AP3845GP [DIODES]
Switching Controller, 1A, 500kHz Switching Freq-Max, PDIP8, DIP-8;型号: | AP3845GP |
厂家: | DIODES INCORPORATED |
描述: | Switching Controller, 1A, 500kHz Switching Freq-Max, PDIP8, DIP-8 开关 光电二极管 |
文件: | 总13页 (文件大小:282K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Data Sheet
GREEN MODE PWM CONTROLLER
AP384XG
General Description
Features
The AP384XG is a Green Mode PWM controller. It is
specially designed for off-line AC-DC adapter and bat-
tery charger applications where both needs for low
standby power and high efficiency in normal operation
are required. In a well designed product, the AP384XG
is capable to allow the system consuming only 0.5W
power in standby mode.
·
Green Mode PWM Controller to Support the
"Blue Angel" Norm
·
·
·
·
·
·
·
Adjustable Skip Cycle Mode Operation
Low Start-up Current: 50μA (Typ.)
Low Standby Operating Current: 6mA
Internal Leading Edge Blanking
Adjustable Oscillator Frequency up to 500KHz
Totem Pole Output
In normal operation, the AP384XG features adjustable
frequency by using an external resistor and capacitor
Under Voltage Lock Out (UVLO)
combination. When output power falls below a given · Over-Temperature Protection
level, the IC automatically switches to the skip mode,
which works by skipping switching cycles. The
AP384XG also features low start-up and low standby
operating current for its special topology.
·
Pin to Pin Replacement for AZ384XA
Applications
The AP384XG provides accurate protection against
over-temperature, over-current and maximal output
power.
·
·
·
·
·
Off-line Converter
DC-DC Converter
DVD/STB Power Supply
Power Adapter
CRT Monitor Power Supply
The AP384XG is available in SOIC-8 and DIP-8
packages.
SOIC-8
DIP-8
Figure 1. Package Types of AP384XG
BCD Semiconductor Manufacturing Limited
Apr. 2007 Rev. 1. 3
1
Data Sheet
GREEN MODE PWM CONTROLLER
AP384XG
Pin Configuration
M/P Package
(SOIC-8/DIP-8)
COMP
FB
1
2
3
4
8
7
6
5
REF
VCC
CS
OUTPUT
GND
RT/CT
Figure 2. Pin Configuration of AP384XG
Pin Description
Pin Number Pin Name
Function
1
2
COMP
FB
This pin is the Error Amplifier output and is made available for loop compensation.
The inverting input of the Error Amplifier. It is normally connected to the switching power
supply output through an external resistor divider.
3
4
CS
It is used either for current sense (normal mode) or skip cycle level selection (standby mode).
RT/CT
The oscillator frequency and maximum output duty cycle are programmed by connecting
resistor RT to REF and capacitor CT to ground.
5
6
GND
The ground pin.
OUTPUT This output directly drives the gate of a power MOSFET. Peak currents up to 1.0 A are
sourced and sunk by this pin.
7
8
VCC
REF
The power supply pin.
This is the reference output. It provides charging current for capacitor CT through resistor RT.
BCD Semiconductor Manufacturing Limited
Apr. 2007 Rev. 1. 3
2
Data Sheet
GREEN MODE PWM CONTROLLER
AP384XG
Functional Block Diagram
7
VCC
34V
UVLO
8
6
5V
REF
S/R
REF
5
4
GND
INTERNAL
BIAS
2.50V
VREF
GOOD
LOGIC
OUTPUT
R /C
OSC
T
T
OVER TEMP
PROTECT
S
R
Q
Q
ERROR
AMP
2R
2
1
FB
PWM
1V
R
COMP
CS
LATCH
CURRENT
SENSE
3
COMPARATOR
Figure 3. Functional Block Diagram of AP384XG
Ordering Information
AP384XG
-
E1: Lead Free
Blank: Tin Lead
Circuit Type
TR: Tape and Reel
Blank: Tube
Package
M: SOIC-8
P: DIP-8
Part Number
Marking ID
Tempera-
ture Range
Packing
Type
Package
Tin Lead
Lead Free
Tin Lead
3842/3/4/5GM
3842/3/4/5GM
AP3842/3/4/5GP
Lead Free
AP3842/3/4/5GM
AP3842/3/4/5GMTR AP3842/3/4/5GMTR-E1
AP3842/3/4/5GP AP3842/3/4/5GP-E1
AP3842/3/4/5GM-E1
3842/3/4/5GM-E1
3842/3/4/5GM-E1
AP3842/3/4/5GP-E1
Tube
Tape & Reel
Tube
-40 to 85oC
-40 to 85oC
SOIC-8
DIP-8
BCD Semiconductor's Pb-free products, as designated with "E1" suffix in the part number, are RoHS compliant.
