LM1117-5.0M3 [CYSTEKEC]
1A Low Dropout Positive Voltage Regulator;型号: | LM1117-5.0M3 |
厂家: | CYSTECH ELECTONICS CORP. |
描述: | 1A Low Dropout Positive Voltage Regulator |
文件: | 总7页 (文件大小:372K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Spec. No. : C506M3
Issued Date : 2007.07.10
Revised Date :2013.06.19
Page No. : 1/7
CYStech Electronics Corp.
1A Low Dropout Positive Voltage Regulator
LM1117M3 series
Features
Description
●
●
●
●
●
●
Adjustable or Fixed Output
Output Current of 1A
Low Dropout, 1.4V max at 1A Output Current efficiency. All internal circuitry is designed to
Good Noise Rejection
Output Current Limiting
Built-in Thermal Shutdown
Fast Transient Response
Can operate using MLCCs in the capacitance
range of 2μF to 10μF
The LM1117 series of positive adjustable and fixed
regulators are designed to provide 1A with high
operate down to 1.4V input to output differential.
The product is specifically designed to provide well-
regulated supply for low-voltage IC application such
as high-speed bus termination and low current 3.3V
logic supply, and other applications such as VGA cards.
●
●
Applications
●
●
●
High Efficiency Linear Regulators
Post Regulators for Switching Supplies
Adjustable Power Supply
Typical Application Data
Fixed Voltage Regulator
TAB
VIN>4.75V
VOUT=3.3V
3
2
OUT
IN
+
GND
1
C1
10μF, Tan.
+
C2
10μF, Tan. Min
Notes:
1)C1 needed if device is far from filter capacitors
2)C2 minimum value requir ed for stability
Adjustable Voltage Regulator
TAB
VIN>4.75V
VOUT=3.45V
3
2
OUT
IN
ADJ
1
R1
133Ω,1%
+
C1
10μF, Tan.
+
C2
10μF, Tan. Min
R2
232Ω, 1%
VOUT=VREF×(1+R2/R1)+IADJ×R2
Notes:
1)C1 needed if device is far from filter capacitors
2)C2 minimum value required for stability
LM1117M3 series
CYStek Product Specification
Spec. No. : C506M3
Issued Date : 2007.07.10
Revised Date :2013.06.19
Page No. : 2/7
CYStech Electronics Corp.
Package Information
Pin
1
2
Name
ADJ/GND
OUTPUT
INPUT
1
2
3
3
SOT-89
Absolute Maximum Ratings
Symbol
Parameter
Maximum
Units
PD
VIN
TOPR
Power Dissipation
Input Voltage
Operating Junction Temperature Range
330
-0.3 ~ +15
-40 ~ +125
mW
V
℃
TSTG
TMJ
Storage Temperature
Maximum Junction Temperature
-65 ~ +150
150
℃
℃
Device Selection Guide
Device
Output Voltage
Adjustable
1.5V
Package
SOT-89
Shipping
LM1117-ADJM3
LM1117-1.5M3
LM1117-1.8M3
LM1117-2.5M3
LM1117-3.3M3
LM1117-5.0M3
1.8V
2.5V
3.3V
5.0V
(Pb-free lead plating and 1000 pcs / Tape & Reel
halogen-free package)
Block Diagram
LM1117M3 series
CYStek Product Specification
Spec. No. : C506M3
Issued Date : 2007.07.10
Revised Date :2013.06.19
Page No. : 3/7
CYStech Electronics Corp.
Electrical Characteristics @ IO=10mA,TJ=25℃, unless otherwise specified
Parameter
Device
Test Conditions
Min Typ Max Units
Reference voltage
Adj version
1.225 1.250
1.275
VIN-VOUT=1.5V
V
3.0V≤VIN≤12V
3.3V≤VIN≤12V
4.0V≤VIN≤12V
4.8V≤VIN≤12V
6.5V≤VIN≤12V
1.470 1.500 1.530
1.764 1.800 1.836
2.450 2.500 2.550
3.235 3.300 3.365
4.900 5.000 5.100
V
V
V
V
V
%
Output Voltage
LM1117-1.5
LM1117-1.8
LM1117-2.5
LM1117-3.3
LM1117-5.0
Line Regulation
All version VOUT+1.5V≤VIN≤12V
-
-
-
-
-
-
-
-
0.2
1
Load Regulation
(Note 1, 2)
LM1117-ADJ VIN=3.3V, Vadj=0, 10mA≤IO≤1A
-
%
VIN=3.0V, 0mA≤IO≤1A
VIN=3.3V, 0mA≤IO≤1A
VIN=4.0V, 0mA≤IO≤1A
VIN=5.0V, 0mA≤IO≤1A
VIN=8.0V, 0mA≤IO≤1A
12
15
20
26
40
15
18
25
33
50
mV
mV
mV
mV
mV
LM1117-1.5
LM1117-1.8
LM1117-2.5
LM1117-3.3
LM1117-5.0
Dropout Voltage
All version
IO=1A (ΔVOUT=1%VOUT)
-
1.3
-
1.4
-
V
A
(VIN-VOUT)
Current Limit
All version VIN-VOUT=5V
Adj version VIN=5V
1.1
Minimum Load
Current
-
5
10
mA
Adjust Pin Current
Quiescent Current
Adj version VIN=12V, IO=10mA
Fixed version VIN=12V, IO=0mA
-
-
50
-
100
12
μA
mA
All version
All version
-
60
-
0.008 0.04 %/W
TA=25℃, 30ms pulse
Thermal Regulation
Ripple Rejection
f=120Hz, VIN=VOUT+3V, IO= 1A,
70
-
-
dB
%
COUT=25μF tantalum
Temperature Stability
All version IO= 10mA
All version
0.5
Thermal Resistance,
Junction to Ambient(
No heat sink, no air
flow)
-
-
300
100
-
-
℃/W
℃/W
Thermal Resistance,
Junction to Case
All version Control Circuitry/ Power transistor
Note : 1.See thermal regulation specifications for changes in output voltage due to heating effects. Line and load regulation are measured at
a constant junction temperature by low duty cycle pulse testing. Load regulation is measured at the output lead 1/18” from the
package.
