AP7363-18SP-13 [DIODES]
Fixed Positive LDO Regulator, 1.8V, 0.28V Dropout, BIPolar, PDSO8, GREEN, SOP-8;型号: | AP7363-18SP-13 |
厂家: | DIODES INCORPORATED |
描述: | Fixed Positive LDO Regulator, 1.8V, 0.28V Dropout, BIPolar, PDSO8, GREEN, SOP-8 光电二极管 输出元件 调节器 |
文件: | 总14页 (文件大小:375K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
AP7363
1.5A LOW QUIESCENT CURRENT, FAST TRANSIENT
ULTRA-LOW DROPOUT LINEAR REGULATOR
Description
Pin Assignments
The AP7363 is a 1.5A adjustable output voltage linear regulator with
ultra-low dropout. The device includes pass element, error amplifier,
band-gap, current limit and thermal shutdown circuitry.
(Top View)
ADJ/
NC
OUT OUTOUT
8
7
6
5
The characteristics of low dropout voltage and fast transient response
to step changes in load make it suitable for low voltage
microprocessor applications. The typical quiescent current is
approximately 0.5mA and changes little with load current. The built-in
current-limit and thermal-shutdown functions prevent IC from damage
in fault conditions.
1
2
3
4
This device is available in U-DFN2030-8, SO-8EP, SOT223 and
TO252 packages.
GND IN IN IN
U-DFN2030-8
(Top View)
Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1.5A ultra-low dropout linear regulator
Ultra-low dropout: 190mV at 1.5A
1
2
3
4
8
7
6
5
GND
IN
ADJ/NC
OUT
Stable with 10µF input/output capacitor, any types
Wide input voltage range: 2.2V to 5.5V
Adjustable output voltage: 0.6V to 5.0V
Fixed output options: 1V, 1.2V, 1.5V, 1.8V, 2.5V, 3.3V
Low ground pin current
OUT
IN
OUT
IN
25nA quiescent current in shutdown mode
SO-8EP
V
ADJ accuracy of ±1.5% @ +25°C
VADJ accuracy of ±3% over line, load and temperature
Excellent Load/Line Transient Response
(Top View)
Current limit and thermal shutdown protection
Ambient temperature range: -40°C to +85°C
OUT
3
2
U-DFN2030-8, SO-8EP, SOT223 and TO252: Available in
“Green” Molding Compound (No Br, Sb)
GND (TAB)
IN
•
•
Totally Lead-Free & Fully RoHS Compliant (Notes 1 & 2)
Halogen and Antimony Free. “Green” Device (Note 3)
1
SOT223
(Fixed Output)
Applications
(Top View)
•
ASIC power supplies in printers, graphics cards, DVD players,
STBs, routers, etc
3
2
•
•
•
FPGA and DSP core or I/O power supplies
SMPS regulator
GND
Conversion from 3.3V or 5V rail
1
TO252
Notes:
1. No purposely added lead. Fully EU Directive 2002/95/EC (RoHS) & 2011/65/EU (RoHS 2) compliant.
2. See http://www.diodes.com for more information about Diodes Incorporated’s definitions of Halogen- and Antimony-free, "Green" and Lead-free.
3. Halogen- and Antimony-free "Green” products are defined as those which contain <900ppm bromine, <900ppm chlorine (<1500ppm total Br + Cl)
and <1000ppm antimony compounds.
1 of 14
www.diodes.com
December 2012
© Diodes Incorporated
AP7363
Document number: DS35059 Rev. 8 - 2
AP7363
Typical Applications Circuit
VIN
VOUT
VIN
VOUT
IN
OUT
IN
OUT
AP7363
AP7363
R1
R2
10µF
10µF
10µF
10µF
ADJ
GND
GND
Fixed Output
Adjustable Output
⎛
⎞
⎟
⎟
⎠
R1
R2
⎜
VOUT = VREF 1+
whereR2 ≤10kΩ
⎜
⎝
Pin Descriptions
Pin Number
Pin
Name
Function
SOT223
TO252
U-DFN2030-8
SO-8EP
GND
IN
2
1
3
1
Ground.
2, 3, 4
5, 6, 7
Voltage input pin.
Voltage output pin.
OUT
Output feedback pin for adjustable version only – a resistor divider from this pin to the OUT
pin and ground sets the output voltage.
ADJ
NC
NA
NA
8
8
No connection for fixed output version.
