ZLDO1117QGTA [DIODES]
Adjustable Positive LDO Regulator, 1.25V Min, 5V Max, BIPolar,;
| 型号： | ZLDO1117QGTA |
| 厂家： | 
DIODES INCORPORATED |
| 描述： | Adjustable Positive LDO Regulator, 1.25V Min, 5V Max, BIPolar, 输出元件 调节器 |
| 文件： | 总14页 (文件大小：430K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
A Product Line of
Diodes Incorporated
ZLDO1117
1A LOW DROPOUT POSITIVE REGULATOR
1.2V, 1.5V, 1.8V, 2.5V, 3.3V, 5.0V AND ADJUSTABLE OUTPUTS
Description
Pin Assignments
ZLDO1117 is a low dropout positive adjustable or fixed-mode
regulator with 1A output current capability.
SOT223
The ZLDO1117 has a 2% tolerance across the industrial temperature
range and is guaranteed to have lower than 1.2V dropout at full load
current making it ideal to provide well-regulated outputs of 1.2V to
5.0V with input supply voltages up to 18V.
The ZLDO1117 is ideally suited to provide well-regulated supplies for
low voltage IC applications such as high-speed bus termination and
low current 3.3V logic supply across the whole industrial temperature
range.
TO252
(Top View)
3
Features
Vin
•
•
•
•
•
•
•
•
•
•
•
1.2V Maximum Dropout at Full Load Current
2% Tolerance Over Temperature, Line and Load Variations
Fast Transient Response
2
Vout
Adj (GND)
1
Tab is Vout
Output Current Limiting
Built-in Thermal Shutdown
Good Noise Rejection
Suitable for use with MLCC Capacitors
Qualified to AEC-Q100 Grade 2 (see ‘Ordering Information’)
PPAP capable (Note 4)
-40 to +125°C Junction Temperature Range
Available in TO252 and SOT223 with “Green” Molding Compound
(No Br, Sb)
Lead-Free Finish; RoHS Compliant (Notes 1 & 2)
Halogen and Antimony Free. “Green” Device (Note 3)
Notes:
1. EU Directive 2002/95/EC (RoHS) & 2011/65/EU (RoHS 2) compliant. All applicable RoHS exemptions applied.
2. See http://www.diodes.com for more information about Diodes Incorporated’s definitions of Halogen- and Antimony-free, "Green" and Lead-free.
3. Halogen- and Antimony-free "Green” products are defined as those which contain <900ppm bromine, <900ppm chlorine (<1500ppm total Br + Cl)
and <1000ppm antimony compounds.
4. Automotive products are AEC-Q100 qualified and are PPAP capable. Automotive, AEC-Q100 and standard products are electrically and thermally
the same, except where specified.
Typical Applications Circuit
1A I/O – 1.8V Core Regulator
ZLDO1117-18
3.3V
1.8V
4.7µF
MLCC
4.7µF
MLCC
1 of 14
www.diodes.com
July 2012
© Diodes Incorporated
ZLDO1117
Document number: DS32018 Rev. 6 - 2
A Product Line of
Diodes Incorporated
ZLDO1117
Pin Descriptions
Pin
I/O
Pin
Number
Function
Name
A resistor divider from this pin to the VOUT pin and ground sets the output voltage (Ground only for
Fixed-Mode).
Adj (GND)
VOUT
I
1
The output of the regulator. A minimum of 4.7µF capacitor (0.05Ω ≤ ESR ≤ 0.5Ω) must be connected
from this pin to ground to insure stability. For improved ac load response a larger output capacitor is
recommended.
O
2
The input pin of regulator. Typically a large storage capacitor (0.05Ω ≤ ESR ≤ 0.5Ω) is connected from
this pin to ground to ensure that the input voltage does not sag below the minimum dropout voltage
during the load transient response. This pin must always be 1.3V higher than VOUT in order for the
device to regulate properly.
VIN
I
3
Absolute Maximum Ratings (@TA = +25°C, unless otherwise specified.)
