DS1631A [DALLAS]
High-Precision Digital Thermometer and Thermostat; 高精度数字温度计和温度监控器
| 型号： | DS1631A |
| 厂家： | 
DALLAS SEMICONDUCTOR |
| 描述： | High-Precision Digital Thermometer and Thermostat |
| 文件： | 总14页 (文件大小：243K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
DS1631/DS1631A/DS1731
High-Precision Digital
Thermometer and Thermostat
www.maxim-ic.com
FEATURES
PIN CONFIGURATIONS
C DS1631 and DS1631A Provide M0.5°C
Accuracy over a 0°C to +70°C Range
C DS1731 Provides M1°C Accuracy over a
-10°C to +85°C Range
7
6
1
2
3
VDD
A0
A1
SCL
TOUT
GND
C DS1631A Automatically Begins Taking
Temperature Measurements at Power-Up
C Operating Temperature Range: -55°C to
+125°C (-67°F to +257°F)
4
A2
ꢀSOP
(DS1631U, DS1631AU, DS1731U)
C Temperature Measurements Require No
External Components
VDD
A0
1
2
3
4
C Output Resolution is User-Selectable to 9,
10, 11, or 12 Bits
7
6
SCL
TOUT
GND
C Wide Power-Supply Range (+2.7V to +5.5V)
C Converts Temperature-to-Digital Word in
750ms (max)
A1
A2
C Multidrop Capability Simplifies Distributed
Temperature-Sensing Applications
C Thermostatic Settings are User-Definable
and Nonvolatile (NV)
SO (150mil)
(DS1631Z)
See Table 2 for Pin Descriptions
C Data is Read/Written Through 2-Wire Serial
Interface (SDA and SCL Pins)
APPLICATIONS
C All Three Devices are Available in 8-Pin
ꢀSOP Packages and the DS1631 is Also
Available in a 150mil SO package—see
Table 1 for Ordering Information
C Network Routers and Switches
C Cellular Base Stations
C Portable Products
C Any Space-Constrained Thermally Sensitive
Product
DESCRIPTION
The DS1631, DS1631A, and DS1731 digital thermometers provide 9, 10, 11, or 12-bit temperature
readings over a -55°C to +125°C range. The DS1631 and DS1631A thermometer accuracy is M0.5°C
from 0°C to +70°C with 3.0V ? VDD ? 5.5V, and the DS1731 accuracy is M1°C from -10°C to +85°C with
3.0V ? VDD ? 5.5V. The thermostat on all three devices provides custom hysteresis with user-defined trip
points (TH and TL). The TH and TL registers and thermometer configuration settings are stored in NV
EEPROM so they can be programmed prior to installation. In addition, the DS1631A automatically
begins taking temperature measurements at power-up, which allows it to function as a stand-alone
thermostat. Communication with the DS1631/DS1631A/DS1731 is achieved through a 2-wire serial
interface, and three address pins allow up to eight devices to be multidropped on the same 2-wire bus.
Pin descriptions for the DS1631/DS1631A/DS1731 are provided in Table 2 and user-accessible registers
are summarized in Table 3. A functional diagram is shown in Figure 1.
1 of 14
092502
DS1631/DS1631A/DS1731
Table 1. ORDERING INFORMATION
ORDERING
PACKAGE
MARKING
D1631
DESCRIPTION
DS1631 in 8-Pin ꢀSOP
NUMBER
DS1631U
DS1631U/T&R
DS1631Z
D1631
DS1631 in 8-Pin ꢀSOP, 3000-Piece Tape-and-Reel
DS1631 in 150mil 8-Pin SO
DS1631Z
DS1631Z
1631A
DS1631Z/T&R
DS1631AU
DS1631 in 150mil 8-Pin SO, 2500-Piece Tape-and-Reel
DS1631A in 8-Pin ꢀSOP
DS1631AU/T&R
DS1731U
1631A
DS1631A in 8-Pin ꢀSOP, 3000-Piece Tape-and-Reel
DS1731 in 8-Pin ꢀSOP
D1731
DS1731U/T&R
D1731
DS1731 in 8-Pin ꢀSOP, 3000-Piece Tape-and-Reel
Table 2. DETAILED PIN DESCRIPTION
PIN
SYMBOL
SDA
SCL
TOUT
GND
A2
DESCRIPTION
Data Input/Output Pin for 2-Wire Serial Communication Port. Open-Drain.
