of two separate DDR
(double data rate) ports to access the memory array.
The read port has dedicated data outputs to support
READ operations. The write port has dedicated data
inputs to support WRITE operations. This architecture
eliminates the need for high-speed bus turnaround.
Access to each port is accomplished using a common
address bus. Addresses for reads and writes are latched
on alternate rising edges of the K clock. Each address
location is associated with four words that burst
sequentially into or out of the device. Since data can be
transferred into and out of the device on every rising
edge of both clocks (K and K# and C and C#) memory
bandwidth is maximized and system design is simpli-
fied by eliminating bus turnarounds.
-7.5
•
MT54W2MH8J
MT54W1MH18J
MT54W512H36J
•
•
Package
165-ball, 13mm x 15mm FBGA
Operating Temperature Range
Commercial (0°C ? TA ? +70°C)
F
None
NOTE:
1. A Part Marking Guide for the FBGA devices can be found on
Micron’s Web site—http://www.micron.com/numberguide.
18Mb: 1.8V VDD, HSTL, QDRIIb4 SRAM
MT54W1MH18J_H.fm – Rev. H, Pub. 3/03
©2003 Micron Technology, Inc.
1
2 MEG x 8, 1 MEG x 18, 512K x 36
1.8V VDD, HSTL, QDRIIb4 SRAM
Depth expansion is accomplished with port selects
for each port (read R#, write W#) which are received at
K rising edge. Port selects permit independent port
operation.
READ cycles are pipelined. The request is initiated
by asserting R# LOW at K rising edge. Data is delivered
after the next rising edge of K# (t + 1), using C and C#
as the output timing references, or using K and K# if C
and C# are tied HIGH. If C and C# are tied HIGH, they
may not be toggled during device operation. Output
tri-stating is automatically controlled such that the bus
is released if no data is being delivered. This permits
banked SRAM systems with no complex output enable
(OE) timing generation. Back-to-back READ cycles are
initiated every K rising edge. Any read request in
between is ignored, since the burst sequence may not
be interrupted and requires two full clock cycles.
WRITE cycles are initiated by W# LOW at K rising
edge. Data is expected at both rising edges of K and K#,
beginning one clock period later. Write registers are
incorporated to facilitate pipelined self-timed WRITE
cycles and provide fully coherent data for all combina-
tions of reads and writes. A read can immediately fol-
low a write even if they are to the same address.
Although the write data has not been written to the
memory array, the SRAM will deliver the data from the
write register instead of using the older data from the
memory array. The latest data is always utilized for all
bus transactions. WRITE cycles are initiated every sec-
ond K rising edge. Any in-between WRITE request is
ignored, since the burst sequence may not be inter-
rupted.
All synchronous inputs pass through registers con-
trolled by the K or K# input clock rising edges. Active
LOW byte writes (BWx#) permit byte write or nibble
write selection. Write data and byte writes are regis-
tered on the rising edges of both K and K#. The
addressing within each burst of four is fixed and
sequential, beginning with the lowest and ending with
the highest address. All synchronous data outputs pass
through output registers controlled by the rising edges
of the output clocks (C and C# if provided, otherwise K
and K#).
Four balls are used to implement JTAG test capabili-
ties: test mode select (TMS), test data-in (TDI), test
clock (TCK), and test data-out (TDO). JTAG circuitry is
used to serially shift data to and from the SRAM. JTAG
inputs use JEDEC-standard 1.8V I/O levels to shift data
during this testing mode of operation.
The SRAM operates from a 1.8V power supply, and
all inputs and outputs are HSTL-compatible. The
device is ideally suited for applications that benefit
from a high-speed, fully-utilized DDR data bus.
Please refer to Micron’s Web site (www.micron.com/
sramds) for the latest data sheet.
READ/WRITE Operations
All bus transactions operate on an uninterruptable
burst of four data, requiring one full clock cycle of bus
utilization. Any request that attempts to interrupt a
burst-in-progress is ignored. The resulting benefit is
that the address rate is kept down to the clock fre-
quency even when both buses are 100 percent utilized.
PARTIAL WRITE Operations
BYTE WRITE operations are supported, except for
x8 devices in which nibble write is supported. The
active LOW write controls, BWx# (NWx#), are regis-
tered coincident with their corresponding data. This
feature can eliminate the need for some READ-MOD-
IFY-WRITE cycles, collapsing it to a single BYTE/NIB-
BLE WRITE operation in some instances.
18Mb: 1.8V VDD, HSTL, QDRIIb4 SRAM
MT54W1MH18J_H.fm – Rev. H, Pub. 3/03
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2003 Micron Technology, Inc.
2
2 MEG x 8, 1 MEG x 18, 512K x 36
1.8V VDD, HSTL, QDRIIb4 SRAM
automatically resets the DLL when the absence of
input clock is detected. See Micron Technical Note TN-
54-02 for more information on clock DLL start-up pro-
cedures.
Programmable Impedance Output
Buffer
The QDR SRAM is equipped with programmable
impedance output buffers. This allows a user to match
the driver impedance to the system. To adjust the
impedance, an external precision resistor (RQ) is con-
nected between the ZQ ball and VSS. The value of the
resistor must be five times the desired impedance. For
example, a 350ꢀ resistor is required for an output
impedance of 70ꢀ. To ensure that output impedance
is one-fifth the value of RQ (within 15 percent), the
range of RQ is 175ꢀ to 350ꢀ. Alternately, the ZQ ball
can be connected directly to VDDQ, which will place
the device in a minimum impedance mode.
Single Clock Mode
The SRAM can be used with the single K, K# clock
pair by tying C and C# HIGH. In this mode, the SRAM
will use K and K# in place of C and C#. This mode pro-
vides the most rapid data output but does not com-
pensate for system clock skew and flight times.
The output echo clocks are precise references to
output data. CQ and CQ# are both rising edge and fall-
ing edge accurate and are 180° out of phase. Either or
both may be used for output data capture. K or C rising
edge triggers CQ rising and CQ# falling edge. CQ rising
edge indicates first data response for QDRI and DDRI
(version 1, non-DLL) SRAM, while CQ# rising edge
indicates first data response for QDRII and DDRII (ver-
sion 2, DLL) SRAM.
Output impedance updates may be required
because over time variations may occur in supply volt-
age and temperature. The device samples the value of
RQ. Impedance updates are transparent to the system;
they do not affect device operation, and all data sheet
timing and current specifications are met during an
update.
The device will power up with an output impedance
set at 50ꢀ. To guarantee optimum output driver
impedance after power-up, the SRAM needs 1,024
cycles to update the impedance. The user can operate
the part with fewer than 1,024 clock cycles, but optimal
output impedance is not guaranteed.
Depth Expansion
Port select inputs are provided for the read and
write ports. This allows for easy depth expansion. Both
port selects are sampled on the rising edge of K only.
Each port can be independently selected and dese-
lected and does not affect the operation of the oppo-
site port. All pending transactions are completed prior
to a port deselect. Depth expansion requires replicat-
ing R# and W# control signals for each bank if it is
desired to have bank independent READ and WRITE
operations.
Clock Considerations
The device utilizes internal delay-locked loops for
maximum output, data valid window. It can be placed
into a stopped-clock state to minimize power with a
modest restart time of 1,024 clock cycles. Circuitry
18Mb: 1.8V VDD, HSTL, QDRIIb4 SRAM
MT54W1MH18J_H.fm – Rev. H, Pub. 3/03
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2003 Micron Technology, Inc.
3
2 MEG x 8, 1 MEG x 18, 512K x 36
1.8V VDD, HSTL, QDRIIb4 SRAM
Figure 2: Functional Block Diagram
2 Meg x 8; 1 Meg x 18; 512K x 36
n
n
ADDRESS
R#
ADDRESS
REGISTRY
& LOGIC
W#
K
W#
MUX
2a
2a
2a
O
U
T
B
U
F
D
R
I
V
E
R
O
U
T
O
U
T
S
E
L
E
C
T
W R
R E
I G
T
W
R
I
T
E
S
E
N
S
R
E
NWx# or BWx#
D (Data In)
n x a
A
M
P
2
DATA
REGISTRY
& LOGIC
3a
a
a
G
Q
MEMORY
ARRAY
P
F
P
P
2a
U
T
E
R
(Data Out)
2
U
T
U
T
R#
A
S
E 2
E
K
C
K
K#
MUX
CQ, CQ#
C,C#
or
K,K#
(Echo Clock Out)
NOTE:
1. Figure 2 illustrates simplified device operation. See truth table, ball descriptions, and timing diagrams for detailed
information.
