E15C5H2F-80.000MTR [ECLIPTEK]
CRYSTAL OSCILLATOR, CLOCK, 80MHz, LVPECL OUTPUT, ROHS COMPLIANT, CERAMIC, SMD, 6 PIN;
| 型号： | E15C5H2F-80.000MTR |
| 厂家： | 
Ecliptek |
| 描述： | CRYSTAL OSCILLATOR, CLOCK, 80MHz, LVPECL OUTPUT, ROHS COMPLIANT, CERAMIC, SMD, 6 PIN 机械 输出元件 振荡器 |
| 文件： | 总6页 (文件大小：233K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
RoHS
Pb
E15C5H2F-80.000M TR
E15C5 H 2 F -80.000M TR
Series
Packaging Options
RoHS Compliant (Pb-free) 2.5V 6 Pad 3.2mm x 5mm
Ceramic SMD LVPECL Oscillator
Tape & Reel
Nominal Frequency
Frequency Tolerance/Stability
±50ppm Maximum over -40°C to +85°C
80.000MHz
Logic Control / Additional Output
Tri-State and Complementary Output
Duty Cycle
50 ±5(%)
ELECTRICAL SPECIFICATIONS
Nominal Frequency
80.000MHz
Frequency Tolerance/Stability
±50ppm Maximum over -40°C to +85°C (Inclusive of all conditions: Calibration Tolerance (at 25°C),
Frequency Stability over the Operating Temperature Range, Supply Voltage Change, Output Load Change,
1st Year Aging at 25°C, and Vibration)
Supply Voltage
+2.5Vdc ±5%
Input Current
75mA Maximum
Output Voltage Logic High (Voh)
Output Voltage Logic Low (Vol)
Rise/Fall Time
Vcc-1.025Vdc Minimum from 0°C to +85°C, Vcc-1.085Vdc Minimum from -40°C to 0°C
Vcc-1.405Vdc Maximum from 0°C to +85°C, Vcc-1.305Vdc Maximum from -40°C to 0°C
300pSec Typical, 700pSec Maximum (Measured at 20% to 80% of Waveform)
50 ±5(%) (Measured at 50% of Waveform)
Duty Cycle
Load Drive Capability
Output Logic Type
Phase Noise
50 Ohms into Vcc-2.0Vdc
LVPECL
-60dBc/Hz at 10Hz Offset, -95dBc/Hz at 100Hz Offset, -125dBc/Hz at 1kHz Offset, -143dBc/Hz at 10kHz
Offset, -145dBc/Hz at 100kHz Offset, -145dBc/Hz at 1MHz Offset, -146dBc/Hz at 10MHz Offset (All Values
are Typical, Fo=156.250MHz)
Logic Control / Additional Output
Tri-State Input Voltage (Vih and Vil)
Tri-State and Complementary Output
Vih of 70% of Vcc Minimum or No Connect to Enable Output and Complementary Output, Vil of 30% of Vcc
Maximum to Disable High Impedance Output and Complementary Output
Standby Current
30µA Maximum (Without Load)
0.4pSec Typical, 1pSec Maximum (Fj=12kHz to 20MHz)
10mSec Maximum
RMS Phase Jitter
Start Up Time
Storage Temperature Range
-55°C to +125°C
ENVIRONMENTAL & MECHANICAL SPECIFICATIONS
ESD Susceptibility
MIL-STD-883, Method 3015, Class 1, HBM: 1500V
MIL-STD-883, Method 1014, Condition A
UL94-V0
Fine Leak Test
Flammability
Gross Leak Test
Mechanical Shock
Moisture Resistance
Moisture Sensitivity
Resistance to Soldering Heat
Resistance to Solvents
Solderability
MIL-STD-883, Method 1014, Condition C
MIL-STD-883, Method 2002, Condition B
MIL-STD-883, Method 1004
J-STD-020, MSL 1
MIL-STD-202, Method 210, Condition K
MIL-STD-202, Method 215
MIL-STD-883, Method 2003
