DNL04S0A0R16NFD [DELTA]
Delphi DNS, Non-Isolated Point of Load DC/DC Power Modules: 2.8-5.5Vin, 0.75-3.3V/6Aout; 德尔福DNS ,非隔离负载DC / DC电源模块的点: 2.8-5.5Vin , 0.75-3.3V / 6Aout型号: | DNL04S0A0R16NFD |
厂家: | DELTA ELECTRONICS, INC. |
描述: | Delphi DNS, Non-Isolated Point of Load DC/DC Power Modules: 2.8-5.5Vin, 0.75-3.3V/6Aout |
文件: | 总17页 (文件大小:1011K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
FEATURES
ꢀ
High efficiency: 94% @ 5.0Vin, 3.3V/6A out
ꢀ
Small size and low profile: (SMD)
27.9x 11.4x 7.1mm (1.10”x 0.45”x 0.28”)
Surface mount packaging
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Standard footprint
Voltage and resistor-based trim
Pre-bias startup
Output voltage tracking
No minimum load required
Output voltage programmable from
0.75Vdc to 3.3Vdc via external resistor
Fixed frequency operation
ꢀ
ꢀ
ꢀ
ꢀ
Input UVLO, output OTP, OCP
Remote on/off
ISO 9001, TL 9000, ISO 14001, QS9000,
OHSAS18001 certified manufacturing facility
UL/cUL 60950 (US & Canada) Recognized,
and TUV (EN60950) Certified - pending
CE mark meets 73/23/EEC and 93/68/EEC
directives - pending
ꢀ
ꢀ
Delphi DNS, Non-Isolated Point of Load
DC/DC Power Modules: 2.8-5.5Vin, 0.75-3.3V/6Aout
The Delphi Series DNS, 2.8-5.5V input, single output, non-isolated
Point of Load DC/DC converters are the latest offering from a world
leader in power systems technology and manufacturing -- Delta
Electronics, Inc. The DNS series provides a programmable output
voltage from 0.75V to 3.3V using an external resistor and has flexible
and programmable tracking features to enable a variety of startup
voltages as well as tracking between power modules. This product
family is available in surface mount or SIP packages and provides up
to 6A of output current in an industry standard footprint. With creative
design technology and optimization of component placement, these
converters possess outstanding electrical and thermal performance,
as well as extremely high reliability under highly stressful operating
conditions.
OPTIONS
ꢀ
ꢀ
ꢀ
Negative on/off logic
Tracking feature
SMD package
APPLICATIONS
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Telecom/DataCom
Distributed power architectures
Servers and workstations
LAN/WAN applications
Data processing applications
DATASHEET
DS_DNS04SMD06_10202006
TECHNICAL SPECIFICATIONS
(TA = 25°C, airflow rate = 300 LFM, Vin = 2.8Vdc and 5.5Vdc, nominal Vout unless otherwise noted.)
PARAMETER
NOTES and CONDITIONS
DNS04S0A0S06PFD
Min.
Typ.
Max.