2. For 2 Meg x 8, n = 21, a = 8; NWx# = 2 separate nibble writes.
For 1 Meg x 18, n = 20, a = 18; BWx# = 2 separate byte writes.
For 512K x 36, n = 19, a = 36; BWx# = 4 separate byte writes.
18Mb: 1.8V VDD, HSTL, QDRIIb4 SRAM
MT54W1MH18J_H.fm – Rev. H, Pub. 3/03
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2003 Micron Technology, Inc.
4
2 MEG x 8, 1 MEG x 18, 512K x 36
1.8V VDD, HSTL, QDRIIb4 SRAM
Figure 3: Application Example
R = 250Ω
R = 250Ω
SRAM 1
SRAM 2
B
ZQ
Q
ZQ
Q
Vt
CQ
CQ#
K#
CQ
CQ#
K#
B
D
D
SA
R W W
R W W
R
# # #
SA
C
C#
K
#
#
#
C C# K
DATA IN
DATA OUT
Address
Read#
Vt
Vt
R
Write#
BW#
BUS
MASTER
(CPU
or
ASIC)
SRAM 1 Input CQ
SRAM 1 Input CQ#
SRAM 4 Input CQ
SRAM 4 Input CQ#
Source K
Source K#
Delayed K
Delayed K#
R
R = 50Ω
Vt = VREF
NOTE:
1. In this approach, the second clock pair drives the C and C# clocks but is delayed such that return data meets data
setup and hold times at the bus master.
2. Consult Micron Technical Notes for more thorough discussions of clocking schemes.
3. Data capture is possible using only one of the two signals. CQ and CQ# clocks are optional use outputs.
4. For high frequency applications (200 MHz and faster) the CQ and CQ# clocks (for data capture) are recommended
over the C and C# clocks (for data alignment). The C and C# clocks are optional use inputs.
18Mb: 1.8V VDD, HSTL, QDRIIb4 SRAM
MT54W1MH18J_H.fm – Rev. H, Pub. 3/03
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2003 Micron Technology, Inc.
5
2 MEG x 8, 1 MEG x 18, 512K x 36
1.8V VDD, HSTL, QDRIIb4 SRAM
Table 2:
2 Meg x 8 Ball Layout (Top View)
165-Ball FBGA
1
2
3
4
5
6
K#
K
7
8
9
10
11
VSS/SA1
NC
NC/SA3
VSS/SA4
NC
A
B
CQ#
SA
W#
SA
NW1#2
R#
SA
SA
CQ
NC/SA5
SA
NW0#6
SA
NC
NC
NC
NC
NC
Q4
NC
Q5
VDDQ
NC
NC
D6
NC
NC
NC
NC
NC
NC
VDDQ
NC
NC
NC
NC
NC
NC
SA
Q3
D3
NC
Q2
NC
NC
ZQ
D1
NC
Q0
D0
NC
NC
TDI
C
NC
VSS
VSS
NC
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
SA
C
VSS
VSS
NC
D
NC
D4
VSS
VSS
NC
E
NC
NC
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VSS
VSS
VSS
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VSS
D2
F
NC
NC
VDD
VDD
VDD
VDD
VDD
VSS
VDD
VDD
VDD
VDD
VDD
VSS
NC
G
NC
D5
NC
H
DLL#
NC
VREF
NC
VREF
Q1
J
K
NC
NC
NC
L
NC
Q6
NC
M
NC
NC
NC
NC
Q7
SA
VSS
VSS
NC
N
P
NC
D7
VSS
SA
SA
VSS
NC
NC
NC
SA
SA
SA
SA
NC
R
TDO
TCK
SA
SA
C#
SA
SA
TMS
NOTE:
1. Expansion address: 2A for 72Mb
2. NW1# controls writes to D4:D7
3. Expansion address: 7A for 144Mb
4. Expansion address: 10A for 36Mb
5. Expansion address: 5B for 288Mb
6. NW0# controls writes to D0:D3
18Mb: 1.8V VDD, HSTL, QDRIIb4 SRAM
MT54W1MH18J_H.fm – Rev. H, Pub. 3/03
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2003 Micron Technology, Inc.
6
2 MEG x 8, 1 MEG x 18, 512K x 36
1.8V VDD, HSTL, QDRIIb4 SRAM
Table 3:
1 Meg x 18 Ball Layout (Top View)
165-Ball FBGA
1
CQ#
NC
2
VSS/SA1
Q9
3
NC/SA2
D9
4
5
BW1#3
NC
6
7
NC/SA4
BW0#6
SA
8
9
SA
10
VSS/SA5
NC
11
CQ
Q8
D8
D7
Q6
Q5
D5
ZQ
D4
Q3
Q2
D2
D1
Q0
TDI
A
W#
K#
K
R#
B
SA
SA
NC
NC
NC
NC
NC
NC
VDDQ
NC
NC
NC
NC
NC
NC
SA
C
NC
NC
D10
Q10
Q11
D12
Q13
VDDQ
D14
Q14
D15
D16
Q16
Q17
SA
VSS
SA
NC
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
SA
C
VSS
Q7
D
NC
D11
NC
VSS
VSS
VSS
VSS
NC
E
NC
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VSS
VSS
VSS
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VSS
D6
F
NC
Q12
D13
VREF
NC
VDD
VDD
VDD
VDD
VDD
VSS
VDD
VDD
VDD
VDD
VDD
VSS
NC
G
NC
NC
H
DLL#
NC
VREF
Q4
J
K
NC
NC
D3
L
NC
Q15
NC
NC
M
NC
VSS
VSS
Q1
N
P
NC
D17
NC
VSS
SA
SA
VSS
NC
NC
SA
SA
SA
SA
D0
R
TDO
TCK
SA
SA
C#
SA
SA
TMS
NOTE:
1. Expansion address: 2A for 144Mb
2. Expansion address: 3A for 36Mb
3. BW1# controls writes to D9:D17
4. Expansion address: 7A for 288Mb
5. Expansion address: 10A for 72Mb
6. BW0# controls writes to D0:D8
18Mb: 1.8V VDD, HSTL, QDRIIb4 SRAM
MT54W1MH18J_H.fm – Rev. H, Pub. 3/03
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2003 Micron Technology, Inc.
7
2 MEG x 8, 1 MEG x 18, 512K x 36
1.8V VDD, HSTL, QDRIIb4 SRAM
Table 4:
512K x 36 Ball Layout (Top View)
165-Ball FBGA
1
2
VSS/SA1
Q18
Q28
D20
D29
Q21
D22
VREF
Q31
D32
Q24
Q34
D26
D35
TCK
3
NC/SA2
D18
D19
Q19
Q20
D21
Q22
VDDQ
D23
Q23
D24
D25
Q25
Q26
SA
4
5
BW2#3
BW3#7
SA
6
7
BW1#4
BW0#8
SA
8
9
NC/SA5
D17
D16
Q16
Q15
D14
Q13
VDDQ
D12
Q12
D11
D10
Q10
Q9
10
VSS/SA6
Q17
Q7
11
CQ
Q8
D8
D7
Q6
Q5
D5
ZQ
D4
Q3
Q2
D2
D1
Q0
TDI
A
CQ#
Q27
D27
D28
Q29
Q30
D30
DLL#
D31
Q32
Q33
D33
D34
Q35
TDO
W#
K#
K
R#
B
SA
SA
C
VSS
NC
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
SA
C
VSS
D
VSS
VSS
VSS
VSS
D15
D6
E
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VSS
VSS
VSS
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VSS
F
VDD
VDD
VDD
VDD
VDD
VSS
VDD
VDD
VDD
VDD
VDD
VSS
Q14
D13
VREF
Q4
G
H
J
K
D3
L
Q11
Q1
M
VSS
VSS
N
P
VSS
SA
SA
VSS
D9
SA
SA
SA
SA
D0
R
SA
SA
C#
SA
SA
SA
TMS
NOTE:
1. Expansion address: 2A for 288Mb
2. Expansion address: 3A for 72Mb
3. BW2# controls writes to D18:D26
4. BW1# controls writes to D9:D17
5. Expansion address: 9A for 36Mb
6. Expansion address: 10A for 144Mb
7. BW3# controls writes to D27:D35
8. BW0# controls writes to D0:D8
18Mb: 1.8V VDD, HSTL, QDRIIb4 SRAM
MT54W1MH18J_H.fm – Rev. H, Pub. 3/03
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2003 Micron Technology, Inc.
