BNC-R-CF [DDK]
RF BNC Connector, 1 Contact(s), Locking, Jack;
| 型号： | BNC-R-CF |
| 厂家： | 
DDK LTD. |
| 描述： | RF BNC Connector, 1 Contact(s), Locking, Jack |
| 文件： | 总15页 (文件大小：423K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
BNC Style Connector
BNC Series
OUTLINE
DDK’s 50 ohm BNC bayonet RF connector are
available in several configurations to support
a variety of design alternatives. These BNC
connectors are available in straight, right angle and
panel mount configurations.
Frequency
Range
DC to 2GHz
Characteristic
Impedance
FEATURE
50 Ω
・BNC style 50 ohm RF connector
･50 ohm impedance design
･Quick mate/demate with reliable bayonet coupling
Lock Type
Bayonet
･High reliability interconnect for numerous connect and disconnect cycles.
･BNC 50 ohm connector is intermateable with BNC75 (75 ohm) style connector.
・BNC is capable of mating with 75 ohm cable for frequencies less than 200MHz.
・Frequencies higher than 200MHz should use DDK’s BNC75 series connector.
CONFORMING STANDARD
IS-C-5412,ꢀMIL-PRF-39012,ꢀDSP-C-6202
J
SPECIFICATIONS
Characteristic Impedance
Rated Voltage
50 Ω
500VAC(r.m.s.)
Dielectric Withstanding Voltage 1500V AC(r.m.s.) for 1 minute
Insulation Resistance
Contact Resistance
V.S.W.R.
1000M Ω Mim. at 500V DC
3m Ω Max.
1.3 max. at DC to 2GHz
-55 〜 +85℃
Operating Temperature
＊ The specifications are typical but may not apply to all connectors.
And if the cable is not 50 Ω , the specification will be changed.
Please check the specifications on each item with its drawing from us when you use.
RRooHHSS
MATERIAL/FINISH
CCoommpplliiaanntt
Item
Material / Finish
Shell (Body)
Contact (Male)
Copper Alloy / Ni or Ag Plating
Copper Alloy / Ag or Au Plating
Contact (Female) Copper Alloy / Ag or Au Plating
Insulator
Gasket
PTFE
Silicon Rubber
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
ꢀMoreover, the characteristic and the specification of the published product are the reference values.
ꢀPlease confirm the content with the latest delivery specifications when you use the product.
141119
http://www.ddknet.co.jp
BNCꢀSeries
Unit：mm
○Sraight Cable Plug
Clamp Type
Finish
Center
Conductor Conductor
Applicable
Cable
Assembly
Part Number
φA（L）
6.4 25.0
6.4 25.0
6.4 25.0
5.4 27.0
5.4 27.0
Outer
Instruction
3D-2V
3C-2V
BNC-P-3-CF
Ag
Ni
Ag
Ag
Au
Ag
Ag
1
1
1
1
1
3D-2V
BNC-P-3-Ni-CF
3C-2V
（L）
3D-2V
BNC-P-3-NiCAu-CF
BNC-P-58U-CF
Ni
3C-2V
RG-55/U
RG-58/U
RG-55/U
RG-58/U
RG-62/U
RG-62/U
RG-59/U
RG-62/U
RG-59/U
RG-62/U
Ag
Ni
BNC-P-58U-Ni-CF
BNC-P-62U ー CF
BNC-P-62U-Ni-CF
6.6 26.2
6.6 26,2
Ag
Ni
Ag
Ag
1
1
UG-260/U-CF
6.55 24.6
6.55 24.6
Ag
Ni
Ag
Ag
1
1
UG-260/U-Ni-CF
Finish
Center
Applicable
Cable
Assembly
Part Number
φA （L）
7.1 29.1
7.1 29.1
Outer
Instruction
Conductor Conducto
r
3D-2W
3C-2W
3D-2W
3C-2W
BNC-P-3W-CF
Ag
Ni
Ag
Ag
1
1
BNC-P-3W-Ni-1-CF
（L）
Finish
Center
Conductor Conductor
Applicable
Cable
Assembly
Instruction
Part Number
φA （L）
Outer
5D-2V
5C-2V
5D-2V
5C-2V
5D-2W
5C-2W
5D-2W
5C-2W
BNC-P-5-CF
8.6 37.0
8.6 37.0
9.2 37.0
9.2 37.0
Ag
Ni
Ag
Ag
Ag
Ag
1
1
1
1
（L）
BNC-P-5-Ni-CF
BNC-P-5W-CF
BNC-P-5W-Ni-CF
Ag
Ni
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
ꢀMoreover, the characteristic and the specification of the published product are the reference values.