Symbol
VIN
Parameter
Input Supply Voltage (Relative to Ground)
Junction Temperature
Rating
-0.03 to +18
+150
Unit
V
°C
TJ
Power Dissipation
Storage Temperature
See SOA Curve
-65 to +150
TST
°C
Unless otherwise stated voltages specified are relative to the ANODE pin.
1.2
1
0.8
0.6
SOA
0.4
0.2
0
0
5
10
15
20
25
VIN - VOUT (V)
Safe Operation Area (SOA) Curve
ESD Susceptibility
Symbol
Parameter
Rating
4
400
Unit
kV
V
HBM
MM
Human Body Model
Machine Model
Stresses greater than the 'Absolute Maximum Ratings' specified above, may cause permanent damage to the device. These are stress ratings only; functional
operation of the device at these or any other conditions exceeding those indicated in this specification is not implied. Device reliability may be affected by exposure to
absolute maximum rating conditions for extended periods of time.
Semiconductor devices are ESD sensitive and may be damaged by exposure to ESD events. Suitable ESD precautions should be taken when handling and
transporting these devices
2 of 14
www.diodes.com
July 2012
© Diodes Incorporated
ZLDO1117
Document number: DS32018 Rev. 6 - 2
A Product Line of
Diodes Incorporated
ZLDO1117
Recommended Operating Conditions (@TA = +25°C, unless otherwise specified.)
Symbol
Parameter
Min
2.7 (Note 8)
0.01
Max
18
Unit
V
VIN
IO
Input voltage
Output current
1
A
TJ
Operating Junction Temperature Range (Note 5)
-40
+125
°C
Package Thermal Data
Thermal Resistance
Package
SOT223 (Note 6)
TO252 (Note 7)
Rating
Unit
107
73
Junction-to-Ambient, θJA
Junction-to-Case, θJC
°C/W
SOT223 (Note 6)
TO252 (Note 7)
16
12
°C/W
Notes:
5. ZLDO1117 contains an internal thermal limiting circuit that is designed to protect the regulator in the event that the maximum junction temperature
exceeded. When activated, typically at 150°C, the regulator Output switches off and then back on as the die cools.
6. Test condition for SOT223: TA = +27°C, no air flow, device mounted on 2”X2” polyimide PCB, 2 oz copper, 5.6mmX5.6mm pad.
7. Test condition for TO252: TA = +27°C, no air flow, device mounted on 2”X2” polyimide PCB, 1 oz copper, 2cmX2cm pad.
8. Ensures correct operation without entering dropout. Device will continue to operate below this minimum input voltage under dropout conditions.
Electrical Characteristics (@TA = +25°C, unless otherwise specified.)
Parameter
Conditions
TA
Min
Typ
Max
Unit
V
(VIN-VOUT) = 2V, IO = 10mA
25
1.238
1.250
1.263
Reference Voltage
ZLDO1117-ADJ
VOUT+1.4V < VIN< 10V,
10mA < IO< 1A
FT
1.225
1.275
IO = 10mA, VIN = 3.2V
25
FT
25
FT
25
FT
25
FT
25
FT
25
FT
25
FT
25
FT
1.188
1.176
1.485
1.470
1.782
1.764
2.475
2.450
3.267
3.235
4.95
1.200
1.500
1.800
2.500
3.300
5.000
1.212
1.224
1.515
1.530
1.818
1.836
2.525
2.550
3.333
3.365
5.05
V
ZLDO1117-1.2
ZLDO1117-1.5
ZLDO1117-1.8
ZLDO1117-2.5
ZLDO1117-3.3
ZLDO1117-5.0
10mA< IO< 1A, 2.7V <VIN< 12V
IO = 10mA, VIN = 3.5V
V
V
0 < IO< 1A, 2.9V <VIN< 12V
IO = 10mA, VIN = 3.8V
0 < IO< 1A, 3.2V <VIN< 12V
IO = 10mA, VIN = 4.5V
Output Voltage
V
0 < IO< 1A, 3.9V <VIN< 12V
IO = 10mA, VIN = 5.3V
V
0 < IO< 1A, 4.7V <VIN < 12V
IO = 10mA, VIN = 7V
V
0 < IO< 1A, 6.4V <VIN < 12V
4.900
5.100
0.1
ZLDO1117-ADJ
ZLDO1117-1.2
IO = 10mA,
VOUT+1.5V<VIN<12V
%
%
0.2
Line Regulation
0.1
IO = 0mA,
VOUT+1.5V<VIN<12V
ZLDO1117-xx
0.2
Notes:
9. See thermal regulation specifications for changes in output voltage due to heating effects. Line and load regulation are measured at a constant
junction temperature by low duty cycle pulse testing. Load regulation is measured at the output lead = 1/18” from the package.