Clock Input Pin for 2-Wire Serial Communication Port.
Thermostat Output Pin. Push-Pull.
Ground Pin
1
2
3
4
5
Address Input Pin
6
A1
Address Input Pin
7
A0
VDD
Address Input Pin
8
Supply Voltage Pin. +2.7V to +5.5V Power-Supply Pin.
Figure 1. FUNCTIONAL DIAGRAM
CONFIGURATION REGISTER
VDD
AND CONTROL LOGIC
TEMPERATURE SENSOR
SCL
and ꢀꢁ ADC
ADDRESS
AND
TEMPERATURE REGISTER
TH REGISTER
I/O CONTROL
1
2
DIGITAL
TOUT
COMPARATOR/LOGIC
GND
TL REGISTER
2 of 14
DS1631/DS1631A/DS1731
ABSOLUTE MAXIMUM RATINGS*
Voltage on any Pin Relative to Ground
Operating Temperature Range
Storage Temperature Range
-0.5V to +6.0V
-55°C to +125°C
-55°C to +125°C
Solder Dip Temperature (10s)
Reflow Oven Temperature
See IPC/JEDEC J-STD-020A Specification
+220°C
* These are stress ratings only and functional operation of the device at these or any other conditions
above those indicated in the operation sections of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods of time may affect reliability.
DC ELECTRICAL CHARACTERISTICS
(VDD = 2.7V to 5.5V; TA = -55°C to +125°C.)
PARAMETER
SYMBOL
CONDITION
MIN
MAX
UNITS NOTES
Supply Voltage
VDD
2.7
5.5
V
1
0°C to +70°C,
3.0V ? VDD ? 5.5V
0°C to +70°C,
2.7V ? VDD ꢁ 3.0V
-55°C to +125°C
-10°C to +85°C,
3.0V ? VDD ? 5.5V
-10°C to +85°C,
2.7V ? VDD ꢁ 3.0V
-55°C to +125°C
±0.5
DS1631, DS1631A
Thermometer Error
TERR
°C
2
±1
±2
±1
DS1731
TERR
°C
2
Thermometer Error
±1.5
±2
Low-Level Input
Voltage
High-Level Input
Voltage
SDA Low-Level
Output Voltage
Input Current Each
I/O Pin
VIL
VIH
-0.5
0.3 x VDD
V
V
0.7 x
VDD
0
VDD + 0.3
VOL1
VOL2
3mA sink current
6mA sink current
0.4
0.6
V
0
0.4 < VI/O < 0.9VDD
-10
+10
µA
Temperature
conversion
1
-55°C to +85°C
Temperature
conversion
mA
Active Supply
Current
IDD
3
4
1.25
+85°C to +125°C
E2 write
400
110
µA
nA
Communication only
Standby Supply
Current
ISTBY
0°C to +70°C
800
VOH
VOL
1mA source current
4mA sink current
2.4
V
V
1
1
TOUT Output Logic
Voltage
0.4
3 of 14
DS1631/DS1631A/DS1731
AC ELECTRICAL CHARACTERISTICS
(VDD = 2.7V to 5.5V; TA = -55°C to +125°C.)
