R3G500-AG34-63F [EBMPAPST]
EC centrifugal fans;
| 型号： | R3G500-AG34-63F |
| 厂家： | 
ebm-papst |
| 描述： | EC centrifugal fans |
| 文件： | 总2页 (文件大小：1452K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
EC centrifugal fans
backward curved, single inlet, Ø 500
Highlights:
– 9-blade fan, 3-phase fan motor
– Output: 10 VDC, max.10 mA, 20 VDC, max. 50 mA, slave 0-10 V
– Input: sensor 0-10 V or 4-20 mA, 24 V external programming, 0-10 VDC/ PWM control
– Integrated PID controller along with RS485 MODBUS RTU technology
– Over-temperature protected electronics / motor
– Soft start, alarm relay, motor current limit, PFC passive, line undervoltage / phase failure detection
– Control interface with SELV potential safely disconnected from the mains
Material: Impeller: Aluminum sheet
Rotor: Coated in black
Electronic housing: Die-cast aluminum
Assembly: Galvanized steel with aluminum posts
Mounting position: Shaft horizontal or rotor on bottom; rotor on top on request
Condensate discharge holes: Rotor-side
Nominal Data
Type
RadiPac
Motor
CFM
VAC
Hz
Watts
RPM
A
°C
lbs
Yes
Yes
R3G500-AG34-63F
EG1R-240-500-30 M3G150-FF
EG1R-480-500-30 M3G150-FF
6,450
6,450
200...240
380...480
50/60
50/60
2,700
2,500
1,700
1,700
7.8
3.3
-25...55
-25...60
50
50
IP54
IP54
A
A
R3G500-AG25-64F
(1) Nominal data at maximum load.
I
A
(460V)
I
n
Pe
W
L Ain
w
A
Curves
rpm
dB(A)
(230V)
Measurement: LU-134784
Measurement: LU-116713
Measurement: LU-118204
Measurement: LU-118205
Measurement: LU-118206
1
2
3
4
1700
1700
1700
1700
1909
2329
2700
2382
2.4
3.0
3.3
2.7
5.7
6.9
7.2
7.0
91
86
82
81
900
850
800
750
700
650
600
550
500
450
400
350
300
250
Air performance measured as per:
ISO 5801, Installation category
A, without protection against
accidental contact.
5
6
7
8
1400
1400
1400
1400
1065
1294
1436
1323
1.3
1.6
1.8
1.4
3.2
3.8
4.2
3.9
87
82
78
77
Suction-side noise levels: L A as
W
per ISO 13347, L A measured at
P
1m distance to fan axis.
9
1100
1100
1100
1100
516
628
697
642
0.7
0.9
0.9
0.8
1.5
1.8
2.0
1.9
82
77
73
72
The values given are valid
10
11
12
under the measuring conditions
mentioned and may vary accoring
to the actual installation situation.
With any deviation to the standard
set-up, the specific values have
to be checked and reviewed once
installed or fitted.
200
150
100
50
6
5
13
14
15
16
800
199
0.4
0.6
75
p
4
800
800
800
241
268
247
0.5
0.5
0.5
0.7
0.8
0.7
70
66
65
f
s
[
P
p
a
]
p
f
f
s
s
[
[
P
P
For detailed information on the
measuring set-up, please contact
ebm-papst.
]
3
0
1.000
2.000
3.000
4.000
5.000
6.000
7.000
cfm
/h
m
3
1.000
3.000
5.000
7.000
9.000
11.000
13.000
Dimensions shown in inches (mm)
R3G500-AGXX-XXF
Depth of screw max. 25mm
M10 (14x)
Tightening torque
+
3.5 0.5 Nm
Cable diameter: min. 4 mm,
max. 10 mm; tightening torque:
+
(
)
4
0.6 Nm
-
.08 2
2
(
)
(
)
)
Ø9.13 232
6.89 175
(
)
+
0.3
2.95 75
(
)
(
Ø9.92 252
9.17 233
(
)
+
2
)
9.80 249
2.76 70
(
)
(
Ø10.83 275
Accessory part:
Inlet nozzle 63072-2-4013
not included in the standard
scope of delivery.
(
)
0.20 5
Dimensions shown in inches (mm)
EGIR-XXX-500-30
(
)
13.99 355.4
(
)
22.835 580
(
Ø 0.433 11)
8 PLACES
(
)
12.365 314.07
相关型号：
©2020 ICPDF网 联系我们和版权申明