10. Line and load regulation are guaranteed up to the maximum power dissipation of 15W. Power dissipation is determined by the difference between input
and output differential and the output current. Guaranteed maximum power dissipation will not be available over the full input/output range.
3 of 14
www.diodes.com
July 2012
© Diodes Incorporated
ZLDO1117
Document number: DS32018 Rev. 6 - 2
A Product Line of
Diodes Incorporated
ZLDO1117
Electrical Characteristics (cont.) (@TA = +25°C, unless otherwise specified.)
Parameter
Conditions
TA
25
Min
Typ
Max
0.2
0.4
0.2
0.4
3
Unit
%
VIN=3.3V,VADJ=0, 10mA<IO<1A,
(Notes 9, 10)
ZLDO1117-ADJ
ZLDO1117-1.2
ZLDO1117-1.5
ZLDO1117-1.8
ZLDO1117-2.5
ZLDO1117-3.3
ZLDO1117-5.0
FT
25
%
VIN=2.7V, 10mA < IO < 1A,
(Notes 9, 10)
FT
VIN = 3V, 0 < IO< 1A,
(Notes 9, 10)
25
mV
mV
mV
mV
mV
FT
6
VIN = 3.3V, 0 < IO< 1A,
(Notes 9, 10)
25
4
Load Regulation
FT
8
VIN = 4V, 0 < IO< 1A,
(Notes 9, 10)
25
5
FT
10
6.6
13
10
20
1.2
1.3
1.35
VIN = 4.8V, 0 < IO< 1A,
(Notes 9, 10)
25
FT
VIN = 6.5V, 0 < IO< 1A,
(Notes 9, 10)
25
FT
25
1.11
ZLDO1117-
ADJ/1.2/1.5/1.8/2.5/
3.3/5.0
Dropout Voltage
0 ~ 125
FT
IO = 1A, ΔVOUT = 1%VOUT
V
A
(VIN-VOUT
)
ZLDO1117-
ADJ/1.2/1.5/1.8/2.5/
3.3/5.0
25
FT
Current Limit
(VIN-VOUT) = 5V
1. 1
ZLDO1117-ADJ
ZLDO1117-1.2
Minimum Load Current
(Note 8)
VIN = <18V
FT
FT
FT
25
25
2
4
5
mA
mA
µA
ZLDO1117-xx
VIN< 18V, IO = 0mA
VIN = 7V
Quiescent current
10
ZLDO1117-ADJ
ZLDO1117-1.2
GND current
35
120
0.1
30ms pulse
Thermal Regulation
Ripple Rejection
Temperature Stability
%/W
dB
f = 120Hz, COUT = 25µF Tantalum,
IOUT = 100mA, ZLDO1117-XXX VIN = VOUT+3V
60
80
IO = 10mA
0.5
%
Notes:
8. See thermal regulation specifications for changes in output voltage due to heating effects. Line and load regulation are measured at a constant
junctiontemperature by low duty cycle pulse testing. Load regulation is measured at the output lead = 1/18” from the package.
9. Line and load regulation are guaranteed up to the maximum power dissipation of 15W. Power dissipation is determined by the difference between input
and output differential and the output current. Guaranteed maximum power dissipation will not be available over the full input/output range.