The exposed pad (EP) is used to remove heat from the package and it is recommended that
it is connected to a copper area. The die is electrically connected to the exposed pad. It is
recommended to connect it externally to GND, but should not be the only ground connection.
EP/TAB
—
—
Functional Block Diagram
IN
OUT
IN
OUT
Current Limit
and Thermal
Shutdown
Gate
Driver
Current Limit
and Thermal
Shutdown
Gate
Driver
R
EN
EN
ADJ
0.605V
0.605V
R
GND
GND
Fixed Version
Adjustable Version
2 of 14
www.diodes.com
December 2012
© Diodes Incorporated
AP7363
Document number: DS35059 Rev. 8 - 2
AP7363
Absolute Maximum Ratings (cont.) (@TA = +25°C, unless otherwise specified.)
Symbol
ESD HBM
ESD MM
VIN
Parameter
Human Body Model ESD Protection
Machine Model ESD Protection
Input Voltage
Ratings
2000
Unit
V
200
V
-0.3 to +6.0
V
OUT Voltage
V
VOUT
-0.3 to VIN +0.3
Internal Limited
-65 to +150
150
Continuous Load Current
Storage Temperature Range
Maximum Junction Temperature
IOUT
TST
TJ
°C
°C
Recommended Operating Conditions (@TA = +25°C, unless otherwise specified.)
Symbol
VIN
Parameter
Min
2.2
0
Max
5.5
Unit
V
Input voltage
Output Current
1.5
A
IOUT
TA
Operating Ambient Temperature
-40
-40
+85
+125
°C
°C
Operating Junction Temperature (Note 5)
TJ
Notes:
4. Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only and
functional operation of the device at these or any other conditions beyond those indicated are not implied. Exposure to absolute-maximum rated
conditions for extended periods may affect device reliability.
5. Operating junction temperature must be evaluated and derated as needed, based on ambient temperature (TA), power dissipation (PD), maximum
allowable operating junction temperature (TJ-MAX), and package thermal resistance (θJA).
3 of 14
www.diodes.com
December 2012
© Diodes Incorporated
AP7363
Document number: DS35059 Rev. 8 - 2
AP7363
Electrical Characteristics (@TA = +25°C, VIN = 3.3V, IOUT = 10mA, CIN = 10µF, COUT = 10µF, unless otherwise specified.)
Minimum and maximum limits are guaranteed through test, design, or statistical correlation. Typical values represent the most likely parametric
norm at TA = +25°C, and are provided for reference purposes only.
Symbol
Parameter
Test Conditions
Min
Typ
Max
0.626
0.635
Unit
0.584
0.575
0.605
TA = +25°C
Over temp
TA = +25°C
Over temp
TA = +25°C
Over temp
TA = +25°C
Over temp
TA = +25°C
Over temp
TA = +25°C
Over temp
V
IN = VIN-MIN to VIN-MAX,
ADJ Pin Voltage
V
VADJ
IOUT = 10mA to 1.5A
50
ADJ Pin Bias Current
nA
mV
IADJ
VIN = VIN-MIN to VIN-MAX
750
240
280
—
190
Dropout Voltage (Note 6)
Line Regulation (Note 7)
Load Regulation (Note 7)
VDROPOUT
IOUT = 1.5A, VOUT = 2.5V
—
—
0.04
0.05
0.18
0.33
1.0
%/V
%/A
ΔVOUT /ΔVIN
ΔVOUT /ΔIOUT
VIN = VIN-MIN to VIN-MAX
IOUT = 10mA to 1.5A
—
1.2
1.3
Ground Pin Current in Normal
Operation Mode
mA
A
IGND
IOUT-PK
ISC
IOUT = 10mA to 1.5A
VOUT ≥ VOUT - NOM -5%
OUT grounded
Peak Output Current
Short Circuit Current
3.6
3.7
TA = +25°C
Over temp
A
2
Turn-Off Delay
Turn-On Delay
25
25
65
61
1.0
μs
μs
td(off)
td(on)
From VEN < VIL to VOUT = OFF, IOUT = 1.5A
From VEN > VIH to VOUT = ON, IOUT = 1.5A
VIN = 3.0V, IOUT = 1.5A, f = 120Hz
PSRR
Ripple Rejection
dB
VIN = 3.0V, IOUT = 1.5A, f = 1kHz
Output Noise Density
Output Noise Voltage
ρn(l/f)
F = 120Hz, COUT = 10μF ceramic
BW = 100Hz – 100kHz,
μV/√Hz
μV(rms)
100
en
COUT = 10μF ceramic
Thermal Shutdown Threshold
Thermal Shutdown Hysteresis
170
10
TSHDN
THYS
TJ rising
°C
TJ falling from TSHDN
U-DFN2030-8 (Note 8)
SO-8EP (Note 8)
SOT223 (Note 8)
TO252 (Note 8)
174.0
52.8
105.7
87.8
28.2
10.0
18.5
17.3
Thermal Resistance Junction-to-
Ambient
oC/W
θJA
U-DFN2030-8 (Note 8)
SO-8EP (Note 8)
SOT223 (Note 8)
TO252 (Note8)
Thermal Resistance Junction-to-Case
oC/W
θJC
Notes:
6. Dropout voltage is the minimum voltage difference between the input and the output at which the output voltage drops 2% below its nominal value.