BCD Semiconductor Manufacturing Limited
Apr. 2007 Rev. 1. 3
3
Data Sheet
GREEN MODE PWM CONTROLLER
AP384XG
Absolute Maximum Ratings (Note 1, 2)
Parameter
Symbol
Value
Unit
Supply Voltage
VCC
30
V
Gate Output Current
IO
A
± 1
-0.3 to 6.3
20
Analog Inputs (pin2, 3)
V(ANA)
V
Error Amp Output Sink Current
I
SINK(E.A)
mA
Power Dissipation at TA< 25 oC (DIP-8)
P
P
D (Note 3)
D (Note 3)
1000
460
mW
mW
Power Dissipation at TA<25 oC (SOIC-8)
Storage Temperature Range
Ambient Temperature
oC
oC
TSTG
TA
-65 to 150
-40 to 85
+300
oC
V
Lead Temperature (Soldering, 10sec)
ESD (Machine Model)
TLEAD
300
Note 1: Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the
device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indi-
cated under "Recommended Operating Conditions" is not implied. Exposure to "Absolute Maximum Ratings" for extended
periods may affect device reliability.
Note 2: All voltages are with respect to pin GND and all currents are positive into specified terminal.
Note 3: Board thickness 1.6mm, board dimension 90mm x 90mm.
Recommended Operating Conditions
Symbol
Parameter
Min
Max
500
85
Unit
Oscillation Frequency
Ambient Temperature
f
KHz
oC
TA
-40
BCD Semiconductor Manufacturing Limited
Apr. 2007 Rev. 1. 3
4
Data Sheet
GREEN MODE PWM CONTROLLER
AP384XG
Electrical Characteristics
o
(V =15V, R =10kΩ C =3.3nF, T = -40 to 85 C, unless otherwise specified.)
CC
T
T
A
Parameter
Symbol
Conditions
Min
Typ
Max
Unit
REFERENCE SECTION
Reference Output Voltage
Total Output Variation
Line Regulation
TJ=25oC, IREF=1mA
Line, Load, Temp.
VREF
4.95
4.9
5.00
5.05
5.10
15
V
V
ΔVREF
ΔVREF
ISC
12V ≤ VCC ≤25V
4
4
mV
mV
mA
Load Regulation
1mA ≤ IREF ≤20mA
15
TA=25oC
Short Circuit Output Current
Temperature Stability
-100
0.2
-180
0.4
mV/oC
UNDER VOLTAGE LOCK OUT SECTION
Start-up Threshold
AP3842G/AP3844G
AP3843G/AP3845G
AP3842G/AP3844G
AP3843G/AP3845G
15
7.8
8.5
7.0
16
8.4
10
17
9.0
V
V
Minimum Operating Voltage
11.5
8.2
7.6
TOTAL STANDBY CURRENT SECTION
Start-up Current
VCC=14V
50
8
80
μA
mA
mA
V
Operating Current
VFB=0, VCS=0, CL=1nF
Standby Operating Current
Zener Voltage
VFB=2.7V, VCS=0.5V
6
ICC=25mA
30
34
PWM SECTION
Maximum Duty Cycle
AP3842G/AP3843G
AP3844G/AP3845G
94
46
96
48
%
%
50
0
Minimum Duty Cycle
OSCILLATOR SECTION
TJ=25oC
Oscillation Frequency
Oscillator Amplitude
Temperature Stability
Voltage Stability
f
47
52
1.7
2
57
KHz
V
VOSC
Pin RT/CT, peak to peak
%
0.2
9.5
1
%
12V ≤VCC ≤25V
Discharge Current
VRT/CT = 2V (Note 4)
8.5
10.5
mA
Note 4: This parameter is measured with RT=10kΩ to V
it contributes 0.3mA of current to the measured value.
REF,
So the total current flowing into the CT pin will be 0.3mA higher than the measured value approximately.