8
2 MEG x 8, 1 MEG x 18, 512K x 36
1.8V VDD, HSTL, QDRIIb4 SRAM
Table 5:
Ball Descriptions
SYMBOL
TYPE
DESCRIPTION
BW_#
NW_#
Input
Synchronous Byte Writes (or Nibble Writes on x8): When LOW, these inputs cause their
respective bytes to be registered and written if W# had initiated a WRITE cycle. These signals
must meet setup and hold times around the rising edges of K and K# for each of the four
rising edges comprising the WRITE cycle. See Ball Layout figures for signal to data
relationships.
C
C#
Input
Output Clock: This clock pair provides a user-controlled means of tuning device output data.
The rising edge of C# is used as the output timing reference for first output data. The rising
edge of C is used as the output reference for second output data. Ideally, C# is 180 degrees
out of phase with C. C and C# may be tied HIGH to force the use of K and K# as the output
reference clocks instead of having to provide C and C# clocks. If tied HIGH, these inputs may
not be allowed to toggle during device operation.
D_
Input
Synchronous Data Inputs: Input data must meet setup and hold times around the rising edges
of K and K# during WRITE operations. See Ball Layout figures for ball site location of
individual signals. The x8 device uses D0:D7. Remaining signals are NC. The x18 device uses
D0:D17. Remaining signals are NC. The x36 device uses D0:D35. Remaining signals are NC.
DLL#
Input
Input
DLL Disable: When LOW, this input causes the DLL to be bypassed for stable, low-frequency
operation.
K
K#
Input Clock: This input clock pair registers address and control inputs on the rising edge of K,
and registers data on the rising edge of K and the rising edge of K#. K# is ideally 180 degrees
out of phase with K. All synchronous inputs must meet setup and hold times around the clock
rising edges.
R#
SA
Input
Input
Synchronous Read: When LOW, this input causes the address inputs to be registered and a
READ cycle to be initiated. This input must meet setup and hold times around the rising edge
of K and is ignored on the subsequent rising edge of K.
Synchronous Address Inputs: These inputs are registered and must meet the setup and hold
times around the rising edge of K for READ cycles and must meet the setup and hold times
around the rising edge of K# for WRITE cycles. See Ball Layout figures for address expansion
inputs. All transactions operate on a burst of four words (two clock periods of bus activity).
These inputs are ignored when both ports are deselected.
TCK
Input
Input
Input
Input
IEEE 1149.1 Clock Input: 1.8V I/O levels. This ball must be tied to VSS if the JTAG function is not
used in the circuit.
TMS
TDI
IEEE 1149.1 Test Inputs: 1.8V I/O levels. These balls may be left as No Connects if the JTAG
function is not used in the circuit.
VREF
HSTL Input Reference Voltage: Nominally VDDQ/2, but may be adjusted to improve system
noise margin. Provides a reference voltage for the HSTL input buffer trip point.
W#
Synchronous Write: When LOW, this input causes the address inputs to be registered and a
WRITE cycle to be initiated. This input must meet setup and hold times around the rising
edge of K.
ZQ
Input
Output Impedance Matching Input: This input is used to tune the device outputs to the
system data bus impedance. DQ output impedance is set to 0.2 x RQ, where RQ is a resistor
from this ball to ground. Alternately, this ball can be connected directly to VDDQ to enable
the minimum impedance mode. This ball cannot be connected directly to GND or left
unconnected.
CQ#, CQ
Q_
Output
Output
Synchronous Echo Clock Outputs: The edges of these outputs are tightly matched to the
synchronous data outputs and can be used as data valid indication. These signals run freely
and do not stop when Q tri-states.
Synchronous Data Outputs: Output data is synchronized to the respective C and C# or to K
and K# rising edges if C and C# are tied HIGH. This bus operates in response to R# commands.
See Ball Layout figures for ball site location of individual signals. The x8 device uses Q0:Q7.
Remaining signals are NC. The x18 device uses Q0:Q17. Remaining signals are NC. The x36
device uses Q0:Q35. Remaining signals are NC.
18Mb: 1.8V VDD, HSTL, QDRIIb4 SRAM
MT54W1MH18J_H.fm – Rev. H, Pub. 3/03
Micron Technology, Inc., reserves the right to change products or specifications without notice.
9
©2003 Micron Technology, Inc.
2 MEG x 8, 1 MEG x 18, 512K x 36
1.8V VDD, HSTL, QDRIIb4 SRAM
Table 5:
Ball Descriptions (continued)
SYMBOL
TYPE
DESCRIPTION
TDO
VDD
Output
Supply
IEEE 1149.1 Test Output: 1.8V I/0 level.
Power Supply: 1.8V nominal. See DC Electrical Characteristics and Operating Conditions for
range.
VDDQ
Supply
Power Supply: Isolated Output Buffer Supply. Nominally, 1.5V. 1.8V is also permissible. See DC
Electrical Characteristics and Operating Conditions for range.
VSS
NC
Supply
–
Power Supply: GND.
No Connect: These balls are internally connected to the die, but have no function and may be
left not connected to the board to minimize ball count.
18Mb: 1.8V VDD, HSTL, QDRIIb4 SRAM
MT54W1MH18J_H.fm – Rev. H, Pub. 3/03
Micron Technology, Inc., reserves the right to change products or specifications without notice.
10
©2003 Micron Technology, Inc.
2 MEG x 8, 1 MEG x 18, 512K x 36
1.8V VDD, HSTL, QDRIIb4 SRAM
Figure 4:
Bus Cycle State Diagram
RD
RD & R_Count=4
always
LOAD NEW
READ ADDRESS;
R_Count=0;
R_Init=1
always
INCREMENT READ
ADDRESS BY TWO
R_Init=0
READ DOUBLE;
R_Count=R_Count+2
READ PORT NOP
R_Init=0
/RD
1
R_Count=2
Supply
voltage
/RD & R_Count=4
provided
POWER-UP
WT & R_Init=0
Supply
voltage
provided
WT & W_Count=4
always
LOAD NEW
WRITE ADDRESS;
W_Count=0
always
INCREMENT WRITE
ADDRESS BY TWO
WRITE DOUBLE;
W_Count=W_Count+2
/WT
1
WRITE PORT NOP
W_Count=2
/WT & W_Count=4
NOTE:
1. The address is concatenated with two additional internal LSBs to facilitate BURST operation. The address order is
always fixed as: xxx...xxx+0, +1, +2, +3. Bus cycle is terminated at the end of this sequence (burst count = 4).
2. State transitions: RD = (R# = LOW); WT = (W# = LOW).
3. Read and write state machines can be simultaneously active.
4. State machine, control timing sequence is controlled by K.
18Mb: 1.8V VDD, HSTL, QDRIIb4 SRAM
MT54W1MH18J_H.fm – Rev. H, Pub. 3/03
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2003 Micron Technology, Inc.
