IW1816-20-SO7 [DIALOG]
Off-Line Digital Green-Mode PWM Controller Integrated;
| 型号： | IW1816-20-SO7 |
| 厂家： | 
Dialog Semiconductor |
| 描述： | Off-Line Digital Green-Mode PWM Controller Integrated |
| 文件： | 总18页 (文件大小：865K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
iW1816
Off-Line Digital Green-Mode PWM Controller
Integrated with Power BJT and OTP
1 Description
The iW1816 is a high performance AC/DC power supply control device which uses digital control technology to build
peak current mode PWM flyback power supplies. This device includes an internal power BJT and operates in quasi-
resonant mode to provide high efficiency along with a number of key built-in protection features while minimizing the
external component count, simplifying EMI design, and lowering the total bill of material cost. The iW1816 removes the
need for secondary feedback circuit while achieving excellent line and load regulation. It also eliminates the need for
loop compensation components while maintaining stability in all operating conditions. The pulse-by-pulse waveform
analysis allows for a loop response that is much faster than traditional solutions, resulting in improved dynamic load
response for both one-time and repetitive load transients. The built-in power limit function enables optimized transformer
design in universal off-line applications and allows for a wide input voltage range.
Dialog’s innovative proprietary technology ensures that power supplies built with the iW1816 can achieve highest
average efficiency, lowest standby power consumption, and fast smooth startup with a wide range of output voltage (5V,
12V and above) and capacitive loads (from 330μF to 6,000μF).
2 Features
● PrimAccurateTM primary-side feedback eliminates
● Quasi-resonant operation for highest overall efficiency
EZ-EMI® design easily meets global EMI standards
opto-isolators and simplifies design
●
● Internal 800-V bipolar junction transistor (BJT)
● Very tight constant voltage and constant current
regulation with primary-side-only feedback
● Adaptively controlled soft start-up enables fast and
smooth start-up for a wide range of output voltage (5V,
12V and above) and capacitve loads up to 6,000μF
● No external compensation components required
● Built-in single-point fault protections against output
short circuit, output over-voltage, and current-sense-
resistor short-circuit faults
● 64kHz PWM switching frequency
● No-load power consumption < 30mW at 230VAC with
typical application circuit
● Built-in over-temperature protection (OTP)
● Fast dynamic load response for both one-time and
● No audible noise over entire operating range
repetitive load transients
● Adaptive multi-mode PWM/PFM control improves
efficiency
3 Applications
● Low-power AC/DC power supply for smart meters,
motor control, home appliances, networking devices
and industrial applications
● Linear AC/DC replacement
30-Jun-2016
Datasheet
Rev. 1.0
www.dialog-semiconductor.com
1 of 18
© 2016 Dialog Semiconductor
iW1816
Off-Line Digital Green-Mode PWM Controller
Integrated with Power BJT and OTP
L
V
OUT
+
+
GND
N
U1
iW1816
1
2
8
7
C
C
E
I
SENSE
V
6
5
SENSE
GND
4
V
CC
Figure 3.1 : iW1816 Typical Application Circuit
WARNING:
The iW1816 is intended for high voltage AC/DC offline applications. Contact with live high voltage offline
circuits or improper use of components may cause lethal or life threatening injuries or property damage. Only
qualified professionals with safety training and proper precaution should operate with high voltage offline
circuits.
iW1816 Output Power Table at Universal Input (85VAC–264VAC)
Condition
Adapter1
Open Frame2
Output Power (W)
4.0
5.0
Notes:
1. Maximum practical continuous output power measured at enclosure internal ambient temperature of 60°C and device emitter pin
(pin 8) temperature of ≤ 90°C (adapter is placed in a non-ventilated environment).
2. Maximum practical continuous output power measured at open frame ambient temperature of 50°C and device emitter pin
(pin 8) temperature of ≤ 90°C while minimum bulk capacitor voltage is kept above 90V and no special heatsinking is used (test
unit is placed in a non-ventilated environment).
3. The output power can vary depending on the power supply system designs and operating conditions. See Section 10.14 for
more details.
30-Jun-2016
Datasheet
Rev. 1.0
www.dialog-semiconductor.com
2 of 18
© 2016 Dialog Semiconductor
iW1816
Off-Line Digital Green-Mode PWM Controller
Integrated with Power BJT and OTP
4 Pinout Description
iW1816
E
1
2
C
C
8
7
6
5
I
SENSE
V
SENSE
GND
4
V
CC
Figure 4.1 : 7-Pin SOIC Package
Pin Description
Pin No.
Pin Name
Type
C
BJT Collector Collector of internal bipolar junction transistor (BJT).
BJT Collector Collector of internal BJT.
1
C
VCC
2
4
5
6
7
8
Power Input
Ground
Power supply for control logic.
Ground.
GND
VSENSE
ISENSE
E
Analog Input Auxiliary voltage sense (used for primary-side regulation).
