Q48SK12025NRFN [DELTA]
Delphi Series Q48SK, Quarter Brick Family DC/DC Power Modules: 36~75V in, 12V/25A out, 300W; 德尔福系列Q48SK , 1/4砖系列DC / DC模块电源: 36 〜 75V , 12V / 25A输出, 300W型号: | Q48SK12025NRFN |
厂家: | DELTA ELECTRONICS, INC. |
描述: | Delphi Series Q48SK, Quarter Brick Family DC/DC Power Modules: 36~75V in, 12V/25A out, 300W |
文件: | 总13页 (文件大小:389K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
FEATURES
High efficiency : 95.2% @ 12V/25A
Size:
57.9x36.8x11.2mm (2.28”x1.45”x0.44”)
(W/o heat spreader)
57.9*36.8*12.7mm (2.28”*1.45”0.50”)
(With heat spreader)
Standard footprint
Industry standard pin out
Fixed frequency operation
Input UVLO, Output OCP, OVP, OTP
Hiccup output over current protection
(OCP)
Hiccup output over voltage protection
(OVP)
Auto recovery OTP and input UVLO
2250V isolation and basic insulation
No minimum load required
ISO 9001, TL 9000, ISO 14001, QS9000,
OHSAS18001 certified manufacturing
facility
UL/cUL 60950-1 (US & Canada)
recognized
Delphi Series Q48SK, Quarter Brick Family
DC/DC Power Modules:
36~75V in, 12V/25A out, 300W
OPTIONS
The Delphi series Q48SK12025, quarter brick, 36~75V input, single output,
isolated DC/DC converter is the latest offering from a world leader in power
system and technology and manufacturing ― Delta Electronics, Inc. This
product provides up to 300 watts of power in an industry standard footprint
and pin out. With creative design technology and optimization of component
placement, these converters possess outstanding electrical and thermal
performances, as well as extremely high reliability under highly stressful
operating conditions. The Q48SK12025 offers more than 95.2% high
efficiency at 25A full load. The Q48SK12025 is fully protected from abnormal
input/output voltage, current, and temperature conditions and meets all
safety requirements with basic insulation.
Latched over current protection
Positive On/Off logic
Heat spreader available for
extended operation.
APPLICATIONS
Telecom / Datacom
Wireless Networks
Optical Network Equipment
Server and Data Storage
Industrial / Testing Equipment
DATASHEET
DS_Q48SK12025_07012010
TECHNICAL SPECIFICATIONS
(TA=25°C, airflow rate=300 LFM, Vin=48Vdc, nominal Vout unless otherwise noted;
PARAMETER
NOTES and CONDITIONS
Q48SK12025 (Standard)
Min.
Typ.
Max.
Units
ABSOLUTE MAXIMUM RATINGS
Input Voltage
Continuous
80
100
118
112
125
2250
Vdc
Vdc
°C
Transient
100ms
Operating Hot Spot Temperature (Without heat spreader)
Operating Case Temperature (With heat spreader)
Storage Temperature
Refer to figure 18 for measuring point
Refer to figure 20 for measuring point
-40
-40
-55
°C
°C
Input/Output Isolation Voltage
INPUT CHARACTERISTICS
Operating Input Voltage
Vdc
36
48
75
Vdc
Input Under-Voltage Lockout
Turn-On Voltage Threshold
Turn-Off Voltage Threshold
Lockout Hysteresis Voltage
Maximum Input Current
32.0
30.0
34.0
32.0
2
36.0
34.0
Vdc
Vdc
Vdc
A
100% Load, 36Vin
Vin=48V, Io=0A
Vin=48V, Io=0A
11
No-Load Input Current
160
10
mA
mA
A2s
mA
dB
Off Converter Input Current
Inrush Current (I2t)
1
Input Reflected-Ripple Current
Input Voltage Ripple Rejection
OUTPUT CHARACTERISTICS
Output Voltage Set Point
P-P thru 12µH inductor, 5Hz to 20MHz
120 Hz
10
-30
Vin=48V, Io=0, Tc=25°C
11.4
11.2
11.7
12.0
Vdc
Output Voltage Regulation
Over Load
Vin=48V, Io=Io,min to Io,max
Vin=36V to 75V, Io=Io min
Vin=48V, Tc=-40°C to 85°C
±30
±50
±100
±80
mV
mV
mV
Vdc
Over Line
Over Temperature
Total Output Voltage Range
Output Voltage Ripple and Noise
Peak-to-Peak
over sample load, line and temperature
5Hz to 20MHz bandwidth
12.0
Full Load, 1µF ceramic, 10µF tantalum