11
2 MEG x 8, 1 MEG x 18, 512K x 36
1.8V VDD, HSTL, QDRIIb4 SRAM
Table 6:
Notes 1–8
Truth Table
OPERATION
K
R#
W#
D or Q
D or Q
D or Q
D or Q
LJH
X
L
DA(A0)
at
K(t)I
DA(A0 + 1)
at
K#(t + 1)I
DA(A0 + 2)
at
K(t + 2)I
DA(A0 + 3)
at
K#(t + 3)I
WRITE Cycle:
Load address, input write data on
two consecutive K and K# rising
edges
LJH
L
X
QA(A0)
at
C#(t)I
QA(A0 + 1)
at
C(t + 1)I
QA(A + 2)
at
C#(t + 2)I
QA(A0 + 3)
at
C(t + 3)I
READ Cycle:
Load address, output data on two
consecutive C and C# rising edges
LJH
H
X
H
X
D = X
Q = High-Z
D = X
Q = High-Z
D = X
Q = High-Z
D = X
Q = High-Z
NOP: No operation
Stopped
Previous
State
Previous
State
Previous
State
Previous
State
STANDBY: Clock stopped
Table 7:
Notes 9, 10
BYTE WRITE Operation
OPERATION
K
K#
BW0#
BW1#
LJH
LJH
LJH
LJH
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
WRITE D0:17 at K rising edge
WRITE D0:17 at K# rising edge
WRITE D0:8 at K rising edge
WRITE D0:8 at K# rising edge
WRITE D9:17 at K rising edge
WRITE D9:17 at K# rising edge
WRITE nothing at K rising edge
WRITE nothing at K# rising edge
LJH
LJH
LJH
LJH
NOTE:
1. X means “Don’t Care.” H means logic HIGH. L means logic LOW. Iꢀmeans rising edge; Kꢀmeans falling edge.
2. Data inputs are registered at K and K# rising edges. Data outputs are delivered at C and C# rising edges, except if C
and C# are HIGH, then data outputs are delivered at K and K# rising edges.
3. R# and W# must meet setup and hold times around the rising edge (LOW to HIGH) of K and are registered at the ris-
ing edge of K.
4. This device contains circuitry that will ensure the outputs will be in High-Z during power-up.
5. Refer to state diagram and timing diagrams for clarification.
6. It is recommended that K = K# = C = C# when clock is stopped. This is not essential, but permits most rapid restart by
overcoming transmission line charging symmetrically.
7. If this signal was LOW to initiate the previous cycle, this signal becomes a “Don’t Care” for this operation; however,
it is strongly recommended that this signal is brought HIGH, as shown in the truth table.
8. This signal was HIGH on previous K clock rising edge. Initiating consecutive READ or WRITE operations on consecu-
tive K clock rising edges is not permitted. The device will ignore the second request.
9. Assumes a WRITE cycle was initiated. BW0# and BW1# can be altered for any portion of the BURST WRITE operation,
provided that the setup and hold requirements are satisfied.
10.This table illustrates operation for x18 devices. The x36 device operation is similar except for the addition of BW2#
(controls D18:D26) and BW3# (controls D27:D35). The x8 device operation is similar except that NW0# controls D0:D3
and NW1# controls D4:D7.
18Mb: 1.8V VDD, HSTL, QDRIIb4 SRAM
MT54W1MH18J_H.fm – Rev. H, Pub. 3/03
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2003 Micron Technology, Inc.
12
2 MEG x 8, 1 MEG x 18, 512K x 36
1.8V VDD, HSTL, QDRIIb4 SRAM
Stresses greater than those listed under Absolute
Maximum Ratings may cause permanent damage to
the device. This is a stress rating only, and functional
operation of the device at these or any other condi-
tions above those indicated in the operational sections
of this specification is not implied. Exposure to abso-
lute maximum rating conditions for extended periods
may affect reliability.
Absolute Maximum Ratings
Voltage on VDD Supply Relative to VSS.....-0.5V to +2.8V
Voltage on VDDQ Supply
Relative to VSS ....................................... -0.5V to +VDD
VIN ..................................................... -0.5V to VDD + 0.5V
Storage Temperature..............................-55ºC to +125ºC
Junction Temperature .......................................... +125ºC
Short Circuit Output Current .............................. 70mA
Maximum Junction Temperature depends upon
package type, cycle time, loading, ambient tempera-
ture, and airflow.
Table 8:
DC Electrical Characteristics and Operating Conditions
Notes appear following parameter tables on page 17; 0°C ? TA ? +70°C; VDD = 1.8V 0.1V unless otherwise noted
DESCRIPTION
CONDITIONS
SYMBOL
VIH(DC)
VIL(DC)
VIN
MIN
VREF + 0.1
-0.3
MAX
VDDQ + 0.3
VREF - 0.1
VDDQ + 0.3
5
UNITS NOTES
Input High (Logic 1) Voltage
Input Low (Logic 0) Voltage
Clock Input Signal Voltage
Input Leakage Current
Output Leakage Current
V
V
3, 4
3, 4
3, 4
-0.3
V
0V ? VIN ? VDDQ
ILI
-5
µA
µA
Output(s) disabled,
ILO
-5
5
0V ? VIN ? VDDQ (Q)
Output High Voltage
Output Low Voltage
|IOH| ? 0.1mA
Note 1
VOH (LOW)
VOH
VDDQ - 0.2
VDDQ
V
V
V
V
V
V
V
3, 5, 6
3, 5, 6
3, 5, 6
3, 5, 6
3
VDDQ/2 - 0.12 VDDQ/2 + 0.12
VSS 0.2
VDDQ/2 - 0.12 VDDQ/2 + 0.12
IOL ? 0.1mA
Note 2
VOL (LOW)
VOL
VDD
1.7
1.4
1.9
VDD
0.95
Supply Voltage
VDDQ
VREF
3, 7
Isolated Output Buffer Supply
Reference Voltage
0.68
3
Table 9:
AC Electrical Characteristics and Operating Conditions
Notes appear following parameter tables on page 17; 0°C ? TA ? +70°C; VDD = 1.8V 0.1V unless otherwise noted
DESCRIPTION
CONDITIONS
SYMBOL
VIH(AC)
MIN
VREF + 0.2
-
MAX
-
UNITS NOTES
V
V
3, 4, 8
3, 4, 8
Input High (Logic 1) Voltage
Input Low (Logic 1) Voltage
VIL(AC)
VREF - 0.2
18Mb: 1.8V VDD, HSTL, QDRIIb4 SRAM
MT54W1MH18J_H.fm – Rev. H, Pub. 3/03
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2003 Micron Technology, Inc.
13
2 MEG x 8, 1 MEG x 18, 512K x 36
1.8V VDD, HSTL, QDRIIb4 SRAM
.
Table 10: IDD Operating Conditions and Maximum Limits
Notes appear following parameter tables on page 17; 0°C ? TA ? +70°C; VDD = 1.8V 0.1V unless otherwise noted
MAX
DESCRIPTION
CONDITIONS
SYM
TYP
-3
-3.3
-4
-5
-6
-7.5 UNITS NOTES
Operating
Supply
Current: DDR
All inputs ? VIL or O VIH; Cycle
t
time Oꢀ KHKH (MIN); Outputs
TBD
mA
9, 10
open; 100% bus utilization;
50% address and data bits
toggling on each clock cycle
IDD
x8, x18
x36
525
710
475
640
400
545
330
445
280
380
235
310
tKHKH = tKHKH (MIN);
Device in NOP state;
All addresses/data static
ISB1
x8, x18
x36
Standby
Supply
Current: NOP
TBD
TBD
mA
mA
10, 11
12
255
265
235
245
200
210
170
180
145
155
125
135
Output Supply
Current: DDR
(Information
only)
IDDQ
x8
x18
x36
CL = 15pF
42
95
189
38
85
170
32
71
142
32
71
142
25
57
113
21
47
95
Table 11: Capacitance
Note 13; notes appear following parameter tables on page 17
DESCRIPTION
CONDITIONS
SYMBOL
TYP
MAX
UNITS
CI
4.5
6
5.5
7
pF
pF
pF
Address/Control Input Capacitance
Output Capacitance (Q)
Clock Capacitance
TA = 25ºC; f = 1 MHz
CO
CCK
5.5
6.5
Table 12: Thermal Resistance
Note 13; notes appear following parameter tables on page 17
DESCRIPTION
CONDITIONS
SYMBOL
TYP
UNITS
NOTES
ꢁJA
19.4
ºC/W
14
Junction to Ambient
(Airflow of 1m/s)
Soldered on a 4.25 x 1.125 inch,
4-layer printed circuit board
ꢁJC
ꢁJB
1.0
9.6
ºC/W
ºC/W
Junction to Case (Top)
15
Junction to Balls (Bottom)
18Mb: 1.8V VDD, HSTL, QDRIIb4 SRAM
MT54W1MH18J_H.fm – Rev. H, Pub. 3/03
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2003 Micron Technology, Inc.