Primary current sense. Used for cycle-by-cycle peak current control and
current limit.
Analog Input
Emitter of internal BJT (pin 7 and pin 8 must be shorted externally on the
BJT Emitter
PCB).
30-Jun-2016
Datasheet
Rev. 1.0
www.dialog-semiconductor.com
3 of 18
© 2016 Dialog Semiconductor
iW1816
Off-Line Digital Green-Mode PWM Controller
Integrated with Power BJT and OTP
5 Absolute Maximum Ratings
Absolute maximum ratings are the parameter values or ranges which can cause permanent damage if exceeded. For
maximum safe operating conditions, refer to Electrical Characteristics in Section 7.0. (TA = 25°C, unless otherwise
noted). Proper design precautions must be made to ensure that the internal die junction temperature of the iW1816
does not exceed 150°C. Otherwise permanent damage to the device may occur.
Parameter
Symbol
VCC
Value
-0.3 to 18
20
Units
V
DC supply voltage range (pin 4, ICC = 20mA max)
Continuous DC supply current at VCC pin (VCC = 15V)
VSENSE input (pin 6, IVsense ≤ 10mA)
ISENSE input (pin 7)
ICC
mA
V
-0.7 to 4.0
-0.3 to 4.0
±2,000
±100
V
ESD rating per JEDEC JESD22-A114
Latch-up test per JESD78A
V
mA
Collector-Emitter breakdown voltage
(Emitter and base shorted together; IC = 1mA, REB = 0Ω)
VCES
800
V
Collector current1
IC
1.5
3
A
A
Collector peak current1 (t < 1ms)
ICM
p
Maximum junction temperature
TJMAX
TSTG
TLEAD
150
°C
°C
°C
Storage temperature
-55 to 150
260
Lead temperature during IR reflow for ≤ 15 seconds
Notes:
Note 1: Limited by maximum junction temperature.
6 Thermal Characteristics
Parameter
Symbol
θJA
Value
132
71
Units
°C/W
°C/W
°C/W
°C
Thermal Resistance Junction-to-Ambient1
Thermal Resistance Junction-to-GND pin (pin 5)2
Thermal Resistance Junction-to-Collector pin (pin 1)2
Thermal Shutdown Threshold3
ψJB
ψJ-BJT
49
TSD
150
100
Thermal Shutdown Recovery3
TSD-R
°C
Notes:
1. θJA is measured in a one-cubic-foot natural convection chambe.
2. ψJB [Psi Junction to Board] provides an estimation of the die junction temperature relative to the PCB [Board] surface
temperature. ψJ-BJT [Psi Junction to Collector pin] provides an estimation of the die junction temperature relative to the collector
pin [internal BJT Collector] surface temperature. ψJB is measured at the ground pin (pin 5) without using any thermal adhesives..
See Section 10.14 for more information.
3. These parameters are typical and they are guaranteed by design.
30-Jun-2016
Datasheet
Rev. 1.0
www.dialog-semiconductor.com
4 of 18
© 2016 Dialog Semiconductor
iW1816
Off-Line Digital Green-Mode PWM Controller
Integrated with Power BJT and OTP
7 Electrical Characteristics
VCC = 12V, -40°C ≤ TA ≤ 85°C
Parameter
Symbol
Test Conditions
Min
Typ
Max
Unit
VSENSE SECTION (Pin 6)
Input leakage current
IBVS
VSENSE = 2V
1
V
V
V
Nominal voltage threshold
VSENSE(NOM) TA=25°C, negative edge
VSENSE(MAX) TA=25°C, negative edge
1.518
1.533
1.834
1.548
Output OVP threshold
ISENSE SECTION (Pin 7)
Over-current threshold
VOCP
1.11
1.15
1.0
1.19
V
V
ISENSE regulation upper limit
(Note 1)
VIPK(HIGH)
ISENSE regulation lower limit
(Note 1)
VIPK(LOW)
0.23
V
Input leakage current
ILK
ISENSE = 1.0V
1
μA
VCC SECTION (Pin 4)
Maximum operating voltage
(Note 1)
VCC(MAX)
VCC(ST)
16
12.0
4.2
V
V
V
Start-up threshold
VCC rising
VCC falling
10.0
3.8
11.0
4.0
Under-voltage lockout
threshold
VCC(UVL)
Start-up current
IIN(ST)
ICCQ
VCC = 10V
1.0
1.7
2.7
3.0
4.0
μA
Quiescent current
No IB current
mA
Zener current = 5mA
Zener breakdown voltage
VZB
18.5
19.5
20.5
V
TA=25°C
BJT Section (Pin 1, Pin 2, and Pin 8)
Collector cutoff current
ICB0
VCB = 800V, IE = 0A
0.01
0.01
0.02
mA
mA
VCE = 800V, REB = 0Ω TA = 25°C
VCE = 800V, REB = 0Ω TA = 100°C
Collector-emitter cutoff current
DC Current Gain (Note 2)
ICES
VCE = 500V, REB = 0Ω TA = 25°C
VCE = 5V, IC = 0.2A
0.005
40
15
10
10
VCE = 5V, IC = 0.3A
30
hFE
VCE = 5V, IC = 1mA
30-Jun-2016
Datasheet
Rev. 1.0
www.dialog-semiconductor.com
5 of 18
© 2016 Dialog Semiconductor
iW1816
Off-Line Digital Green-Mode PWM Controller
Integrated with Power BJT and OTP
VCC = 12V, -40°C ≤ TA ≤ 85°C, unless otherwise specified
6 Electrical Characteristics (continued)
Parameter
Symbol
Test Conditions
IC = 0.1mA
Min
Typ
Max
Unit
Collector-Base breakdown voltage
VCB0
800
V
Collector-Emitter breakdown voltage
(Emitter and base shorted together)
VCES
IC = 1mA, REB = 0Ω
800
500
V
Collector-Emitter sustain voltage
Collector-Emitter saturation voltage2
PWM switching frequency3
VCEO(SUS)
VCE(SAT)
fSW
IC = 1mA, LM = 25mH
IC = 0.1A, IB = 0.02A
> 50% load
V
V
0.1
0.3
64
kHz
Notes:
1. These parameters are not 100% tested. They are guaranteed by design and characterization.
2. Impulse tP ≤ 300μs, duty cycle ≤ 2%.
3. Operating frequency varies based on the load conditions, see Section 10.6 for more details.
30-Jun-2016
Datasheet
Rev. 1.0
www.dialog-semiconductor.com
6 of 18
© 2016 Dialog Semiconductor
iW1816
Off-Line Digital Green-Mode PWM Controller
Integrated with Power BJT and OTP
8 Typical Performance Characteristics
12.0
11.6
11.2
10.8
10.4
10.0
4.58
4.54
4.50
4.46
4.42
4.38
-50
-25
0
25
50
75
100 125 150
-50
-25
0
25
50
75
100 125 150
Ambient Temperature (ºC)
Ambient Temperature (ºC)
Figure 8.1 : VCC UVLO vs. Temperature
Figure 8.2 : Start-Up Threshold vs. Temperature
2.010
70
2.006
2.002
1.998
1.994
1.990
67
64
61
58
55
-50
-25
0
25
50
75
100 125 150
-50
-25
0
25
50
75
100 125 150
Ambient Temperature (ºC)
Ambient Temperature (ºC)
Figure 8.3 : Switching Frequency vs. Temperature
Figure 8.4 : Internal Reference vs. Temperature
2.5
2.0
1.5
1.0
0.5
0.0
0.0
3.0
6.0
9.0
12.0
V
CC
(V)
Figure 8.5 : VCC vs. VCC Supply Start-up Current
Notes:
1. Operating frequency varies based on the load conditions, see Section 10.6 for more details.
30-Jun-2016
Datasheet
Rev. 1.0
www.dialog-semiconductor.com
7 of 18
© 2016 Dialog Semiconductor
iW1816
Off-Line Digital Green-Mode PWM Controller
Integrated with Power BJT and OTP
9 Functional Block Diagram
V
4
CC
Start-up
ENABLE
BJT
C (collector)
C (collector)
1
2
Base
Drive
Digital
Logic
Control
V
Signal
Conditioning
FB
V
6
5
SENSE
Thermal
Shutdown
E (emitter)
8
OCP
1.15V
DAC
I
I
PK
V
7
SENSE
SENSE(NOM)
= 1.533V
GND
V
IPK
0.23V ~ 1.0V
Figure 9.1 : iW1816 Functional Block Diagram
30-Jun-2016
Datasheet
Rev. 1.0
www.dialog-semiconductor.com
8 of 18
© 2016 Dialog Semiconductor
iW1816
Off-Line Digital Green-Mode PWM Controller
Integrated with Power BJT and OTP
10 Theory of Operation
The iW1816 is a digital controller integrated with a power BJT. It uses a proprietary primary-side control technology to
eliminate the opto-isolated feedback and secondary regulation circuits required in traditional designs. This provides a
low-cost solution for low power AC/DC adapters. The core PWM processor uses fixed-frequency Discontinuous
Conduction Mode (DCM) operation at higher power levels and switches to variable frequency operation at light loads
to maximize efficiency. Furthermore, Dialog’s digital control technology enables fast dynamic response, tight output
regulation, and full-featured circuit protection with
primary-side control.