BCD Semiconductor Manufacturing Limited
Apr. 2007 Rev. 1. 3
5
Data Sheet
GREEN MODE PWM CONTROLLER
AP384XG
Electrical Characteristics (Continued)
Parameter
Symbol
Conditions
Min
Typ
Max
Unit
ERROR AMPLIFIER SECTION
Input Voltage
VI
ISINK
ISOURCE
VOH
VCOMP=2.5V
2.45
6
2.50
10
2.55
V
mA
mA
V
Output Sink Current
Output Source Current
High Output Voltage
Low Output Voltage
Voltage Gain
VCOMP=1.1V
VCOMP=5V
-0.5
5
-0.8
7
RL=15kΩ to GND
RL=15kΩ to pin REF
2V ≤ VO ≤ 4V
VOL
0.7
90
1.1
V
65
60
dB
dB
Power Supply Rejection Ratio
CURRENT SENSE SECTION
PSRR
12V ≤ VCC ≤ 25V
70
Maximum Input Signal
Gain
VI(MAX)
GV
VCOMP=5V (Note 5)
0.9
1
3
1.1
V
V/V
dB
ns
0V ≤ VCS ≤ 4V (Note 5, 6)
12V ≤ VCC ≤ 25V (Note 5, 7)
VCS= 0 to 2V (Note 7)
VOUTPUT=High
2.85
3.15
Power Supply Rejection Ratio
Delay to Output
PSRR
70
150
-3
250
-10
Input Bias Current
IBIAS
TLEB
μA
ns
Leading Edge Blanking Duration
OUTPUT SECTION
250
Low Output Voltage
ISINK = 20mA
0.2
1.4
13.5
13
0.4
2.2
V
V
V
V
ns
ns
VOL
ISINK = 200mA
ISOURCE = 20mA
ISOURCE = 200mA
High Output Voltage
13
12
VOH
TJ=25oC, CL=1nF
TJ=25oC, CL=1nF
Rise Time
tR
tF
150
50
250
150
Fall Time
SKIP CYCLE MODE SECTION
Source Current (@ CS)
OUTPUT=Low, TJ=25oC
180
200
220
μA
V
OVER-TEMPERATURE PROTECT SECTION
oC
oC
Shutdown Temperature
Temperature Hysteresis
TSHUT
THYS
155
25
Note 5: Parameters are tested at trip point of latch with Vpin2 = 0.
Note 6: Here gain is defined as:
ΔVPin 1
A=
, 0 ≤ Vpin3 ≤ 0.8V
ΔVPin 3
Note 7: These parameters, although guaranteed, are not 100% tested in production.
BCD Semiconductor Manufacturing Limited
Apr. 2007 Rev. 1. 3
6
Data Sheet
GREEN MODE PWM CONTROLLER
AP384XG
Electrical Characteristics (Continued)
VREF
RT
AP3842G
4.7k
2N2222
100k
A
VCC
1
2
3
4
8
7
6
5
REF
COMP
1k
VCC
FB
ERROR AMP
ADJUST
0.1μF
1K
1W
5k
ISENSE
ADJUST
CS
OUTPUT
GND
OUTPUT
GND
4.7k
RT/CT
0.1μF
CT
Figure 4. Basic Test Circuit
Figure 4 is the basic test circuit for AP384XG. In testing, the high peak currents associated with capacitive loads
necessitate careful grounding techniques. Timing and bypass capacitors should be connected close to pin 5 in a
single point ground. The transistor and 5k potentiometer are used to sample the oscillator waveform and apply an
adjustable ramp to pin 3.
BCD Semiconductor Manufacturing Limited
Apr. 2007 Rev. 1. 3
7
Data Sheet
GREEN MODE PWM CONTROLLER
AP384XG
Typical Performance Characteristics
100k
50K
30
10
3
1
10k
5K
0.3
100
1k
10k
100k
1M
1
10
22
100
47
2.2
4.7
Frequency (Hz)
Timing Capacitor (nF)
Figure 6. Timing Resistor vs. Frequency
Figure 5. Oscillator Dead Time vs. Timing Capacitor
60
5.015
VCC=15V, IO=1mA
5.010
50
40
30
20
10
0
5.005
5.000
4.995
4.990
4.985
4.980
AP3842G/44G
-40
-20
0
20
40
60
80
100
120
0
2
4
6
8
10
12
14
16
18
Ambient Temperature (oC)
Supply Voltage (V)
Figure 7. Reference Voltage vs. Ambient Temperature
Figure 8. Start-up Current vs. Supply Voltage
BCD Semiconductor Manufacturing Limited
Apr. 2007 Rev. 1. 3
8
Data Sheet
GREEN MODE PWM CONTROLLER
AP384XG
Typical Performance Characteristics (Continued)
90
4.0
3.5
80
70
VCC=15V, TA=25oC
VCC=15V, TA=25oC
3.0
60
2.5
50
2.0
