AP7312-1525W6-7 [DIODES]
Fixed Positive LDO Regulator, 2 Output, 1.5V1, 2.5V2, PDSO6, ROHS COMPLIANT, SOT26-6;型号: | AP7312-1525W6-7 |
厂家: | DIODES INCORPORATED |
描述: | Fixed Positive LDO Regulator, 2 Output, 1.5V1, 2.5V2, PDSO6, ROHS COMPLIANT, SOT26-6 光电二极管 输出元件 调节器 |
文件: | 总18页 (文件大小:285K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
AP7312
DUAL 150mA LOW QUIESCENT CURRENT FAST
TRANSIENT LOW DROPOUT LINEAR REGULATOR
Description
Pin Assignments
The AP7312 is 150mA, dual fixed output voltage, low dropout
linear regulator. The AP7312 include the pass element, error
amplifier, band-gap, current limit and thermal shutdown
circuitry which protect the IC from damage in fault
conditions. The AP7312 has two enable pins (EN1 and EN2)
to independently turn the respective channel on when a logic
high level is applied.
(Top View)
1
2
3
6
5
4
OUT1
IN
OUT2
GND
EN2
The characteristics of low dropout voltage and low quiescent
current make it suitable for low power applications. The
typical quiescent current is approximately 60μA.
EN1
This device is available with fixed output options of
1.2V/1.8V, 1.2V/3.3V, 1.5V/2.5V, 1.5V/3.3V, 1.8V/2.8V,
1.8V/3.0V, 1.8V/3.3V and 3.3V/3.3V.
SOT26
For other output options please contact our local sales
representative directly or through our distributor located in
your area.
(Top View)
The AP7312 is available in SOT26 and DFN2018-6
packages.
1
2
3
6
5
4
IN
OUT1
OUT2
GND
EN1
EN2
Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
150mA Low Dropout Regulator with EN
Very low IQ: 60µA
DFN2018-6
Wide input voltage range: 2V to 6V
Fixed output options: 1.2V to 3.3V
High PSRR: 65dB at 1kHz
Applications
Fast start-up time: 60µs
Stable with low ESR, 1µF ceramic output capacitor
Excellent Load/Line Transient Response
Low dropout: 150mV at 150mA
Current limit protection
•
•
•
•
•
Cellular Phones
Smart Phones, PDAs
MP3/MP4
Short circuit protection
Bluetooth head set
Low power application
Thermal shutdown protection
Ambient temperature range: -40ºC to 85°C
SOT26 and DFN2018-6: Available in “Green” Molding
Compound (No Br, Sb)
•
Lead Free Finish/RoHS Compliant (Note 1)
Note:
1. EU Directive 2002/95/EC (RoHS). All applicable RoHS exemptions applied. Please visit our website at
http://www.diodes.com/products/lead_free.html.
1 of 18
www.diodes.com
January 2011
© Diodes Incorporated
AP7312
Document number: DS35133 Rev. 2 - 2
AP7312
DUAL 150mA LOW QUIESCENT CURRENT FAST
TRANSIENT LOW DROPOUT LINEAR REGULATOR
Typical Application Circuit
VIN
VOUT1
VIN VOUT1
1uF
1uF
VOUT2
EN1 VOUT2
ON
ON
OFF
1uF
EN2
GND
OFF
Pin Descriptions
Pin Number
Pin Name
Description
SOT26
DFN2018-6
OUT2
GND
EN2
EN1
IN
1
2
3
4
5
6
5
4
3
2
1
6
Voltage output 2. Bypass to ground through 1µF ceramic capacitor
Ground
Enable input 2, active high
Enable input 1, active high
Voltage input. Bypass to ground through at least 1µF capacitor
Voltage output 1. Bypass to ground through 1µF ceramic capacitor
OUT1
2 of 18
www.diodes.com
January 2011
© Diodes Incorporated
AP7312