The block diagram in Figure 9.1 shows the digital logic control block generates the switching on-time and
off-time information based on the output voltage and current feedback signal and provides instructions to dynamically
control the internal BJT base current. The ISENSE is an analog input configured to sense the primary current in a voltage
form. In order to achieve the peak current mode control and cycle-by-cycle current limit, the VIPK sets the threshold for
the ISENSE to compare with, and it varies in the range of
0.23V (typical) and 1.00V (typical) under different line and load conditions. The system loop is automatically compensated
internally by a digital error amplifier. Adequate system phase margin and gain margin are guaranteed by design and
no external analog components are required for loop compensation. The iW1816 uses an advanced digital control
algorithm to reduce system design time and increase reliability.
Furthermore, accurate secondary constant-current operation is achieved without the need for any secondary-side
sense and control circuits.
The iW1816 uses adaptive multi-mode PWM/PFM control to dynamically change the BJT switching frequency for
efficiency, EMI, and power consumption optimization. In addition, it achieves unique BJT quasi-resonant switching
to further improve efficiency and reduce EMI. The built-in single-point fault protection features include over-voltage
protection (OVP), output-short-circuit protection (SCP),
over-current protection (OCP), and ISENSE fault detection.
Dialog’s digital control scheme is specifically designed to address the challenges and trade-offs of power conversion
design. This innovative technology is ideal for balancing new regulatory requirements for green mode operation with
more practical design considerations such as the lowest possible cost, smallest size and high performance output
control.
10.1 Pin Detail
Pin 1 and Pin 2 - C
Collector pin of the internal power BJT.
Pin 4 – VCC
Power supply for the controller during normal operation. The controller will start up when VCC reaches 11.0V (typical)
and will shut-down when the VCC voltage is 4.0V (typical). A decoupling capacitor should be connected between the
VCC pin and GND.
Pin 5 – GND
Ground.
Pin 6 – VSENSE
Sense signal input from auxiliary winding. This provides the secondary voltage feedback used for output regulation.
30-Jun-2016
Datasheet
Rev. 1.0
www.dialog-semiconductor.com
9 of 18
© 2016 Dialog Semiconductor
iW1816
Off-Line Digital Green-Mode PWM Controller
Integrated with Power BJT and OTP
Pin 7 – ISENSE
Primary current sense. It is used for cycle-by-cycle peak current control and limit.
Pin 8 – E
Emitter pin of the internal power BJT. This pin must be shorted to pin 7 (the ISENSE pin).
10.2 Adaptively Controlled Soft Start-up
The iW1816 features an innovative proprietary soft-start scheme to achieve fast yet smooth start-up with a wide
range of output loads, including capacitive loads typically from 330μF to 6,000μF, and for output voltage covering
typically from 5V to 12V. Prior to start-up, the VCC pin is charged typically through start-up resistors. When VCC bypass
capacitor is fully charged to a voltage higher than the start-up threshold VCC(ST), the ENABLE signal becomes active to
enable the control logic, and the iW1816 begins to perform initial over-temperature protection check. When the internal
die junction temperature is below 100°C, the iW1816 commences soft-start function. During the soft-start process,
the primary-side peak current is limited cycle by cycle by the IPEAK comparator. The whole soft-start process can break
down into several stages based on the output voltage levels, which is indirectly sensed by VSENSE signal at the primary
side. At different stages, the iW1816 adaptively controls the switching frequency and primary-side peak current
such that the output voltage can always build up very fast at the early stages and smoothly transition to the desired
regulation voltage at the final stage, regardless of any capacitive and resistive loads that the applications may incur.
With a lowest system cost, this adaptively controlled soft start-up feature makes the iW1816 ideal in applications with
12V output or large capacitive loads such as home appliances and ADSL modems.
If at any time the VCC voltage drops below VCC(UVL) threshold then all the digital logic is reset. At this time the ENABLE
signal becomes low and the VCC capacitor is charged up again towards the start-up threshold.
Start-up
Sequencing
V
CC(ST)
V
CC
ENABLE
Figure 10.1 : Start-up Sequencing Diagram
10.3 Understanding Primary Feedback
Figure 10.2 illustrates a simplified flyback converter. When the switch Q1 conducts during tON(t), the current ig(t)
is directly drawn from the rectified sinusoid vg(t). The energy EG(t) is stored in the magnetizing inductance LM. The
rectifying diode D1 is reverse biased and the load current IO is supplied by the secondary capacitor CO. When Q1 turns
off, D1 conducts and the stored energy Eg(t) is delivered to the output.
