ES7 [CYRUSTEK]
True RMS-to-DC Converters; 真RMS - DC转换器
| 型号： | ES7 |
| 厂家： | 
Cyrustek corporation |
| 描述： | True RMS-to-DC Converters |
| 文件： | 总10页 (文件大小：921K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
ES7
True RMS-to-DC Converters
Features
•
True RMS-to-DC Conversion
Description
•
Input level is specified up to
400mVRMS
The ES7 series are designed for the true
RMS-to-DC conversion. ES7 accept
low-level input signals from 0 to 400 mV
RMS complex input waveforms. ES7 can be
operated form either a single supply or
dual supplies. The device draw less than 1
mA of quiescent supply current,
furthermore, an enable pin is provided to
turn-off the device, making it ideal for
battery-powered applications.
•
•
•
Averaging capacitor is typically 2.2uF
Positive output voltage
Computes RMS of AC and DC
Signals
• Single or Dual Supply Operation
• Low Cost
• Power-Down Function
•
•
Low Power: 600μA typically
Wide power supply range : from ±
2.5V to ±10V
Application
* Digital Multi-Meters
* Battery-Powered Instruments
* Panel Meter
•
8-pin SOP package
1
09/07/08
ES7
True RMS-to-DC Converters
Pin Assignment: ES7
1 RL
COM 8
+Vs 7
Vout 6
2 Vin
3 PwrDown
-Vs
5
4
Cav
SOP 8 Pin Package
Pin Description
Pin No
Symbol
Type
-
I
I
P
Description
RL terminal. For zero-offset removing.
Measurement input.
Pull high (+Vs) to enable power-down function.
Negative supply voltage.
1
2
3
4
5
6
7
8
RL
Vin
PwrDown
-Vs
Cav
Vout
+Vs
COM
I/O Averaging capacitor
O
P
P
Measurement output.
Positive supply voltage.
Power ground
I: input, O: output, P: power
2
09/07/08
ES7
True RMS-to-DC Converters
Absolute Maximum Ratings
Supply Voltage: Dual Supplies ......…………………………….….... ±10V
Single Supply ..……………………...…….....……+20V
Input Voltage: ...................………………………….……………..... ±10V
Power Dissipation (Package)
SOP………………………………………………………………...450mW
Operating Temperature Range
.......……………………………….......0℃ to +70℃
Storage Temperature Range.....…………………...……………............-55℃ to +150℃
Lead Temperature (Soldering, 10sec)....…………………………………...............300℃
Electrical Characteristics-ES7
(TA= +25℃, Vs = +3V, -Vs = -3V, unless otherwise noted.)
PARAMETER
Transfer Equation
CONDITIONS
MIN
TYP
MAX
UNITS
VOUT = avg.[(VIN)2]
ms/μF CAV
Averaging Time Constant
6
CONVERSION ACCURACY
Total Error, Internal Trim
(Notes 1)
mV ±% of
Reading
ES7
±0.5 ± 1.0
Total Error vs. Temperature (0
℃ to + 70℃)
mV ±% of
Reading/℃
±0.1 ±0.01
±0.1 ±0.01
mV ±% of
Reading/V
Total Error vs. Supply
±% of
Reading
Total Error vs. DC Reversal
VIN=+400mV
±2.0
Crest Factor = 1 400mV
Specified Accuracy
200mV
Crest Factor = 2
400mV
200mV
Crest Factor = 3
400mV
200mV
Crest Factor = 4
400mV
1.00
1.10
1.25
1.50
1.50
2.00
±% of
Reading
Cav=2.2μF
Additional Error (Note 2)
FREQUENCY RESPONSE
35mV
100mV
200mV
400mV
35mV
50
200
200
200
1.0
1.0
1.0
0.5
Bandwidth for 1% Additional
Error (0.09dB)
kHz
100mV
200mV
400mV
±3dB Bandwidth
MHz
3
09/07/08
ES7
True RMS-to-DC Converters
Electrical Characteristics-ES7 (continued)
(TA= +25℃, Vs = +3V, -Vs = -3V, unless otherwise noted.)