For any output voltage less than 2.5V, the minimum VIN operating voltage is the limiting factor.
7. The line and load regulation specification contains only the typical number. However, the limits for line and load regulation are included in the adjust
voltage tolerance specification.
8. Device mounted on 2” x 2” FR-4 substrate PCB, 2oz copper with minimum recommended pad layout.
4 of 14
www.diodes.com
December 2012
© Diodes Incorporated
AP7363
Document number: DS35059 Rev. 8 - 2
AP7363
Typical Performance Characteristics (@TJ = +25°C, VIN = 2.7V, CIN = 10µF, COUT = 10µF, IOUT = 10mA, VOUT = 1.8V.)
10k
10k
C
= 10µF CER
C
= 10µF
OUT
OUT
1k
1k
100
10
100
10
100
1000
10k
100k
100
1000
10k
100k
FREQUENCY (Hz)
Noise Density
FREQUENCY (Hz)
Noise Density
3
2.5
2
2
1.5
1
1
25°C
125°C
-40°C
0.5
0
0
0.3
0.2
0
0.5
1
1.5
0
1
2
3
VIN (V)
Turn-On Characteristics
ILOAD (A)
IGND vs. Load Current
0.615
0.610
125°C
25°C
0.605
0.600
0.595
0.590
-40°C
0.1
0
0
0.5
LOAD CURRENT (A)
Dropout Voltage vs. Load Current
1
1.5
-50 -25
0
25
50
75 100 125
TEMPERATURE (°C)
VADJ vs. Temperature
5 of 14
www.diodes.com
December 2012
© Diodes Incorporated
AP7363
Document number: DS35059 Rev. 8 - 2
AP7363
Typical Performance Characteristics (cont.)
(@TJ = +25°C, VIN = 2.7V, CIN = 10µF, COUT = 10µF, IOUT = 10mA, VOUT = 1.8V.)
Turn-On Time
Turn-On Time
VOUT = 1.2V (500mV/div)
IL = 1.5A, COUT = 10μF CER
VOUT = 1.2V (500mV/div)
IL = 0A, COUT = 10μF CER
VIN = 3.0V (2V/div)
VIN = 3.0V (2V/div)
Time (10μs/div)
Time (10μs/div)
Load Transient Response
90
80
70
60
50
40
30
20
10
0
VIN = 3.3V
COUT =10μF CER
VOUT = 1.8V (50mV/div)
V
V
I
= 3.3V
IN
OUT
= 1.8V
= 1A
OUT
C
C
= 1µF CER
= 1µF CER
IN
OUT
ILOAD = 100mA to 1.5A (1A/div)
100
1k
10k
100k
1M
FREQUENCY (kHz)
PSRR
Time (40μs/div)
6 of 14
www.diodes.com
December 2012
© Diodes Incorporated
AP7363
Document number: DS35059 Rev. 8 - 2
AP7363
Application Note
Input Capacitor
A minimum 2.2μF ceramic capacitor is recommended between IN and GND pins to decouple input power supply glitch and noise. The amount of
the capacitance may be increased without limit. Larger input capacitor like 10μF will provide better load transient response. This input capacitor
must be located as close as possible to the device to assure input stability and reduce noise. For PCB layout, a wide copper trace is required for
both IN and GND pins. A lower ESR capacitor type allows the use of less capacitance, while higher ESR type requires more capacitance.