PARAMETER
SYMBOL CONDITION
9-bit resolution
10-bit
MIN
TYP MAX UNITS NOTES
93.75
187.5
resolution
Temperature
tTC
ms
11-bit
Conversion Time
375
resolution
12-bit
750
resolution
SCL Frequency
Bus Free Time
fSCL
tBUF
0
400
kHz
µs
Between a STOP and
START Condition
START and Repeated
START Hold Time
from Falling SCL
Low Period of SCL
High Period of SCL
Repeated START
Condition Setup Time
to Rising SCL
1.3
5
tHD:STA
0.6
µs
5, 6
tLOW
tHIGH
1.3
0.6
µs
µs
5
5
tSU:STA
0.6
0
µs
5
Data-Out Hold Time
from Falling SCL
Data-In Setup Time to
Rising SCL
tHD:DAT
tSU:DAT
tR
0.9
µs
ns
ns
ns
µs
pF
5
5
100
Rise Time of SDA and
SCL
20 + 0.1CB
20 + 0.1CB
0.6
1000
300
5, 7
5, 7
5
Fall Time of SDA and
SCL
tF
STOP Setup Time to
Rising SCL
tSU:STO
Capacitive Load for
Each Bus Line
CB
400
50
I/O Capacitance
Input Capacitance
Spike Pulse Width that
can be Suppressed by
Input Filter
CI/O
CI
10
5
pF
pF
tSP
0
ns
NOTES:
1) All voltages are referenced to GND.
2) See Figure 2 for Typical Operating Curves.
3) Specified with TOUT pin open; A0, A1, A2 = 0V or VDD; and fSCL O 2Hz.
4) Specified with temperature conversions stopped; TOUT pin open; SDA = VDD; SCL = VDD; and A0, A1,
A2 = 0V or VDD.
5) See Timing Diagram in Figure 3. All timing is referenced to 0.9 x VDD and 0.1 x VDD.
6) After this period the first clock pulse is generated.
7) For example, if CB = 300pF, then tR[min] = tF[min] = 50ns.
4 of 14
DS1631/DS1631A/DS1731
EEPROM AC ELECTRICAL CHARACTERISTICS
(VDD = 2.7V to 5.5V; TA = -55°C to +125°C.)
PARAMETER
EEPROM Write Cycle Time
EEPROM Writes
SYMBOL
twr
CONDITION
MIN
TYP
MAX UNITS
4
10
ms
Writes
Years
NEEWR
tEEDR
-55°C to +55°C
-55°C to +55°C
50k
10
EEPROM Data Retention
Figure 2. TYPICAL OPERATING CURVES
DS1631/DS1631A
DS1731
0.8
0.8
0.6
0.4
0.2
0
0.6
0.4
0.2
+3
ꢀꢁ
+3
ꢀꢁ
0
Mean
20
Mean
-0.2
-0.2
-0.4
-0.6
-0.8
-3
ꢀꢁ
-0.4
-0.6
-0.8
-3
ꢀꢁ
-10
0
10
30
40
50
60
70
80
0
10
20
30
40
50
60
70
REFERENCE TEMPERATURE (LC)
REFERENCE TEMPERATURE (LC)
Figure 3. TIMING DIAGRAM
All timing is referenced to 0.9 x VDD and 0.1 x VDD.
5 of 14
DS1631/DS1631A/DS1731
Table 3. REGISTER SUMMARY
REGISTER NAME
SIZE
MEMORY
REGISTER CONTENTS
(USER ACCESS)
(BYTES)
TYPE
AND POWER-UP STATE
Measured temperature in two’s complement
format.
Temperature
(Read Only)
2
2
2
SRAM
Power-up state: -60ºC (1100 0100 0000 0000)
Upper alarm trip point in two’s complement
format.
TH
EEPROM
EEPROM
(Read/Write)
Power-up state: user defined.
Lower alarm trip point in two’s complement
format.
TL
(Read/Write)
Power-up state: user defined.
Configuration and status information. Unsigned
data.
Configuration
(Various bits are
Read/Write and Read
Only—See Table 5)
SRAM,
1
6 MSbs = SRAM
EEPROM
2 LSbs (POL and 1SHOT bits) = EEPROM
Power-up state: 100011XX (XX = user defined)
OPERATION—MEASURING TEMPERATURE
The DS1631, DS1631A, and DS1731 measure temperature using bandgap-based temperature sensors. A
delta-sigma analog-to-digital converter (ADC) converts the measured temperature to a 9-, 10-, 11-, or 12-
bit (user-selectable) digital value that is calibrated in LC; for LF applications a lookup table or conversion
routine must be used. Throughout this data sheet, the term “conversion” is used to refer to the entire
temperature measurement and ADC sequence.