Document number: DS35133 Rev. 2 - 2
AP7312
DUAL 150mA LOW QUIESCENT CURRENT FAST
TRANSIENT LOW DROPOUT LINEAR REGULATOR
Functional Block Diagram
OUT 1
IN
Current Limit
and
Short Circuit
Gate
Driver
EN 1
Bandgap
Thermal
Shutdown
GND
Current Limit
Gate
EN 2
and
Driver
Short Circuit
OUT 2
3 of 18
www.diodes.com
January 2011
© Diodes Incorporated
AP7312
Document number: DS35133 Rev. 2 - 2
AP7312
DUAL 150mA LOW QUIESCENT CURRENT FAST
TRANSIENT LOW DROPOUT LINEAR REGULATOR
Absolute Maximum Ratings
Symbol
Parameter
Ratings
8
Unit
kV
V
ESD HBM
ESD MM
VIN
Human Body Model ESD Protection
Machine Model ESD Protection
Input Voltage
400
6.5
V
OUT, EN Voltage
VIN + 0.3
Internal Limited
-40 ~ 125
-65 ~150
950
V
Continuous Load Current
Operating Junction Temperature Range
Storage Temperature Range
TOP
TST
°C
°C
SOT26
mW
mW
°C
PD
TJ
Power Dissipation (Note 3)
DFN2018-6
2200
Maximum Junction Temperature
150
Recommended Operating Conditions
Symbol
Parameter
Min
Max
Unit
V
Input voltage
2
0
6
VIN
IOUT
TA
Output Current (Note 3)
150
85
mA
°C
Operating Ambient Temperature
-40
Notes:
2. Ratings apply to ambient temperature at 25°C.
3. The device maintains a stable, regulated output voltage without a load current.
4 of 18
www.diodes.com
January 2011
© Diodes Incorporated
AP7312
Document number: DS35133 Rev. 2 - 2
AP7312
DUAL 150mA LOW QUIESCENT CURRENT FAST
TRANSIENT LOW DROPOUT LINEAR REGULATOR
Electrical Characteristics
(TA = 25oC, VIN = VOUT +1V, CIN = 1uF, COUT = 1uF, VEN = VIN, unless otherwise stated)
Symbol
Parameter
Test Conditions
Min Typ. Max Unit
ADJ Reference Voltage
(Adjustable version)
IOUT= 0mA
0.8
0.1
V
μA
%
VREF
IADJ
ADJ Leakage (Adjustable version)
1
2
TA = -40oC to 85oC,
OUT = 10% of IOUT-Max
Output Voltage Accuracy
Line Regulation
-2
VOUT
I
VIN = (VOUT +1V) to VIN-Max
VEN = VIN, IOUT = 1mA
VIN = (VOUT +1V) to VIN-Max
,
,
0.01 0.20 %/V
ΔVOUT /ΔVIN/V
ΔVOUT /VOUT
Load Regulation
-0.6
0.6
%
I
OUT = 1mA to 150mA
V
OUT < 2.5V, IOUT = 150mA
200
150
60
300
200
80
Dropout Voltage (Note 4)
mV
VDropout
VOUT ≥ 2.5V, IOUT = 150mA
VEN = VIN, IOUT = 0mA
Input Quiescent Current (2 channels)
Input Shutdown Current
μA
μA
μA
IQ
VEN = 0V, IOUT = 0mA
0.1
0.1
1
1
ISHDN
ILEAK
Input Leakage Current
VEN = 0V, OUT grounded
VEN = 0V to 2.0V in 1μs,
IOUT = 150mA
VIN = [VOUT +1V]VDC + 0.5VppAC
f = 1kHz, IOUT = 50mA
Start-up Time
150
65
μs
dB
tST
,
PSRR (Note 5)
Short-circuit Current
Current limit
60
PSRR
ISHORT
ILIMIT
VIN = VIN-Min to VIN-Max
,
60
mA
mA
VOUT = 1/4 target VOUT
VIN = VIN-Min to VIN-Max
,
200
300
VOUT/ROUT = 0.6A
EN Input Logic Low Voltage
EN Input Logic High Voltage
EN Input Current
VIN = VIN-Min to VIN-Max
VIN = VIN-Min to VIN-Max
VIN = 0V or VIN-Max
0.4
1
V
V
VIL
VIH
1.4
-1
μA
°C
°C
IEN
Thermal shutdown threshold
Thermal shutdown hysteresis
165
TSHDN
THYS
30
140
60
SOT26 (Note 6)
DFN2018-6 (Note 7)
Thermal Resistance Junction-to-Ambient
oC/W
θJA
Notes:
4. Dropout voltage is the voltage difference between the input and the output at which the output voltage drops 2% below its nominal value.