30-Jun-2016
Datasheet
Rev. 1.0
www.dialog-semiconductor.com
10 of 18
© 2016 Dialog Semiconductor
iW1816
Off-Line Digital Green-Mode PWM Controller
Integrated with Power BJT and OTP
i (t)
i (t)
i (t)
d
in
g
N:1
V
+
O
+
D1
V
I
O
C
O
v (t)
g
v (t)
AUX
in
–
Q1
T (t)
S
Figure 10.2 : Simplified Flyback Converter
In order to tightly regulate the output voltage, accurate information about the output voltage and load current must
be accurately conveyed. In the DCM flyback converter, this information can be read via the auxiliary winding or
the primary magnetizing inductance (LM). During the Q1 on-time, the load current is supplied from the output filter
capacitor CO. The voltage across LM is vg(t), if the voltage dropped across Q1 is zero. The current in Q1 ramps up
linearly at a rate of:
dig
t
vg
t
( )
( )
LM
=
(10.1)
(10.2)
dt
At the end of on-time, the current ramps up to:
vg t ×t
( )
ON
ig _ peak t =
( )
LM
This current represents a stored energy of:
LM
2
Eg
=
×ig _ peak t
( )
(10.3)
2
When Q1 turns off at tO, ig(t) in LM forces a reversal of polarities on all windings. Ignoring the communication-time
caused by the leakage inductance LK at the instant of turn-off tO, the primary current transfers to the secondary at a
peak amplitude of:
NP
id t =
( )
×ig _ peak t
( )
(10.4)
NS
Assuming the secondary winding is master, and the auxiliary winding is slave,
N
AUX
V
= V x
O
1
AUX
N
S
V
AUX
0V
N
AUX
V
= -V
x
2
AUX
IN
N
P
30-Jun-2016
Datasheet
Rev. 1.0
Figure 10.3 : Auxiliary Voltage Waveforms
www.dialog-semiconductor.com
11 of 18
© 2016 Dialog Semiconductor
iW1816
Off-Line Digital Green-Mode PWM Controller
Integrated with Power BJT and OTP
The auxiliary voltage is given by:
NAUX
VAUX
=
V + ∆V
(
O
)
(10.5)
NS
and reflects the output voltage as shown in Figure 10.3.
The voltage at the load differs from the secondary voltage by a diode drop and IR losses. Therefore, if the secondary
voltage is always read at a constant secondary current, the difference between the output voltage and the secondary
voltage is a fixed ΔV. Furthermore, if the voltage can be read when the secondary current is small, ΔV is also small.
With the iW1816, ΔV can be ignored.
The real-time waveform analyzer in the iW1816 reads this information cycle by cycle. The part then generates a
feedback voltage VFB. The VFB signal accurately represents the output voltage under most circumstances and is used
to regulate the output voltage.
10.4 Constant Voltage Operation
After soft-start is completed, the digital control block measures the output conditions. It determines the output power
levels and adjusts the control system according to either a light or a heavy load. If this is in the normal range, the
device operates in the Constant Voltage (CV) mode, and changes the pulse width (TON) and off-time (TOFF) in order to
meet the output voltage regulation requirements.
If no voltage is detected on VSENSE, it is assumed that the auxiliary winding of the transformer is either open or shorted
and the iW1816 shuts down.
10.5 Constant Current Operation
At overload condition, the iW1816 enters constant current (CC) mode to limit the output current on cycle-by-cycle
basis. During this mode of operation the output current is limited to a constant level regardless of the output voltage,
while avoiding continuous conduction mode operation. In case of very heavy loading, when the output voltage is low
enough, the iW1816 shuts down.
To achieve this regulation the iW1816 senses the load current indirectly through the primary current. The primary
current is detected by the ISENSE pin through a resistor from the BJT emitter to ground.
CV mode
V
NOM
I
OUT(CC)
Output Current
Figure 10.4 : Power Envelope
30-Jun-2016
Datasheet
Rev. 1.0
www.dialog-semiconductor.com
12 of 18
© 2016 Dialog Semiconductor
iW1816
Off-Line Digital Green-Mode PWM Controller
Integrated with Power BJT and OTP
10.6 Multi-Mode PWM/PFM Control and Quasi-Resonant Switching
The iW1816 uses a proprietary adaptive multi-mode PWM/PFM control to dramatically improve the light-load efficiency
and thus the overall average efficiency.
During the constant voltage (CV) operation, the iW1816 normally operates in a pulse-width-modulation (PWM) mode
in heavy load conditions. In the PWM mode, the switching frequency keeps around constant. As the output load IOUT is
reduced, the on-time tON is decreased, and the controller adaptively transitions to a pulse-frequency-modulation (PFM)
mode. When in the PFM mode, the BJT is turned on for a set duration under a given instantaneous rectified AC input
voltage, but its off-time is modulated by the load current. With a decreasing load current, the off-time increases and
thus the switching frequency decreases.
When the switching frequency approaches to human ear audio band, the iW1816 transitions to a second level of
PWM mode, namely Deep PWM mode (DPWM). In the DPWM mode, the switching frequency keeps around 22kHz in
order to avoid audible noise. As the load current is further reduced, the iW1816 transitions to a second level of PFM
mode, namely Deep PFM mode (DPFM), which can reduce the switching frequency to a very low level. Although the
switching frequency drops across the audible frequency range in the DPFM mode, the output current in the power
converter has reduced to an insignificant level in the DPWM mode before transitioning to the DPFM mode. Therefore
the power converter practically produces no audible noise, while achieving high efficiency across varying load
conditions.
