TNC-J-2.5D2W-CR10-CF [DDK]
TNC Style Connector;
| 型号： | TNC-J-2.5D2W-CR10-CF |
| 厂家： | 
DDK LTD. |
| 描述： | TNC Style Connector |
| 文件： | 总15页 (文件大小：447K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
TNC Style Connector
TNC Series
FEATURE
・TNC series is a thread coupling coaxial
connector which is modified BNC style
connector.
Characteristic
Impedance
50 Ω
・Due to the thread coupling, it is superior to
BNC style connector in vibration load.
・Other electrical and mechanical characteristics
are same as BNC style connector.
・Recommended toque of coupling is
45 〜 68.6N・cm.
Frequency
Range
DC to 2GHz
Lock Type
Screw
CONFORMING STANDARD
MIL-PRF-39012
SPECIFICATIONS
Characteristic Impedance
Rated Voltage
50 Ω
500VAC(r.m.s.)
Dielectric Withstanding Voltage 500V AC(r.m.s) / 1 minute
Insulation Resistance
Contact Resistance
V.S.W.R.
1,000M Ω min. at 500V DC
3m Ω max.
1.3 max. (DC 〜 2GHz)
-55 〜 +85℃
Operating Temperature
＊ The specifications are typical but may not apply to all
connectors. Please check the specifications on each item with
its drawing from us when you use.
RRooHHSS
MATERIAL/FINISH
CCoommpplliiaanntt
Item
Shell
Contact (Female)
Contact (Male)
Insulator
Material / Finish
Copper Alloy / Ni or Ag Plating
Copper Alloy / Ag or Au Plating
Copper Alloy /Ag or Au Plating
PTFE
Gasket
Silicon Rubber
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
ꢀMoreover, the characteristic and the specification of the published product are the reference values.
ꢀPlease confirm the content with the latest delivery specifications when you use the product.
150424
http://www.ddknet.co.jp
TNCꢀSeries
Unit：mm
○Straight Cable Plug
Clamp Type
Finish
Center
ConductorConductor
Assembly
Part Number
Applicable Cable
Outer
L
Instruction
3D-2V
TNC-P-3-CF
25.0
Ag Ag
6
3D-QEV
L
Crimp Type
Finish
Center
ConductorConductor
Assembly
Crimp
Tool
Part Number
Applicable Cable
φA
Outer
L
Instruction
1.5D-2W
1.5D-QEW
2.5D-2W
TNC-P-1.5DQEW-CF
TNC-P-2.5D2W-CR10-CF
TNC-P-3D2W-CR10-CF
5.5 22.3
6.3 24.3
7.9 24.3
Ni
Ni
Ni
Au
Ag
Ag
1
2
2
CR-H-1100
CR-H-1115
CR-H-1135
L
2.5D-QEW
3D-2W
3D-QEW
Finish
Center
ConductorConductor
Ni Au
Assembly
Outer
Part Number
Applicable Cable
2D-FB
Crimp Tool
φA
L
Instruction
TNC-P-2DFB-1-CF
6.2 29.7
3
CR-H-1105
L
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
ꢀMoreover, the characteristic and the specification of the published product are the reference values.
ꢀPlease confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
2
TNCꢀSeries
Unit：mm
○Straight Cable Jack
Crimp Type
Finish
Center
Conductor Conductor
Applicable
Cable
Assembly
Outer
Part Number
Crimp Tool
φA φB
L
Instruction
TNC-J-1.5DXW-CR10-120-CF
TNC-J-2.5D2W-CR10-CF
2D-FB
5.5 12.0 26.8
Ni
Ag
4
CR-H-1142
CR-H-1105
2.5D-2W
2.5D-QEW
6.25 14.6 25.0
Ni
Ag
4
L
Finish
Center
Conductor Conductor
Assembly
Applicable
Cable
Outer
Part Number
Crimp Tool
CR-H-1135
φA φB
L
Instruction
3D-2W
TNC-J-3D2W-CR10-CF
7.9 14.6 25.42
Ni Ag
4
3D-QEW
5.0
17.0
L
○ Straight Bulkhead Cable Jack
Finish
Center
Conductor Conductor
Applicable
Cable
Assembly
Outer
Part Number
Crimp Tool
φA φB
L
Instruction
2.5D-2W
TNC-BJ-2.5D-QEW-CF
14.0 6.25 27.9
Ni Ag
4
CR-H-1105
2.5D-QEW
※ Mounting Panel Thickness：2.7mm max.