The DS1631 and DS1731 always power-up in a low-power idle state, and the Start Convert T command
must be used to initiate conversions. The DS1631A always begins conversions automatically at power-
up.
The DS1631, DS1631A, and DS1731 can be programmed to perform continuous consecutive conversions
(continuous-conversion mode) or to perform single conversions on command (one-shot mode). The
conversion mode is programmed through the 1SHOT bit in the configuration register as explained in the
CONFIGURATION REGISTER section of this data sheet. In continuous-conversion mode, the DS1631A
begins performing continuous conversions immediately at power-up, and the DS1631 and DS1731 begin
continuous conversions after a Start Convert T command is issued. For all three devices, consecutive
conversions continue to be performed until a Stop Convert T command is issued, at which time the device
goes into a low-power idle state. Continuous conversions can be restarted at any time using the Start
Convert T command.
In one-shot mode the DS1631A performs a single conversion at power-up, and the DS1631 and DS1731
perform a single temperature conversion when a Start Convert T command is issued. For all three
devices, when the conversion is complete the device enters a low-power idle state and remains in that
state until a single temperature conversion is again initiated by a Start Convert T command.
The resolution of the output digital temperature data is user-configurable to 9, 10, 11, or 12 bits,
corresponding to temperature increments of 0.5LC, 0.25LC, 0.125LC, and 0.0625LC, respectively. The
default resolution at power-up is 12 bits, and it can be changed through the R0 and R1 bits in the
configuration register. Note that the conversion time doubles for each additional bit of resolution.
After each conversion, the digital temperature is stored as a 16-bit two’s complement number in the two-
byte temperature register as shown in Figure 4. The sign bit (S) indicates if the temperature is positive or
negative: for positive numbers S = 0 and for negative numbers S = 1. The Read Temperature command
6 of 14
DS1631/DS1631A/DS1731
provides user access to the temperature register. Bits 3 through 0 of the temperature register are
hardwired to 0. When the device is configured for 12-bit resolution, the 12 MSbs (bits 15 through 4) of
the temperature register contain temperature data. For 11-bit resolution, the 11 MSbs (bits 15 through 5)
of the temperature register contain data, and bit 4 is 0. Likewise, for 10-bit resolution, the 10 MSbs (bits
15 through 6) contain data, and for 9-bit the 9 MSbs (bits 15 through 7) contain data, and all unused LSbs
contain 0s. Table 4 gives examples of 12-bit resolution output data and the corresponding temperatures.
Figure 4. TEMPERATURE, TH, AND TL REGISTER FORMAT
bit 15
bit 14
26
bit 13
25
bit 12
24
bit 11
23
bit 10
22
bit 9
21
bit 8
20
S
MS Byte
LS Byte
bit 7
2-1
bit 6
2-2
bit 5
2-3
bit 4
2-4
bit 3
bit 2
bit 1
bit 0
0
0
0
0
Table 4. 12-BIT RESOLUTION TEMPERATURE/DATA RELATIONSHIP
TEMPERATURE
DIGITAL OUTPUT
DIGITAL OUTPUT
(BINARY)
(HEX)
(LC)
+125
+25.0625
+10.125
+0.5
0
-0.5
-10.125
-25.0625
-55
0111 1101 0000 0000
0001 1001 0001 0000
0000 1010 0010 0000
0000 0000 1000 0000
0000 0000 0000 0000
1111 1111 1000 0000
1111 0101 1110 0000
1110 0110 1111 0000
1100 1001 0000 0000
7D00h
1910h
0A20h
0080h
0000h
FF80h
F5E0h
E6F0h
C900h
OPERATION—THERMOSTAT FUNCTION
The thermostat output (TOUT) is updated after every temperature conversion, based on a comparison
between the measured digital temperature and user-defined upper and lower thermostat trip points. TOUT
remains at the updated value until the next conversion completes. When the measured temperature meets
or exceeds the value stored in the upper trip-point register (TH), TOUT becomes active and remains active
until the measured temperature falls below the value stored in the lower trip-point register (TL) (see
Figure 5). This allows the user to program any amount of hysteresis into the output response. The active
state of TOUT is user-programmable through the polarity bit (POL) in the configuration register.