Full Load, 1µF ceramic, 10µF tantalum
120
50
mV
mV
A
RMS
Operating Output Current Range
Output DC Current-Limit Inception
DYNAMIC CHARACTERISTICS
Output Voltage Current Transient
Positive Step Change in Output Current
Negative Step Change in Output Current
Settling Time (within 1% Vout nominal)
Turn-On Transient
0
25
Output Voltage 10% Low
110
140
%
48V, 10µF Tan & 1µF Ceramic load cap, 0.1A/µs
50% Io.max to 75% Io.max
300
300
300
mV
mV
µs
75% Io.max to 50% Io.max
Start-Up Time, From On/Off Control
Start-Up Time, From Input
Maximum Output Capacitance
EFFICIENCY
70
80
ms
ms
µF
Full load;
20000
2250
100% Load
Vin=48V
Vin=48V
95.2
94.7
%
%
60% Load
ISOLATION CHARACTERISTICS
Input to Output
Vdc
MΩ
pF
Isolation Resistance
10
Isolation Capacitance
1000
160
FEATURE CHARACTERISTICS
Switching Frequency
kHz
ON/OFF Control, Negative Remote On/Off logic
Logic Low (Module On)
Von/off at Ion/off=1.0mA
Von/off at Ion/off=0.0 µA
0
2
0.8
50
V
V
Logic High (Module Off)
ON/OFF Control, Positive Remote On/Off logic
Logic Low (Module Off)
Von/off at Ion/off=1.0mA
Von/off at Ion/off=0.0 µA
0
2
0.8
50
1
V
V
Logic High (Module On)
ON/OFF Current (for both remote on/off logic)
Leakage Current (for both remote on/off logic)
Output Over-Voltage Protection
GENERAL SPECIFICATIONS
MTBF(with heat spreader)
Weight(without heat spreader)
Weight(with heat spreader)
Over-Temperature Shutdown ( Without heat spreader)
Ion/off at Von/off=0.0V
mA
uA
%
Logic High, Von/off=15V
50
140
Over full temp range; % of nominal Vout
115
Io=100% of Io, max; Tc=40°C;Airflow=600LFM
2.6
50.5
65.5
126
122
M hours
grams
grams
°C
Refer to figure 18 for measuring point
Refer to figure 20 for measuring point
Over-Temperature Shutdown
(With heat spreader)
°C
DS_Q48SK12025_07012010
2
ELECTRICAL CHARACTERISTICS CURVES
20
18
16
14
12
10
8
98
96
94
92
90
88
86
84
82
80
78
76
74
6
4
48V
36V
75V
48V
8
36V
75V
2
72
70
0
0
2
4
6
8
10 12 14 16 18 20 22 24 26
0
2
4
6
10 12 14 16 18 20 22 24 26
Figure 1: Efficiency vs. load current for minimum, nominal, and
Figure 2: Power dissipation vs. load current for minimum,
maximum input voltage at 85°C.
nominal, and maximum input voltage at 85°C.
9
8
7
6
5
4
3
2
30
35
40
45
50
55
60
65
70
75
I NPUT VOLTAGE ( V)
Figure 3: Typical full load input characteristics at room
temperature.
DS_Q48SK12025_07012010
3
ELECTRICAL CHARACTERISTICS CURVES
For Negative Remote On/Off Logic
Figure 4: Turn-on transient at zero load current) (20ms/div).
Figure 5: Turn-on transient at full rated load current (20
Top Trace: Vout; 5V/div; Bottom Trace: ON/OFF input: 2V/div.
ms/div). Top Trace: Vout: 5V/div; Bottom Trace: ON/OFF input:
2V/div.
For Input Voltage Start up
Figure 6: Turn-on transient at zero load current (20 ms/div).
Top Trace: Vout; 5V/div; Bottom Trace: input voltage: 30V/div.
Figure 7: Turn-on transient at full rated load current (20
ms/div). Top Trace: Vout; 5V/div; Bottom Trace: input voltage:
30V/div.
DS_Q48SK12025_07012010
4
ELECTRICAL CHARACTERISTICS CURVES
Figure 8: Output voltage response to step-change in load
current (75%-50% of Io, max; di/dt = 0.1A/µs). Load cap: 10µF,
tantalum capacitor and 1µF ceramic capacitor. Top Trace: Vout;
100mV/div; Bottom Trace: output current: 10A/div
Figure 9: Output voltage response to step-change in load
current (50%-75% of Io, max; di/dt = 0.1A/µs). Load cap: 10µF,
tantalum capacitor and 1µF ceramic capacitor. Top Trace:
Vout; 100mV/div; Bottom Trace: output current: 10A/div
Figure 10: Test set-up diagram showing measurement points
for Input Terminal Ripple Current and Input Reflected Ripple
Current.