Output Capacitor
The output capacitor is required to stabilize and help the transient response of the LDO. The AP7363 is stable with any type of capacitor, with no
limitations on minimum or maximum ESR. The device is designed to have excellent transient response for most applications with a small amount
of output capacitance. The device is also stable with multiple capacitors in parallel, which can be of any type of value. Additional capacitance
helps to reduce undershoot and overshoot during transient loads. This capacitor should be placed as close as possible to OUT and GND pins for
optimum performance.
Adjustable Operation
The AP7363 provides output voltage from 0.6V to 5.0V through external resistor divider as shown below.
The output voltage is calculated by:
⎛
⎜
⎞
⎟
R
1
V
= V
REF
1+
OUT
⎜
⎝
⎟
⎠
R
2
Where VREF = 0.6V (the internal reference voltage)
Rearranging the equation will give the following that is used for adjusting the output to a particular voltage:
⎛
⎜
⎞
V
OUT
⎟
−1
R = R
1
2
⎜
⎝
⎟
V
REF
⎠
To maintain the stability of the internal reference voltage, R2 need to be kept smaller than 10kΩ.
No Load Stability
Other than external resistor divider, no minimum load is required to keep the device stable. The device will remain stable and regulated in no
load condition.
7 of 14
www.diodes.com
December 2012
© Diodes Incorporated
AP7363
Document number: DS35059 Rev. 8 - 2
AP7363
Application Note (cont.)
Stability and Phase Margin
Any regulator which operates using a feedback loop must be compensated in such a way as to ensure adequate phase margin, which is defined
as the difference between the phase shift and -180 degrees at the frequency where the loop gain crosses unity (0 dB). For most LDO regulators,
the ESR of the output capacitor is required to create a zero to add enough phase lead to ensure stable operation. The AP7363 has a internal
compensation circuit which maintains phase margin regardless of the ESR of the output capacitor, any type of capacitos can be used.
The two charts on the next page show the gain/phase plot of the AP7363 with an output of 1.2V, 10μF ceramic output capacitor, delivering 1.5A
load current and no load. It can be seen the phase margin is about 90° (which is very stable).
120
100
80
60
40
20
0
140
120
100
80
140
120
100
80
120
100
80
PHASE
PHASE
GAIN
60 GAIN
40
20
0
60
60
40
20
0
40
20
0
-20
-40
-60
-20
-40
VIN = 2.7V
VOUT = 1.2V
IL = 0A
-20
-40
-60
-80
V
V
= 2.7V
-20
-40
-60
-80
IN
-60
-80
= 1.2V
OUT
-80
-100
-120
I
= 1.5A
L
COUT = 10µF CER
C
= 10µF CER
OUT
-100
-120
100
1k
10k
FREQUENCY(Hz)
Gain-Bandwidth Plot for no Load
100k
1M
100
1k
10k
FREQUENCY(Hz)
Gain-Bandwidth Plot for 1.5A Load
100k
1M
Short Circuit Protection
When output current at OUT pin is higher than current limit threshold, the current limit protection will be triggered and clamp the output current to
prevent over-current and to protect the regulator from damage due to overheating.
Thermal Shutdown Protection
Thermal protection disables the output when the junction temperature rises to approximately +170°C, allowing the device to cool down. When the
junction temperature reduces to approximately +160°C the output circuitry is enabled again. Depending on power dissipation, thermal resistance,
and ambient temperature, the thermal protection circuit may cycle on and off. This cycling limits the heat dissipation of the regulator, protecting it
from damage due to overheating.
Low Quiescent Current
The AP7363, consuming only around 0.5mA for all input range, provides great power saving in portable and low power applications.
Output Noise
This is the integrated value of the output noise over a specified frequency range. Input voltage and output load current are kept constant during
the measurement. Results are expressed in µVrms or µV√Hz.
The AP7363 is a low noise regulator and needs no external noise reduction capacitor. Output voltage noise is typically 100μVrms overall noise
level between 100 Hz and 100 kHz.
Noise is specified in two ways:
Output noise density is the RMS sum of all noise sources, measured at the regulator output, at a specific frequency (measured with a 1Hz
bandwidth). This type of noise is usually plotted on a curve as a function of frequency.