ꢀPlease confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
2
BNCꢀSeries
Unit：mm
○Straight Cable Plug
Finish
Center
ConductorConductor
Crimp Type
Applicable
Cable
Assembly
Instruction
Part Number
φA
Crimp Tool
Outer
1.5D-2V
1.5C-2V
BNC-P-1.5V-CR-CF
5.5
5.5
5.5
5.5
5.5
5.5
Ag
Ni
Ag
Ag
Au
Ag
Ag
Au
3
3
3
3
3
3
CR-H-1100
CR-H-1100
CR-H-1100
CR-H-1100
CR-H-1100
CR-H-1100
1.5D-2V
BNC-P-1.5V-CR-Ni-CF
BNC-P-1.5V-CR-NiCAu-CF
BNC-P-2.5V-CR-CF
1.5C-2V
（31.7）
1.5D-2V
1.5C-2V
2.5D-2V
2.5C-2V
2.5D-2V
2.5C-2V
2.5D-2V
2.5C-2V
RG-179/U
RG-179/U
Ni
Ag
Ni
BNC-P-2.5V-CR-Ni-CF
BNC-P-2.5V-CR-NiCAu-CF
Ni
BNC-P-179U-CR-CF
5.5
5.5
Ag
Ni
Ag
Ag
3
3
CR-H-1100
CR-H-1100
BNC-P-179U-CR-Ni-CF
Finish
Applicable
Cable
Assembly
Crimp
Part Number
Note
φA （L）Outer
Center
Instruction
Tool
Conductor Conductor
BNC-P-1.5CQEW-CR10-CF
BNC-P-1.5D-CR10-CF
1.5C-QEW
1.5D-XV
1.5D-QEW
3C-2V
5.5
4.0
24.3
23.3
Ni
Ni
Au
Au
ー
CR-H-1100
Delta-mate
（L）
4
CR-H-1120A Delta-mate
BNC-P-3C-CR10-BOOT-CF
BNC-P-3D-CR10-BOOT-CF
7.1
7.1
24.3
24.3
Ni
Ni
Au
Au
4
4
CR-H-1116
CR-H-1116
Delta-mate
Delta-mate
3D-2V
RG-58/U
RG-58A/U
3D-2V
BNC-P-58U-CR10-CF
BNC-P-3D-CR10-CF
6.3
7.1
24.3
24.3
Ni
Ni
Au
Au
4
4
CR-H-1115
CR-H-1116
Delta-mate
Delta-mate
Finish
Applicable
Cable
Assembly
Instruction
Crimp
Tool
Part Number
φA （L）Outer
Center
Conductor Conductor
BNC-P-3C-CR1-CF
3C-2V
3C-2V
7.0 28.0
7.0 28.0
Ag
Ni
Ag
Ag
2
2
CR-H-1102
CR-H-1102
BNC-P-3C-CR1-Ni-CF
（L）
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
ꢀMoreover, the characteristic and the specification of the published product are the reference values.