14
2 MEG x 8, 1 MEG x 18, 512K x 36
1.8V VDD, HSTL, QDRIIb4 SRAM
Table 13: AC Electrical Characteristics And Recommended Operating Conditions
Notes 16–19, 22, notes appear following paramater tables on page 17; 0°C ? TA ? +70°C; TJ ? +95°C; VDD = 1.8V 0.1V
-3
-3.3
-4
-5
-6
-7.5
DESCRIPTION
Clock
SYM
UNITS NOTES
MIN MAX MIN MAX MIN MAX MIN MAX MIN MAX MIN MAX
Clock cycle
time
(K, K#, C, C#)
tKHKH
tKC var
tKHKL
tKLKH
3.00 3.47 3.30 4.20 4.00 5.25 5.00 6.30 6.00 7.88 7.50 8.40
ns
ns
ns
ns
20
21
Clock Phase
Jitter (K, K#,
C, C#)
0.20
0.20
0.20
0.20
0.20
0.20
Clock HIGH
time
(K, K#, C, C#)
1.20
1.20
1.32
1.32
1.60
1.60
2.00
2.00
2.40
2.40
3.00
3.00
Clock LOW
time
(K, K#, C, C#)
Clock to
clock#
(KIJK#I,
CIJC#I) at
tKHKH
tKHK#H
tK#HKH
1.35
1.35
1.49
1.49
1.80
1.80
2.20
2.20
2.70
2.70
3.38
3.38
ns
minimum
Clock# to
clock
(K#IJKI,
C#IJCI) at
tKHKH
ns
ns
minimum
Clock to data
clock (KIJCI,
K#IJC#I)
tKHCH
0.00 1.30 0.00 1.45 0.00 1.80 0.00 2.30 0.00 2.80 0.00 3.55
DLL lock time
(K, C)
tKC lock
1,024
30
1,024
30
1,024
30
1,024
30
1,024
30
1,024
30
cycles
ns
22
tKC
reset
K static to
DLL reset
Output Times
C, C# HIGH to
output valid
tCHQV
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.45
0.50
0.50
0.50
0.50
ns
ns
C, C# HIGH to
output hold
tCHQX -0.45
tCHCQV
-0.45
-0.45
-0.45
-0.45
-0.45
-0.45
-0.50
-0.50
-0.50
-0.50
C, C# HIGH to
echo clock
valid
ns
ns
ns
C, C# HIGH to
echo clock
hold
tCHCQX -0.45
tCQHQV
CQ, CQ# HIGH
to output
valid
0.25
0.27
0.30
0.35
0.40
0.40
23
18Mb: 1.8V VDD, HSTL, QDRIIb4 SRAM
MT54W1MH18J_H.fm – Rev. H, Pub. 3/03
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2003 Micron Technology, Inc.
15
2 MEG x 8, 1 MEG x 18, 512K x 36
1.8V VDD, HSTL, QDRIIb4 SRAM
Table 13: AC Electrical Characteristics And Recommended Operating Conditions
(continued)
-3
-3.3
-4
-5
-6
-7.5
DESCRIPTION
SYM
UNITS NOTES
MIN MAX MIN MAX MIN MAX MIN MAX MIN MAX MIN MAX
CQ, CQ# HIGH
to output
hold
tCQHQX -0.25
tCHQZ
-0.27
-0.45
-0.30
-0.45
-0.35
-0.45
-0.40
-0.50
-0.40
-0.50
ns
23
C HIGH to
output High-
Z
0.45
0.45
0.45
0.45
0.50
0.50
ns
ns
C HIGH to
output Low-Z
tCHQX1
-0.45
Setup Times
Address valid
to K rising
edge
tAVKH
tIVKH
0.40
0.40
0.28
0.40
0.40
0.30
0.50
0.50
0.35
0.60
0.60
0.40
0.70
0.70
0.50
0.70
0.70
0.50
ns
ns
ns
16
Control
inputs valid
to K rising
edge
16
16
Data-in valid
to K, K# rising
edge
tDVKH
Hold Times
K rising edge
to address
hold
tKHAX
tKHIX
0.40
0.40
0.28
0.40
0.40
0.30
0.50
0.50
0.35
0.60
0.60
0.40
0.70
0.70
0.50
0.80
0.80
0.50
ns
ns
ns
16
K rising edge
to control
inputs hold
16
17
K, K# rising
edge to data-
in hold
tKHDX
18Mb: 1.8V VDD, HSTL, QDRIIb4 SRAM
MT54W1MH18J_H.fm – Rev. H, Pub. 3/03
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2003 Micron Technology, Inc.
16
2 MEG x 8, 1 MEG x 18, 512K x 36
1.8V VDD, HSTL, QDRIIb4 SRAM
Notes
1. Outputs are impedance-controlled. |IOH|
=
12. Average I/O current and power is provided for
informational purposes only and is not tested.
Calculation assumes that all outputs are loaded
with CL (in farads), f = input clock frequency, half
of outputs toggle at each transition (n = 18 for the
x36), CO = 6pF, VDDQ = 1.5V and uses the equa-
tions: Average I/O Power as dissipated by the
SRAM is: P = 0.5 × n × f × VDDQ2 x (CL + 2CO).
Average IDDQ = n × f × VDDQ x (CL + CO).
13. This parameter is sampled.
14. Average thermal resistance between the die and
the case top surface per MIL SPEC 883 Method
1012.1.
15. Junction temperature is a function of total device
power dissipation and device mounting environ-
ment. Measured per SEMI G38-87.8.
16. This is a synchronous device. All addresses, data,
and control lines must meet the specified setup
and hold times for all latching clock edges.
17. Test conditions as specified with the output load-
ing as shown in Figure 5 unless otherwise noted.
18. Control input signals may not be operated with
(VDDQ/2)/(RQ/5) for values of 175ꢀ ? RQ ? 350ꢀꢁ.
2. Outputs are impedance-controlled. IOL = (VDDQ/
2)/(RQ/5) for values of 175ꢀ ? RQ ? 350ꢀꢁ.
3. All voltages referenced to Vss (GND).
t
4. Overshoot: VIH(AC) ? VDD + 0.7V for t ? KHKH/2
t
Undershoot:VIL(AC) O -0.5V for t ? KHKH/2
Power-up: VIH ? VDDQ + 0.3V and VDD ? 1.7V
and VDDQ ? 1.4V for t ? 200ms
During normal operation, VDDQ must not exceed
VDD. R# and W# signals may not have pulse
t
widths less than KHKL (MIN) or operate at cycle
rates less than tKHKH (MIN).
5. AC load current is higher than the shown DC val-
ues. AC I/O curves are available upon request.
6. HSTL outputs meet JEDEC HSTL Class I and Class
II standards.
7. The nominal value of VDDQ may be set within the
range of 1.5V to 1.8V DC, and the variation of
VDDQ must be limited to 0.1V DC.
8. To maintain a valid level, the transitioning edge of
the input must:
pulse widths less than tKHKL (MIN).
a. Sustain a constant slew rate from the current AC
level through the target AC level, VIL(AC) or
VIH(AC).
b. Reach at least the target AC level.
c. After the AC target level is reached, continue to
maintain at least the target DC level, VIL(DC) or
VIH(DC).
19. If C and C# are tied HIGH, then K and K# become
the references for C and C# timing parameters.
20. The device will operate at clock frequencies
t
slower than KHKH (MAX). See Micron Technical
Note TN-54-02 for more information.
21. Clock phase jitter is the variance from clock rising
edge to the next expected clock rising edge.
22. VDD slew rate must be less than 0.1V DC per 50ns
for DLL lock retention. DLL lock time begins once
VDD and input clock are stable.
23. Echo clock is tightly controlled to data valid/data
hold. By design, there is a 0.1ns variation from
echo clock to data. The data sheet parameters
reflect tester guardbands and test setup varia-
tions.
9. IDD is specified with no output current. IDD is lin-
ear with frequency. Typical value is measured at
6ns cycle time.
10. Typical values are measured at VDD = 1.8V, VDDQ =
1.5V, and temperature = 25°C.