Units
ABSOLUTE MAXIMUM RATINGS
Input Voltage (Continuous)
Tracking Voltage
Operating Temperature
Storage Temperature
0
5.8
Vin,max
127
Vdc
Vdc
°C
Refer to Figure 45 for measuring point
-40
-55
125
°C
INPUT CHARACTERISTICS
Operating Input Voltage
Input Under-Voltage Lockout
Turn-On Voltage Threshold
Turn-Off Voltage Threshold
Maximum Input Current
No-Load Input Current
Off Converter Input Current
Inrush Transient
Recommended Inout Fuse
OUTPUT CHARACTERISTICS
Output Voltage Set Point
Output Voltage Adjustable Range
Output Voltage Regulation
Over Line
Vo ≦ Vin –0.5
2.8
5.5
6
V
2.2
2.0
V
V
A
mA
mA
A2S
A
Vin=2.8V to 5.5V, Io=Io,max
Vin=2.8V to 5.5V, Io=Io,min to Io,max
Vin=5V, Io=Io, max
70
5
0.1
6
-2.0
0.7525
Vo,set
+2.0
3.63
% Vo,set
V
Vin=2.8V to 5.5V
Io=Io,min to Io,max
Ta=-40℃ to 85℃
Over sample load, line and temperature
5Hz to 20MHz bandwidth
0.3
0.4
0.8
% Vo,set
% Vo,set
% Vo,set
% Vo,set
Over Load
Over Temperature
Total Output Voltage Range
Output Voltage Ripple and Noise
Peak-to-Peak
-3.0
0
+3.0
Full Load, 1µF ceramic, 10µF tantalum
Full Load, 1µF ceramic, 10µF tantalum
40
10
60
15
6
mV
mV
A
RMS
Output Current Range
Output Voltage Over-shoot at Start-up
Output DC Current-Limit Inception
Output Short-Circuit Current (Hiccup Mode)
DYNAMIC CHARACTERISTICS
Dynamic Load Response
Positive Step Change in Output Current
Negative Step Change in Output Current
Settling Time to 10% of Peak Deviation
Turn-On Transient
Vout=3.3V
Io,s/c
1
% Vo,set
% Io
Adc
220
3.5
10µF Tan & 1µF Ceramic load cap, 2.5A/µs
50% Io, max to 100% Io, max
100% Io, max to 50% Io, max
160
160
25
mV
mV
µs
Io=Io.max
Start-Up Time, From On/Off Control
Start-Up Time, From Input
Output Voltage Rise Time
Output Capacitive Load
Von/off, Vo=10% of Vo,set
Vin=Vin,min, Vo=10% of Vo,set
Time for Vo to rise from 10% to 90% of Vo,set
Full load; ESR ≧1mΩ
2
2
2
ms
ms
ms
µF
µF
5
1000
3000
Full load; ESR ≧10mΩ
EFFICIENCY
Vo=3.3V
Vo=2.5V
Vo=1.8V
Vo=1.5V
Vo=1.2V
Vo=0.75V
Vin=5V, 100% Load
Vin=5V, 100% Load
Vin=5V, 100% Load
Vin=5V, 100% Load
Vin=5V, 100% Load
Vin=5V, 100% Load
94.0
91.5
89.0
88.0
86.0
81.0
%
%
%
%
%
%
FEATURE CHARACTERISTICS
Switching Frequency
ON/OFF Control, (Negative logic)
Logic Low Voltage
Logic High Voltage
Logic Low Current
Logic High Current
ON/OFF Control, (Positive Logic)
Logic High Voltage
Logic Low Voltage
Logic Low Current
Logic High Current
0Tracking Slew Rate Capability
Tracking Delay Time
Tracking Accuracy
300
kHz
Module On, Von/off
Module Off, Von/off
Module On, Ion/off
Module Off, Ion/off
-0.2
1.5
0.3
Vin,max
10
V
V
µA
mA
0.2
0.2
1
Module On, Von/off
Module Off, Von/off
Module On, Ion/off
Module Off, Ion/off
Vin,max
0.3
1
10
2
V
V
-0.2
mA
µA
V/msec
ms
mV
mV
0.1
10
Delay from Vin.min to application of tracking voltage
Power-up
2V/mS
100
200
200
400
Power-down 1V/mS
GENERAL SPECIFICATIONS
MTBF
Weight
Io=80% of Io, max; Ta=25°C
Refer to Figure 45 for measuring point
13.48
6.5
130
M hours
grams
°C
Over-Temperature Shutdown
2
DS_DNS04SMD6A_10202006
ELECTRICAL CHARACTERISTICS CURVES
98
98
96
94
92
90
88
86
84
97
96
95
94
93
92
91
90
3V
4.5V
5V
5V
5.5V
5.5V
1
2
3
4
5
6
1
2
3
4
5
6
LOAD (A)
LOAD (A)
Figure 1: Converter efficiency vs. output current (3.3V out)
Figure 2: Converter efficiency vs. output current (2.5V out)
98
96
94
92
90
96
94
92
90
88
2.8V
88
86
84
86
84
82
2.8V
5V
5V
5.5V
5.5V
1
2
3
4
5
6
1
2
3
4
5
6
LOAD (A)
LOAD (A)
Figure 3: Converter efficiency vs. output current (1.8V out)
Figure 4: Converter efficiency vs. output current (1.5V out)
94
92
90
88
86
84
82
80
92
90
88
86
84
82
80
2.8V
5V
2.8V
78
76
74
5V
5.5V
5.5V
1
2
3
4
5
6
1
2
3
4
5
6
LOAD (A)
LOAD (A)
Figure 5: Converter efficiency vs. output current (1.2V out)
Figure 6: Converter efficiency vs. output current (0.75V out)
3
DS_DNS04SMD6A_10202006
ELECTRICAL CHARACTERISTICS CURVES (CON.)