ꢀPlease confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
3
BNCꢀSeries
Unit：mm
○ Right Angle Cable Plug
Finish
Center
ConductorConductor
Applicable
Cable
Assembly
Instruction
Clamp Type
Part Number
φA
Outer
3D-2V
3C-2V
BNC-LP-3-CF
6.4
6.4
Ag
Ag
Ni
Ag
Au
Au
Ag
Ag
Ag
Ag
5
5
5
5
6
6
6
3D-2V
BNC-LP-3-CAu-CF
BNC-LP-3-NiCAu-CF
BNC-LP-3-Ni-CF
3C-2V
3D-2V
6.4
φA
3C-2V
3D-2V
（33）
6.4
Ni
3C-2V
RG-55/U
RG-58/U
RG-55/U
RG-58/U
RG-55/U
RG-58/U
BNC-LP-58U-CF
BNC-LP-58U-Ni-CF
BNC-LP-55U-CF
5.38
5.38
5.4
Ag
Ni
Ag
Finish
Center
Conductor Conductor
Applicable
Cable
Assembly
Part Number
Outer
Instruction
5D-2V
5C-2V
5D-2V
5C-2V
BNC-LP-5-CF
Ag
Ni
Ag
7
7
BNC-LP-5-Ni-CF
Au
（33）
○Straight Cable Jack
Clamp Type
Finish
Center
Applicable
Cable
Assembly
Instruction
Part Number
φA (L)
Outer
Conductor Conductor
3D-2V
3C-2V
BNC-J-3-CF
6.4
6.4
5.4
28.5
28.5
28.6
Ag
Ni
Ag
Ag
Ag
1
1
1
3D-2V
（L）
BNC-J-3-Ni-CF
BNC-J-58U-CF
3C-2V
RG-55/U
RG-58/U
Ag
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
ꢀMoreover, the characteristic and the specification of the published product are the reference values.
ꢀPlease confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
4
BNCꢀSeries
Unit：mm
○Straight Panel Cable Jack
Clamp Type
Finish
Center
Conductor Conductor
Applicable
Cable
Assembly
Instruction
4-φB
Part Number
φA φB (L)
Outer
3D-2V
3C-2V
BNC-PJ-3-CF
6.4
6.4
5.4
5.4
5.4
3.0 28.5
3.0 28.5
3.0 28.5
3.0 28.5
3.0 28.5
Ag
Ni
Ag
Ag
Ag
Ag
Au
1
1
1
1
1
3D-2V
15.8
2.3
（L）
BNC-PJ-3-Ni-CF
12.7
+0.1
3C-2V
RG-55/U
RG-58/U
RG-55/U
RG-58/U
RG-55/U
RG-58/U
BNC-PJ-58U-CF
Ag
Ni
0
4-φ3.0
BNC-PJ-58U-Ni-CF
BNC-PJ-58U-NiCAu-CF
Ni
+0.1
0
φ11.5
±0.05
12.7
Panel Mounting Dimensions
○Receptacle Jack
+0.1
Finish
Center
Conductor Conductor
0
4-φ3.0
Part Number
φB
4-φB
Outer
BNC-R-CF
3.1
3.1
Ag
Ag
Ag
Ag
Ag
+0.1
0
BNC-R-Ni-CF
UG-290/U-CF
Ni
φ9.0
M2.6
Ag
Ni
12.7
2.3
15.8
26.3
UG-290/U-Ni-1-CF M2.6
□17.5
±0.05
12.7
Panel Mounting Dimensions
Finish
Center
Conductor Conductor
4-φ3.2
4-φ3.0
12.7
Part Number
Outer
BNC-LR-CF
Ag
Ag
BNC-LR-Ni-CF
Ni
Ag
φ9.0
12.7
23
Panel Mounting Dimensions
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
ꢀMoreover, the characteristic and the specification of the published product are the reference values.
ꢀPlease confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
5
BNCꢀSeries
Unit：mm
○Receptacle Jack
Finish
Part Number
Note
+0.1
Outer
Center
0
5-φ1.2
Conductor Conductor
Board lock is
Ag plating
BNC-R-PC-4-Ag-CF
BNC-R-PC-4-D1-CF
Ni
Ni
Ag
Au
Board lock is
Ag plating.
2.3
13.3
2.5
±0.05
5.08
+0.1
0
10.16
PCB Mounting Dimensions
Finish
Center
Conductor Conductor
10.16
Part Number
Note
+0.1
Outer
0
5-φ1.2
Board lock is
Ag plating
BNC-LR-PC-4-Ag-CF
Ni
Ag
Board lock is
Ag plating
BNC-LR-PC-4-NiCAu-CF
Ni
Au
2.5
19.1
±0.05
5.08
+0.1
0
10.16
PCB Mounting Dimensions
Finish
4-φ3.0
+0.1
0
4-φ3.0
Part Number
Outer
Center
Conductor Conductor
BNC-PR-CF
BNC-PR-Ni-CF
Ag
Ni
Ag
Ag
+0.1
0
φ9.0
2.3
（17.7）
（28.2）
12.7
□17.5
±0.05
12.7
Panel Mounting Dimensions
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
ꢀMoreover, the characteristic and the specification of the published product are the reference values.