+0.1
13
φ11.2 0ꢀ
(Flat Diameter）
10.4+0.1
0
2
16.8
10.2
(Detent Diameter）
L
Panel Mounting Dimensions
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
ꢀMoreover, the characteristic and the specification of the published product are the reference values.
ꢀPlease confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
3
TNCꢀSeries
Unit：mm
○Straight Panel Cable Jack
Finish
Center
Conductor Conductor
Applicable
Cable
Assembly
Crimp Type
Outer
Part Number
Crimp Tool
Instruction
1.5D-QEW
1.5D-2W
TNC-PJ-1.5DQEW-CR10-CF
Ni
Ag
5
CR-H-1142
4-φ3.0
4-φ3.0
φ12.0
15.8
26.8
2.3
12.7
□17.5
12.7
Panel Mounting Dimensions
Finish
Applicable
Cable
Assembly
Outer
Center
Part Number
Crimp Tool
Instruction
Conductor Conductor
1.5D-XW
TNC-PJ-1.5DXW-CR10-M-CF
Ni Ag
7
CR-H-1100
1.5D-XWTA
+0.1
0
4-φ3.0
4-M2.5×0.45
+0.1
φ12.0 0
15.8
30.8
2.3
18.2
18.2±0.05
□25.4
Panel Mounting Dimensions
Finish
Applicable
Cable
Assembly
Outer
Center
Part Number
Crimp Tool
Instruction
Conductor Conductor
1.5D-QEV
1.5D-2V
TNC-PJ-2H-1.5D-CR10-CF
Ni
Ag
5
CR-H-1101
2-φ3.2
2-φ3.2
φ6.0
2.3
14.7
24.4
12
Panel Mounting Dimensions
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
ꢀMoreover, the characteristic and the specification of the published product are the reference values.
ꢀPlease confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
4
TNCꢀSeries
Unit：mm
○ Receptacle Jack
Finish
Outer
Center
Part Number
TNC-R-CF
Conductor
Conductor
Ag
Au
TNC-R-NiCAu-CF
Ni
Au
4-φ2.8±0.15
4-M2.6×0.45
φ11.1+0.2
0
2.3
15.8
26.3
12.7
12.7±0.05
□17.5
Panel Mounting Dimensions
Finish
Outer
Center
Part Number
TNC-R2-CF
Conductor
Conductor
Ag
Ag
TNC-R2-Ni-CF
Ni
Ni
Ag
Au
TNC-R2-NiCAu-CF
+0.1
4-φ3.0
4-φ3.00
φ11.1+0.2
0
2.3
15.8
26.3
12.7
□17.5
12.7±0.05
Panel Mounting Dimensions
Finish
Outer
Center
Part Number
TNC-R2-2H-Ni-CF
Conductor
Conductor
Ni
Ag
2-φ3.0
+0.1
φ9.00
2.3
15.8
2-φ3+00.1
11
26.3
Panel Mounting Dimensions
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
ꢀMoreover, the characteristic and the specification of the published product are the reference values.