Temperature Cycling
Vibration
MIL-STD-883, Method 1010, Condition B
MIL-STD-883, Method 2007, Condition A
www.ecliptek.com | Specification Subject to Change Without Notice | Rev B 8/12/2010 | Page 1 of 6
E15C5H2F-80.000M TR
MECHANICAL DIMENSIONS (all dimensions in millimeters)
PIN CONNECTION
1
2
3
4
5
6
Tri-State
3.20
1.30
1.20
±0.15
No Connect
±0.15
MAX
Case/Ground
Output
6
5
4
1
2
3
Complementary Output
Supply Voltage
2.54
±0.15
5.00
±0.15
LINE MARKING
1
E80.000
E=Ecliptek Designator
2
XXYZZ
XX=Ecliptek Manufacturing
Code
Y=Last Digit of the Year
ZZ=Week of the Year
0.64
±0.10
1.27
±0.15
1.00
±0.15
Suggested Solder Pad Layout
All Dimensions in Millimeters
1.40 (X6)
1.00 (X6)
0.27 (X4)
Solder Land
0.80 (X2)
(X6)
All Tolerances are ±0.1
www.ecliptek.com | Specification Subject to Change Without Notice | Rev B 8/12/2010 | Page 2 of 6
E15C5H2F-80.000M TR
Test Circuit for Tri-State and Complementary Output
50 Ohms
Frequency
Counter
Oscilloscope
Pin Connections
1 Tri-State
2 No Connect
3 Ground
4 Output
Power
Supply
Probe 2 Probe 1
(Note 2) (Note 2)
5 Complementary Output
Supply
6 Supply Voltage (VDD
)
Voltage
(VDD
)
Output
50 Ohms
Current
Meter
Complementary
Output
0.01µF
(Note 1)
0.1µF
(Note 1)
Switch
Ground
Power
Supply
Voltage
Meter
Power
Supply
Power
Supply
Tri-State
No
Connect
Note 1: An external 0.01µF ceramic bypass capacitor in parallel with a 0.1µF high frequency ceramic bypass capacitor close (less than 2mm)
to the package ground and supply voltage pin is required.
Note 2: A low capacitance (<12pF), 10X attenuation factor, high impedance (>10Mohms), and high bandwidth (>500MHz) passive probe is
recommended.
Note 3: Test circuit PCB traces need to be designed for a characteristic line impedance of 50 ohms.
www.ecliptek.com | Specification Subject to Change Without Notice | Rev B 8/12/2010 | Page 3 of 6
E15C5H2F-80.000M TR
Tape & Reel Dimensions
Quantity Per Reel: 1,000 units
4.0 ±0.1
2.0 ±0.1
DIA 1.5 +0.1/-0.0
0.30 ±0.1
7.5 ±0.1
16.0 ±0.3
A0*
6.75 ±0.1
8.0 ±0.1
B0*
K0*
*Compliant to EIA 481A
1.5 MIN
22.4 MAX
DIA 40 MIN
Access Hole at
Slot Location
360 MAX
DIA 50 MIN
2.5 MIN Width
10.0 MIN Depth
Tape slot in Core
for Tape Start
DIA 20.2 MIN
DIA 13.0 ±0.2
16.4 +2.0/-0.0
www.ecliptek.com | Specification Subject to Change Without Notice | Rev B 8/12/2010 | Page 4 of 6
E15C5H2F-80.000M TR
Recommended Solder Reflow Methods
Critical Zone
TL to TP
TP
Ramp-up
Ramp-down
TL
TS Max
TS Min
tL
tP
tSPreheat
t 25°C to Peak
Time (t)
High Temperature Infrared/Convection
TS MAX to TL (Ramp-up Rate)
3°C/second Maximum
Preheat
- Temperature Minimum (TS MIN)
- Temperature Typical (TS TYP)
- Temperature Maximum (TS MAX)
- Time (tS MIN)
150°C
175°C
200°C
60 - 180 Seconds
Ramp-up Rate (TL to TP)