4 of 14
www.diodes.com
July 2012
© Diodes Incorporated
ZLDO1117
Document number: DS32018 Rev. 6 - 2
A Product Line of
Diodes Incorporated
ZLDO1117
Typical Characteristics
0.5
0.06
0.05
0.04
0.03
0.02
0.01
0
0.4
Adjustable version
ILOAD = 10mA
0.3
VOUT+1.5V<VIN<12V, IOUT=10mA
0.2
0.1
0
-0.1
-0.2
-0.3
-0.4
-0.5
-40
-25
-10
5
20
35
50
65
80
95
110
125
-0.01
Temperature (°C)
-50
-25
0
25
50
75
100
125
Temperature (C)
Output Voltage Variation vs. Temperature
Line Regulation vs. Temperature
0.25
0.2
1.4
1.3
1.2
1.1
1
VIN=3.3V, 10mA<IOUT<1A
TJ = 25ºC
∆VOUT = 1% of VOUT
0.15
0.1
0.9
0.8
0.7
0.6
0.05
0
-50
-25
0
25
50
75
100
125
0
0.2
0.4
0.6
0.8
1
IOUT (A)
Temperature (°C)
Load Regulation vs. Temperature
Drop-Out Voltage vs. Current
70
60
50
40
30
20
10
0
Dropout vs Temperature
1.4
1.3
1.2
1.1
1
IOUT=1A
∆VOUT = 1% of VOUT
0.9
0.8
-50
-25
0
25
50
75
100
125
-50
-25
0
25
50
75
100
125
Temperature (°C)
Temperature (°C)
Drop-Out Voltage vs. Temperature
Adjust Pin Input Current
5 of 14
www.diodes.com
July 2012
© Diodes Incorporated
ZLDO1117
Document number: DS32018 Rev. 6 - 2
A Product Line of
Diodes Incorporated
ZLDO1117
Typical Characteristics
ZLDO1117-2.5V
CIN = 1µF, COUT = 10µFTANT
IPRELOAD = 100mA, Istep = 500mA
ZLDO1117-2.5V
CIN = 1µF, COUT = 4.7µF MLCC
IPRELOAD = 100mA, ISTEP = 500mA
10mV
0
10mV
0
-10mV
-10mV
600mA
100mA
600mA
100mA
Transient Load Regulation with 10µF Tantalum
Capacitor
Transient Load Regulation with 4.7µF MLCC Capacitor
ZLDO1117 2.5V
CIN = 1µF, COUT = 4.7µF MLCC
ILOAD = 100mA
10
0
5V
4V
10µs/div
Transient Line Regulation with 4.7µF MLCC Capacitor
90
85
80
75
70
65
60
55
50
ILOAD = 100mA, VIN - VOUT = 3V
10
100
1,000
Frequency (Hz)
10,000
100,000
Ripple Rejection
6 of 14
www.diodes.com
July 2012
© Diodes Incorporated
ZLDO1117
Document number: DS32018 Rev. 6 - 2
A Product Line of
Diodes Incorporated
ZLDO1117
Application Information
The ZLDO1117 family of quasi-LDO regulators is easy to use. They are protected against short circuit and thermal overloads. (see block
diagram).
Thermal protection circuitry will shut down the regulator should the junction temperature exceed +150°C at the sense point. The ZLDO1117 is
pin compatible with similar ‘1117 regulators and offers extended temperature range and improved regulation specifications.
Operation
The ZLDO1117 develops a 1.25V reference voltage between the output and the adjust terminal (see block diagram). By placing a resistor
between these two terminals, a constant current is caused to flow through R1 and down through R2. For fixed output variants Resistors R1 and
R2 are internal.
Stability
The ZLDO1117 requires an output capacitor as part of the device frequency compensation. As part of its improved performance over industry
standard 1117 the ZLDO1117 is suitable for use with MLCC (Multi Layer Ceramic Chip) capacitors. A minimum of 4.7µF ceramic X7R, 4.7µF
tantalum, or 47 µF of aluminum electrolytic is required. The ESR of the output capacitor should be less than 0.5Ω. Surface mount tantalum
capacitors, which have very low ESR, are available from several manufacturers. When using MLCC capacitors avoid the use of Y5V dielectrics.
Load Regulation
For improved load regulation the ZLDO1117-ADJ should have the upper feedback resistor, R1, connected as close as possible to VOUT and the
lower resistor, R2, connected as close as possible to the load GND return. This helps reduce any parasitic resistance in series with the load.