11. NOP currents are valid when entering NOP after
all pending READ and WRITE cycles are com-
pleted.
18Mb: 1.8V VDD, HSTL, QDRIIb4 SRAM
MT54W1MH18J_H.fm – Rev. H, Pub. 3/03
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2003 Micron Technology, Inc.
17
2 MEG x 8, 1 MEG x 18, 512K x 36
1.8V VDD, HSTL, QDRIIb4 SRAM
AC Test Conditions
Figure 5:
Output Load Equivalent
Input pulse levels ................................ 0.25V to 1.25V
Input rise and fall times...................................... 0.7ns
Input timing reference levels .............................0.75V
Output reference levels...................................VDDQ/2
ZQ for 50ꢀ impedance...........................................250ꢀ
Output load ..............................................See Figure 5
0.75V
VDDQ/2
VREF
50Ω
ZO= 50Ω
SRAM
250Ω
ZQ
18Mb: 1.8V VDD, HSTL, QDRIIb4 SRAM
MT54W1MH18J_H.fm – Rev. H, Pub. 3/03
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2003 Micron Technology, Inc.
18
2 MEG x 8, 1 MEG x 18, 512K x 36
1.8V VDD, HSTL, QDRIIb4 SRAM
Figure 6:
READ/WRITE Timing
NOP
1
READ
2
WRITE
3
READ
4
WRITE
5
NOP
6
7
K
t
t
t
t
KHKL KLKH
KHKH
KHK#H
K#
R#
t
t
t
t
IVKH
KHIX
IVKH KHIX
W#
A
(Note 3)
A0
A1
A2
A3
t
t
KHDX
KHDX
t
t
AVKH KHAX
t
t
DVKH
DVKH
D
Q
D30
D31
Q21
D32
D33
Q23
D10
(Note 1)
Q00
D11
D12
D13
Qx2
Qx3
Q01
t
Q02
Q03
Q20
Q22
t
t
CHQV
CHQX
CHQZ
t
KHCH
t
t
CQHQV
CHQX1
t
t
CQHQX
CHQX
t
CHQV
C
t
t
t
t
KHCH
KHKH
KHKL KLKH
t
KHK#H
C#
t
CHCQV
CHCQX
t
CQ
t
t
CHCQV
CHCQX
CQ#
NOTE:
1. Q00 refers to output from address A0 + 1. Q01 refers to output from the next internal burst address following
A0, i.e., A0 + 1.
2. Outputs are disabled (High-Z) one clock cycle after a NOP.
3. In this example, if address A2 ꢂ A1, then data Q20 = D10 and Q21 = D11. Write data is forwarded immediately as
read results. (This note applies to whole diagram.)
18Mb: 1.8V VDD, HSTL, QDRIIb4 SRAM
MT54W1MH18J_H.fm – Rev. H, Pub. 3/03
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2003 Micron Technology, Inc.
19
2 MEG x 8, 1 MEG x 18, 512K x 36
1.8V VDD, HSTL, QDRIIb4 SRAM
IEEE 1149.1 Serial Boundary Scan
(JTAG)
Figure 7:
TAP Controller State Diagram
The SRAM incorporates a serial boundary scan test
access port (TAP). This port operates in accordance
with IEEE Standard 1149.1-1990 but does not have the
set of functions required for full 1149.1 compliance.
These functions from the IEEE specification are
excluded because their inclusion places an added
delay in the critical speed path of the SRAM. Note that
the TAP controller functions in a manner that does not
conflict with the operation of other devices using
1149.1 fully-compliant TAPs. The TAP operates using
JEDEC-standard 1.8V I/O logic levels.
TEST-LOGIC
1
RESET
0
1
1
1
RUN-TEST/
IDLE
SELECT
DR-SCAN
SELECT
IR-SCAN
0
0
0
1
1
CAPTURE-DR
CAPTURE-IR
0
0
SHIFT-DR
0
SHIFT-IR
0
1
1
1
1
EXIT1-DR
EXIT1-IR
The SRAM contains a TAP controller, instruction
register, boundary scan register, bypass register, and
ID register.
0
0
PAUSE-DR
1
0
PAUSE-IR
1
0
0
0
EXIT2-DR
1
EXIT2-IR
1
Disabling the JTAG Feature
It is possible to operate the SRAM without using the
JTAG feature. To disable the TAP controller, TCK must
be tied LOW (VSS) to prevent clocking of the device.
TDI and TMS are internally pulled up and may be
unconnected. Alternately, they may be connected to
VDD through a pull-up resistor. TDO should be left
unconnected. Upon power-up, the device will come up
in a reset state which will not interfere with the opera-
tion of the device.
UPDATE-DR
UPDATE-IR
1
0
1
0
NOTE:
The 0/1 next to each state represents the value
of TMS at the rising edge of TCK.
Test MODE SELECT (TMS)
The TMS input is used to give commands to the TAP
controller and is sampled on the rising edge of TCK. It
is allowable to leave this ball unconnected if the TAP is
not used. The ball is pulled up internally, resulting in a
logic HIGH level.
Test Access Port (TAP)
Test Clock (TCK)
The test clock is used only with the TAP controller.
All inputs are captured on the rising edge of TCK. All
outputs are driven from the falling edge of TCK.
Test Data-In (TDI)
The TDI ball is used to serially input information
into the registers and can be connected to the input of
any of the registers. The register between TDI and TDO
is chosen by the instruction that is loaded into the TAP
instruction register. For information on loading the
instruction register, see Figure 7. TDI is pulled up
internally and can be unconnected if the TAP is
unused in an application. TDI is connected to the most
significant bit (MSB) of any register, as illustrated in
Figure 8.
18Mb: 1.8V VDD, HSTL, QDRIIb4 SRAM
MT54W1MH18J_H.fm – Rev. H, Pub. 3/03
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2003 Micron Technology, Inc.
20
2 MEG x 8, 1 MEG x 18, 512K x 36
1.8V VDD, HSTL, QDRIIb4 SRAM
Test Data-Out (TDO)
Figure 8:
TAP Controller Block Diagram
The TDO output ball is used to serially clock data-
out from the registers. The output is active depending
upon the current state of the TAP state machine, as
illustrated in Figure 7. The output changes on the fall-
ing edge of TCK. TDO is connected to the least signifi-
cant bit (LSB) of any register, as depicted in Figure 8.
0
Bypass Register
2
1 0
Selection
Circuitry
Selection
Circuitry
Instruction Register
31 30 29
Identification Register
TDI
TDO
.
.
. 2 1 0
Performing a TAP RESET
A reset is performed by forcing TMS HIGH (VDD) for
five rising edges of TCK. This RESET does not affect the
operation of the SRAM and may be performed while
the SRAM is operating.
x
.
.
.
.
. 2 1 0
Boundary Scan Register
TCK
TMS
At power-up, the TAP is reset internally to ensure
that TDO comes up in a High-Z state.
TAP CONTROLLER
TAP Registers
NOTE:
Registers are connected between the TDI and TDO
balls and allow data to be scanned into and out of the
SRAM test circuitry. Only one register can be selected
at a time through the instruction register. Data is seri-
ally loaded into the TDI ball on the rising edge of TCK.
Data is output on the TDO ball on the falling edge of
TCK.
X = 106.
Boundary Scan Register
The boundary scan register is connected to all the
input and bidirectional balls on the SRAM. The SRAM
has a 107-bit-long register.
The boundary scan register is loaded with the con-
tents of the RAM I/O ring when the TAP controller is in
the Capture-DR state and is then placed between the
TDI and TDO balls when the controller is moved to the
Shift-DR state. The EXTEST, SAMPLE/PRELOAD, and
SAMPLE Z instructions can be used to capture the
contents of the I/O ring.
The Boundary Scan Order tables show the order in
which the bits are connected. Each bit corresponds to
one of the balls on the SRAM package. The MSB of the
register is connected to TDI, and the LSB is connected
to TDO.
Instruction Register
Three-bit instructions can be serially loaded into
the instruction register. This register is loaded when it
is placed between the TDI and TDO balls, as shown in
Figure 8. Upon power-up, the instruction register is
loaded with the IDCODE instruction. It is also loaded
with the IDCODE instruction if the controller is placed
in a reset state, as described in the previous section.