5. This specification is guaranteed by design.
6. Test condition for SOT26: Device mounted on FR-4 substrate PC board, with minimum recommended pad layout
7. Test condition for DFN2018-6: Device mounted on FR-4 2-layer board,2oz copper, with minimum recommended pad on top layer and 3 vias to
bottom layer.
5 of 18
www.diodes.com
January 2011
© Diodes Incorporated
AP7312
Document number: DS35133 Rev. 2 - 2
AP7312
DUAL 150mA LOW QUIESCENT CURRENT FAST
TRANSIENT LOW DROPOUT LINEAR REGULATOR
Typical Performance Characteristics
Start-Up Time
Start-Up Time
VIN=5V, No load
VIN=5V, Both ILOAD=150mA
CIN=COUT1=COUT2=1μF
CIN=COUT1=COUT2=1μF
VEN=0V to 2V (2V/div)
VEN=0V to 2V (2V/div)
VOUT2=2.8V (1V/div)
VOUT1=1.8V (1V/div)
V
OUT2=2.8V (1V/div)
VOUT1=1.8V (1V/div)
Time (40μs/div)
Time (40μs/div)
Line Transient Response
VIN=3.8V to 4.8V (1V/div)
Line Transient Response
VIN=3.8V to 4.8V (1V/div)
COUT1=COUT2=1μF, Tr=Tf=2μs, Both ILOAD=15mA
COUT1=COUT2=1μF, Tr=Tf=2μs, Both ILOAD=100mA
VOUT1=1.8V (10mV/div)
VOUT1=1.8V (10mV/div)
VOUT2=2.8V (10mV/div)
VOUT2=2.8V (10mV/div)
Time (100μs/div)
Time (100μs/div)
6 of 18
www.diodes.com
January 2011
© Diodes Incorporated
AP7312
Document number: DS35133 Rev. 2 - 2
AP7312
DUAL 150mA LOW QUIESCENT CURRENT FAST
TRANSIENT LOW DROPOUT LINEAR REGULATOR
Typical Performance Characteristics (Continued)
Load Transient Response
Load Transient Response
ILOAD=10mA to 50mA (50mA/div)
ILOAD=10mA to 100mA (100mA/div)
VOUT1=1.8V (20mV/div)
VOUT1=1.8V (20mV/div)
VOUT2=2.8V (20mV/div)
VOUT2=2.8V (20mV/div)
VIN=VEN=3.8V
CIN=COUT1=COUT2=1μF
VIN=VEN=3.8V
CIN=COUT1=COUT2=1μF
Time (100μs/div)
Time (100μs/div)
EN1 Pin Response
Both ILOAD=50mA
EN2 Pin Response
V
EN1=2V (2V/div)
Both ILOAD=50mA
VEN1=2V to 0V (2V/div)
VEN2=2V (2V/div)
V
EN2=2V to 0V (2V/div)
OUT2=2.8V (1V/div)
VOUT2=2.8V (1V/div)
V
VOUT1=1.8V (1V/div)
VOUT1=1.8V (1V/div)
Time (400μs/div)
Time (400μs/div)
7 of 18
www.diodes.com
January 2011
© Diodes Incorporated
AP7312
Document number: DS35133 Rev. 2 - 2
AP7312
DUAL 150mA LOW QUIESCENT CURRENT FAST
TRANSIENT LOW DROPOUT LINEAR REGULATOR
Typical Performance Characteristics (Continued)
EN Pin Shutdown Response
VIN=5V, Both ILOAD=50mA
PSRR vs Frequency
100
80
60
40
20
0
1.8V
2.8V
VEN=0V to 5V (5V/div)
TA=25°C
VOUT2=2.8V (1V/div)
VIN=3.8V+0.5VppAC
COUT1=COUT2=1μF
Both ILOAD=50mA
VOUT1 =1.8V (1V/div)
10
1k
1M
100
10k 100k
Frequency(Hz)
Time (100μs/div)
Input Quiescent current vs Temperature
Input Quiescent current vs Input Voltage
80
60
40
20
0
80
60
40
20
0
TA=25°C
VIN=VEN=3.8V
VOUT1=1.8V