40
1.5
30
20
10
0
1.0
0.5
0.0
-0.5
0
50 100 150 200 250 300 350 400 450 500 550 600
Output Sink Current (mA)
10
100
1k
10k
100k
1M
Frequency (Hz)
Figure 9. Output Saturation Characteristics
Figure 10. Error Amplifier Open-Loop Frequency Response
60
50
40
30
20
AP3842G
-40
-20
0
20
40
60
80
100
120
Ambient Temperature (oC)
Figure 11. Start-up Current vs. Ambient Temperature
BCD Semiconductor Manufacturing Limited
Apr. 2007 Rev. 1. 3
9
Data Sheet
GREEN MODE PWM CONTROLLER
AP384XG
Typical Application
NTC
C14
100μ/400V
R19
10
C2
0.01μ
600V
R3
39k
2W
+
C15
2.2n
R2
1.2M
R20
1M
D3
8TQ100
C11
1μ
L3
10μ
C10
1000μ
R21
3k
Z2
SA12A
JP1
AC
T
D1
90 to 264V
+
FR107
+
C1 47μ
R4 4.7
C9
2200μ
D2
1N4001
JP2
12V/5A
C3
0.1μ
7
2
1
5
8
REF
VCC
R12
100
R5
10k
C4
3.3n
C8
FB
RT/CT
4
6
3
0.22μ
C5
220p
R6
10
C6
220p/600V
R16
8.2k
R15
100
COMP OUTPUT
R14
130k
Q1
IRF830
R7
2k
GND
CS
W1
1k
U3
AZ431
R18
1k
U1
AP384XG
C7
680p
R10
0.51/1W
Z1
1N5819
R9
10k
R13
15k
R17
2k
R11
820
U2 PC817
Figure 12. Typical Application of AP384XG in AC/DC Converter
BCD Semiconductor Manufacturing Limited
Apr. 2007 Rev. 1. 3
10
Data Sheet
GREEN MODE PWM CONTROLLER
AP384XG
Mechanical Dimensions
SOIC-8
Unit: mm(inch)
4.700(0.185)
0.320(0.013)
1.350(0.053)
1.750(0.069)
5.100(0.201)
0.675(0.027)
0.725(0.029)
D
5.800(0.228)
6.200(0.244)
1.270(0.050)
TYP
D
20:1
φ
0.800(0.031)
0.200(0.008)
0.100(0.004)
0.300(0.012)
0°
8°
1.000(0.039)
3.800(0.150)
4.000(0.157)
0.190(0.007)
0.250(0.010)
1°
5°
0.330(0.013)
0.510(0.020)
0.900(0.035)
6)
00
(0.
50
.1
R0
0.450(0.017)
0.800(0.031)
BCD Semiconductor Manufacturing Limited
Apr. 2007 Rev. 1. 3
11
Data Sheet
GREEN MODE PWM CONTROLLER
AP384XG
Mechanical Dimensions (Continued)
DIP-8
Unit: mm(inch)
0.700(0.028)
7.620(0.300)TYP
5°
1.524(0.060) TYP
6°
3.200(0.126)
3.600(0.142)
3.710(0.146)
4.310(0.170)
0.510(0.020)MIN
3.000(0.118)
3.600(0.142)
0.204(0.008)
0.360(0.014)
0.254(0.010)TYP
8.200(0.323)
9.400(0.370)
2.540(0.100)TYP
0.130(0.005)MIN
0.360(0.014)
0.560(0.022)
6.200(0.244)
6.600(0.260)
R0.750(0.030)
Φ3.000(0.118)
Depth
0.100(0.004)
0.200(0.008)
9.000(0.354)
9.400(0.370)
BCD Semiconductor Manufacturing Limited
Apr. 2007 Rev. 1. 3
12
BCD Semiconductor Manufacturing Limited
http://www.bcdsemi.com
- Headquarters
- Wafer Fab
BCD Semiconductor Manufacturing Limited
Shanghai SIM-BCD Semiconductor Manufacturing Co., Ltd.
No. 1600, Zi Xing Road, Shanghai ZiZhu Science-based Industrial Park, 200241, China
800 Yi Shan Road, Shanghai 200233, China
Tel: +86-21-24162266, Fax: +86-21-24162277
Tel: +86-21-6485 1491, Fax: +86-21-5450 0008
REGIONAL SALES OFFICE
Shenzhen Office
Taiwan Office
USA Office
Shanghai SIM-BCD Semiconductor Manufacturing Co., Ltd., Shenzhen Office
BCD Semiconductor (Taiwan) Company Limited
BCD Semiconductor Corp.
Room E, 5F, Noble Center, No.1006, 3rd Fuzhong Road, Futian District, Shenzhen,
4F, 298-1, Rui Guang Road, Nei-Hu District, Taipei,
30920 Huntwood Ave. Hayward,
518026, China
Taiwan
Tel: +886-2-2656 2808
CA 94544, USA
Tel: +86-755-8826 7951
Tel : +1-510-324-2988
Fax: +86-755-8826 7865
Fax: +886-2-2656 2806
Fax: +1-510-324-2788
©2020 ICPDF网 联系我们和版权申明