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
INPUT CHARACTERISTICS
Continuous RMS, All Supplies
0 to 400
mVRMS
VPK
±2.5V Supplies
1
Input Signal range
Peak Transient
±3V Supplies
±5V Supplies
1.5
2.8
10
MΩ
Input Resistance
6
8
Input Offset Voltage (Note3)
ES7
±0.5
mV
OUTPUT CHARACTERISTICS
+3V, -3V Supplies
±5V to ±10V Supplies
1
1
8
Output Voltage Swing
VRMS
1.5
10
kΩ
Output Resistance
Power SUPPLY
Rated Performance
Dual Supplies
12
±3
V
V
±2.5
+5
±10
+20
800
75
Single Supply
V
μA
μA
Supply Current
±3V Supply. Vin connects to COM
600
60
Supply Current (Power Down) Pin3 connects to V+
Note 1: Accuracy is specified for 0 to 400mV, 1kHz sine-wave input. Accuracy is degraded at higher RMS signal levels.
Note 2: Error vs. crest factor is specified as an additional error for 200mVRMS and 400mVRMS rectangular pulse input, pulse width =
200μs
Note 3: The input offset voltage can be reduced or canceled by an external 500kohm variable resistor shown in Figure
3.
4
09/07/08
ES7
True RMS-to-DC Converters
Detailed Description
Figure 1 shows the simplified schematic of ES7. It consists of four major sub-circuits:
absolute value circuit (rectifier), square/divider, current mirror and buffer amplifier. The
actual computation performed by the ES7 follows the equation:
V
= Avg. [V 2／V
]
RMS
IN
RMS
The input voltage, V , applied to the ES7 is converted to a unipolar current I (Figure
IN
1
1) by the absolute-value/voltage. This current drives one input of the squarer/divider
that produces a current I , which has the transfer function:
4
Ι12
Ι4 =
Ι3
The current I drives the internal current mirror through a low-pass filter formed by R1
4
and the external capacitor, C . As long as the time constant of this filter is greater than
AV
the longest period of the input signal, I is averaged. The current mirror returns a
4
current, I , to the square/divider to complete the circuit. The current I is then a function
3
4
2
of the average of (I / I ), which is equal to I .
1RMS
1
4
The current mirror also produces a 2．I output current, I
, that can be used directly
4
OUT
or converted to a voltage using resistor R2 and the internal buffer to provide a
low-impedance voltage output. The transfer function for the ES7 is:
V
= 2．R2．I
= V
RMS IN
OUT
5
09/07/08
ES7
True RMS-to-DC Converters
Standard Connection for ES7 (Figure 2)
The standard RMS connection requires only two external components, Rin and C .
av
Other components shown in figure 2 are optional. In this configuration, ES7 measure
the RMS of the AC and DC levels present at the input, but shows an error for
low-frequency inputs as a function of the C filter capacitor. Figure 4 gives practical
av
values of C for various values of averaging error over frequency for the standard
av
RMS connections (no post filtering). If a 3uF capacitor is chosen, the additional error at
30Hz will be 1%. If the DC error can be rejected, a capacitor Ccp should be connected
in series with the input, as would typically be the case in single-supply operation.
+Vs
RL
1
COM 8
SW1
Absolute
Value
Vin
+
4.7μ
CF (Optional)
4.7μ
2 Vin
+Vs
7
Ccp
Rin
Square
Divider
47k
Vout
3 PwrDown
Vout 6
Cav 5
Current
Mirror
Cav
+
-Vs
4
2.2μ
-Vs
Figure 2. Standard connection for ES7.
Note:
1. SW1 is opened for AC-coupled operation, or closed for direct input.
2. PwrDown pin is pulled to –Vs or keeps floating for normal operation. Connect it to
+Vs will force ES7 to enter power down mode.