VOUT2=2.8V
IOUT=0mA
VOUT1=1.8V
VOUT2=2.8V
IOUT=0mA
-50
-25
0
25
50
75
100 125
3.5
4
4.5
5
5.5
6
Temperature(
)
℃
Input Voltage(V)
8 of 18
www.diodes.com
January 2011
© Diodes Incorporated
AP7312
Document number: DS35133 Rev. 2 - 2
AP7312
DUAL 150mA LOW QUIESCENT CURRENT FAST
TRANSIENT LOW DROPOUT LINEAR REGULATOR
Typical Performance Characteristics (Continued)
Line Regulation
Line Regulation
0.2
0.1
0.04
0.02
0
-45°C
25°C
-45°C
25°C
0.0
90°C
90°C
-0.02
-0.04
-0.1
-0.2
VOUT=1.8V
IOUT=1mA
VOUT=2.8V
IOUT=1mA
3.5
4
4.5
5
5.5
6
2.5
3
3.5
4
4.5
5
5.5
6
Input Voltage(V)
Input Voltage(V)
Load Regulation
Load Regulation
0.00
-0.05
-0.10
-0.15
0.00
-0.05
-0.10
-0.15
-45°C
-45°C
25°C
25°C
90°C
90°C
VIN=VEN=3.8V
VOUT=2.8V
VIN=VEN=2.8V
VOUT=1.8V
0
25
50
75
100
125
150
0
25
50
75
100
125
150
Output Current(mA)
Output Current(mA)
9 of 18
www.diodes.com
January 2011
© Diodes Incorporated
AP7312
Document number: DS35133 Rev. 2 - 2
AP7312
DUAL 150mA LOW QUIESCENT CURRENT FAST
TRANSIENT LOW DROPOUT LINEAR REGULATOR
Typical Performance Characteristics (Continued)
Dropout Voltage vs Output Current
Dropout Voltage vs Output Current
250
200
150
100
50
200
150
100
50
VOUT=3.3V
VOUT=1.8V
90°C
25°C
90°C
25°C
-45°C
-45°C
0
0
0
25
50
75
100
125
150
0
25
50
75
100
125
150
Output Current(mA)
Output Current(mA)
Current limit vs Input Voltage
Current limit vs Temperature
500
400
300
200
100
0
500
400
300
200
100
0
TA=25°C
VIN=2.8V
-50 -25
0
25
50
75
100 125
2
3
4
5
6
Temperature(
)
℃
Input Voltage(V)
10 of 18
www.diodes.com
January 2011
© Diodes Incorporated
AP7312
Document number: DS35133 Rev. 2 - 2
AP7312
DUAL 150mA LOW QUIESCENT CURRENT FAST
TRANSIENT LOW DROPOUT LINEAR REGULATOR
Typical Performance Characteristics (Continued)
Short-circuit Current vs Temperature
Short Circuit Current vs Input Voltage
100
80
60
40
20
0
100
80
60
40
20
0
VIN=3.8V
25°C
-45°C
90°C
-50
-25
0
25
50
75
100 125
2.5
3
3.5
4
4.5
5
5.5
6
Temperature(
)
Input Voltage(V)
℃
11 of 18
www.diodes.com
January 2011
© Diodes Incorporated
AP7312
Document number: DS35133 Rev. 2 - 2
AP7312
DUAL 150mA LOW QUIESCENT CURRENT FAST
TRANSIENT LOW DROPOUT LINEAR REGULATOR
Application Note
Input Capacitor
A 1μF ceramic capacitor is recommended between IN and GND pins to decouple input power supply glitch and noise. The
amount of the capacitance may be increased without limit. This input capacitor must be located as close as possible to the
device to assure input stability and reduce noise. For PCB layout, a wide copper trace is required for both IN and GND pins.