ꢀPlease confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
5
TNCꢀSeries
Unit：mm
○Receptacle Jack
Finish
Outer
Center
Part Number
TNC-SR-3-CF
Conductor
Conductor
Ni
Au
+0.1
4-φ3.00
4-φ3.0
φ12+0.1
0
4
2.3
9.6
15.8
12.7
□17.5
12.7±0.05
27.7
Panel Mounting Dimensions
Finish
Outer
Center
Part Number
TNC-SR-6-CF
Conductor
Conductor
Ni
Au
+0.1
4-φ3.10
4-φ3.0
(Thru-Hole）
+0.1
0
φ4.1
2
6.8
2
17.8
12.7±0.05
12.7
26.6
□17.5
Panel Mounting Dimensions
Finish
Outer
Center
Part Number
TNC-SR-9-CF
Conductor
Conductor
Ni
Au
4-φ3.0
+0.1
4-φ3.10
(Thru-Hole）
+0.1
0
φ4.1
12.7
2
□17.5
8.5
2
17.8
12.7±0.05
26.6
Panel Mounting Dimensions
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
ꢀMoreover, the characteristic and the specification of the published product are the reference values.
ꢀPlease confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
6
TNCꢀSeries
Unit：mm
○Receptacle Plug
Finish
Outer
Center
Part Number
Conductor
Conductor
TNC-PR-CF
4-φ3.0
Ag
Ag
+0.1
4-φ3.20
+0.1
φ9.00
18.0
28.5
2.3
12.7
□17.5
12.7±0.05
Panel Mounting Dimensions
○Right Angle Receptacle Jack
Finish
Outer
Center
Part Number
Conductor
Conductor
TNC-LR-CF
TNC-LR-Ni-CF
Ag
Au
Ni
Ag
4-φ3+0.1
23
0
12.7
14.3
2.3
+0.1
φ9.00
4-φ3.0
12.7±0.05
Panel Mounting Dimensions
Finish
Outer
Center
Part Number
TNC-LR-1-CF
Conductor
Conductor
Ag
Ag
21.6
4-M2.6
5
14.3
2.3
12.7
□17.5
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
ꢀMoreover, the characteristic and the specification of the published product are the reference values.
ꢀPlease confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
7
TNCꢀSeries
Unit：mm
○ Dust Cap
7/16-28UNEF-2B
Part Number
TNC-RC-1
TNC-RC-1-D1
Finish
（φ3.5）
Ni
Ag
(60)
(75)
7/16-28UNEF-2B
Part Number
Finish
Ni
TNC-C-2-CF
TNC-C-2-D1-CF
Ag
15
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
ꢀMoreover, the characteristic and the specification of the published product are the reference values.
ꢀPlease confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
8
TNCꢀSeries
Unit：mm
○ Assembly Instruction（1）
Parts Configulration
Sleeve
Contact
Heat-shrinkable tube
Ferule
Insulator
Body
Cable length which require for the cable assembly.
Cable length
L=L1-3.3
L
L=L2+19.7
L2
L1
① Insert the heat-shrinkable tube onto the cable.
Cut the cable as fig.1.
①
Heat-shrinkable tube
Outer Conductor
Please be careful to not damage the outer conductor.
±0.5
14.7
Sheath
② Insert the ferule on the outer conductor and
spread the top of the outer conductor.
Insulator
Sleeve
②
③
Insert the sleeve between insulator and outer
conductor. And cut the outer conductor along the sleeve.
Ferule
Cut the insulator as fig. 3.
③
Insulator
ꢀꢀPlease be careful to not damage the center conductor.
ꢀꢀPre-solder the center conductor and cut the center
ꢀꢀconductor.
Outer Conductor
Center Conductor
(Pre-soldering)
ꢀPlease be careful to not damage the insulator by
ꢀsoldering. Insert the insulator as fig.3.
0
6.2-0.5
4+-00.3.2
Insulator
Soldering
④ Solder up the contact with center conductor.
No gap between insulator and contact.
④
No gap
Contact
⑤ Insert the body into the above cable assembly.
And crimp the root of the body.
Please be careful to meet the crimp height
as follows.
5.33～5.84
⑤
(between body and contact)
A
Measuring point
(3.1)
Dies Ａ
Note）Distance between body and contact must be met.
⑥
Cover the heat-shrinkable tube on the root of the body
and heat up.
⑥
Heat-shrinkable tube
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
ꢀMoreover, the characteristic and the specification of the published product are the reference values.