As the load current reduces to a very low or no-load condition, the iW1816 transitions from the DPFM to the third level
of PWM mode, namely Deep-Deep PWM mode (DDPWM), where the switching frequency is fixed at around 1.9kHz.
The iW1816 also incorporates a unique proprietary quasi-resonant switching scheme that achieves valley-mode turn-
on for every PWM/PFM switching cycle, in all PFM and PWM modes, and in both CV and CC operations. This unique
feature greatly reduces the switching loss and dv/dt across the entire operating range of the power supply. Due to
the nature of quasi-resonant switching, the actual switching frequency can vary slightly cycle by cycle, providing the
additional benefit of reducing EMI. Together these innovative digital control architecture and algorithms enable the
iW1816 to achieve the highest overall efficiency and lowest EMI, without causing audible noise over entire operating
range.
10.7 Less Than 30mW No-Load Power with Fast Load Transient Response
The iW1816 features the distinctive DDPWM control at no-load conditions to help achieve very low no-load power
consumption (< 30mW for typical applications) and meanwhile to ensure fast dynamic load response. The power
supply system designs including the pre-load resistor selection should ensure the power supply can stably operate
in the DDPWM mode at the steady-state no-load condition. If the pre-load resistor is too small, the no-load power
consumption will increase; on the other hand, if it is too large, the output voltage may increase and even cause over-
voltage since the switching frequency is fixed at around 1.9kHz. For typical designs with 12V output, the pre-load
resistor is in the range of 25kW to 50kW.
Aside from the appropriate use of pre-load resistor, the iW1816 enjoys a few other features to bring down no-load
power consumption as well. First, the iW1816 implements an intelligent low-power management technique that
achieves ultra-low chip operating current at the no-load, typically less than 400µA. Second, the use of the power
switch of BJT instead of MOSFET requires a lower driving voltage, enabling a low UVLO threshold as low as 4.0V
(typical). The power supply system design can fully utilize this low UVLO feature to have a low Vcc voltage at the
no-load operation in order to minimize the no-load power. In addition, the ultra-low start-up current during the
ramp-up of VCC towards the start-up threshold VCC(ST) (see Figure 8.5), allows for the use of high resistance start-
up resistors to minimize their loss while still retaining reasonable turn-on time. All together these features ensure
that with the lowest system cost, power supplies built with the iW1816 can achieve less than 30mW no-load power
consumption at 230 VAC input and very tight constant voltage and constant current regulation over the entire operating
range including the no-load operation.
30-Jun-2016
Datasheet
Rev. 1.0
www.dialog-semiconductor.com
13 of 18
© 2016 Dialog Semiconductor
iW1816
Off-Line Digital Green-Mode PWM Controller
Integrated with Power BJT and OTP
While achieving super-low no-load power consumption, the iW1816 implements innovative proprietary digital control
technology to intelligently detect any load transient events, and achieve fast dynamic load response for both one-
time and repetitive load transients. In particular, for load transients that are demanded in some applications as from
absolutely no load to full load, the iW1816 can still guarantee a fast enough response to meet the most stringent
requirements, with the no-load operating frequency designed at around 1.9kHz.
10.8 Variable Frequency Operation Mode
During each of the switching cycles, the falling edge of VSENSE is checked. If the falling edge of VSENSE is not detected,
the off-time is extended until the falling edge of VSENSE is detected. The maximum transformer reset time allowed is
125μs. When the transformer reset time reaches 125μs, the iW1816 shuts off.
10.9 Internal Loop Compensation
The iW1816 incorporates an internal Digital Error Amplifier with no requirement for external loop compensation. For
a typical power supply design, the loop stability is guaranteed to provide at least 45 degrees of phase margin and
-20dB of gain margin.
10.10 Voltage Protection Features
The secondary maximum output DC voltage is limited by the iW1816. When the VSENSE signal exceeds the output
OVP threshold at point 1 (as shown in Figure 10.3), the iW1816 shuts down.
The iW1816 protects against input line under-voltage by setting a maximum TON time. Since output power is
proportional to the squared VINTON product, for a given output power, the TON increases as the VIN decreases. Thus by
knowing when the maximum TON time occurs, the iW1816 detects that the minimum VIN is reached, and then it shuts
down. The maximum tON limit is set to 15.6μs. Also, the iW1816 monitors the voltage on the VCC pin and when the
voltage on this pin is below UVLO threshold the IC shuts down immediately.
When any of these faults is met the IC remains biased to discharge the VCC supply. Once VCC drops below the UVLO
threshold, the controller resets itself and then initiates a new soft-start cycle. The controller continues attempting start-
up until the fault condition is removed.