Thermal Considerations
ZLDO1117 series regulators have internal thermal limiting circuitry designed to protect the device during overload conditions. For continuous
normal load conditions however, the maximum junction temperature rating of +125°C must not be exceeded.
It is important to give careful consideration to all sources of thermal resistance from junction to ambient. For the SOT223-3L and TO252-3L
packages, which are designed to be surface mounted, additional heat sources mounted near the device must also be considered. Heat sinking is
accomplished using the heat spreading capability of the PCB and its copper traces. The θJC (junction to tab)of the TO252-3L and SOT223-3L are
+12°C/W and +16°C/W respectively.
Thermal resistances from tab to ambient can be as low as +30°C/W. The total thermal resistance from junction to ambient can be as low as
+42 to +46°C/W. This requires a reasonable sized PCB with at least one layer of copper to spread the heat across the board and couple it into
the surrounding air. Datasheet specifications using 2 oz copper and a 5mmx5mm pad with TA = +27°C, no air flow yielded θJA (junction to tab) of
+73°C/W and +107°C/W for TO252-3L and SOT223-3L respectively.
The thermal resistance for each application will be affected by thermal interactions with other components on the board. Some experimentation
will be necessary to determine the actual value.
Ripple Rejection
When using the ZLDO1117 adjustable device the adjust terminal can be bypassed to improve ripple rejection. When the adjust terminal is
bypassed the required value of the output capacitor increases.
The device will require an output capacitor of 22µF tantalum or 150µF aluminum electrolytic when the adjust pin is bypassed. Normally, capacitor
values on the order of 100µF are used in the output of many regulators to ensure good load transient response with large load current changes.
Output capacitance can be increased without limit and larger values of output capacitance further improve stability and transient response.
The curves for Ripple Rejection were generated using an adjustable device with the adjust pin bypassed. These curves will hold true for all
values of output voltage. For proper bypassing, and ripple rejection approaching the values shown, the impedance of the adjust pin capacitor, at
the ripple frequency, should be < R1. R1 is normally in the range of 100Ω to 200Ω. The size of the required adjust pin capacitor is a function of
the input ripple frequency. At 120Hz, with R1 = 100Ω, the adjust pin capacitor should be >13µF. At 10kHz only 0.16µF is needed.
For fixed voltage devices, and adjustable devices without an adjust pin capacitor, the output ripple will increase as the ratio of the output voltage
to the reference voltage (VOUT/VREF). For example, with the output voltage equal to 5V, the output ripple will be increased by the ratio of 5V/1.25V.
It will increase by a factor of four. Ripple rejection will be degraded by 12dB from the value shown on the curve.
7 of 14
www.diodes.com
July 2012
© Diodes Incorporated
ZLDO1117
Document number: DS32018 Rev. 6 - 2
A Product Line of
Diodes Incorporated
ZLDO1117
Typical Application Circuits
Using
⎧
R2
R1
⎫
⎬
⎭
VOUT = 1.25 • 1+
⎨
⎩
then the output voltage becomes:
⎧
330
110
⎫
⎬
⎭
VOUT = 1.25 • 1+
= 5.0V
⎨
⎩
Figure 1 Basic Adjustable Regulator with 5V Output
Figure 2 Adjustable Regulator with IADJ Errors
⎧
R2
R1
⎫
⎬
⎭
VOUT = 1.25 • 1+
+ IADJ •R2
⎨
⎩
Because IADJ typically is 55μA, its effect is negligible in most applications.
⎧
330
110
⎫
VOUT = 1.25 • 1+
+ 55 •10−6 • 330 = 5.02V ~ 0.4%
⎨
⎬
⎭
⎩
A. Output capacitor selection is critical for regulator stability. Larger Cout values benefit the regulator by improving transient response and loop
stability.