The user-defined values in the TH and TL registers (see Figure 4) must be in two’s complement format
with the MSb (bit 15) containing the sign bit (S). The TH and TL resolution is determined by the R0 and
R1 bits in the configuration register (see Table 6), so the TH and TL resolution matches the output
temperature resolution. For example, for 10-bit resolution bits 5 through 0 of the TH and TL registers read
out as 0 (even if 1s are written to these bits), and the converted temperature is compared to the 10 MSbs
of TH and TL.
The TH and TL registers are stored in EEPROM; therefore, they are NV and can be programmed prior to
device installation. Writing to and reading from the TH and TL registers is achieved using the Access TH
7 of 14
DS1631/DS1631A/DS1731
and Access TL commands. When making changes to the TH and TL registers, conversions should first be
stopped using the Stop Convert T command if the device is in continuous conversion mode. Note that if
the thermostat function is not used, the TH and TL registers can be used as general-purpose NV memory.
Another thermostat feature is the temperature high and low flags (THF and TLF) in the configuration
register. These bits provide a record of whether the temperature has been greater than TH or less than TL
at anytime since the device was powered up. These bits power up as 0s, and if the temperature ever
exceeds the TH register value, the THF bit is set to 1, or if the temperature ever falls below the TL value,
the TLF bit is set to 1. Once THF and/or TLF has been set, it remains set until overwritten with a 0 by the
user or until the power is cycled.
DS1631A STAND-ALONE THERMOSTAT OPERATION
Since the DS1631A automatically begins taking temperature measurements at power-up, it can function
as a standalone thermostat (i.e., it can provide thermostatic operation without microcontroller
communication). For standalone operation, the NV TH and TL registers and the POL and 1SHOT bits in
the configuration register should be programmed to the desired values prior to installation. Since the
default conversion resolution at power-up is 12 bits (R1 = 1 and R0 = 1 in the configuration register), the
conversion resolution is always 12 bits during standalone thermostat operation.
Figure 5. THERMOSTAT OUTPUT OPERATION
POL = 1 (TOUT IS ACTIVE HIGH)
TOUT
LOGIC 1
LOGIC 0
TEMP
TL
TH
CONFIGURATION REGISTER
The configuration register allows the user to program various DS1631 options such as conversion
resolution, TOUT polarity, and operating mode. It also provides information to the user about conversion
status, EEPROM activity, and thermostat activity. The configuration register is arranged as shown in
Figure 6 and detailed descriptions of each bit are provided in Table 5. This register can be read from and
written to using the Access Config command. When writing to the configuration register, conversions
should first be stopped using the Stop Convert T command if the device is in continuous conversion
mode. Note that the POL and 1SHOT bits are stored in EEPROM so they can be programmed prior to
installation is desired. All other configuration register bits are SRAM and power up in the state shown in
Table 5.
Figure 6. CONFIGURATION REGISTER
MSb
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
LSb
DONE THF
*NV (EEPROM)
TLF
NVB
R1
R0
POL* 1SHOT*
8 of 14
DS1631/DS1631A/DS1731
Table 5. CONFIGURATION REGISTER BIT DESCRIPTIONS
BIT NAME
FUNCTIONAL DESCRIPTION
(USER ACCESS)
DONE—Temperature
Conversion Done
Power-up state = 1.
DONE = 0. Temperature conversion is in progress.
DONE = 1. Temperature conversion is complete.
Power-up state = 0.
(Read Only)
THF = 0. The measured temperature has not exceeded the value
stored in the TH register since power-up.
THF—Temperature High Flag
(Read/Write)
THF = 1. At some point since power-up the measured temperature
has been higher than the value stored in the TH register. THF remains
a 1 until it is overwritten with a 0 by the user, the power is cycled, or
a Software POR command is issued.
Power-up state = 0.
TLF = 0. The measured temperature has not been lower than the
value stored in the TL register since power-up.