Figure 11: Input Terminal Ripple Current, ic, at full rated output
current and nominal input voltage with 12µH source impedance
and 33µF electrolytic capacitor (200 mA/div,2us/div).
Note: Measured input reflected-ripple current with a simulated
source Inductance (LTEST) of 12 µH. Capacitor Cs offset
possible battery impedance. Measure current as shown above.
DS_Q48SK12025_07012010
5
ELECTRICAL CHARACTERISTICS CURVES
Figure 12: Input reflected ripple current, is, through a 12µH
source inductor at nominal input voltage and rated load current
(20 mA/div,2us/div).
Figure 13: Output voltage noise and ripple measurement test
setup.
14
12
10
8
6
4
2
0
0
5
10
15
20
25
30
35
OUTPUT CURRENT ( A)
Figure 14: Output voltage ripple at nominal input voltage and
rated load current (Io=25A)(10 mV/div, 2us/div)
Load capacitance: 1µF ceramic capacitor and 10µF tantalum
capacitor. Bandwidth: 20 MHz.
Figure 15: Output voltage vs. load current showing typical
current limit curves and converter shutdown points.
DS_Q48SK12025_07012010
6
The input source must be insulated from the ac
mains by reinforced or double insulation.
DESIGN CONSIDERATIONS
Input Source Impedance
The input terminals of the module are not operator
accessible.
The impedance of the input source connecting to the
DC/DC power modules will interact with the modules
and affect the stability. A low ac-impedance input source
is recommended. If the source inductance is more than
a few µH, we advise adding a 10µF to 100µF electrolytic
capacitor (ESR < 0.7 Ω at 100 kHz) mounted close to
the input of the module to improve the stability.
If the metal baseplate is grounded, the output must
be also grounded.
A SELV reliability test is conducted on the system
where the module is used, in combination with the
module, to ensure that under a single fault,
hazardous voltage does not appear at the module’s
output.
Layout and EMC Considerations
Delta’s DC/DC power modules are designed to operate
in a wide variety of systems and applications. For design
assistance with EMC compliance and related PWB
layout issues, please contact Delta’s technical support
team. An external input filter module is available for
easier EMC compliance design. Application notes to
assist designers in addressing these issues are pending
release.
When installed into a Class II equipment (without
grounding), spacing consideration should be given to
the end-use installation, as the spacing between the
module and mounting surface have not been evaluated.
The power module has extra-low voltage (ELV) outputs
when all inputs are ELV.
This power module is not internally fused. To achieve
optimum safety and system protection, an input line fuse
is highly recommended. The safety agencies require a
normal-blow fuse with 30A maximum rating to be
installed in the ungrounded lead. A lower rated fuse can
be used based on the maximum inrush transient energy
and maximum input current.
Safety Considerations
The power module must be installed in compliance with
the spacing and separation requirements of the
end-user’s safety agency standard, i.e., UL60950-1,
CAN/CSA-C22.2, No. 60950-1 and EN60950-1+A11 and
IEC60950-1, if the system in which the power module is
to be used must meet safety agency requirements.
Soldering and Cleaning Considerations
Basic insulation based on 75 Vdc input is provided
between the input and output of the module for the
purpose of applying insulation requirements when the
input to this DC-to-DC converter is identified as TNV-2
or SELV. An additional evaluation is needed if the
source is other than TNV-2 or SELV.
Post solder cleaning is usually the final board assembly
process before the board or system undergoes electrical
testing. Inadequate cleaning and/or drying may lower the
reliability of a power module and severely affect the
finished circuit board assembly test. Adequate cleaning
and/or drying is especially important for un-encapsulated
and/or open frame type power modules. For assistance
on appropriate soldering and cleaning procedures,
please contact Delta’s technical support team.
When the input source is SELV circuit, the power module
meets SELV (safety extra-low voltage) requirements. If
the input source is a hazardous voltage which is greater
than 60 Vdc and less than or equal to 75 Vdc, for the
module’s output to meet SELV requirements, all of the
following must be met:
DS_Q48SK12025_07012010
7
FEATURES DESCRIPTIONS
Over-Current Protection
The modules include an internal output over-current
protection circuit, which will endure current limiting for
an unlimited duration during output overload. If the
output current exceeds the OCP set point, the modules
will shut down (hiccup mode).