When the TAP controller is in the Capture-IR state,
the two LSBs are loaded with a binary “01” pattern to
allow for fault isolation of the board-level serial test
data path.
Identification (ID) Register
The ID register is loaded with a vendor-specific, 32-
bit code during the Capture-DR state when the
IDCODE command is loaded in the instruction regis-
ter. The IDCODE is hardwired into the SRAM and can
be shifted out when the TAP controller is in the Shift-
DR state. The ID register has a vendor code and other
information described in the Identification Register
Definitions table.
Bypass Register
To save time when serially shifting data through reg-
isters, it is sometimes advantageous to skip certain
chips. The bypass register is a single-bit register that
can be placed between the TDI and TDO balls. This
allows data to be shifted through the SRAM with mini-
mal delay. The bypass register is set LOW (Vss) when
the BYPASS instruction is executed.
18Mb: 1.8V VDD, HSTL, QDRIIb4 SRAM
MT54W1MH18J_H.fm – Rev. H, Pub. 3/03
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2003 Micron Technology, Inc.
21
2 MEG x 8, 1 MEG x 18, 512K x 36
1.8V VDD, HSTL, QDRIIb4 SRAM
and TDO balls and allows the IDCODE to be shifted
out of the device when the TAP controller enters the
Shift-DR state. The IDCODE instruction is loaded into
the instruction register upon power-up or whenever
the TAP controller is given a test logic reset state.
TAP Instruction Set
Overview
Eight different instructions are possible with the
three-bit instruction register. All combinations are
listed in the Instruction Codes table. Three of these
instructions are listed as RESERVED and should not be
used. The other five instructions are described in detail
below.
SAMPLE Z
The SAMPLE Z instruction causes the boundary
scan register to be connected between the TDI and
TDO balls when the TAP controller is in a Shift-DR
state. It also places all SRAM outputs into a High-Z
state.
The TAP controller used in this SRAM is not fully
compliant to the 1149.1 convention because some of
the mandatory 1149.1 instructions are not fully imple-
mented. The TAP controller cannot be used to load
address, data or control signals into the SRAM and
cannot preload the I/O buffers. The SRAM does not
implement the 1149.1 commands EXTEST or INTEST
or the PRELOAD portion of SAMPLE/PRELOAD;
rather, it performs a capture of the I/O ring when these
instructions are executed.
SAMPLE/PRELOAD
SAMPLE/PRELOAD is a 1149.1 mandatory instruc-
tion. The PRELOAD portion of this instruction is not
implemented, so the device TAP controller is not fully
1149.1-compliant.
Note that since the PRELOAD part of the command
is not implemented, putting the TAP into the Update-
DR state while performing a SAMPLE/PRELOAD
instruction will have the same effect as the Pause-DR
command.
EXTEST
EXTEST is a mandatory 1149.1 instruction which is
to be executed whenever the instruction register is
loaded with all 0s. EXTEST is not implemented in this
SRAM TAP controller; therefore, this device is not
1149.1-compliant.
BYPASS
The TAP controller does recognize an all-0 instruc-
tion. When an EXTEST instruction is loaded into the
instruction register, the SRAM responds as if a
SAMPLE/PRELOAD instruction has been loaded.
EXTEST does not place the SRAM outputs (including
CQ and CQ#) in a High-Z state.
When the BYPASS instruction is loaded in the
instruction register and the TAP is placed in a Shift-DR
state, the bypass register is placed between the TDI
and TDO balls. The advantage of the BYPASS instruc-
tion is that it shortens the boundary scan path when
multiple devices are connected together on a board.
IDCODE
Reserved
The IDCODE instruction causes a vendor-specific,
32-bit code to be loaded into the instruction register. It
also places the instruction register between the TDI
These instructions are not implemented but are
reserved for future use. Do not use these instructions.
18Mb: 1.8V VDD, HSTL, QDRIIb4 SRAM
MT54W1MH18J_H.fm – Rev. H, Pub. 3/03
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2003 Micron Technology, Inc.
22
2 MEG x 8, 1 MEG x 18, 512K x 36
1.8V VDD, HSTL, QDRIIb4 SRAM
Figure 9: TAP Timing
1
2
3
4
5
6
Test Clock
(TCK)
t
t
t
t
THTH
THTL
TLTH
t
t
MVTH
DVTH
THMX
Test Mode Select
(TMS)
t
THDX
Test Data-In
(TDI)
t
TLOV
t
TLOX
Test Data-Out
(TDO)
DON’T CARE
UNDEFINED
NOTE:
Timing for SRAM inputs and outputs is congruent with TDI and TDO, respectively, as shown in Figure 9.
Table 14: TAP DC Electrical Characteristics
Notes 1, 2; 0°C ? TA ? +70°C; VDD ꢂꢀ1.8V 0.1V
DESCRIPTION
SYMBOL
MIN
MAX
UNITS
Clock
tTHTH
fTF
tTHTL
tTLTH
Clock cycle time
100
ns
MHz
ns
10
Clock frequency
Clock HIGH time
Clock LOW time
40
40
ns
Output Times
tTLOX
tTLOV
tDVTH
tTHDX
0
ns
ns
ns
ns
TCK LOW to TDO unknown
20
TCK LOW to TDO valid
TDI valid to TCK HIGH
TCK HIGH to TDI invalid
10
10
Setup Times
tMVTH
tCS
10
10
ns
ns
TMS setup
Capture setup
Hold Times
tTHMX
tCH
10
10
ns
ns
TMS hold
Capture hold
NOTE:
t
1. CS and tCH refer to the setup and hold time requirements of latching data from the boundary scan register.
2. Test conditions are specified using the load in Figure 10.
18Mb: 1.8V VDD, HSTL, QDRIIb4 SRAM
MT54W1MH18J_H.fm – Rev. H, Pub. 3/03
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2003 Micron Technology, Inc.
23
2 MEG x 8, 1 MEG x 18, 512K x 36
1.8V VDD, HSTL, QDRIIb4 SRAM
TAP AC Test Conditions
Figure 10:
TAP AC Output Load Equivalent
Input pulse levels ....................................... VSS to 1.8V
Input rise and fall times......................................... 1ns
Input timing reference levels ...............................0.9V
Output reference levels.........................................0.9V
Test load termination supply voltage ..................0.9V
0.9V
50Ω
TDO
ZO= 50Ω
20pF
Table 15: TAP DC Electrical Characteristics and Operating Conditions
Note 2; 0°C ? TA ? +70°C; VDD ꢂꢀ1.8V 0.1V unless otherwise noted
DESCRIPTION
CONDITIONS
SYMBOL
MIN
MAX
UNITS
NOTES
VIH
VIL
1.3
VDD + 0.3
0.5
V
V
1, 2
1, 2
Input High (Logic 1) Voltage
-0.3
Input Low (Logic 0) Voltage
Input Leakage Current
0V ? VIN ? VDD
ILI
-5.0
-5.0
5.0
5.0
µA
µA
2
2
Output(s) disabled,
ILO
Output Leakage Current
0V ? VIN ? VDD (DQx)
IOLC = 100µA
IOLT = 2mA
VOL1
VOL2
VOH1
VOH1
0.2
0.4
V
V
V
V
1, 2
1, 2
1, 2
1, 2
Output Low Voltage
Output Low Voltage
Output High Voltage
Output High Voltage
IOHC = -100µA
IOHT = -2mA
1.6
1.4
NOTE:
1. All voltages referenced to VSS (GND).
2. This table defines DC values for TAP control and data balls only. The DQ SRAM balls used in JTAG operation will have
the DC values as defined in Table 8, “DC Electrical Characteristics and Operating Conditions,” on page 13.
18Mb: 1.8V VDD, HSTL, QDRIIb4 SRAM
MT54W1MH18J_H.fm – Rev. H, Pub. 3/03
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2003 Micron Technology, Inc.
24
2 MEG x 8, 1 MEG x 18, 512K x 36
1.8V VDD, HSTL, QDRIIb4 SRAM
Table 16: Identification Register Definitions
INSTRUCTION FIELD
ALL DEVICES
DESCRIPTION
Revision number.