B. CADJ can be used to improve ripple rejection. If CADJ is used, a Cout that is larger in value than CADJ must be used.
C. Cin is recommended if ZLDO1117 is not located near the power supply filter.
D. An external diode is recommended to protect the regulator if the input instantaneously is shorted to GND.
E. This device is designed to be stable with tantalum and MLCC capacitors with an ESR less than 0.47Ω.
8 of 14
www.diodes.com
July 2012
© Diodes Incorporated
ZLDO1117
Document number: DS32018 Rev. 6 - 2
A Product Line of
Diodes Incorporated
ZLDO1117
Other Application Circuits
Figure 3 ZLDO1117 with Extended Output Voltage
ZLDO1117
OUT
VOUT
VIN
IN
R1
121Ω
1%
ADJ
C1
10 F
C2
100 F
T1
MMBT3904
TTL
R2
365Ω
1%
R3
1k
R4
1k
Figure 4 ZLDO1117 with Disable Function
ZLDO1117x50
IN OUT
AC
IN
ADJ
C1
C2
10 F
100 F
VOUT = -5V
Figure 5 ZLDO1117 as a Negative LDO
9 of 14
www.diodes.com
July 2012
© Diodes Incorporated
ZLDO1117
Document number: DS32018 Rev. 6 - 2
A Product Line of
Diodes Incorporated
ZLDO1117
Ordering Information
Packaging
(Note 11)
Part Number
Output Voltage
Status
Reel Quantity
Tape width
Reel size
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
Active
16 mm
12 mm
16 mm
12 mm
16 mm
12 mm
16 mm
12 mm
16 mm
12 mm
16 mm
12 mm
16 mm
12 mm
16 mm
12 mm
16 mm
12 mm
16 mm
12 mm
16 mm
12 mm
16 mm
12 mm
16 mm
12 mm
16 mm
12 mm
ZLDO1117KTC
ZLDO1117GTA
TO252
SOT223
TO252
2500
1000
2500
1000
2500
1000
2500
1000
2500
1000
2500
1000
2500
1000
2500
1000
2500
1000
2500
1000
2500
1000
2500
1000
2500
1000
2500
1000
13”
7”
Adjustable
1.2V
13”
7”
ZLDO1117K12TC
ZLDO1117G12TA
ZLDO1117K15TC
ZLDO1117G15TA
ZLDO1117K18TC
ZLDO1117G18TA
ZLDO1117K25TC
ZLDO1117G25TA
ZLDO1117K33TC
ZLDO1117G33TA
ZLDO1117K50TC
ZLDO1117G50TA
ZLDO1117QKTC
ZLDO1117QGTA
ZLDO1117QK12TC
ZLDO1117QG12TA
ZLDO1117QK15TC
ZLDO1117QG15TA
ZLDO1117QK18TC
ZLDO1117QG18TA
ZLDO1117QK25TC
ZLDO1117QG25TA
ZLDO1117QK33TC
ZLDO1117QG33TA
ZLDO1117QK50TC
ZLDO1117QG50TA
SOT223
TO252
13”
7”
1.5V
SOT223
TO252
13”
7”
1.8V
SOT223
TO252
13”
7”
2.5V
SOT223
TO252
13”
7”
3.3V
SOT223
TO252
13”
7”
5.0V
SOT223
TO252
13”
7”
Adjustable
1.2V
SOT223
TO252
13”
7”
SOT223
TO252
13”
7”
1.5V
SOT223
TO252
13”
7”
1.8V
SOT223
TO252
13”
7”
2.5V
SOT223
TO252
13”
7”
3.3V
SOT223
TO252
13”
7”
5.0V
SOT223
Note:
11. Pad layout as shown on Diodes Inc. suggested pad layout document AP02001, which can be found on our website at
http://www.diodes.com/datasheets/ap02001.pdf.
10 of 14
www.diodes.com
July 2012
© Diodes Incorporated
ZLDO1117
Document number: DS32018 Rev. 6 - 2
A Product Line of
Diodes Incorporated
Marking Information
TO252
SOT223
11 of 14
www.diodes.com
July 2012
© Diodes Incorporated
ZLDO1117
Document number: DS32018 Rev. 6 - 2
A Product Line of
Diodes Incorporated
ZLDO1117
Package Outline Dimensions (All dimensions in mm.)