10.11 PCL, OCP and SRS Protection
The peak-current limit (PCL), over-current protection (OCP) and sense-resistor short protection (SRSP) are built-in
features in the iW1816. With the ISENSE pin the iW1816 is able to monitor the peak primary current. This allows for
cycle-by-cycle peak current control and limit. When the peak primary current multiplied by the ISENSE resistor is greater
than 1.15V, over-current protection (OCP) is detected and the IC immediately turns off the base driver until the next
cycle. The output driver sends out a switching pulse in the next cycle, and the switching pulse continues if the OCP
threshold is not reached; or, the switching pulse turns off again if the OCP threshold is reached. If the OCP occurs for
several consecutive switching cycles, the iW1816 shuts down.
If the ISENSE resistor is shorted, there is a potential danger that the over-current condition is not detected. Thus, the
IC is designed to detect this sense-resistor-short fault after start-up and immediate shutdown. The VCC is discharged
since the IC remains biased. Once the VCC drops below the UVLO threshold, the controller resets itself and then
initiates a new soft-start cycle. The controller continues attempting to start up, but does not fully start up until the fault
condition is removed.
10.12 Dynamic Base Current Control
An important feature of the iW1816 is that it directly drives an internal BJT switching device with dynamic base current
control to optimize performance. The BJT base current ranges from 10mA to 31mA, and is dynamically controlled
according to the power supply load change. The higher the output power, the higher the base current. Specifically, the
base current is related to VIPK, as shown in Figure 10.5.
30-Jun-2016
Datasheet
Rev. 1.0
www.dialog-semiconductor.com
14 of 18
© 2016 Dialog Semiconductor
iW1816
Off-Line Digital Green-Mode PWM Controller
Integrated with Power BJT and OTP
35
30
25
20
15
10
5
0
0
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1
(V)
VIPK
Figure 10.5 : Base Drive Current vs. VIPK
10.13 Internal Over-Temperature Protection
The iW1816 features an internal over-temperature protection (OTP), which will shut down the device if the internal die
junction temperature reaches above 150°C (typical). The device will be kept off until the junction temperature drops
below 100°C (typical), when the device initiates a new soft-start process to build up the output voltage.
10.14 Thermal Design
The iW1816 may be installed inside a small enclosure, where space and air volumes are constrained. Under these
circumstances θJA (thermal resistance, junction-to-ambient) measurements do not provide useful information for this
type of application. Hence we have also provided ψJB which estimates the increase in die junction temperature relative
to the PCB surface temperature. Figure 10.6 shows the PCB surface temperature is measured at the IC’s GND pin pad.
ψJ-BJT
ψJB
J
J
B
BJT collector
PCB Top Copper Trace
GND pin
Collector pin
T
J
IC Die
Printed Circuit Board
Note: For illustrative purposes only does not represent a correct pinout or size of chip
Figure 10.6 : Thermal Resistance
The actual IC power dissipation is related to the power supply application circuit, component selection and operation
conditions. The maximum IC power dissipation should be used to estimate the maximum junction temperature. For a
typical 3-W power supply, the power dissipation can be around 500mW.
The output power table in Section 3.0 recommends maximum practical continuous output power level be achieved
under the following conditions:
● Typical 5V-output power supply designs with a Schottky rectifier diode
● Ambient temperature of 50°C for open frame and adapter enclosure internal temperature of 60°C in a
non-ventilated environment
● AC Input voltage is 85VAC at 47Hz
30-Jun-2016
Datasheet
Rev. 1.0
www.dialog-semiconductor.com
15 of 18
© 2016 Dialog Semiconductor
iW1816
Off-Line Digital Green-Mode PWM Controller
Integrated with Power BJT and OTP
● Minimum bulk capacitor voltage is 90V for open frame and 70V for adapter
● The iW1816 device is mounted on PCB with no special enhancement for heatsinking and the emitter pin
temperature is kept below 90°C
Under a given power dissipation, reducing the GND, emitter, and collector pin temperature reduces the junction
temperature. Generally, increasing the PCB area and associated amount of copper trace reduces the junction
temperature. In particular, the power BJT is a power source and therefore the PCB plating area attached to the two
collector pins and the emitter pin can be reasonably large to gain the thermal benefits without violating the high voltage
creepage requirements if higher output power is desired. Higher output power is also achievable if bulk capacitor
voltage is higher, design is for high line only, design components temperature restriction limit is higher, ambient
temperature is lower, or extra metal piece/heat spreader is attached to related pins or package.