TLF = 1. At some point since power-up the measured temperature
has been lower than the value stored in the TL register. TLF remains a
1 until it is overwritten with a 0 by the user, the power is cycled, or a
Software POR command is issued.
TLF—Temperature Low Flag
(Read/Write)
Power-up state = 0.
NVB—NV Memory Busy
(Read Only)
NVB = 1. A write to EEPROMmemory is in progress.
NVB = 0. NV memory is not busy.
R1—Resolution Bit 1
(Read/Write)
R0—Resolution Bit 0
(Read/Write)
Power-up state = 1.
Sets conversion, TH, and TL resolution (see Table 6).
Power-up state = 1.
Sets conversion, TH, and TL resolution (see Table 6).
Power-up state = last value written to this bit.
POL = 1. TOUT is active high.
POL*—TOUT Polarity
(Read/Write)
POL = 0. TOUT is active low.
Power-up state = last value written to this bit.
1SHOT = 1. One-Shot Mode. The Start Convert T command initiates
a single temperature conversion and then the device goes into a low-
power standby state.
1SHOT*—Conversion Mode
(Read/Write)
1SHOT = 0. Continuous Conversion Mode. The Start Convert T
command initiates continuous temperature conversions.
*Stored in EEPROM
Table 6. RESOLUTION CONFIGURATION
RESOLUTION CONVERSION TIME
R1
R0
(BIT)
9
(MAX)
93.75ms
187.5ms
375ms
0
0
1
1
0
1
0
1
10
11
12
750ms
9 of 14
DS1631/DS1631A/DS1731
2-WIRE SERIAL DATA BUS
The DS1631, DS1631A, and DS1731 communicate over a bidirectional 2-wire serial data bus that
consists of a serial clock (SCL) signal and serial data (SDA) signal. The DS1631, DS1631A, and DS1731
interface to the bus through their SCL input pins and open-drain SDA I/O pins.
The following terminology is used to describe 2-wire communication:
Master Device: Microprocessor/microcontroller that controls the slave devices on the bus. The master
device generates the SCL signal and START and STOP conditions.
Slave: All devices on the bus other than the master. The DS1631, DS1631A, and DS1731 always
function as slaves.
Bus Idle or Not Busy: Both SDA and SCL remain high. SDA is held high by a pullup resistor when the
bus is idle, and SCL must either be forced high by the master (if the SCL output is push-pull) or pulled
high by a pullup resistor (if the SCL output is open-drain).
Transmitter: A device (master or slave) that is sending data on the bus.
Receiver: A device (master or slave) that is receiving data from the bus.
START Condition: Signal generated by the master to indicate the beginning of a data transfer on the
bus. The master generates a START condition by pulling SDA from high to low while SCL is high (see
Figure 8). A “repeated” START is sometimes used at the end of a data transfer (instead of a STOP) to
indicate that the master will perform another operation.
STOP Condition: Signal generated by the master to indicate the end of a data transfer on the bus. The
master generates a STOP condition by transitioning SDA from low to high while SCL is high (see Figure
8). After the STOP is issued, the master releases the bus to its idle state.
Acknowledge (ACK): When a device is acting as a receiver, it must generate an acknowledge (ACK) on
the SDA line after receiving every byte of data. The receiving device performs an ACK by pulling the
SDA line low for an entire SCL period (see Figure 8). During the ACK clock cycle, the transmitting
device must release SDA. A variation on the ACK signal is the “not acknowledge” (NACK). When the
master device is acting as a receiver, it uses a NACK instead of an ACK after the last data byte to indicate
that it is finished receiving data. The master indicates a NACK by leaving the SDA line high during the
ACK clock cycle.
Slave Address: Every slave device on the bus has a unique 7-bit address that allows the master to access
that device. The 7-bit bus address is 1 0 0 1 A2 A1 A0, where A2, A1, and A0 are user-selectable through
the corresponding input pins. The three address pins allow up to eight DS1631s, DS1631As, or DS1731s
to be multidropped on the same bus.
Control Byte: The control byte is transmitted by the master and consists of the 7-bit slave address plus a
read/write (R/･W･) bit (see Figure 7). If the master is going to read data from the slave device then R/･W･ =
1, and if the master is going to write data to the slave device then R/･W･ = 0.