REVISION NUMBER (31:28)
DEVICE ID (28:12)
000
00def0wx0t0q0b0s0 def = 010 for 36Mb density
def = 001 for 18Mb density
wx = 11 for x36 width
wx = 10 for x18 width
wx = 01 for x8 width
t = 1 for DLL version
t = 0 for non-DLL version
q = 1 for QDR
q = 0 for DDR
b = 1 for 4-word burst
b = 0 for 2-word burst
s = 1 for separate I/O
s = 0 for common I/O
MICRON JEDEC ID CODE
(11:1)
00000101100
1
Allows unique identification of SRAM vendor.
Indicates the presence of an ID register.
ID Register Presence
Indicator (0)
Table 17: Scan Register Sizes
REGISTER NAME
BIT SIZE
Instruction
Bypass
3
1
ID
32
107
Boundary Scan
Table 18: Instruction Codes
INSTRUCTION
CODE
DESCRIPTION
000
EXTEST
Captures I/O ring contents. Places the boundary scan register between TDI and TDO. This
instruction is not 1149.1-compliant.
001
010
IDCODE
Loads the ID register with the vendor ID code and places the register between TDI and TDO.
This operation does not affect SRAM operations.
SAMPLE Z
Captures I/O ring contents. Places the boundary scan register between TDI and TDO. Forces
all SRAM output drivers to a High-Z state.
011
100
RESERVED
Do Not Use: This instruction is reserved for future use.
SAMPLE/
PRELOAD
Captures I/O ring contents. Places the boundary scan register between TDI and TDO. This
instruction does not implement 1149.1 preload function and is therefore not 1149.1-
compliant.
RESERVED
RESERVED
BYPASS
101
110
111
Do Not Use: This instruction is reserved for future use.
Do Not Use: This instruction is reserved for future use.
Places the bypass register between TDI and TDO. This operation does not affect
SRAM operations.
18Mb: 1.8V VDD, HSTL, QDRIIb4 SRAM
Micron Technology, Inc., reserves the right to change products or specifications without notice.
MT54W1MH18J_H.fm – Rev. H, Pub. 3/03
25
©2003 Micron Technology, Inc.
2 MEG x 8, 1 MEG x 18, 512K x 36
1.8V VDD, HSTL, QDRIIb4 SRAM
Table 19: Boundary Scan (Exit) Order
BIT#
FBGA BALL
BIT#
FBGA BALL
BIT#
FBGA BALL
1
6R
6P
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
10D
9E
73
74
2C
3E
2D
2E
1E
2F
2
3
6N
10C
11D
9C
75
4
7P
76
5
7N
77
6
7R
9D
11B
11C
9B
78
7
8R
79
3F
8
8P
80
1G
1F
9
9R
81
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
11P
10P
10N
9P
10B
11A
10A
9A
8B
82
3G
2G
1J
83
84
85
2J
10M
11N
9M
9N
86
3K
3J
7C
87
6C
88
2K
1K
2L
8A
7A
7B
89
11L
11M
9L
90
91
3L
6B
92
1M
1L
10L
11K
10K
9J
6A
5B
93
94
3N
3M
1N
2M
3P
2N
2P
1P
3R
4R
4P
5P
5N
5R
5A
4A
5C
95
96
9K
97
10J
11J
11H
10G
9G
4B
98
3A
2A
1A
2B
99
100
101
102
103
104
105
106
107
11F
11G
9F
3B
1C
1B
10F
11E
10E
3D
3C
1D
18Mb: 1.8V VDD, HSTL, QDRIIb4 SRAM
MT54W1MH18J_H.fm – Rev. H, Pub. 3/03
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2003 Micron Technology, Inc.
26
2 MEG x 8, 1 MEG x 18, 512K x 36
1.8V VDD, HSTL, QDRIIb4 SRAM
Figure 11:
165-Ball FBGA
0.85 0.075
0.12
C
SEATING PLANE
C
BALL A11
165X Ø 0.45
10.00
SOLDER BALL DIAMETER REFERS
TO POST REFLOW CONDITION. THE
PRE-REFLOW DIAMETER IS Ø 0.40
BALL A1
PIN A1 ID
1.20 MAX
1.00
TYP
PIN A1 ID
7.50 0.05
14.00
15.00 0.10
7.00 0.05
1.00
TYP
MOLD COMPOUND: EPOXY NOVOLAC
SUBSTRATE: PLASTIC LAMINATE
6.50 0.05
5.00 0.05
13.00 0.10
SOLDER BALL MATERIAL: EUTECTIC 63% Sn, 37% Pb
SOLDER BALL PAD: Ø .33mm
NOTE:
1. All dimensions are in millimeters.
Data Sheet Designation
No Marking: This data sheet contains minimum and maximum limits specified over the complete power
supply and temperature range for production devices. Although considered final, these specifications are sub-
ject to change, as further product development and data characterization sometimes occur.
®
8000 S. Federal Way, P.O. Box 6, Boise, ID 83707-0006, Tel: 208-368-3900
E-mail: prodmktg@micron.com, Internet: http://www.micron.com, Customer Comment Line: 800-932-4992
Micron, the M logo, and the Micron logo are trademarks and/or service marks of Micron Technology, Inc.
QDR RAMs and Quad Data Rate RAMs comprise a new family of products developed by Cypress Semiconductor, IDT, and Micron Technology, Inc.,
NEC, and Samsung.
18Mb: 1.8V VDD, HSTL, QDRIIb4 SRAM
MT54W1MH18J_H.fm – Rev. H, Pub. 3/03
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2003 Micron Technology, Inc.
27
2 MEG x 8, 1 MEG x 18, 512K x 36
1.8V VDD, HSTL, QDRIIb4 SRAM
Document Revision History
Rev. H, Pub 3/03 ..............................................................................................................................................................3/03
•
•
Updated JTAG Section
Removed Preliminary Status
Rev. G, Pub 2/03...............................................................................................................................................................2/03
•
•
•
•
•
•
•
•
•
Added definitive notes to Figure 3
Added definitive note to Table 9
Added definitive note concerning bit# 64 to Table 19
Removed Errata specifications
Updated AC timing values with new codevelopment values
Updated JTAG description to reflect 1149.1 specification compliance with EXTEST feature
Added definitive note concerning SRAM (DQ) I/O balls used for JTAG DC values and timing
Changed process information in header to die revision indicator
Updated Thermal Resistance Values to Table 12:
CI = 4.5 TYP; 5.5 MAX
CO = 6 TYP; 7 MAX
CCK = 5.5 TYP; 6.5 MAX
•
•
Updated Thermal Resistance values to Table 12:
JA = 19.4 TYP
JC = 1.0 TYP
JB = 9.6 TYP
Added TJ ? +95°C to Table 13
•
•
•
•
•
•
Modified Figure 2 regarding depth, configuration, and byte controls
Added definitive notes regarding I/O behavior during JTAG operation
Added definitive notes regarding IDD test conditions for read to write ratio
Removed note regarding AC derating information for full I/O range
Remove references to JTAG scan chain logic levels being at logic zero for NC pins in Tables 5 and 19
Revised ball description for NC balls:
These balls are internally connected to the die, but have no function and may be left not connected to the
board to minimize ball count.
Rev. 6, Pub 9/02 ...............................................................................................................................................................9/02
Reverted data sheet to PRELIMINARY designation
•
Rev. 5, Pub. 9/02, ADVANCE ...........................................................................................................................................9/02
•
•
•
•
Added new Output Times values
Added Errata to back of data sheet
Removed ADVANCE designation
Removed TJ references
Rev. 4, Pub. 8/02, ADVANCE ...........................................................................................................................................8/02
Updated format
•
Rev. 3, Pub. 12/01, ADVANCE .......................................................................................................................................12/01
Changed AC timing
•
Rev. 2, Pub. 11/01, ADVANCE .......................................................................................................................................11/01
New ADVANCE data sheet
•
18Mb: 1.8V VDD, HSTL, QDRIIb4 SRAM
MT54W1MH18J_H.fm – Rev. H, Pub. 3/03
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2003 Micron Technology, Inc.
28
相关型号:
©2020 ICPDF网 联系我们和版权申明