ꢀPlease confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
6
BNCꢀSeries
Unit：mm
○Straight Bulkhead Cable Jack
ꢀHex Dia.12.7
Finish
Center
Conductor Cnductor
Part Number
BNC-RB2-CF
Outer
Ag
Ag
Ag
Au
+0.1
BNC-RB2-Ni-CF
Ni
1.5
0
φ11.3
12.6
BNC-RB2-NiCAu-CF
Ni
26.3
Panel Mounting Dimensions
Panel Thickness：1.2 〜 3.5
ꢀHex Dia.12.7
Finish
Center
Conductor Conductor
Part Number
Outer
UG-625/U-CF
Ag
Ag
1.5
12.6
26.3
UG-625/U-Ni-CF
Ni
Ag
+0.1
0
φ11.3
Panel Mounting Dimensions
Panel Thickness：1.2 〜 3.5
+0.1
Hex Dia.12.7
0
φ9.6
Finish
Center
Conductor Conductor
Part Number
Outer
UG-604/U-CF
Ag
Ag
1.0
13.7
UG-604/U-Ni-1-CF
Ni
Ag
+0.1
0
8.5
26.3
Panel Thickness：0.7 〜 2.4
Panel Mounting Dimensions
+0.1
Finish
Hex Dia.12.7
0
φ9.92
Part Number
Note
Outer
Center
Conductor Conductor
Independent
Waterproof
UG-657/U-CF
UG-657/U-Ni-CF
Ag
Ni
Ag
Ag
with Frange O-ring
ꢀIndependent ꢀꢀ
ꢀWaterproofꢀꢀ
with Frange O-ring
2.44
15.1
+0.1
0
33
8.5
Panel Thickness：2.2 〜 6.0
Panel Mounting Dimensions
Finish
Part Number
Outer
Center
ꢀHex Dia.12.7
Conductor Conductor
UG-1094/U-CF
Ag
Ag
UG-1094/U-D1-CF
Ni
Au
+0.1
1.2
11.9
27
0
φ9.6
Panel Mounting Dimensions
Panel Thickness：2.2 〜 3.1
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
ꢀMoreover, the characteristic and the specification of the published product are the reference values.
ꢀPlease confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
7
BNCꢀSeries
Unit：mm
○Straight Bulkhead Cable Jack
Finish
Center
Conductor Conductor
+0.1
Part Number
Note
0
φ9.6
Outer
ꢀHex Dia.12.7
Independent
Waterproof
BNC-RBP1-CF
Ag
Ag
with Frange O-ring
Independent
2.5
BNC-RBP1-Ni-CF
Ni
Ag
Waterproof
+0.1
0
with Frange O-ring
15.2
8.5
32.6
Panel Mounting Dimensions
Panel Thickness：2.6〜6.4
+0.1
Finish
Center
Conductor Conductor
ꢀHex Dia.12.7
0
φ9.6
Part Number
Note
Outer
BNC-RB-CF
BNC-RB-Ni-CF
Ag
Ag
with Frange O-ring
with Frange O-ring
Ni
Ag
2.3
17.4
33
+0.1
0
8.5
Panel Mounting Dimensions
Panel Thickness：2.2〜7.0
○Dust Cap
Marking
ꢀJCW-159/U-CF/DDK
(17.8)
(20.5)
Part Number
BNC-CS-CF
Finish
Ag
Part Number
BNC-JC-CF
BNC-JC-Ni-CF
Finish
Short Cap
Short Cap
Ag
Ni
BNC-CS-Ni-CF
Ni
（φ3.5）
Part Number
BNC-RC-3
BNC-RC-3-D1
Finish
Ni
BNC style mating side
Marking：DDK
Ag
60±5
(75)
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
ꢀMoreover, the characteristic and the specification of the published product are the reference values.
