E13D8H2F-156.250M [ECLIPTEK]
CRYSTAL OSCILLATOR, CLOCK, 156.25MHz, LVPECL OUTPUT, ROHS COMPLIANT, CERAMIC, SMD, 6 PIN;
| 型号： | E13D8H2F-156.250M |
| 厂家： | 
Ecliptek |
| 描述： | CRYSTAL OSCILLATOR, CLOCK, 156.25MHz, LVPECL OUTPUT, ROHS COMPLIANT, CERAMIC, SMD, 6 PIN 机械 输出元件 振荡器 |
| 文件： | 总5页 (文件大小：182K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
RoHS
Pb
E13D8H2F-156.250M
E13D8 H 2 F -156.250M
Series
Nominal Frequency
RoHS Compliant (Pb-free) 6 Pad 5mm x 7mm Ceramic
SMD 3.3 LVPECL Oscillator
156.250MHz
Logic Control / Additional Output
Tri-State (High Impedance) and Complementary Output
Frequency Tolerance/Stability
±50ppm Maximum over -40°C to +85°C
Duty Cycle
50 ±5(%)
ELECTRICAL SPECIFICATIONS
Nominal Frequency
156.250MHz
Frequency Tolerance/Stability
±50ppm Maximum over -40°C to +85°C (Inclusive of all conditions: Calibration Tolerance at 25°C,
Frequency Stability over the Operating Temperature Range, Supply Voltage Change, Output Load Change,
1st Year Aging at 25°C, Shock, and Vibration)
Supply Voltage
3.3Vdc ±5%
Input Current
75mA Maximum (with Load)
Output Voltage Logic High (Voh)
Output Voltage Logic Low (Vol)
Peak to Peak Output Voltage Swing
Rise/Fall Time
Vcc-1.4Vdc Minimum, Vcc-1.2Vdc Typical, Vcc-0.9Vdc Maximum
Vcc-1.7Vdc Maximum, Vcc-1.85Vdc Typical, Vcc-2.0Vdc Minimum
600mVdc Minimum, 800mVdc Typical, 1000mVdc Maximum
300pSec Typical, 600pSec Maximum (Measured over 20% to 80% of waveform)
50 ±5(%) (Measured at 50% of waveform)
50 Ohms into Vcc-2.0Vdc
Duty Cycle
Load Drive Capability
Output Logic Type
LVPECL
Phase Noise
-60dBc/Hz at 10Hz Offset, -90dBc/Hz at 100Hz Offset, -115dBc/Hz at 1kHz Offset, -129dBc/Hz at 10kHz
Offset, -130dBc/Hz at 100kHz Offset, -131dBc/Hz at 1MHz Offset, -148dBc/Hz at 10MHz Offset (All Values
are Typical, Fo = 156.250MHz)
Logic Control / Additional Output
Tri-State Input Voltage (Vih and Vil)
Tri-State (High Impedance) and Complementary Output
Enable High Option: Vih of 70% of Vcc Minimum or No Connect to Enable Output and Complementary
Output, Vil of 30% of Vcc Maximum to Disable Output and Complementary Output (High Impedance).
Standby Current
600µA Maximum (Disabled Output, High Impedance, without Load)
0.7pSec Typical, 1pSec Maximum (FJ=12kHz to 20MHz)
10mSec Maximum
RMS Phase Jitter
Start Up Time
Storage Temperature Range
-55°C to +125°C
ENVIRONMENTAL & MECHANICAL SPECIFICATIONS
Fine Leak Test
MIL-STD-883, Method 1014, Condition A
MIL-STD-883, Method 1014, Condition C
MIL-STD-202, Method 213, Condition C
MIL-STD-202, Method 210
Gross Leak Test
Mechanical Shock
Resistance to Soldering Heat
Resistance to Solvents
Solderability
MIL-STD-202, Method 215
MIL-STD-883, Method 2003
Temperature Cycling
Vibration
MIL-STD-883, Method 1010
MIL-STD-883, Method 2007, Condition A
www.ecliptek.com | Specification Subject to Change Without Notice | Rev B 2/13/2010 | Page 1 of 5
E13D8H2F-156.250M
MECHANICAL DIMENSIONS (all dimensions in millimeters)
PIN CONNECTION
1
2
3
4
5
6
Tri-State
No Connect
5.00
±0.15
2.60 ±0.15
1.2 ±0.2
Case/Ground
Output
2.00
MAX
Complementary Output
Supply Voltage
1
2
6
5
4
2.54
TYP
7.00
±0.15
LINE MARKING
5.08
±0.15
1
2
3
ECLIPTEK
156.25M
3
XXYZZ
XX=Ecliptek Manufacturing
Code
Y=Last Digit of the Year
ZZ=Week of the Year
1.4
±0.1
Suggested Solder Pad Layout
All Dimensions in Millimeters
1.80 (X6)
2.00 (X6)
0.54 (X4)
Solder Land
2.39 (X3)
(X6)
All Tolerances are ±0.1
www.ecliptek.com | Specification Subject to Change Without Notice | Rev B 2/13/2010 | Page 2 of 5
E13D8H2F-156.250M
Test Circuit for Tri-State and Complementary Output
50 Ohms
Frequency
Counter
Oscilloscope
Pin Connections
1 Tri-State
2 No Connect
3 Ground
4 Output
Power
Supply
Probe 2 Probe 1
(Note 2) (Note 2)
5 Complementary Output
Supply
Voltage
6 Supply Voltage (VDD
)
(VDD
)
Output
50 Ohms
Current
Meter
Complementary
Output
0.01µF
(Note 1)
0.1µF
(Note 1)
Switch
Ground
Power
Supply
Voltage
Meter
Power
Supply
Power
Supply
Tri-State
No
Connect
Note 1: An external 0.1µF low frequency tantalum bypass capacitor in parallel with a 0.01µF high frequency
ceramic bypass capacitor close to the package ground and VDD pin is required.