Figure 7: Output ripple & noise at 3.3Vin, 2.5V/6A out
Figure 8: Output ripple & noise at 3.3Vin, 1.8V/6A out
Figure 9: Output ripple & noise at 5Vin, 3.3V/6A out
Figure 10: Output ripple & noise at 5Vin, 1.8V/6A out
Figure 11: Turn on delay time at 3.3Vin, 2.5V/6A out
Figure 12: Turn on delay time at 3.3Vin, 1.8V/6A out
4
DS_DNS04SMD6A_10202006
ELECTRICAL CHARACTERISTICS CURVES (CON.)
Figure 13: Turn on delay time at 5Vin, 3.3V/6A out
Figure 14: Turn on delay time at 5Vin, 1.8V/6A out
Figure 16: Turn on delay time at remote turn on 3.3Vin, 2.5V/6A
out
Figure 15: Turn on delay time at remote turn on 5Vin, 3.3V/6A out
Figure 17: Turn on delay time at remote turn on with external
Figure 18: Turn on delay time at remote turn on with external
capacitors (Co= 3000 µF) 5Vin, 3.3V/6A out
capacitors (Co= 3000 µF) 3.3Vin, 2.5V/6A out
5
DS_DNS04SMD6A_10202006
ELECTRICAL CHARACTERISTICS CURVES
Figure 19: Typical transient response to step load change at
2.5A/µS from 100% to 50% of Io, max at 5Vin, 3.3Vout
(Cout = 1uF ceramic, 10µF tantalum)
Figure 20: Typical transient response to step load change at
2.5A/µS from 50% to 100% of Io, max at 5Vin, 3.3Vout
(Cout =1uF ceramic, 10µF tantalum)
Figure 21: Typical transient response to step load change at
2.5A/µS from 100% to 50% of Io, max at 5Vin, 1.8Vout
(Cout =1uF ceramic, 10µF tantalum)
Figure 22: Typical transient response to step load change at
2.5A/µS from 50% to 100% of Io, max at 5Vin, 1.8Vout
(Cout = 1uF ceramic, 10µF tantalum)
6
DS_DNS04SMD6A_10202006
ELECTRICAL CHARACTERISTICS CURVES (CON.)
Figure 23: Typical transient response to step load change at
2.5A/µS from 100% to 50% of Io, max at 3.3Vin,
2.5Vout (Cout =1uF ceramic, 10µF tantalum)
Figure 24: Typical transient response to step load change at
2.5A/µS from 50% to 100% of Io, max at 3.3Vin,
2.5Vout (Cout =1uF ceramic, 10µF tantalum)
Figure 25: Typical transient response to step load change at
2.5A/µS from 100% to 50% of Io, max at 3.3Vin,
1.8Vout (Cout =1uF ceramic, 10µF tantalum)
Figure 26: Typical transient response to step load change at
2.5A/µS from 50% to 100% of Io, max at 3.3Vin,
1.8Vout (Cout = 1uF ceramic, 10µF tantalum)
Figure 27: Output short circuit current 5Vin, 0.75Vout
Figure 28:Turn on with Prebias 5Vin, 3.3V/0A out, Vbias =1.0Vdc
7
DS_DNS04SMD6A_10202006
DESIGN CONSIDERATIONS
TEST CONFIGURATIONS
Input Source Impedance
TO OSCILLOSCOPE
To maintain low noise and ripple at the input voltage, it is
critical to use low ESR capacitors at the input to the
module. Figure 32 shows the input ripple voltage (mVp-p)
for various output models using 2x100 µF low ESR
tantalum capacitor (KEMET p/n: T491D107M016AS,
AVX p/n: TAJD107M106R, or equivalent) in parallel with
47 µF ceramic capacitor (TDK p/n:C5750X7R1C476M or
equivalent). Figure 33 shows much lower input voltage
ripple when input capacitance is increased to 400 µF (4 x
100 µF) tantalum capacitors in parallel with 94 µF (2 x 47
µF) ceramic capacitor.