A lower ESR capacitor type allows the use of less capacitance, while higher ESR type requires more capacitance.
Output Capacitor
The output capacitor is required to stabilize and improve the transient response of the LDO. The AP7312 is stable with very
small ceramic output capacitors. Using a ceramic capacitor value that is at least 1μF with ESR≧10mΩ on the output ensures
stability. Higher capacitance values help to improve line and load transient response. The output capacitance may be
increased to keep low undershoot and overshoot. Output capacitor must be placed as close as possible to OUT and GND
pins.
Region of Stable COUT ESR vs. Load Current
100
Unstable Range
10
1
Stable Range
0.1
0.01
CIN=COUT1= COUT2=1μF
Unstable Range
0.001
0
20
50
100
150
Load Current (mA)
No Load Stability
Other than external resistor divider, no minimum load is required to keep the device stable. The device will remain stable and
regulated in no load condition.
ON/OFF Input Operation
The AP7312 is turned on by setting the EN pin high, and is turned off by pulling it low. If this feature is not used, the EN pin
should be tied to IN pin to keep the regulator output on at all time. To ensure proper operation, the signal source used to drive
the EN pin must be able to swing above and below the specified turn-on/off voltage thresholds listed in the Electrical
Characteristics section under VIL and VIH.
12 of 18
www.diodes.com
January 2011
© Diodes Incorporated
AP7312
Document number: DS35133 Rev. 2 - 2
AP7312
DUAL 150mA LOW QUIESCENT CURRENT FAST
TRANSIENT LOW DROPOUT LINEAR REGULATOR
Application Note (Continued)
Current Limit Protection
When output current at OUT pin is higher than current limit threshold, the current limit protection will be triggered and clamp
the output current to approximately 300mA to prevent over-current and to protect the regulator from damage due to
overheating.
Short Circuit Protection
When OUT pin is short-circuit to GND, short circuit protection will be triggered and clamp the output current to approximately
60mA. This feature protects the regulator from over-current and damage due to overheating.
Thermal Shutdown Protection
Thermal protection disables the output when the junction temperature rises to approximately +165°C, allowing the device to
cool down. When the junction temperature reduces to approximately +135°C the output circuitry is enabled again. Depending
on power dissipation, thermal resistance, and ambient temperature, the thermal protection circuit may cycle on and off. This
cycling limits the heat dissipation of the regulator, protecting it from damage due to overheating.
Ultra Fast Start-up
After enabled, the AP7312 is able to provide full power in as little as tens of microseconds, typically 150µs, without sacrificing
low ground current. This feature will help load circuitry move in and out of standby mode in real time, eventually extend
battery life for mobile phones and other portable devices.
Fast Transient Response
Fast transient response LDO can extend battery life. TDMA-based cell phone protocols such as Global System for Mobile
Communications (GSM) have a transmit/receive duty factor of only 12.5 percent, enabling power savings by putting much of
the baseband circuitry into standby mode in between transmit cycles. In baseband circuits, the load often transitions virtually
instantaneously from 100µA to 100mA. To meet this load requirement, the LDO must react very quickly without a large
voltage drop or overshoot — a requirement that cannot be met with conventional, general-purpose LDO.
The AP7312’s fast transient response from 0 to 150mA provides stable voltage supply for fast DSP and GSM chipset with
fast changing load.
Low Quiescent Current
The AP7312, consuming only around 60µA for all input range, provides great power saving in portable and low power
applications.