The modules will try to restart after shutdown. If the
overload condition still exists, the module will shut down
again. This restart trial will continue until the overload
condition is corrected.
Figure 16: Remote on/off implementation
Over-Voltage Protection
The modules include an internal output over-voltage
protection circuit, which monitors the voltage on the
output terminals. If this voltage exceeds the
over-voltage set point, the protection circuit will
constrain the max duty clcyle to limit the output voltage,
if the output voltage continlously increases the modules
will shut down, and then restart after a hiccup-time
(hiccup mode).
Over-Temperature Protection
The over-temperature protection consists of circuitry
that provides protection from thermal damage. If the
temperature exceeds the over-temperature threshold
the module will shut down. The module will restart after
the temperature is within specification.
Remote On/Off
The remote on/off feature on the module can be either
negative or positive logic. Negative logic turns the
module on during a logic low and off during a logic high.
Positive logic turns the modules on during a logic high
and off during a logic low.
Remote on/off can be controlled by an external switch
between the on/off terminal and the Vi (-) terminal. The
switch can be an open collector or open drain.
For negative logic if the remote on/off feature is not
used, please short the on/off pin to Vi (-). For positive
logic if the remote on/off feature is not used, please
leave the on/off pin to floating.
DS_Q48SK12025_07012010
8
THERMAL CONSIDERATIONS
Thermal management is an important part of the system
design. To ensure proper, reliable operation, sufficient
cooling of the power module is needed over the entire
temperature range of the module. Convection cooling is
usually the dominant mode of heat transfer.
Hence, the choice of equipment to characterize the
thermal performance of the power module is a wind
tunnel.
Thermal Testing Setup
Delta’s DC/DC power modules are characterized in
heated vertical wind tunnels that simulate the thermal
environments encountered in most electronics
equipment. This type of equipment commonly uses
vertically mounted circuit cards in cabinet racks in which
the power modules are mounted.
The following figure shows the wind tunnel
characterization setup. The power module is mounted
on a test PWB and is vertically positioned within the
wind tunnel. The space between the neighboring PWB
and the top of the power module is constantly kept at
6.35mm (0.25’’).
PWB
MODULE
FACING PWB
AIR VELOCITY
AND AMBIENT
TEMPERATURE
MEASURED BELOW
THE MODULE
AIR FLOW
Note: Wind Tunnel Test Setup Figure Dimensions are in millimeters and (Inches)
Figure 17: Wind tunnel test setup
Thermal Derating
Heat can be removed by increasing airflow over the
module. To enhance system reliability, the power
module should always be operated below the maximum
operating temperature. If the temperature exceeds the
maximum module temperature, reliability of the unit may
be affected.
DS_Q48SK12025_07012010
9
THERMAL CURVES
THERMAL CURVES
(WITHOUT HEAT SPREADER)
(WITH HEAT SPREADER)
Figure 18: Temperature measurement location
Figure 20: Temperature measurement location
* The allowed maximum hot spot temperature is defined at 118℃ * The allowed maximum hot spot temperature is defined at 112℃
Q48SK12025(Standard) Output Current vs. Ambient Temperature and Air Velocity
@Vin = 48V (Transverse Orientation,With Heatspreader)
Q48SK12025(Standard) Output Current vs. Ambient Temperature and Air Velocity
@Vin = 48V (Transverse Orientation)
Output Current(A)
Output Current(A)
25
20
15
10
5
25
20
15
10
5
Natural
Convection
Natural
Convection
100LFM
200LFM
100LFM
200LFM
300LFM
400LFM
300LFM
400LFM
500LFM
600LFM
500LFM
600LFM
0
0
25
30
35
40
45
50
55
60
65
70
75
80
85
25
30
35
40
45
50
55
60
65
70
75
80
85
Ambient Temperature (℃)
Ambient Temperature (℃)
Figure 19: Output current vs. ambient temperature and air
velocity @Vin=48V(Transverse Orientation, without heat
spreader)
Figure 21: Output current vs. ambient temperature and air
velocity @Vin=48V(Transverse Orientation, with heat spreader)
DS_Q48SK12025_07012010
10
MECHANICAL DRAWING (WITH HEAT SPREADER)
* For modules with through-hole pins and the optional heat spreader, they are intended for wave soldering
assembly onto system boards; please do not subject such modules through reflow temperature profile.