L
VI(+)
100uF
2
Tantalum
BATTERY
VI(-)
Note: Input reflected-ripple current is measured with a
simulated source inductance. Current is measured at
the input of the module.
Figure 29: Input reflected-ripple test setup
The input capacitance should be able to handle an AC
ripple current of at least:
Vout
Vin
Vout
Vin
⎛
⎜
⎞
⎟
Irms = Iout
1−
Arms
COPPER STRIP
⎝
⎠
Vo
200
150
100
50
Resistive
Load
1uF
10uF
tantalum ceramic
SCOPE
GND
3.3Vin
5.0Vin
Note: Use a 10µF tantalum and 1µF capacitor. Scope
measurement should be made using a BNC connector.
0
0
1
2
3
4
Output Voltage (Vdc)
Figure 30: Peak-peak output noise and startup transient
measurement test setup.
Figure 32: Input voltage ripple for various output models, Io =
6A (CIN = 2×100µF tantalum // 47µF ceramic)
CONTACT AND
DISTRIBUTION LOSSES
80
60
40
V
I
Vo
I
I
Io
LOAD
SUPPLY
GND
20
CONTACT RESISTANCE
3.3Vin
5.0Vin
0
Figure 31: Output voltage and efficiency measurement test
setup
0
1
2
3
4
Output Voltage (Vdc)
Note: All measurements are taken at the module terminals.
When the module is not soldered (via socket), place
Kelvin connections at module terminals to avoid
measurement errors due to contact resistance.
Figure 33: Input voltage ripple for various output models, Io =
6A (CIN = 4×100µF tantalum // 2×47µF ceramic)
Vo× Io
Vi × Ii
η = (
)×100 %
8
DS_DNS04SMD6A_10202006
FEATURES DESCRIPTIONS
DESIGN CONSIDERATIONS (CON.)
Remote On/Off
The power module should be connected to a low
ac-impedance input source. Highly inductive source
impedances can affect the stability of the module. An
input capacitance must be placed close to the modules
input pins to filter ripple current and ensure module
stability in the presence of inductive traces that supply
the input voltage to the module.
The DNS series power modules have an On/Off pin for
remote On/Off operation. Both positive and negative
On/Off logic options are available in the DNS series power
modules.
For positive logic module, connect an open collector
(NPN) transistor or open drain (N channel) MOSFET
between the On/Off pin and the GND pin (see figure 34).
Positive logic On/Off signal turns the module ON during
the logic high and turns the module OFF during the logic
low. When the positive On/Off function is not used, leave
the pin floating or tie to Vin (module will be On).
Safety Considerations
For safety-agency approval the power module must be
installed in compliance with the spacing and separation
requirements of the end-use safety agency standards.
For the converter output to be considered meeting the
requirements of safety extra-low voltage (SELV), the
input must meet SELV requirements. The power module
has extra-low voltage (ELV) outputs when all inputs are
ELV.
For negative logic module, the On/Off pin is pulled high
with an external pull-up resistor (see figure 35). Negative
logic On/Off signal turns the module OFF during logic high
and turns the module ON during logic low. If the negative
On/Off function is not used, leave the pin floating or tie to
GND. (module will be On)
The input to these units is to be provided with a
maximum 6A time-delay fuse in the ungrounded lead.
Vo
Vin
ION/OFF
On/Off
RL
Q1
GND
Figure 34: Positive remote On/Off implementation
Vo
Vin
Rpull-
up
ION/OFF
On/Off
RL
Q1
GND
Figure 35: Negative remote On/Off implementation
Over-Current Protection
To provide protection in an output over load fault
condition, the unit is equipped with internal over-current
protection. When the over-current protection is
triggered, the unit enters hiccup mode. The units
operate normally once the fault condition is removed.