Power Dissipation
The device power dissipation and proper sizing of the thermal plane that is connected to the thermal pad is critical to avoid
thermal shutdown and ensure reliable operation. Power dissipation of the device depends on input voltage and load
conditions and can be calculated by:
PD = (VIN - VOUT) X IOUT
The maximum power dissipation, handled by the device, depends on the maximum junction to ambient thermal resistance,
maximum ambient temperature, and maximum device junction temperature, which can be calculated by the equation in the
following:
(+150°C - T )
A
PD (max@TA) =
R
θJA
13 of 18
www.diodes.com
January 2011
© Diodes Incorporated
AP7312
Document number: DS35133 Rev. 2 - 2
AP7312
DUAL 150mA LOW QUIESCENT CURRENT FAST
TRANSIENT LOW DROPOUT LINEAR REGULATOR
Ordering Information
AP7312- XXYY XX - 7
Output Voltage : VOUT1/VOUT2
Packing
Package
7 : Tape & Reel
FM : DFN2018-6
W6 : SOT26
1218 : 1.2V / 1.8V
1233 : 1.2V / 3.3V
1525 : 1.5V / 2.5V
1533 : 1.5V / 3.3V
1828 : 1.8V / 2.8V
1830 : 1.8V / 3.0V
1833 : 1.8V / 3.3V
3333 : 3.3V / 3.3V
7” Tape and Reel
Packaging
(Note 8)
Device
Package Code
Quantity
Part Number Suffix
AP7312-XXYY W6-7
AP7312-XXYY FM-7
W6
FM
SOT26
3000/Tape & Reel
3000/Tape & Reel
-7
-7
DFN2018-6
Note:
8. Pad layout as shown on Diodes Inc. suggested pad layout document AP02001, which can be found on our website at
http://www.diodes.com/datasheets/ap02001.pdf.
14 of 18
www.diodes.com
January 2011
© Diodes Incorporated
AP7312
Document number: DS35133 Rev. 2 - 2
AP7312
DUAL 150mA LOW QUIESCENT CURRENT FAST
TRANSIENT LOW DROPOUT LINEAR REGULATOR
Marking Information
(1) SOT26
( Top View )
6
5
4
XXX : Identification code
Y : Year 0~9
W : Week : A~Z : 1~26 week;
a~z : 27~52 week; z represents
52 and 53 week
XXX
Y W X
X : A~Z : Internal Code
1
2
3
(2) DFN2018-6
( Top View )
XXX : Identification code
Y : Year : 0~9
W : Week : A~Z : 1~26 week;
a~z : 27~52 week; z represents
52 and 53 week
XXX
Y W X
X : A~Z : Internal Code
Device
Package
SOT26
SOT26
SOT26
SOT26
SOT26
SOT26
SOT26
SOT26
Package
Identification Code
AP7312-1218
AP7312-1233
AP7312-1525
AP7312-1533
AP7312-1828
AP7312-1830
AP7312-1833
AP7312-3333
DFN2018-6
DFN2018-6
DFN2018-6
DFN2018-6
DFN2018-6
DFN2018-6
DFN2018-6
DFN2018-6
CAS
CAZ
CA6
CBC
CBK
CBN
CBR
CEA
15 of 18
www.diodes.com
January 2011
© Diodes Incorporated
AP7312
Document number: DS35133 Rev. 2 - 2
AP7312
DUAL 150mA LOW QUIESCENT CURRENT FAST
TRANSIENT LOW DROPOUT LINEAR REGULATOR
Package Outline Dimensions (All Dimensions in mm)
(1) SOT26
(2) DFN2018-6
0.10 C
0.08 C
6X-
Seating Plane
Side View
C
L
C
1.75/1.875
A
B
C
L
C
L
Pin #1 ID
Pin #1
1.3/1.5
C
L
4x-0.50
6x-0.25
1.600
Land Pattern Recommendation
(Unit:mm)
Top View
2X-
0.25 B
0.50Typ
0.15/0.25
0.10
C A
B
Bottom View
16 of 18
www.diodes.com
January 2011
© Diodes Incorporated
AP7312
Document number: DS35133 Rev. 2 - 2
AP7312
DUAL 150mA LOW QUIESCENT CURRENT FAST
TRANSIENT LOW DROPOUT LINEAR REGULATOR
Taping Orientation (Note 9)
For DFN2018-6
Note: 9. The taping orientation of the other package type can be found on our website at http://www.diodes.com/datasheets/ap02007.pdf
17 of 18
www.diodes.com
January 2011
© Diodes Incorporated
AP7312
Document number: DS35133 Rev. 2 - 2
AP7312
DUAL 150mA LOW QUIESCENT CURRENT FAST
TRANSIENT LOW DROPOUT LINEAR REGULATOR
IMPORTANT NOTICE
DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS
DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION).
Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other
changes without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability
arising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any
license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described
herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies
whose products are represented on Diodes Incorporated website, harmless against all damages.
Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized
sales channel.
Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall
indemnify and hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application.
Products described herein may be covered by one or more United States, international or foreign patents pending. Product names
and markings noted herein may also be covered by one or more United States, international or foreign trademarks.
LIFE SUPPORT
Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without
the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein:
A. Life support devices or systems are devices or systems which:
1. are intended to implant into the body, or
2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided
in the labeling can be reasonably expected to result in significant injury to the user.
B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected
to cause the failure of the life support device or to affect its safety or effectiveness.
Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or
systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements
concerning their products and any use of Diodes Incorporated products in such safety-critical, life support devices or systems,
notwithstanding any devices- or systems-related information or support that may be provided by Diodes Incorporated. Further,
Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes
Incorporated products in such safety-critical, life support devices or systems.
Copyright © 2011, Diodes Incorporated
www.diodes.com
18 of 18
www.diodes.com
January 2011
© Diodes Incorporated
AP7312
Document number: DS35133 Rev. 2 - 2
相关型号:
AP7312-1533FM-7
DUAL 150mA LOW QUIESCENT CURRENT FASTTRANSIENT LOW DROPOUT LINEAR REGULATOR
DIALIGHT
AP7312-1533FM-7
Fixed Positive LDO Regulator, 2 Output, 1.5V1, 3.3V2, PDSO6, 2 X 1.80 MM, ROHS COMPLIANT, DFN-6
DIODES
AP7312-1533W6-7
DUAL 150mA LOW QUIESCENT CURRENT FASTTRANSIENT LOW DROPOUT LINEAR REGULATOR
DIALIGHT
AP7312-1533W6-7
Fixed Positive LDO Regulator, 2 Output, 1.5V1, 3.3V2, PDSO6, ROHS COMPLIANT, SOT26-6
DIODES
AP7312-1828FM-7
DUAL 150mA LOW QUIESCENT CURRENT FASTTRANSIENT LOW DROPOUT LINEAR REGULATOR
DIALIGHT
AP7312-1828FM-7
Fixed Positive LDO Regulator, 2 Output, 1.8V1, 2.8V2, PDSO6, 2 X 1.80 MM, ROHS COMPLIANT, DFN-6
DIODES
AP7312-1828W6-7
DUAL 150mA LOW QUIESCENT CURRENT FASTTRANSIENT LOW DROPOUT LINEAR REGULATOR
DIALIGHT
AP7312-1830FM-7
DUAL 150mA LOW QUIESCENT CURRENT FASTTRANSIENT LOW DROPOUT LINEAR REGULATOR
DIALIGHT
AP7312-1830FM-7
Fixed Positive LDO Regulator, 2 Output, 1.8V1, 3V2, PDSO6, 2 X 1.80 MM, ROHS COMPLIANT, DFN-6
DIODES
AP7312-1830W6-7
DUAL 150mA LOW QUIESCENT CURRENT FASTTRANSIENT LOW DROPOUT LINEAR REGULATOR
DIALIGHT
AP7312-1833FM-7
DUAL 150mA LOW QUIESCENT CURRENT FASTTRANSIENT LOW DROPOUT LINEAR REGULATOR
DIALIGHT
AP7312-1833W6-7
DUAL 150mA LOW QUIESCENT CURRENT FASTTRANSIENT LOW DROPOUT LINEAR REGULATOR
DIALIGHT
©2020 ICPDF网 联系我们和版权申明