Command Byte: The command byte can be any of the command protocols described in the COMMAND
SET section of this data sheet.
Figure 7. CONTROL BYTE
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
1
0
0
1
A2
A1
A0
R/･W･
10 of 14
DS1631/DS1631A/DS1731
Figure 8. START, STOP, AND ACK SIGNALS
SDA
SCL
STOP
START
ACK (or NACK)
From Receiver
Condition
Condition
GENERAL 2-WIRE INFORMATION
C All data is transmitted MSb first over the 2-wire bus.
C One bit of data is transmitted on the 2-wire bus each SCL period.
C A pullup resistor is required on the SDA line and, when the bus is idle, both SDA and SCL must remain
in a logic-high state.
C All bus communication must be initiated with a START condition and terminated with a STOP
condition. During a START or STOP is the only time SDA is allowed to change states while SCL is
high. At all other times, changes on the SDA line can only occur when SCL is low: SDA must remain
stable when SCL is high.
C After every 8-bit (1-byte) transfer, the receiving device must answer with an ACK (or NACK), which
takes one SCL period. Therefore, nine clocks are required for every one-byte data transfer.
INITIATING 2-WIRE COMMUNICATION
To initiate 2-wire communication, the master generates a START followed by a control byte containing
the DS1631, DS1631A, or DS1731 slave address. The R/･W･ bit of the control byte must be a 0 (“write”)
since the master next writes a command byte. The DS1631/DS1631A/DS1731 responds with an ACK
after receiving the control byte. This must be followed by a command byte from the master, which
indicates what type of operation is to be performed. The DS1631/DS1631A/DS1731 again respond with
an ACK after receiving the command byte.
If the command byte is a Start Convert T or Stop Convert T command (see Figure 9a), the transaction is
finished, and the master must issue a STOP to signal the end of the communication sequence. If the
command byte indicates a write or read operation, additional actions must occur as explained in the
following sections.
2-WIRE WRITES
The master can write data to the DS1631/DS1631A/DS1731 by issuing an Access Config, Access TH, or
Access TL command following the control byte (see Figures 9b and 9d). Since the R/･W･ bit in the control
byte was a 0 (“write”), the DS1631/DS1631A/DS1731 are already prepared to receive data. Therefore,
after receiving an ACK in response to the command byte, the master device can immediately begin
transmitting data. When writing to the configuration register, the master must send one byte of data, and
when writing to the TH or TL registers the master must send two bytes of data. After receiving each data
byte, the DS1631/DS1631A/DS1731 respond with an ACK, and the transaction is finished with a STOP
from the master.
11 of 14
DS1631/DS1631A/DS1731
2-WIRE READS
The master can read data from the DS1631/DS1631A/DS1731 by issuing an Access Config, Access TH,
Access TL, or Read Temperature command following the control byte (see Figures 9c and 9e). After
receiving an ACK in response to the command, the master must generate a repeated START followed by
a control byte with the same slave address as the first control byte. However, this time the R/･W･ bit must
be a 1, which tells the DS1631/DS1631A/DS1731 that a “read” is being performed. After the
DS1631/DS1631A/DS1731 send an ACK in response to this control byte, it begins transmitting the
requested data on the next clock cycle. One byte of data will be transmitted when reading from the
configuration register after which the master must respond with a NACK followed by a STOP. For two-
byte reads (i.e., from the Temperature, TH, or TL register), the master must respond to the first data byte
with an ACK and to the second byte with a NACK followed by a STOP. If only the most significant byte
of data is needed, the master can issue a NACK followed by a STOP after reading the first data byte.
COMMAND SET
The DS1631/DS1631A/DS1731 command set is detailed below:
Start Convert T [ 51h ]
Initiates temperature conversions. If the part is in one-shot mode (1SHOT = 1), only one conversion is
performed. In continuous mode (1SHOT = 0), continuous temperature conversions are performed until a
Stop Convert T command is issued.
Stop Convert T [ 22h ]
Stops temperature conversions when the device is in continuous conversion mode (1SHOT = 0).