9
DS_DNS04SMD6A_10202006
Vtrim = 0.7 − 0.1698×
Vo − 0.7525
FEATURES DESCRIPTIONS (CON.)
For example, to program the output voltage of a DNS
module to 3.3 Vdc, Vtrim is calculated as follows
Over-Temperature Protection
The over-temperature protection consists of circuitry that
provides protection from thermal damage. If the
temperature exceeds the over-temperature threshold the
module will shut down. The module will try to restart after
shutdown. If the over-temperature condition still exists
during restart, the module will shut down again. This
restart trial will continue until the temperature is within
specification.
Vtrim = 0.7 − 0.1698×
3.3 − 0.7525 = 0.267V
)
Vo
RLoad
TRIM
Rtrim
GND
Remote Sense
Figure 37: Circuit configuration for programming output voltage
The DNS provide Vo remote sensing to achieve proper
regulation at the load points and reduce effects of
distribution losses on output line. In the event of an open
remote sense line, the module shall maintain local sense
regulation through an internal resistor. The module shall
correct for a total of 0.5V of loss. The remote sense line
impedance shall be < 10Ω.
using an external resistor
Vo
Vtrim
RLoad
TRIM
GND
+
_
Distribution Losses
Distribution Losses
Vo
Vin
Figure 38: Circuit Configuration for programming output voltage
using external voltage source
Sense
RL
Table 1 provides Rtrim values required for some common
output voltages, while Table 2 provides value of external
voltage source, Vtrim, for the same common output
voltages. By using a 1% tolerance trim resistor, set point
tolerance of ±2% can be achieved as specified in the
electrical specification.
GND
Distribution
Distribution
Figure 36: Effective circuit configuration for remote sense
operation
Output Voltage Programming
Table 1
Vo(V)
0.7525
1.2
Rtrim(KΩ)
Open
41.97
23.08
15.00
6.95
The output voltage of the DNS can be programmed to any
voltage between 0.75Vdc and 3.3Vdc by connecting one
resistor (shown as Rtrim in Figure 37) between the TRIM
and GND pins of the module. Without this external
resistor, the output voltage of the module is 0.7525 Vdc. To
calculate the value of the resistor Rtrim for a particular
output voltage Vo, please use the following equation:
1.5
1.8
2.5
3.3
3.16
21070
⎡
⎣
⎤
⎦
Rtrim =
− 5110 Ω
⎢
⎥
Vo − 0.7525
Table 2
For example, to program the output voltage of the DNS
module to 1.8Vdc, Rtrim is calculated as follows:
Vo(V)
0.7525
1.2
Vtrim(V)
Open
21070
⎡
⎤
⎦
0.624
0.573
0.522
0.403
0.267
Rtrim =
− 5110 Ω = 15KΩ
⎢
⎣
⎥
1.5
1.8 − 0.7525
1.8
DNS can also be programmed by apply a voltage between
the TRIM and GND pins (Figure 38). The following
equation can be used to determine the value of Vtrim
needed for a desired output voltage Vo:
2.5
3.3
10
DS_DNS04SMD6A_10202006
FEATURE DESCRIPTIONS (CON.)
The output voltage tracking feature (Figure 40 to Figure
42) is achieved according to the different external
connections. If the tracking feature is not used, the
TRACK pin of the module can be left unconnected or tied
to Vin.
The amount of power delivered by the module is the
voltage at the output terminals multiplied by the output
current. When using the trim feature, the output voltage of
the module can be increased, which at the same output
current would increase the power output of the module.
Care should be taken to ensure that the maximum output
power of the module must not exceed the maximum rated
power (Vo.set x Io.max ≤ P max).