30-Jun-2016
Datasheet
Rev. 1.0
www.dialog-semiconductor.com
16 of 18
© 2016 Dialog Semiconductor
iW1816
Off-Line Digital Green-Mode PWM Controller
Integrated with Power BJT and OTP
11 Physical Dimensions
7-Lead Small Outline (SOIC) Package
D
Inches
Millimeters
MIN
0.060
A1 0.004
MAX
0.068
0.008
0.018
0.010
0.197
0.157
MIN
1.52
0.10
0.36
0.18
4.78
3.81
MAX
1.73
0.20
0.46
0.25
5.00
3.99
A
5
4
8
1
E
H
B
C
D
E
e
0.014
0.007
0.188
0.150
e
h x 45°
0.050 BSC
1.270 BSC
A1
H
h
0.230
0.010
0.023
0°
0.244
0.016
0.029
8°
5.84
0.25
0.58
6.20
0.41
0.74
A
L
α
L
B
SEATING
PLANE
C
α
COPLANARITY
0.10 (0.004)
Compliant to JEDEC Standard MS12F
Controlling dimensions are in inches; millimeter dimensions are for reference only
This product is RoHS compliant and Halide free.
Soldering Temperature Resistance:
[a] Package is IPC/JEDEC Std 020D Moisture Sensitivity Level 1
[b] Package exceeds JEDEC Std No. 22-A111 for Solder Immersion Resistance; package can withstand
10 s immersion < 270˚C
Dimension D does not include mold flash, protrusions or gate burrs. Mold flash, protrusions or gate burrs shall
not exceed 0.15 mm per end. Dimension E1 does not include interlead flash or protrusion. Interlead flash or
protrusion shall not exceed 0.25 mm per side.
The package top may be smaller than the package bottom. Dimensions D and E1 are determined at the
outermost extremes of the plastic bocy exclusive of mold flash, tie bar burrs, gate burrs and interlead flash, but
including any mismatch between the top and bottom of the plastic body.
12 Ordering Information
Part No.
Package
Description
iW1816-20-SO7
SOIC-7
Tape & Reel1
Note 1: Tape and reel packing quantity is 2,500/reel. Minimum ordering quantity is 2,500.
30-Jun-2016
Datasheet
Rev. 1.0
www.dialog-semiconductor.com
17 of 18
© 2016 Dialog Semiconductor
iW1816
Off-Line Digital Green-Mode PWM Controller
Integrated with Power BJT and OTP
Disclaimer
Information in this document is believed to be accurate and reliable. However, Dialog Semiconductor does not give any representations or
warranties, expressed or implied, as to the accuracy or completeness of such information. Dialog Semiconductor furthermore takes no responsibility
whatsoever for the content in this document if provided by any information source outside of Dialog Semiconductor.
Dialog Semiconductor reserves the right to change without notice the information published in this document, including without limitation the
specification and the design of the related semiconductor products, software and applications.
Applications, software, and semiconductor products described in this document are for illustrative purposes only. Dialog Semiconductor makes no
representation or warranty that such applications, software and semiconductor products will be suitable for the specified use without further testing
or modification. Unless otherwise agreed in writing, such testing or modification is the sole responsibility of the customer and Dialog Semiconductor
excludes all liability in this respect.
Customer notes that nothing in this document may be construed as a license for customer to use the Dialog Semiconductor products, software and
applications referred to in this document. Such license must be separately sought by customer with Dialog Semiconductor.
All use of Dialog Semiconductor products, software and applications referred to in this document are subject to Dialog Semiconductor’s Standard
Terms and Conditions of Sale, available on the company website (www.dialog-semiconductor.com) unless otherwise stated.
Dialog and the Dialog logo are trademarks of Dialog Semiconductor plc or its subsidiaries. All other product or service names are the property of
their respective owners.
© 2016 Dialog Semiconductor. All rights reserved.
RoHS Compliance
Dialog Semiconductor’s suppliers certify that its products are in compliance with the requirements of Directive 2011/65/EU of the European
Parliament on the restriction of the use of certain hazardous substances in electrical and electronic equipment. RoHS certificates from our suppliers
are available on request.
Contacting Dialog Semiconductor
UUnited Kingdom (Headquarters)
Dialog Semiconductor (UK) LTD
Phone: +44 1793 757700
North America
Singapore
Dialog Semiconductor Singapore
Phone: +65 64 8499 29
China (Shenzhen)
Dialog Semiconductor China
Phone: +86 755 2981 3669
Dialog Semiconductor Inc.
Phone: +1 408 845 8500
Germany
Japan
Hong Kong
China (Shanghai)
Dialog Semiconductor GmbH
Phone: +49 7021 805-0
Dialog Semiconductor K. K.
Phone: +81 3 5425 4567
Dialog Semiconductor Hong Kong
Phone: +852 3769 5200
Dialog Semiconductor China
Phone: +86 21 5424 9058
The Netherlands
Taiwan
Korea
Dialog Semiconductor B.V.
Phone: +31 73 640 8822
Dialog Semiconductor Taiwan
Phone: +886 281 786 222
Dialog Semiconductor Korea
Phone: +82 2 3469 8200
Email
Web site:
info_pcbg@diasemi.com
www.dialog-semiconductor.com
30-Jun-2016
Datasheet
Rev. 1.0
www.dialog-semiconductor.com
18 of 18
© 2016 Dialog Semiconductor
相关型号：
©2020 ICPDF网 联系我们和版权申明