ꢀPlease confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
9
TNCꢀSeries
Unit：mm
○ Assembly Instruction（2）
Parts Configulration
Boot
Contact
Ferule
Sleeve
Body
① Insert the boot into the cable and
cut the cable as fig.1.
14
Boot
①
②
Cable
ꢀPlease be careful to not damage the outer conductor.
Outer Con
Sheath
Ferule
② Insert the ferule on the outer conductor and
spread the top of the outer conductor. Press-in rhe
sleeve between insulator and outer conductor.
ꢀ Cut the extra outer conductor along the sleeve.
Sleeve
Outer Conductor
Center Conductor
③ Cut the insulator and center conductor as fig.3.
③
④
Part Number
TNC-P-2.5D2W-CR10-CF
TNC-P-3D2W-CR10-CF
A
B
A
B
5.0mm
5.5mm
4.0mm
3.5mm
Crimp Tool
④ Pinch the contact in the crimping hole(center
and insert the center conductor of the cable.
hole)
Crimp the contact (match the side hole of contact
with the curve of crimping hole of tool.)
Insulator
Center Conductor
Contact
Part Number
TNC-P-2.5D2W-CR10-CF
TNC-P-3D2W-CR10-CF
Crimp Tool
CR-H-1115
CR-H-1135
No gap
Crimping Dies
Contact crimped
⑤ Insert the above contact into the body.ꢀMatch the
ꢀ key in the insulator and keyway of the contact.
Crimp the root of body as fig.5. Cover the boot on the
root of the connector body.
Tool Surface
Body Surface
Crimp Tool
Body
⑤
Boot
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
ꢀMoreover, the characteristic and the specification of the published product are the reference values.
ꢀPlease confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
10
TNCꢀSeries
Unit：mm
○Assembly Instruction（3）
Parts Configulration
Sleeve
Boot
Contact assembly
Body
① Insert the boot and sleeve into the cable and
cut the cable as fig.1. Please be careful to not
damage the outer conductor.
①
Boot
Sleeve
19
Outer Conductor
Sheath
Cable
10
4
7
4
②
③
② Cut the cable as fig.2. Cut the center conductor
after pre-soldering.
Insulator
Outer Conductor
Aluminum foil tape
Cente Conductor
（Cut off afterpre-soldering)
③ Insert the contact between outer conductor and
aluminum foil tape. Solder the contact with
center conductor.
Soldering
When the solder is stick out, please shave
the extra solder along the contact.
Contact assembly
1
④ Cover the sleeve on the outer conductor and
④
⑤
Crimp Tool : (CR-H-1105)
crimp as fig.4.
Sleeve
Boot
⑤ Insert the above contact into the body and
screw. Cover the boot on the root of the body.
Body
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
ꢀMoreover, the characteristic and the specification of the published product are the reference values.
ꢀPlease confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
11
TNCꢀSeries
Unit：mm
○ Assembly Instruction（4）
Parts Configulration
Contact
Body
Heat-shrinkable tube
Ferule
Insulator
Sleeve
① Insert the heat-shrinkable tube into the cable
and cut the cable as fig.1. Please be careful to
not damage the outer conductor.
①
Heat-shrinkable tube
Sheath
Outer Conductor
A
Part Number
TNC-J-1.5DXW-CR10-120-CF
TNC-J-2.5D2W-CR10-CF
TNC-J-3D2W-CR10-CF
TNC-BJ-2.5DQEW-CF
A
13.0mm
11.0mm
11.5mm
13.0mm
Cable
Outer Conductor
②
Ferule
Sleeve
② Insert the ferule on the outer conductor and
spread the top of the outer conductor. Press in
the sleeve between outer conductor and
insulator.
Spread the top
Cut off the extra outer conductor along the sleeve.
Cut the cable as fig.3. Cut the center conductor
after pre-soldering. Please be careful to not damage
the center conductor.