For proper voltage tracking, input voltage of the tracking
power module must be applied in advance, and the
remote on/off pin has to be in turn-on status. (Negative
logic: Tied to GND or unconnected. Positive logic: Tied to
Vin or unconnected)
Voltage Margining
Output voltage margining can be implemented in the DNS
modules by connecting a resistor, R margin-up, from the Trim
pin to the ground pin for margining-up the output voltage
and by connecting a resistor, Rmargin-down, from the Trim pin
to the output pin for margining-down. Figure 39 shows the
circuit configuration for output voltage margining. If
unused, leave the trim pin unconnected. A calculation tool
is available from the evaluation procedure which
computes the values of R margin-up and Rmargin-down for a
specific output voltage and margin percentage.
PS1
PS2
PS1
PS2
Figure 40: Sequential Start-up
Vo
Vin
PS1
PS2
PS1
PS2
Rmargin-down
Q1
Trim
GND
On/Off
Rmargin-up
Q2
Rtrim
Figure 41: Simultaneous
Figure 39: Circuit configuration for output voltage margining
PS1
PS2
PS1
+∆V
PS2
Voltage Tracking
The DNS family was designed for applications that have
output voltage tracking requirements during power-up and
power-down. The devices have a TRACK pin to
implement three types of tracking method: sequential
start-up, simultaneous and ratio-metric. TRACK simplifies
the task of supply voltage tracking in a power system by
enabling modules to track each other, or any external
voltage, during power-up and power-down.
Figure 42: Ratio-metric
By connecting multiple modules together, customers can
get multiple modules to track their output voltages to the
voltage applied on the TRACK pin.
11
DS_DNS04SMD6A_10202006
FEATURE DESCRIPTIONS (CON.)
Ratio-Metric
Sequential Start-up
Ratio–metric (Figure 42) is implemented by placing the
voltage divider on the TRACK pin that comprises R1 and
R2, to create a proportional voltage with VoPS1 to the Track
pin of PS2.
Sequential start-up (Figure 40) is implemented by placing
an On/Off control circuit between VoPS1 and the On/Off pin
of PS2.
For Ratio-Metric applications that need the outputs of PS1
and PS2 reach the regulation set point at the same time.
PS1
PS2
Vin
Vin
The following equation can be used to calculate the value
of R1 and R2.
VoPS1
VoPS2
R3
The suggested value of R2 is 10kΩ.
On/Off
R1
Q1
C1
On/Off
VO,PS 2
R2
R2
=
VO,PS1 R1 + R2
PS1
PS2
Vin
Vin
Simultaneous
VoPS1
VoPS2
R1
TRACK
On/Off
Simultaneous tracking (Figure 41) is implemented by
using the TRACK pin. The objective is to minimize the
voltage difference between the power supply outputs
during power up and down.
R2
On/Off
The high for positive logic
The low for negative logic
The simultaneous tracking can be accomplished by
connecting VoPS1 to the TRACK pin of PS2. Please note
the voltage apply to TRACK pin needs to always higher
than the VoPS2 set point voltage.
PS2
PS1
Vin
Vin
VoPS1
VoPS2
TRACK
On/Off
On/Off
12
DS_DNS04SMD6A_10202006
THERMAL CONSIDERATIONS
THERMAL CURVES
Thermal management is an important part of the system
design. To ensure proper, reliable operation, sufficient
cooling of the power module is needed over the entire
temperature range of the module. Convection cooling is
usually the dominant mode of heat transfer.
Hence, the choice of equipment to characterize the
thermal performance of the power module is a wind
tunnel.
Thermal Testing Setup
Delta’s DC/DC power modules are characterized in
heated vertical wind tunnels that simulate the thermal
environments encountered in most electronics
equipment. This type of equipment commonly uses
vertically mounted circuit cards in cabinet racks in which
the power modules are mounted.
Figure 44: Temperature measurement location
The allowed maximum hot spot temperature is defined at 127℃
DNS04S0A0S06(Standard) Output Current vs. Ambient Temperature and Air Velocity
Output Current(A)
@ Vin=5V, Vout = 3.3V(Either Orientation)
The following figure shows the wind tunnel
characterization setup. The power module is mounted
on a test PWB and is vertically positioned within the
wind tunnel. The height of this fan duct is constantly kept
at 25.4mm (1’’).