Read Temperature [ AAh ]
Reads last converted temperature value from the 2-byte temperature register.
Access TH [ A1h ]
Reads or writes the 2-byte TH register.
Access TL [ A2h ]
Reads or writes the 2-byte TL register.
Access Config [ ACh ]
Reads or writes the 1-byte configuration register.
Software POR [ 54h ]
Initiates a software power-on-reset (POR), which stops temperature conversions and resets all registers
and logic to their power-up states. The software POR allows the user to simulate cycling the power
without actually powering down the device.
12 of 14
DS1631/DS1631A/DS1731
Figure 9 (a, b, c, d, e). 2-WIRE INTERFACE TIMING
THERM = DS1631, DS1631A, or DS1731
13 of 14
DS1631/DS1631A/DS1731
OPERATION EXAMPLE
In this example, the master configures the DS1631/DS1631A/DS1731 (A1A2A3 = 000) for continuous
conversions and thermostatic function.
MASTER THERMETER*
DATA
(MSb first)
START
90h
COMMENTS
MODE
TX
MODE
RX
START condition from MASTER.
TX
RX
MASTER sends control byte with R/･W･ = 0.
Acknowledge bit from THERMOMETER.
MASTER sends Access Config command.
Acknowledge bit from THERMOMETER.
MASTER writes a data byte to the configuration register to
put the THERMOMETER in continuous conversion mode
and set the TOUT polarity to active high.
RX
TX
ACK
TX
RX
RX
TX
ACh
ACK
TX
RX
02h
RX
TX
TX
TX
RX
TX
RX
TX
RX
TX
RX
TX
TX
TX
RX
TX
RX
TX
RX
TX
RX
TX
TX
TX
RX
TX
RX
TX
TX
RX
RX
RX
TX
RX
TX
RX
TX
RX
TX
RX
RX
RX
TX
RX
TX
RX
TX
RX
TX
RX
RX
RX
TX
RX
TX
RX
ACK
STOP
START
90h
Acknowledge bit from THERMOMETER.
STOP condition from MASTER.
START condition from MASTER.
MASTER sends control byte with R/･W･ = 0.
Acknowledge bit from THERMOMETER.
MASTER sends Access TH command.
ACK
A1h
ACK
28h
Acknowledge bit from THERMOMETER.
MASTER sends most significant data byte for TH = +40°C.
Acknowledge bit from THERMOMETER.
MASTER sends least significant data byte for TH = +40°C.
Acknowledge bit from THERMOMETER.
STOP condition from MASTER.
ACK
00h
ACK
STOP
START
90h
START condition from MASTER.
MASTER sends control byte with R/･W･ = 0.
Acknowledge bit from THERMOMETER.
MASTER sends Access TL command.
ACK
A2h
ACK
0Ah
Acknowledge bit from THERMOMETER.
MASTER sends most significant data byte for TL = +10°C.
Acknowledge bit from THERMOMETER.
MASTER sends least significant data byte for TL = +10°C.
Acknowledge bit from THERMOMETER.
STOP condition from MASTER.
ACK
00h
ACK
STOP
START
90h
START condition from MASTER.
MASTER sends control byte with R/･W･ = 0.
Acknowledge bit from THERMOMETER.
MASTER sends Start Convert T command.
Acknowledge bit from THERMOMETER.
STOP condition from MASTER.
ACK
51h
ACK
STOP
*THERMOMETER = DS1631, DS1631A, or DS1731
14 of 14
相关型号：
DS1631AU+T&R
Serial Switch/Digital Sensor, 12 Bit(s), 0.50Cel, Square, 8 Pin, Surface Mount, LEAD FREE, USOP-8
MAXIM
DS1631H
FLEXIBLE PERIPHERAL DRIVER for interfacing with CMOS circuits Dual Peripheral Driver
ROCHESTER
DS1631H883B
FLEXIBLE PERIPHERAL DRIVER for interfacing with CMOS circuits Dual Peripheral Driver
ROCHESTER
©2020 ICPDF网 联系我们和版权申明