Output noise voltage is the RMS sum of spot noise over a specified bandwidth. Spot noise is measured in units μV/√Hz or nV/√Hz and total
output noise is measured in μV(rms). The primary source of noise in low-dropout regulators is the internal reference.
8 of 14
www.diodes.com
December 2012
© Diodes Incorporated
AP7363
Document number: DS35059 Rev. 8 - 2
AP7363
Application Note (cont.)
Power Dissipation
The device power dissipation and proper sizing of the thermal plane that is connected to the thermal pad is critical to avoid thermal shutdown and
ensure reliable operation. Power dissipation of the device depends on input voltage and load conditions and can be calculated by:
PD = (VIN - VOUT) X IOUT
The maximum power dissipation, handled by the device, depends on the junction to ambient thermal resistance, and maximum ambient
temperature, which can be calculated by the equation in the following:
(+150°C - T )
A
PD _ max
=
R
θJA
Ordering Information
7”/13” Tape and Reel
Packaging
(Note 9)
Part Number
Package Code
Quantity
Part Number Suffix
AP7363-XXHA-7
AP7363-XXSP-13
AP7363-XXE-13
AP7363-XXD-13
HA
SP
E
U-DFN2030-8
SO-8EP
3000/Tape & Reel
2500/Tape & Reel
2500/Tape & Reel
2500/Tape & Reel
-7
-13
-13
-13
SOT223-3L
TO252-3L
D
Note:
9. TO252 and SOT223 are only available with fixed output version.
Marking Information
(1) U-DFN2030-8
Device
Package
Identification Code
AP7363ADJ
AP7363-10
AP7363-12
AP7363-15
AP7363-18
AP7363-25
AP7363-33
U-DFN2030-8
U-DFN2030-8
U-DFN2030-8
U-DFN2030-8
U-DFN2030-8
U-DFN2030-8
U-DFN2030-8
SA
SB
SC
SD
SE
SF
SG
9 of 14
www.diodes.com
December 2012
© Diodes Incorporated
AP7363
Document number: DS35059 Rev. 8 - 2
AP7363
Marking Information (cont.)
(2) SO-8EP
(3) SOT223
(4) TO252
10 of 14
www.diodes.com
December 2012
© Diodes Incorporated
AP7363
Document number: DS35059 Rev. 8 - 2
AP7363
Package Outline Dimensions (All dimensions in mm.)
Please see AP02002 at http://www.diodes.com/datasheets/ap02002.pdf for latest version.
(1) U-DFN2030-8
A
A1
A3
U-DFN2030-8
Dim Min Max Typ
Seating Plane
A
A1
A3
b
0.57 0.63 0.60
0
-
0.05 0.02
0.15
D
-
L
0.20 0.30 0.25
1.95 2.05 2.00
e
D
D2 1.40 1.60 1.50
(Pin #1 ID)
e
-
-
0.50
E
2.95 3.05 3.00
E2 1.50 1.70 1.60
C'0.25*45°
L
Z
0.35 0.45 0.40
0.125
E2
E
-
-
D2
All Dimensions in mm
Z
b
(2) SO-8EP
SO-8EP (SOP-8L-EP)
Dim Min Max Typ
Exposed Pad
A
1.40 1.50 1.45
8
1
5
4
A1 0.00 0.13
-
b
C
D
E
0.30 0.50 0.40
0.15 0.25 0.20
4.85 4.95 4.90
3.80 3.90 3.85
E1
H
F
E0 3.85 3.95 3.90
E1 5.90 6.10 6.00
b
Bottom View
E
e
F
H
L
-
-
1.27
2.75 3.35 3.05
2.11 2.71 2.41
0.62 0.82 0.72
9° (All sides)
N
45°
7°
Q
C
N
Q
-
-
0.35
4° ± 3°
A
Gauge Plane
Seating Plane
0.60 0.70 0.65
All Dimensions in mm
e
E0
A1
L
D
11 of 14
www.diodes.com
December 2012
© Diodes Incorporated
AP7363
Document number: DS35059 Rev. 8 - 2
AP7363
Package Outline Dimensions (cont.) (All dimensions in mm.)
Please see AP02002 at http://www.diodes.com/datasheets/ap02002.pdf for latest version.