7
6
5
4
Natural
Thermal Derating
Convection
3
Heat can be removed by increasing airflow over the
module. To enhance system reliability, the power
module should always be operated below the maximum
operating temperature. If the temperature exceeds the
maximum module temperature, reliability of the unit may
be affected.
2
1
0
25
35
45
55
65
75
85
Ambient Temperature (℃)
PWB
FACING PWB
Figure 45: Output current vs. ambient temperature and air
velocity@Vin=5V, Vout=3.3V(Either Orientation)
MODULE
DNS04S0A0S06(Standard) Output Current vs. Ambient Temperature and Air Velocity
Output Current(A)
@ Vin=5V, Vout = 1.5V(Either Orientation)
7
6
5
AIR VELOCITY
AND AMBIENT
TEMPERATURE
MEASURED BELOW
THE MODULE
50.8 (2.0”)
AIR FLOW
4
Natural
Convection
3
12.7 (0.5”)
25.4 (1.0”)
2
1
0
Note: Wind Tunnel Test Setup Figure Dimensions are in millimeters and (Inches)
Figure 43: Wind tunnel test setup
25
35
45
55
65
75
85
Ambient Temperature (℃)
Figure 46: Output current vs. ambient temperature and air
velocity@Vin=5V, Vout=1.5V(Either Orientation)
13
DS_DNS04SMD6A_10202006
DNS04S0A0S06(Standard) Output Current vs. Ambient Temperature and Air Velocity
DNS04S0A0S06(Standard) Output Current vs. Ambient Temperature and Air Velocity
Output Current(A)
@ Vin=5V, Vout = 0.75V(Either Orientation)
Output Current(A)
@ Vin=3.3V, Vout = 0.75V(Either Orientation)
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
Natural
Convection
Natural
Convection
25
35
45
55
65
75
85
25
35
45
55
65
75
85
Ambient Temperature (℃)
Ambient Temperature (℃)
Figure 47: Output current vs. ambient temperature and air
velocity@Vin=5V, Vout=0.75V(Either Orientation)
Figure 50: Output current vs. ambient temperature and air
velocity@Vin=3.3V, Vout=0.75V(Either Orientation)
DNS04S0A0S06(Standard) Output Current vs. Ambient Temperature and Air Velocity
Output Current(A)
@ Vin=3.3V, Vout = 2.5V(Either Orientation)
7
6
5
4
Natural
Convection
3
2
1
0
25
35
45
55
65
75
85
Ambient Temperature (℃)
Figure 48: Output current vs. ambient temperature and air
velocity@Vin=3.3V, Vout=2.5V(Either Orientation)
DNS04S0A0S06(Standard) Output Current vs. Ambient Temperature and Air Velocity
Output Current(A)
@ Vin=3.3V, Vout = 1.5V(Either Orientation)
7
6
5
4
Natural
Convection
3
2
1
0
25
35
45
55
65
75
85
Ambient Temperature (℃)
Figure 49: Output current vs. ambient temperature and air
velocity@Vin=3.3V, Vout=1.5V(Either Orientation)
14
PICK AND PLACE LOCATION
SURFACE-MOUNT TAPE & REEL
LEAD (Sn/Pb) PROCESS RECOMMEND TEMP. PROFILE
Peak temp.
2nd Ramp-up temp.
210~230°C 5sec.
1.0~3.0°C /sec.
250
Pre-heat temp.
140~180°C 60~120 sec.
200
Cooling down rate <3°C /sec.
Ramp-up temp.
0.5~3.0°C /sec.
150
100
50
Over 200°C
40~50sec.
0
60
120
Time ( sec. )
180
240
300
LEAD FREE (SAC) PROCESS RECOMMEND TEMP. PROFILE
.
Temp
Peak Temp. 240 ~ 245
℃
220℃
200℃
Ramp down
max. 4 /sec.
℃
Preheat time
90~120 sec.
150℃
25℃
Time Limited 75 sec.
above 220
℃
Ramp up
max. 3 /sec.
℃
Time
Note: All temperature refers to assembly application board, measured on the land of assembly application board.