ꢀPlease confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
8
BNCꢀSeries
Unit：mm
○Assembly Instruction（1）
Parts Configulration
MIL Clamp
Gasket
Gasket
Clamp
Nut
Washer
Clamp
Male Contact
Plug Body
Female Contact
Jack Body
Cut the cable as fig.1.
①
A
ꢀ Please be carefule to not damage the outer
conductor.
①
Applicable Cable
A
5D-2V, RG-59/U, RG-62/U 10mm
Washer
Nut
Gasket
Clamp
3D-2V, 5D-2W
15mm
RG-55/U, RG-58/U
3D-2W
12mm
②
③
Insert the nut, washer, gasket and clamp.
②
● The clamp is located on the outer conductor of the
ꢀ cable. Pick the outer conductor.
Cut the insulator and center conductor as fig.3.
③
ꢀFold up the outer conductor to the clamp equally and
cut the outer conductor of the cable along the clamp
as fig.3.
C
●Please be careful to not damage the center conductor.
B
Applicable Cable
B
C
3D-2V, 3D-2W,
RG-55/U, RG-58/U
5D-2V
6mm
3mm
Soldering
Contact
No Gap
7mm
5mm
④
⑤
RG-59/U, RG-62/U
5D-2W
5.5mm 3mm
7.2mm 5.4mm
Solder up the contact to the center conductor.
④
● Please be careful to not be swelled up the solder.
● Please be careful to not gap between contact and
insulator.
● Please be careful to not deform the insulator by
soldering
Body
Cable assembly
Insert the body into the above cable assembly and
screw up the nut.
⑤
● Please screw up the nut by wrench tightly.
Applicable Cable Recommended Tightening Torque
Hex Dia：. ９．５
Dia：. ９．５
3D-2V, RG-55/U, RG-58/U
RG-59/U, RG-62/U, 3D-2W
5D-2V
117.6 〜 147N・cm(12 〜 15kgf・cm)
196N・cm(20kgf・cm)
441N・cm(45kgf・cm)
5D-2W
490 〜 686N・cm(50 〜 70kgf・cm)
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
ꢀMoreover, the characteristic and the specification of the published product are the reference values.
ꢀPlease confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
9
BNCꢀSeries
Unit：mm
○Assembly Instruction（2）
Parts Configulration
Boot
Ferule
Center Conductor
Body
Insert the boot, ferule into the cable and cut the
①
①
ꢀꢀcable as fig.1.
15mm
●ꢀPlease be careful to not damage the outer
ꢀꢀconductor.
Cut the insulator and outer conductor as fig.2.
②
②
ꢀꢀPre-solder the center conductor and cut as fig.2.
●ꢀWhen cutting the insulator, please be careful to not
ꢀꢀdamage the center conductor.
13.3mm
10.6mm
6.6mm
Solder up the contact to the center conductor.
③
ꢀ Spread the end of the outer conductor to insert the
body between insulator and outer conductor easily.
ꢀ Please do not pick the outer conductor.
● Please be caredule to not be swelled up the solder.
Shave the excessed solder along the outside of the
contact.
③
④
● Please be careful to not deform the insulator by
soldering.
Insert the body into the cable between insulator and
outer conductor until the top of the contact is on the
same plane with the top of the body and move the
④
A
ferule to the body. Crimp the ferule at position
Edge of Crimp Dies
Edge of Body
B
and position
.
0.5～1.0mm
A
B
⑤
.
⑤ Cover the boot on the ferule
Boot
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
ꢀMoreover, the characteristic and the specification of the published product are the reference values.
ꢀPlease confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
10
BNCꢀSeries
Unit：mm
○Assembly Instruction（3）
Parts Configulration
（for 2.5D-2V）
(for 1.5D-2V / RG-179B/U)
Ferule
Contact Assembly
Plug Body
①
Cut the cable as fig.1.
①
20mm
● Please be careful to not damage the outer conductor.
Insert the ferule.