6
09/07/08
ES7
True RMS-to-DC Converters
To Adjust the zero-offset of ES7 (Figure 3)
The output of some ES7 ICs may have an offset voltage when the input is zero. The
amount of this offset voltage might be different in every ES7. We provide pin1-RL to
achieve the reduction of zero offset voltage. The test circuit is shown as below. The
500kohm VR, 1kohm and 10ohm resistors are used to reduce zero offset voltage.
Adjusting the 500kohm VR can reduce the zero offset voltage. However it must be
noted that the 10ohm resistor enlarge the output impedance. The voltage of pin6-Vout is
equal to (output current)*(output impedance), so it would be enlarged too. This will
cause an additional error for ES7. So we recommend that the value of resistor between
pin1-RL and pin8-COM should not be too large.
500k3
-Vs
+Vs
1k
10
RL
1
COM 8
SW11
Absolute
Value
+
4.7μ
CF (Optional)
4.7μ
2 Vin
+Vs
7
Ccp
Rin
Vin
Square
Divider
47k
PwrDown2
-Vs
Vout
3
Vout 6
Cav 5
Current
Mirror
Cav
+
4
2.2μ
-Vs
Figure 3. Adjust the zero-offset
Note:
1. SW1 is opened for AC-coupled operation, or closed for direct input.
2. PwrDown pin is pulled to –Vs or keeps floating for normal operation. Connect it to
+Vs will force ES7 to enter power down mode.
3. The 500k ohm variable resistor can be used to adjust the zero-offset voltage.
7
09/07/08
ES7
True RMS-to-DC Converters
Application notes
1. AC-coupled operation
Refer to the standard circuit of ES7 shown in Figure 2~3. ES7 will work in an
AC-coupled operation when the SW1 is opened. In AC-coupled operation, an
AC-coupled capacitor (Ccp) and bias resistors Rin must be required. For a low
frequency input under 100Hz, the Ccp need a 1uF or even larger capacitor to prevent
input signal from decaying.
Due to the architecture of ES7, a bias current is needed to activate the input buffer. The
resistor Rin applied from Vin to GND supplies a bias current flow path in AC-coupled
operation. The bias current flows from GND to Vin through Rin will cause a bias
voltage at Vin pin. So the Rin resistance should not be too large (cause an additional
zero offset) or too small (low input impedance).
2. Power Down Function
The ES7 provides a power-down enable pin (Pin 3). To enable the device, this pin must
be connected to –Vs or keep floating. If it is connected to V+, the device will enter
power-down mode.
3. Post Filter CF
To reduce the output ripple of ES7, a post filter capacitor CF is required. This capacitor
should be connected as shown in figure 2. With post filter, the value of Cav should be
just large enough to give the maximum dc error at the lowest frequency of interest. And
the output ripple will be removed by the post filter.
8
09/07/08
ES7
True RMS-to-DC Converters
Choosing the Averaging Time Constant
The ES7 computes the RMS value of AC and DC signals. At low frequencies and DC,
the output tracks the input exactly; at higher frequencies, the average output approaches
the RMS value of the input signal. The actual output differs from the ideal by an
average (or DC) error plus some amount of ripple.
The DC error term is a function of the value of C and the input signal frequency. The
av
output ripple is inversely proportional to the value of C . Waveforms with high crest
av
factors, such as a pulse train with low duty cycle, should have an average time constant
chosen to be at least ten times the signal period.
Using a large value of C to remove the output ripple increases the setting time for a
av
step change in the input signal level. Figure 4 shows the relationship between C and 1
av
% settling time, where 110ms settling equals 4uF of C . The settling time, or time for
av
the RMS converter to settle to within a given percent of the change in RMS level, is set
by the averaging time constant, which varies approximately 2:1 between decreasing and
increasing input signals. In addition, the settling time also varies with input signal
levels, increasing as the input signal is reduced, and decreasing as the input is
increased.
t
m
g
4
9
09/07/08
ES7
True RMS-to-DC Converters
Packaging
8 Pin SOP Package
Dimension Parameters
10
09/07/08
相关型号：
©2020 ICPDF网 联系我们和版权申明