15
DS_DNS04SMD6A_10202006
MECHANICAL DRAWING
SMD PACKAGE
SIP PACKAGE (OPTIONAL)
16
DS_DNS04SMD6A_10202006
PART NUMBERING SYSTEM
DNS
04
S
0A0
S
06
P
F
D
On/Off
logic
Product
Series
Numbers of
Outputs
Output
Voltage
Package
Type
Output
Current
Input Voltage
Option Code
DNS - 6A
DNM - 10A
DNL - 16A
04 - 2.8~5.5V
10 – 8.3~14V
S - Single
0A0 -
R - SIP
06 - 6A
N- negative
P- positive
F- RoHS 6/6
(Lead Free)
D - Standard Function:
Programmable S - SMD
10 - 10A
16 - 16A
MODEL LIST
Efficiency
5.0Vin, 3.3Vdc @ 6A
Model Name
Packaging
Input Voltage
Output Voltage Output Current
DNS04S0A0S06NFD
SMD
2.8 ~ 5.5Vdc
0.75 V~ 3.3Vdc
6A
94.0%
DNS04S0A0S06PFD
DNS04S0A0R06NFD
DNS04S0A0R06PFD
SMD
SIP
2.8 ~ 5.5Vdc
2.8 ~ 5.5Vdc
2.8 ~ 5.5Vdc
0.75 V~ 3.3Vdc
0.75 V~ 3.3Vdc
0.75 V~ 3.3Vdc
6A
6A
6A
94.0%
94.0%
94.0%
SIP
CONTACT: www.delta.com.tw/dcdc
USA:
Telephone:
East Coast: (888) 335 8201
West Coast: (888) 335 8208
Fax: (978) 656 3964
Email: DCDC@delta-corp.com
Europe:
Telephone: +41 31 998 53 11
Fax: +41 31 998 53 53
Asia & the rest of world:
Telephone: +886 3 4526107 x6220
Fax: +886 3 4513485
Email: DCDC@delta-es.tw
Email: DCDC@delta.com.tw
WARRANTY
Delta offers a two (2) year limited warranty. Complete warranty information is listed on our web site or is available upon
request from Delta.
Information furnished by Delta is believed to be accurate and reliable. However, no responsibility is assumed by Delta
for its use, nor for any infringements of patents or other rights of third parties, which may result from its use. No license
is granted by implication or otherwise under any patent or patent rights of Delta. Delta reserves the right to revise these
specifications at any time, without notice.
17
DS_DNS04SMD6A_10202006
相关型号:
DNL04S0A0R16PFA
Delphi DNL, Non-Isolated Point of Load DC/DC Power Modules: 2.8-5.5Vin, 0.75-3.3V/16A out
DELTA
DNL04S0A0R16PFB
Delphi DNL, Non-Isolated Point of Load DC/DC Power Modules: 2.8-5.5Vin, 0.75-3.3V/16A out
DELTA
DNL04S0A0R16PFC
Delphi DNL, Non-Isolated Point of Load DC/DC Power Modules: 2.8-5.5Vin, 0.75-3.3V/16A out
DELTA
DNL04S0A0R16PFD
Delphi DNS, Non-Isolated Point of Load DC/DC Power Modules: 2.8-5.5Vin, 0.75-3.3V/6Aout
DELTA
DNL04S0A0S06NFD
Delphi DNS, Non-Isolated Point of Load DC/DC Power Modules: 2.8-5.5Vin, 0.75-3.3V/6Aout
DELTA
DNL04S0A0S06PFD
Delphi DNS, Non-Isolated Point of Load DC/DC Power Modules: 2.8-5.5Vin, 0.75-3.3V/6Aout
DELTA
DNL04S0A0S10NFA
Delphi DNM, Non-Isolated Point of Load DC/DC Power Modules: 2.8-5.5Vin, 0.75-3.3V/10A out
DELTA
DNL04S0A0S10NFB
Delphi DNM, Non-Isolated Point of Load DC/DC Power Modules: 2.8-5.5Vin, 0.75-3.3V/10A out
DELTA
©2020 ICPDF网 联系我们和版权申明