2. Line and load regulation are guaranteed up to the maximum power dissipation of 3W. Power dissipation is determined by the
difference in input and output and the output current. Guaranteed maximum power dissipation will not be available over the full
input/output range.
LM1117M3 series
CYStek Product Specification
Spec. No. : C506M3
Issued Date : 2007.07.10
Revised Date :2013.06.19
Page No. : 4/7
CYStech Electronics Corp.
Characteristic Curves
GND
LM1117M3 series
CYStek Product Specification
Spec. No. : C506M3
Issued Date : 2007.07.10
Revised Date :2013.06.19
Page No. : 5/7
CYStech Electronics Corp.
Reel Dimension
Carrier Tape Dimension
LM1117M3 series
CYStek Product Specification
Spec. No. : C506M3
Issued Date : 2007.07.10
Revised Date :2013.06.19
Page No. : 6/7
CYStech Electronics Corp.
Recommended wave soldering condition
Product
Peak Temperature
Soldering Time
5 +1/-1 seconds
Pb-free devices
260 +0/-5 °C
Recommended temperature profile for IR reflow
Profile feature
Average ramp-up rate
(Tsmax to Tp)
Sn-Pb eutectic Assembly
Pb-free Assembly
3°C/second max.
3°C/second max.
Preheat
−Temperature Min(TS min)
−Temperature Max(TS max)
−Time(ts min to ts max)
100°C
150°C
60-120 seconds
150°C
200°C
60-180 seconds
Time maintained above:
−Temperature (TL)
− Time (tL)
183°C
60-150 seconds
240 +0/-5 °C
217°C
60-150 seconds
260 +0/-5 °C
Peak Temperature(TP)
Time within 5°C of actual peak
temperature(tp)
10-30 seconds
20-40 seconds
Ramp down rate
6°C/second max.
6°C/second max.
6 minutes max.
8 minutes max.
Time 25 °C to peak temperature
Note : All temperatures refer to topside of the package, measured on the package body surface.
LM1117M3 series
CYStek Product Specification
Spec. No. : C506M3
Issued Date : 2007.07.10
Revised Date :2013.06.19
Page No. : 7/7
CYStech Electronics Corp.
SOT-89 Dimension
Marking:
A
Vout:
1.5V→-15
1.8V→-18
2.5V→-25
3.3V→-33
5.0V→-50
ADJ→
Device
Name
2
1
3
1117□□□
□□□□
Date
Code
H
C
blank
D
B
E
Style: Pin 1. GND/ADJ 2. VOUT 3. VIN
I
F
G
3-Lead SOT-89 Plastic
Surface Mounted Package
CYStek Package Code: M3
*: Typical
Inches
Min. Max.
Millimeters
Inches
Min. Max.
0.0583 0.0598
0.1165 0.1197
0.0551 0.0630
0.0138 0.0161
Millimeters
DIM
DIM
Min.
Max.
4.60
4.25
1.70
2.60
0.51
Min.
Max.
1.527
3.04
1.60
0.41
A
B
C
D
E
0.1732 0.1811
0.1594 0.1673
0.0591 0.0663
0.0945 0.1024
0.01417 0.0201
4.40
4.05
1.50
2.40
0.36
F
G
H
I
1.48
2.96
1.40
0.35
Notes: 1.Controlling dimension: millimeters.
2.Maximum lead thickness includes lead finish thickness, and minimum lead thickness is the minimum thickness of base material.
3.If there is any question with packing specification or packing method, please contact your local CYStek sales office.
Material:
• Lead: Pure tin plated.
• Mold Compound: Epoxy resin family, flammability solid burning class: UL94V-0
Important Notice:
• All rights are reserved. Reproduction in whole or in part is prohibited without the prior written approval of CYStek.
• CYStek reserves the right to make changes to its products without notice.
• CYStek semiconductor products are not warranted to be suitable for use in Life-Support Applications, or systems.
• CYStek assumes no liability for any consequence of customer product design, infringement of patents, or application assistance.
LM1117M3 series
CYStek Product Specification
相关型号:
LM1117-5.0MDC
IC VREG 5 V FIXED POSITIVE LDO REGULATOR, 1.3 V DROPOUT, UUC, DIE, Fixed Positive Single Output LDO Regulator
NSC
©2020 ICPDF网 联系我们和版权申明