DS_Q48SK12025_07012010
11
MECHANICAL DRAWING (WITHOUT HEAT SPREADER)
Pin No.
Name
Function
1
2
3
4
5
6
+Vin
Positive input voltage
ON/OFF
Case
-Vin
Remote ON/OFF
Optional
Negative input voltage
Negative output voltage
Positive output voltage
-Vout
+Vout
Pin Specification:
Pins 1-4
1.00mm (0.040”) diameter
1.50mm (0.059”) diameter
Pins 5 &6
All pins are copper with Tin plating.
DS_Q48SK12025_07012010
12
PART NUMBERING SYSTEM
PART NUMBERING SYSTEM
Q
48
S
K
120
Number of Product Output
Outputs Series
25
N
R
F
A
Form
Factor
Input
Output
ON/OFF
Logic
Pin
Option Code
Voltage
Voltage Current
Length
F- RoHS 6/6
(Lead Free)
Q - Quarter 48-36V~75V S - Single
Brick
K- QB high 120 - 12V 25 - 25A
N - Negative K - 0.110”
A - Std. Functions
without case pin
power
series
P - Positive
N - 0.146”
R - 0.170”
Space- RoHS5/6
H-with heat spreader
and case pin
N- with heat spreader
without case pin
MODEL LIST
MODEL NAME
Q48SK12025NRFA
Q48SK12025NRFH
Q48SK12025NRFN
Q48SK12025NNFN
INPUT
OUTPUT
EFF @ 100% LOAD
36V~75V
36V~75V
36V~75V
36V~75V
11A
11A
11A
11A
12V
12V
12V
12V
25A
25A
25A
25A
95.2%
95.2%
95.2%
95.2%
Default remote on/off logic is negative and pin length is 0.170”
For different remote on/off logic and pin length, please refer to part numbering system above or contact your local sales
* For modules with through-hole pins and the optional heat spreader, they are intended for wave soldering
assembly onto system boards; please do not subject such modules through reflow temperature profile.
CONTACT: www.delta.com.tw/dcdc
USA:
Telephone:
Europe:
Asia & the rest of world:
Telephone: +886 3 4526107
ext 6220~6224
Phone: +41 31 998 53 11
Fax: +41 31 998 53 53
Email: DCDC@delta-es.com
East Coast: (888) 335 8201
West Coast: (888) 335 8208
Fax: (978) 656 3964
Email: DCDC@delta-corp.com
Fax: +886 3 4513485
Email: DCDC@delta.com.tw
WARRANTY
Delta offers a two (2) year limited warranty. Complete warranty information is listed on our web site or is available upon
request from Delta.
Information furnished by Delta is believed to be accurate and reliable. However, no responsibility is assumed by Delta for its
use, nor for any infringements of patents or other rights of third parties, which may result from its use. No license is granted
by implication or otherwise under any patent or patent rights of Delta. Delta reserves the right to revise these specifications
at any time, without notice.
DS_Q48SK12025_07012010
13
相关型号:
Q48SK12025PKFA
Delphi Series Q48SK, Quarter Brick Family DC/DC Power Modules: 36~75V in, 12V/25A out, 300W
DELTA
Q48SK12025PKFH
Delphi Series Q48SK, Quarter Brick Family DC/DC Power Modules: 36~75V in, 12V/25A out, 300W
DELTA
Q48SK12025PKFN
Delphi Series Q48SK, Quarter Brick Family DC/DC Power Modules: 36~75V in, 12V/25A out, 300W
DELTA
Q48SK12025PNFA
Delphi Series Q48SK, Quarter Brick Family DC/DC Power Modules: 36~75V in, 12V/25A out, 300W
DELTA
Q48SK12025PNFH
Delphi Series Q48SK, Quarter Brick Family DC/DC Power Modules: 36~75V in, 12V/25A out, 300W
DELTA
Q48SK12025PNFN
Delphi Series Q48SK, Quarter Brick Family DC/DC Power Modules: 36~75V in, 12V/25A out, 300W
DELTA
Q48SK12025PRFA
Delphi Series Q48SK, Quarter Brick Family DC/DC Power Modules: 36~75V in, 12V/25A out, 300W
DELTA
Q48SK12025PRFH
Delphi Series Q48SK, Quarter Brick Family DC/DC Power Modules: 36~75V in, 12V/25A out, 300W
DELTA
Q48SK12025PRFN
Delphi Series Q48SK, Quarter Brick Family DC/DC Power Modules: 36~75V in, 12V/25A out, 300W
DELTA
©2020 ICPDF网 联系我们和版权申明