(3) SOT223
SOT223
Dim Min Max Typ
A
1.55 1.65 1.60
A1 0.010 0.15 0.05
b1
b2
C
D
E
E1
e
e1
L
2.90 3.10 3.00
0.60 0.80 0.70
0.20 0.30 0.25
6.45 6.55 6.50
3.45 3.55 3.50
6.90 7.10 7.00
—
—
—
—
4.60
2.30
0.85 1.05 0.95
0.84 0.94 0.89
Q
All Dimensions in mm
A
A1
(4) TO252
TO252
Dim Min Max Typ
E
b3
A
c2
A
2.19 2.39 2.29
L3
D
A1 0.00 0.13 0.08
A2 0.97 1.17 1.07
b
0.64 0.88 0.783
E1
A2
b2 0.76 1.14 0.95
b3 5.21 5.46 5.33
c2 0.45 0.58 0.531
H
D
6.00 6.20 6.10
D1 5.21
−
−
−
L4
A1
e
2.286
−
E
6.45 6.70 6.58
E1 4.32
L
−
−
H
L
9.40 10.41 9.91
1.40 1.78 1.59
e
3X b
2X b2
a
L3 0.88 1.27 1.08
L4 0.64 1.02 0.83
a
0°
10°
−
All Dimensions in mm
12 of 14
www.diodes.com
December 2012
© Diodes Incorporated
AP7363
Document number: DS35059 Rev. 8 - 2
AP7363
Suggested Pad Layout
Please see AP02001 at http://www.diodes.com/datasheets/ap02001.pdf for the latest version.
(1) U-DFN2030-8
X2
Y
C
Value
(in mm)
0.500
0.250
0.350
1.500
1.850
0.600
1.600
3.300
Dimensions
C
G
X
X1
X2
Y
Y1
Y2
Y2
Y1
X1
G
Pin1
X
(2) SO-8EP
X2
Value
Dimensions
(in mm)
1.270
0.802
3.502
4.612
1.505
2.613
6.500
C
X
X1
X2
Y
Y1
Y2
X1
Y1
Y2
Y
C
X
(3) SOT223
X1
Y1
Dimensions Value (in mm)
X1
X2
Y1
Y2
C1
C2
3.3
1.2
1.6
1.6
6.4
2.3
C1
Y2
C2
X2
(4) TO252
X2
Dimensions
Value (in mm)
Z
11.6
1.5
7.0
2.5
7.0
6.9
2.3
X1
X2
Y1
Y2
C
Y2
Z
C
E1
Y1
X1
E1
13 of 14
www.diodes.com
December 2012
© Diodes Incorporated
AP7363
Document number: DS35059 Rev. 8 - 2
AP7363
IMPORTANT NOTICE
DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
(AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION).
Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes
without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the
application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or
trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume
all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated
website, harmless against all damages.
Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel.
Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and
hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or
indirectly, any claim of personal injury or death associated with such unintended or unauthorized application.
Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings
noted herein may also be covered by one or more United States, international or foreign trademarks.
This document is written in English but may be translated into multiple languages for reference. Only the English version of this document is the
final and determinative format released by Diodes Incorporated.
LIFE SUPPORT
Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express
written approval of the Chief Executive Officer of Diodes Incorporated. As used herein:
A. Life support devices or systems are devices or systems which:
1. are intended to implant into the body, or
2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the
labeling can be reasonably expected to result in significant injury to the user.
B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the
failure of the life support device or to affect its safety or effectiveness.
Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any
use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related
information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its
representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems.
Copyright © 2012, Diodes Incorporated
www.diodes.com
14 of 14
www.diodes.com
December 2012
© Diodes Incorporated
AP7363
Document number: DS35059 Rev. 8 - 2
相关型号:
AP7363-25HA-7
Fixed Positive LDO Regulator, 2.5V, 0.28V Dropout, BIPolar, PDSO8, 2 X 3 MM, GREEN, UDFN-8
DIODES
AP7363-33E-13
Fixed Positive LDO Regulator, 3.3V, 0.28V Dropout, BIPolar, PDSO3, GREEN, SOT-223, 4 PIN
DIODES
AP7363-33HA-7
Fixed Positive LDO Regulator, 3.3V, 0.28V Dropout, BIPolar, PDSO8, 2 X 3 MM, GREEN, UDFN-8
DIODES
AP7363-33SP-13
Fixed Positive LDO Regulator, 3.3V, 0.28V Dropout, BIPolar, PDSO8, GREEN, SOP-8
DIODES
©2020 ICPDF网 联系我们和版权申明