12M103G [DUBILIER]
RESISTOR NETWORK SIL; 电阻网络SIL
| 型号： | 12M103G |
| 厂家： | 
DUBILIER |
| 描述： | RESISTOR NETWORK SIL |
| 文件： | 总2页 (文件大小：120K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
RESISTORS
RESISTOR NETWORK SIL
Low-profile
Epoxy dipped
5 to 13-pin
The Dubilier range of SIL networks features 2% accuracy in a low-
cost package.
The low-profile epoxy package allows the device to be used in
locations where moulded parts do not fit.
Isolated and common-terminal designs are available, allowing the
simple, reliable insertion of up to 12 resistors at once.
OUTLINE DRAWING
2.5 max
L max
PIN 1
Marking
9E-103G
5.2 max
3.0 ± 0.5
0.5 ± 0.1
3.0 ± 0.1
2.54
± 0.25
No of Pins
L max
5
6
7
8
9
10
11
12
13
12.7 15.3 17.8 20.4 22.9 25.4 28.0 30.5 33.1
RANGE & TOLERANCES
Parameter
Performance
0.125W
Limits
@ 70°C
Power Rating per Element
Temperature Range
Resistance Range
Resistance Tolerance
Temperature Coefficient
-55˚ to +125°C
33Ω to 1MΩ
2% (G)
Derating linearly from 70°C
E - 24 series
100 ppm/°C
250ppm/˚C
100V
50Ω ≥ 2.2MΩ
<50Ω – 2.2MΩ
Max Working Voltage
Max Overload Voltage
200V
ORDERING INFORMATION
9
E
103
G
N° Pins
Type
Value
Tolerance
5 to 13
M = Isolated
E = Common
3 digit code :
Last digit is
2%
decade multiplier.
First two digits are
first digits of value.
135
Fax: 01371 875075 www.dubilier.co.uk Tel: 01371 875758
RESISTORS
RESISTOR NETWORK SIL
SPECIFICATION
Short Term Overload
Vibration
∆R/R (1% + 0.05Ω)
After application of 21/2 x rated voltage, or the maximum overload voltage, whichever smaller, for a period of 5
secs. Resistance change to be within specification, with no evidence of arcing, burning or charring.
∆R/R (0.5% + 0.5Ω)
Resistors are to be subjected to vibration of amplitude 0.8mm for 2 hours in each of three mutually
perpendicular directions. The vibration frequency shall be swept from 10 to 55 to 10Hz in 1 minute.
Resistance change to be within specification with no evidence of damage.
Components shall withstand twice their rated voltage for 1 minute applied between termination and substrate. No
evidence of arcing, burning or charring.
Dielectric Strength
Solderability
∆R/R (1% + 0.05Ω)
After dipping at 260°C 5°C for 10 seconds, resistance change to be within specification, with no evidence of
arcing, burning or charring. Terminations shall maintain a minimum of 75% coverage following the procedures of
MIL-STD-202E.
Load Life
∆R/R (2% + 0.05Ω)
After 1000 hours application of the rated voltage with a duty cycle of 11/2 hours ON and 1/2 hour OFF, at
70°C. Resistance change to be within specification, with no evidence of arcing, burning or charring.
∆R/R (2% + 0.05Ω)
Moisture Load
After 1000 hours application of the rated voltage with a duty cycle of 11/2 hours ON and 1/2 hour OFF, at
40°C and 90-95% RH. Resistance change to be within specification, with no evidence of arcing, burning
or charring.
Voltage Coefficient
Flammability
∆R/R < 100ppm/V
Product is conformally coated with epoxy resin conforming to UL94V-0.
SIL PIN-OUTS
Common (E)
Common parts are characterised by having a number of resistive
elements, all of the same nominal value. All elements are connected to pin 1.
6
7
2
3
4
5
8
n-1
1
n = Number of pins
Isolated (M)
Isolated parts are characterised by having a number of resistive
elements, all of the same nominal value. All elements are independent.
n
4
2
3
n-1
1
6
5
n = Number of pins
136
Fax: 01371 875075 www.dubilier.co.uk Tel: 01371 875758
相关型号：
©2020 ICPDF网 联系我们和版权申明