Note 2: A low capacitance (<12pF), 10X attenuation factor, high impedance (>10Mohms), and high bandwidth
(>300MHz) passive probe is recommended.
www.ecliptek.com | Specification Subject to Change Without Notice | Rev B 2/13/2010 | Page 3 of 5
E13D8H2F-156.250M
Recommended Solder Reflow Methods
Critical Zone
TL to TP
TP
Ramp-up
Ramp-down
TL
TS Max
TS Min
tL
tP
tSPreheat
t 25°C to Peak
Time (t)
High Temperature Infrared/Convection
TS MAX to TL (Ramp-up Rate)
3°C/second Maximum
Preheat
- Temperature Minimum (TS MIN)
- Temperature Typical (TS TYP)
- Temperature Maximum (TS MAX)
- Time (tS MIN)
150°C
175°C
200°C
60 - 180 Seconds
Ramp-up Rate (TL to TP)
3°C/second Maximum
Time Maintained Above:
- Temperature (TL)
- Time (tL)
217°C
60 - 150 Seconds
Peak Temperature (TP)
260°C Maximum for 10 Seconds Maximum
250°C +0/-5°C
Target Peak Temperature (TP Target)
Time within 5°C of actual peak (tp)
Ramp-down Rate
20 - 40 seconds
6°C/second Maximum
8 minutes Maximum
Level 1
Time 25°C to Peak Temperature (t)
Moisture Sensitivity Level
www.ecliptek.com | Specification Subject to Change Without Notice | Rev B 2/13/2010 | Page 4 of 5
E13D8H2F-156.250M
Recommended Solder Reflow Methods
Critical Zone
TL to TP
TP
Ramp-up
Ramp-down
TL
TS Max
TS Min
tL
tP
tSPreheat
t 25°C to Peak
Time (t)
Low Temperature Infrared/Convection 240°C
TS MAX to TL (Ramp-up Rate)
5°C/second Maximum
Preheat
- Temperature Minimum (TS MIN)
- Temperature Typical (TS TYP)
- Temperature Maximum (TS MAX)
- Time (tS MIN)
N/A
150°C
N/A
60 - 120 Seconds
Ramp-up Rate (TL to TP)
5°C/second Maximum
Time Maintained Above:
- Temperature (TL)
- Time (tL)
150°C
200 Seconds Maximum
Peak Temperature (TP)
240°C Maximum
Target Peak Temperature (TP Target)
Time within 5°C of actual peak (tp)
Ramp-down Rate
240°C Maximum 1 Time / 230°C Maximum 2 Times
10 seconds Maximum 2 Times / 80 seconds Maximum 1 Time
5°C/second Maximum
Time 25°C to Peak Temperature (t)
Moisture Sensitivity Level
N/A
Level 1
Low Temperature Manual Soldering
185°C Maximum for 10 seconds Maximum, 2 times Maximum.
High Temperature Manual Soldering
260°C Maximum for 5 seconds Maximum, 2 times Maximum.
www.ecliptek.com | Specification Subject to Change Without Notice | Rev B 2/13/2010 | Page 5 of 5
相关型号：
E13D8H2F-156.250MTR
CRYSTAL OSCILLATOR, CLOCK, 156.25MHz, LVPECL OUTPUT, ROHS COMPLIANT, CERAMIC, SMD, 6 PIN
ECLIPTEK
E13D8H2F-159.375MTR
CRYSTAL OSCILLATOR, CLOCK, 159.375MHz, LVPECL OUTPUT, ROHS COMPLIANT, CERAMIC, SMD, 6 PIN
ECLIPTEK
E13D8H2F-212.500M
CRYSTAL OSCILLATOR, CLOCK, 212.5MHz, LVPECL OUTPUT, ROHS COMPLIANT, CERAMIC, SMD, 6 PIN
ECLIPTEK
E13D8H2F-250.000M
CRYSTAL OSCILLATOR, CLOCK, 250MHz, LVPECL OUTPUT, ROHS COMPLIANT, CERAMIC, SMD, 6 PIN
ECLIPTEK
E13D8H2F-312.500M
CRYSTAL OSCILLATOR, CLOCK, 312.5MHz, LVPECL OUTPUT, ROHS COMPLIANT, CERAMIC, SMD, 6 PIN
ECLIPTEK
E13D8H2F-312.500MTR
CRYSTAL OSCILLATOR, CLOCK, 312.5MHz, LVPECL OUTPUT, ROHS COMPLIANT, CERAMIC, SMD, 6 PIN
ECLIPTEK
E13D8H2F-75.000M
CRYSTAL OSCILLATOR, CLOCK, 75MHz, LVPECL OUTPUT, ROHS COMPLIANT, CERAMIC, SMD, 6 PIN
ECLIPTEK
©2020 ICPDF网 联系我们和版权申明