③
③
④
⑤
Sleeve
Insulator
Center Conductor
（Pre-soldering）
Part Number
B
C
Outer Conductor
C
B
●
TNC-J-1.5DXW-CR10-120-CF
TNC-J-2.5D2W-CR10-CF
TNC-J-3D2W-CR10-CF
TNC-BJ-2.5DQEW-CF
5.7mm
3.0mm
3.1mm
6.0mm
2.8mm
2.5mm
2.5mm
2.0mm
Soldering
Contact
Insulator
Insert the insulator and solder the contact with center
④
conductor.
When the solder is stick out, please
No gap
shave the extra solder along the contact.
⑤ Insert the above contact into the body. Match the
ꢀ key in the insulator and keyway of the contact.
Crimp the root of body as fig.5.
Crimping Dies
same level
Part Number
TNC-J-1.5DXW-CR10-120-CF
TNC-J-2.5D2W-CR10-CF
TNC-J-3D2W-CR10-CF
TNC-BJ-2.5DQEW-CF
Tool
CR-H-1100
CR-H-1105
CR-H-1135
CR-H-1105
⑥
at-shrinkable tube
⑥ Cover the heat-shrinkable tube on the root of
the body and heat up.
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
ꢀMoreover, the characteristic and the specification of the published product are the reference values.
ꢀPlease confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
12
TNCꢀSeries
Unit：mm
○ Assembly Instruction（5）
Parts Configulration
Heat-shrinkable tube
Ferule
Contact
Body
Insulator
Sleeve
① Cut the cable as fig.1.
Please be careful to not damage the outer
conductor.
Sheath
Outer Conductor
①
②
Part Number
A
A
TNC-PJ-1.5DQEW-CR10-CF
TNC-PJ-2H-1.5D-CR10-CF
13.0mm
10.0mm
Ferule
Insulator
Spread the top
② Insert the ferule on the outer conductor and spread
the top of the outer conductor.
③ Insert the sleeve and cut the cable as fig.3.
ꢀPress in the sleeve between outer conductor and
insulator. Cut off the extra outer conductor along the
sleeve. Cut the insulator and center conductor as below
table. Cut the center conductor after pre-soldering.
Please be careful to not damage the center conductor.
Sleeve
Center Conductor
（Pre-soldering）
③
C
B
●
Cut the center conductor after pre-soldering
Part Number
B
C
TNC-PJ-1.5DQEW-CR10-CF
TNC-PJ-2H-1.5D-CR10-CF
5.7mm
4.0mm
3.0mm
3.0mm
④ Insert the insulator on the insulator of the cable
and solder the contact with center conductor.
When the solder is stick out, please
Soldering
Insulator
④
⑤
Contact
shave the extra solder along the contact.
No gap
⑤ Insert the above contact into the body. Match the
ꢀ key in the insulator and keyway of the contact.
Crimp the root of body as fig.5.
Body
same level
Part Number
TNC-PJ-1.5DQEW-CR10-CF
TNC-PJ-2H-1.5D-CR10-CF
Tool
CR-H1142
CR-H1101
Crimping Dies
⑥
⑥ Cover the heat-shrinkable tube on the root of
the body and heat up.
Heat-shrinkable tube
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
ꢀMoreover, the characteristic and the specification of the published product are the reference values.
ꢀPlease confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
13
TNCꢀSeries
Unit：mm
○ Assembly Instruction（6）
Parts Configulration
Washer
Contact
Nut
Gasket
Clamp
Body
3D-2V
① The cable length require for the cable assembly
L1=L-x
①
L1
L
② Insert nut, washer and gasket into the cable and
cut the cable as fig.2.
Sheath
Outer Conductor
②
③
Please be careful to not damage the outer conductor.
10
Nut
Washer
Gasket
③ Insert the clamp on the outer conductor and turn
down the outer conductor. Cut the outer
conductor along the clamp.
Pick the outer conductor
and turn down to the clamp
Insulator
ꢀCenter Conductor
（Pre-soldering）
Clamp
Cut the insulator as fig.3. Please be careful to not
damage the center conductor.