SOT223
SOT223
Dim Min Max Typ
A
1.55 1.65 1.60
A1 0.010 0.15 0.05
b1
b2
C
D
E
E1
e
e1
L
2.90 3.10 3.00
0.60 0.80 0.70
0.20 0.30 0.25
6.45 6.55 6.50
3.45 3.55 3.50
6.90 7.10 7.00
—
—
—
—
4.60
2.30
0.85 1.05 0.95
0.84 0.94 0.89
Q
All Dimensions in mm
A
A1
TO252
TO252
Dim Min Max Typ
E
b3
A
2.19 2.39 2.29
A
A1 0.00 0.13 0.08
A2 0.97 1.17 1.07
c2
L3
b
0.64 0.88 0.783
b2 0.76 1.14 0.95
b3 5.21 5.46 5.33
c2 0.45 0.58 0.531
E1
A2
D
H
D
6.00 6.20 6.10
D1 5.21
−
−
−
e
2.286
−
E
6.45 6.70 6.58
L4
A1
E1 4.32
−
−
H
L
9.40 10.41 9.91
1.40 1.78 1.59
L
e
L3 0.88 1.27 1.08
L4 0.64 1.02 0.83
3X b
2X b2
a
a
0°
10°
−
All Dimensions in mm
12 of 14
www.diodes.com
July 2012
© Diodes Incorporated
ZLDO1117
Document number: DS32018 Rev. 6 - 2
A Product Line of
Diodes Incorporated
ZLDO1117
Suggested Pad Layout
SOT223
X1
Dimensions Value (in mm)
X1
X2
Y1
Y2
C1
C2
3.3
1.2
1.6
1.6
6.4
2.3
Y1
C1
Y2
C2
X2
TO252
X2
Dimensions
Value (in mm)
Z
11.6
1.5
7.0
2.5
7.0
6.9
2.3
Y2
X1
X2
Y1
Y2
C
Z
C
E1
Y1
X1
E1
13 of 14
www.diodes.com
July 2012
© Diodes Incorporated
ZLDO1117
Document number: DS32018 Rev. 6 - 2
A Product Line of
Diodes Incorporated
ZLDO1117
IMPORTANT NOTICE
DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
(AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION).
Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes
without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the
application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or
trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume
all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated
website, harmless against all damages.
Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel.
Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and
hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or
indirectly, any claim of personal injury or death associated with such unintended or unauthorized application.
Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings
noted herein may also be covered by one or more United States, international or foreign trademarks.
LIFE SUPPORT
Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express
written approval of the Chief Executive Officer of Diodes Incorporated. As used herein:
A. Life support devices or systems are devices or systems which:
1. are intended to implant into the body, or
2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the
labeling can be reasonably expected to result in significant injury to the user.
B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the
failure of the life support device or to affect its safety or effectiveness.
Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any
use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related
information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its
representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems.
Copyright © 2012, Diodes Incorporated
www.diodes.com
14 of 14
www.diodes.com
July 2012
© Diodes Incorporated
ZLDO1117
Document number: DS32018 Rev. 6 - 2
相关型号：
ZLDO1117QK12TC
AUTOMOTIVE COMPLIANT 1A LOW DROPOUT POSITIVE REGULATOR WITH FIXED AND ADJUSTABLE OUTPUTS
DIODES
ZLDO1117QK15TC
AUTOMOTIVE COMPLIANT 1A LOW DROPOUT POSITIVE REGULATOR WITH FIXED AND ADJUSTABLE OUTPUTS
DIODES
ZLDO1117QK18TC
AUTOMOTIVE COMPLIANT 1A LOW DROPOUT POSITIVE REGULATOR WITH FIXED AND ADJUSTABLE OUTPUTS
DIODES
ZLDO1117QK25TC
AUTOMOTIVE COMPLIANT 1A LOW DROPOUT POSITIVE REGULATOR WITH FIXED AND ADJUSTABLE OUTPUTS
DIODES
ZLDO1117QK33TC
AUTOMOTIVE COMPLIANT 1A LOW DROPOUT POSITIVE REGULATOR WITH FIXED AND ADJUSTABLE OUTPUTS
DIODES
ZLDO1117QK50TC
AUTOMOTIVE COMPLIANT 1A LOW DROPOUT POSITIVE REGULATOR WITH FIXED AND ADJUSTABLE OUTPUTS
DIODES
©2020 ICPDF网 联系我们和版权申明