②
②
● In case of 2.5D-2V cable, insert the ferule into the cable
and push the ferule between sheath and outer conductor
until the head of ferule is reached to the sheath by
inserting tool(E3001-160) and pick the outer conductor.
● In case of 1.5D-2V or RG-179B/U cable , insert the
ferule until the ferule reached at the sheath and pick the
outer conductor.
Inserting Tool
Ferule
2.5D-2V
Ferule
1.5D-2V,RG-179B/U
Folding down the outer conductor to the ferule and
cut the couter conductor along the ferule as fig.3.
Cut the insulator and center conductor and pre-solder
the center conductor.
③
A
17mm
10mm
③
④
Applicable Cable
2.5D-2V
1.5-2V, RG-179B/U
A
4mm
5mm
Soldering
Insert the contact assembly into the above cable
assembly. Solder up the contact with center conductor
and crimp the root of the contact assembly.
④
1mm
crimping
Insert the body into the above cable assembly and
screw up the body by the wrench tightly.
⑤
⑤
Recommended Tightening Torque
: 196 N･cm(20kgf･cm)
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
ꢀMoreover, the characteristic and the specification of the published product are the reference values.
ꢀPlease confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
11
BNCꢀSeries
Unit：mm
○ Assembly Instruction（4）
Parts Configulration
Insulator
Bayonet
Delta-mate Outer Conductor
Body
Crimp
Crimp area
*Insulator
Ferule
Sleeve
Contact
(24.3)
BNC-P mating side
*The insulator is attached with BNC-P-1.5D-CR10-CF.
Please cover the sheath when crimping the contact.
①
(24.3)
(24.3)
Cut the cable as fig.1.
①
ꢀꢀL Amm=Lmm-12mm
L
Cable
Remove the sheath
②
●ꢀPlease be careful to not damage the outer
ꢀꢀconductor.
LA
②
③
15
Insert the ferule and spread the tip of the outer
③
ꢀconductor.
Plunge the sleeve by stripper without
Assembly Tool
Attachment
89134
ꢀdiging the edge.
CR-H-1115
CR-H-1116
CR-H-1120A
89141
Sleeve
Ferule
Cut the center conductor by stripper as fig.4.
④
⑤
Cut the insulator by stripper as fig.5.
Insert the stripper and dig the edge to the
insulator. Rotate the stripper a few times and pull
B
⑤
B
C
④
⑥
Stripper
ꢀ off the insulator.
A
D
Trim the extra outer conductor along the sleeve.
⑥
⑦
Put the contact into the crimp tool attachment and
insert it into the crimp dies as fig.7. Insert the
center conductor into the contact hole and crimp
the contact with touching the contact brim to the
end of sheath.
⑦
⑧
⑨
Insert the above contact assembly into the body
until the top of contact is same plane as rim
of outer conductor.
⑧
● After the contact brim is inserted into the body,
do not rotate the cable and body.
dies
⑨
Put the above cable assembly in the crimp tool and
crimp the root of the body.
⑨
● Please match the hex of dies with the hole of the
body.
for CR-H-1120A
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
ꢀMoreover, the characteristic and the specification of the published product are the reference values.
ꢀPlease confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
12
BNCꢀSeries
Unit：mm
○Assembly Instruction（5）
Nut2
Parts Configulration
Nut1
Washer
Clamp
Gasket
Body Assembly
Cable
Cable length require for the single ended cable assembly
ꢀꢀL =L +0.3
1
L1
Outer Conductor
Center Conductor
（Pre-soldering）
Washer
Sheath
1-1.Cut the cable as fig.1.
①
②
1-2. Pre-sollder the center conductor.
Note）Please be careful to not damage the outer
conductor.
±0.3
2
±0.3
1-3．Insert the nut 1, washer and gasket.
8
Nut1
Gasket
Clamp
Sheath
2-1.Insert the clamp into the outer conductor and
put it on the sheath.
Insulator
2-2. Pick the outer conductor and fold down to the
clamp and cut the extra outer conductor along
the clamp.
Outer conductor
Cut the outer conductor
along the clamp
③
Nut1
3-1.Insert the above cable assembly into the body.
3-2.Screw up the nut1 to the body.