Cut the center conductor after pre-soldering.
Trim the outer conductor
along the clamp
0
3+0.5
-0.5
3
0
④ Insert the contact and solder the contact with
center conductor.
Contact
Soldering
Please bee careful to not damage the insulator by
heat.
④
⑤
No gap
Body
Insulator
Body assembly
⑤ Insert the above contact into the body.
Insert the the gasket and washer into the body and
screw the nut.
Recommended torque : 117.5 〜 147N・cm
ꢀꢀ
(12 〜 15Kgf・cm）
Flat Diameter：
9.5±0.2
Flat Diameter：9.5±0.2
0.21+-0.213
（Gap between body and contact）
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
ꢀMoreover, the characteristic and the specification of the published product are the reference values.
ꢀPlease confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
14
TNCꢀSeries
Unit：mm
○ Assembly Instruction（7）
Parts Configulration
Insulator
Contact
Body
Ferule
Heat-shrinkable tube
Cable length which require for the cable assembly.
ꢀL=L1-10.5
L1
①
Cable
Outer Conductor
Insert the heat-shrinkable tube into the cable.
①
ꢀCut the cable as fig.1.
15+1
0
ꢀ Note）Please be careful to not damage the outer conductor.
Sheath
Heat-shrinkable tube
②
③
Ferule
② Insert the ferule on the outer conductor
Pick and spread the outer conductor.
Pick and spread the top
Insulator
Center Conductor
Pre-soldering
and
③ Turn down the outer conductor to the ferule
cut the outer conductor as fig.3.
ꢀ Cut the insulator as fig. 3 and pre-solder the center
conductor. And cut the center conductor as fig.3.
ꢀ Note）Please be careful to not center conductor.
0
2.9-1
4±0.5
(9.7)
No gap
④
⑤
Soldering
Contact
cable, solder up the
④ Insert the insulator into the
contact with center conductor.
ꢀNote）When the solder is stick out, please shave the
extra solder along the contact.
Insulator
Interface Dimension
⑤ Insert the body into the above cable assembly and
crimp the root of the body.
±0.25
4.98
（between contact and washer
ꢀNote）When inserting the body, match the contact notch
with projection of insulator.
Dies：A
ꢀNote）Crimp the body with same level of body and dies.
ꢀNote）Meet the interface dimension and crimp heightꢀ
Cable assembly
Same level
Body
Body Surface
a
Measurering point
L/2
Crimp Height
L
ꢀａ，ｂ，ｃ（each sides）
＝
４．７６～５．００
on the root of the
⑥ Cover the heat-shrinkable tube
body and heat up.
Heat-shrinkable tube
⑥
◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice.
ꢀMoreover, the characteristic and the specification of the published product are the reference values.
ꢀPlease confirm the content with the latest delivery specifications when you use the product.
http://www.ddknet.co.jp
相关型号：
TNC-J-C-F-ST-BH1
RF TNC Connector, Female, Panel Mount, Cable Mount, Crimp Solder Terminal, Jack, ROHS COMPLIANT
SAMTEC
TNC-J-C-GN-ST-BH1
RF TNC Connector, 1 Contact(s), Female, Panel Mount, Cable Mount, Crimp Solder Terminal, Locking, Jack, ROHS COMPLIANT
SAMTEC
TNC-J-C-GN-ST-BH2
RF TNC Connector, Female, Panel Mount, Cable Mount, Crimp Solder Terminal, Jack
SAMTEC
TNC-J-C-HN-ST-BH1
RF TNC Connector, 1 Contact(s), Female, Panel Mount, Cable Mount, Crimp Solder Terminal, Locking, Jack, ROHS COMPLIANT
SAMTEC
TNC-J-C-MN-ST-BH1
RF TNC Connector, 1 Contact(s), Female, Panel Mount, Cable Mount, Crimp Solder Terminal, Locking, Jack, ROHS COMPLIANT
SAMTEC
©2020 ICPDF网 联系我们和版权申明