Recommended screw toque：117.6 〜 147N・㎝
ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ（12 〜 15kgf・㎝）
Cable Assembly
□12.7
9.5
（Hex Dia.）
Body Assembly
Nut2
④
4-1.Solder up the contact with the center
conductor
4-2.Screw up the nut2 to the body.
Recommended screw torque：49N・㎝
（5kgf・㎝）
Soldering
Center Conductor
Contact
Body Assembly
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
ꢀMoreover, the characteristic and the specification of the published product are the reference values.
ꢀPlease confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
13
BNCꢀSeries
Unit：mm
○Assembly Instruction(6）
Parts Configulration
Nut1
Washer
Gasket
Clamp
Body Assembly
Nut2
The cable length require for the single ended cable
assembly.ꢀꢀ
ꢀꢀL =L+3.3
1
Cable
L
①
②
1-1.Insert the nut1, washer and gasket.
1-2. Cut the cable as fig.1.
Note）Please be careful to not damage the outer
conductor.
Nut1
Washer
Gasket
Outer Conductor
11
Cable
2-1.Insert the clamp into the outer conductor and
move to the sheath.
2-2.Pick the outer conductor equally. Fold down to
the clamp and cut the extra outer conductor
along the clamp.
3-3.Cut the insulator as fig. 2.
2-4.Pre-solder the center conductor and cut the
center conductor as fig.2.
Insulator
Clamp
Center Conductor
(Pre-soldering)
±0.3
2
±0.3
(3)
5
Cut the outer conductor
along the clamp
Contact Slit
③
3-1.Insert the above contact assembly into the
body assembly.
Note）The center conductor is located in the
center of contact slit.
Cable Assembly
□12.7
3-2.Move the nut1, washer and gasket to the body.
3-2.Screw up the nut1 to the body.
Recommended screw torque：117.6 〜 147N・㎝
9.52
(Hex Dia.)
ꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀꢀ（12 〜 15kgf・㎝）
Body Assembly
④
⑤
Soldering
4-1.Solder up the contact with center conductor.
Nut2
5-1.Screw up the nut2 to the body.
Recommended screw torque：49N・㎝ min.
ꢀ
（5kgf・㎝ min.）
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
ꢀMoreover, the characteristic and the specification of the published product are the reference values.
ꢀPlease confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
14
BNCꢀSeries
Unit：mm
○Assembly Instruction（7）
Parts Configulration
Nut２
Washer２
Body Assembly
Nut１
Washer１
Clamp
The cable length require for the single ended
cable assembly：L
1
ꢀꢀꢀL =L+3
1
Ｌ
Sheath
Outer Conductor
①
1-1.Cut the cable as fig.1.
Note）Please be careful to not damage the outer
conductor.
±0.5
15
Cable
2-1.Insert the nut1, washer1 and insert the clamp
on the outer conductor and move to the
sheath.
Clamp
Washer１
Outer Conductor
Nut１
②
2-2. Fold down to the clamp and cut the extra
outer conductor in 3 mm from the clamp.
2-3.Move the washer 1 and nut 1 to the clamp.
3
Washer２
Insulator
Outer Conductor
③
（Pre-soldering）
3-1.Insert washer 2 on the outer conductor and cut
the insulator as fig.3.
3-2. Pre-solder the center conductor and cut the
center conductor as fig.3.
+0.5
0
0
-0.5
4
5.7
Contact Slit
④
⑤
4-1.Insert the above cable assembly into the
bodyassembly and screw up the nut 1.
Recommended screw torque：196N・㎝（20kgf・㎝）
Note）The center conductor is located in the
Body Assembly
center of contact slit.
Nut２
Soldering
5-1.Solder up the contact with center conductor.
5-2.Screw up the nut 2 to the body.
Recommended screw torque：49N・㎝（5kgf・㎝）
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
ꢀMoreover, the characteristic and the specification of the published product are the reference values.
ꢀPlease confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
15
相关型号：
BNC-R-PC(40)
RF BNC Connector, 1 Contact(s), Female, Board Mount, Solder Terminal, Locking, Plug, ROHS COMPLIANT
HRS
©2020 ICPDF网 联系我们和版权申明