3°C/second Maximum
Time Maintained Above:
- Temperature (TL)
- Time (tL)
217°C
60 - 150 Seconds
Peak Temperature (TP)
260°C Maximum for 10 Seconds Maximum
250°C +0/-5°C
Target Peak Temperature (TP Target)
Time within 5°C of actual peak (tp)
Ramp-down Rate
20 - 40 seconds
6°C/second Maximum
8 minutes Maximum
Level 1
Time 25°C to Peak Temperature (t)
Moisture Sensitivity Level
www.ecliptek.com | Specification Subject to Change Without Notice | Rev B 8/12/2010 | Page 5 of 6
E15C5H2F-80.000M TR
Recommended Solder Reflow Methods
Critical Zone
TL to TP
TP
Ramp-up
Ramp-down
TL
TS Max
TS Min
tL
tP
tSPreheat
t 25°C to Peak
Time (t)
Low Temperature Infrared/Convection 240°C
TS MAX to TL (Ramp-up Rate)
5°C/second Maximum
Preheat
- Temperature Minimum (TS MIN)
- Temperature Typical (TS TYP)
- Temperature Maximum (TS MAX)
- Time (tS MIN)
N/A
150°C
N/A
60 - 120 Seconds
Ramp-up Rate (TL to TP)
5°C/second Maximum
Time Maintained Above:
- Temperature (TL)
- Time (tL)
150°C
200 Seconds Maximum
Peak Temperature (TP)
240°C Maximum
Target Peak Temperature (TP Target)
Time within 5°C of actual peak (tp)
Ramp-down Rate
240°C Maximum 1 Time / 230°C Maximum 2 Times
10 seconds Maximum 2 Times / 80 seconds Maximum 1 Time
5°C/second Maximum
Time 25°C to Peak Temperature (t)
Moisture Sensitivity Level
N/A
Level 1
Low Temperature Manual Soldering
185°C Maximum for 10 seconds Maximum, 2 times Maximum.
High Temperature Manual Soldering
260°C Maximum for 5 seconds Maximum, 2 times Maximum.
www.ecliptek.com | Specification Subject to Change Without Notice | Rev B 8/12/2010 | Page 6 of 6
相关型号：
E15C5H2F-80M
CRYSTAL OSCILLATOR, CLOCK, 80MHz, LVPECL OUTPUT, ROHS COMPLIANT, CERAMIC, SMD, 6 PIN
ECLIPTEK
E15C5H2F-90MTR
CRYSTAL OSCILLATOR, CLOCK, 90MHz, LVPECL OUTPUT, ROHS COMPLIANT, CERAMIC, SMD, 6 PIN
ECLIPTEK
E15C5J2F-100M
CRYSTAL OSCILLATOR, CLOCK, 100MHz, LVPECL OUTPUT, ROHS COMPLIANT, CERAMIC, SMD, 6 PIN
ECLIPTEK
E15C5J2F-100MTR
CRYSTAL OSCILLATOR, CLOCK, 100MHz, LVPECL OUTPUT, ROHS COMPLIANT, CERAMIC, SMD, 6 PIN
ECLIPTEK
E15C5J2F-120M
CRYSTAL OSCILLATOR, CLOCK, 120MHz, LVPECL OUTPUT, ROHS COMPLIANT, CERAMIC, SMD, 6 PIN
ECLIPTEK
E15C5J2F-120MTR
CRYSTAL OSCILLATOR, CLOCK, 120MHz, LVPECL OUTPUT, ROHS COMPLIANT, CERAMIC, SMD, 6 PIN
ECLIPTEK
E15C5J2F-122.888MTR
CRYSTAL OSCILLATOR, CLOCK, 122.888MHz, LVPECL OUTPUT, ROHS COMPLIANT, CERAMIC, SMD, 6 PIN
ECLIPTEK
E15C5J2F-124.400MTR
CRYSTAL OSCILLATOR, CLOCK, 124.4MHz, LVPECL OUTPUT, ROHS COMPLIANT, CERAMIC, SMD, 6 PIN
ECLIPTEK
E15C5J2F-124.4M
CRYSTAL OSCILLATOR, CLOCK, 124.4MHz, LVPECL OUTPUT, ROHS COMPLIANT, CERAMIC, SMD, 6 PIN
ECLIPTEK
E15C5J2F-124.4MTR
CRYSTAL OSCILLATOR, CLOCK, 124.4MHz, LVPECL OUTPUT, ROHS COMPLIANT, CERAMIC, SMD, 6 PIN
ECLIPTEK
©2020 ICPDF网 联系我们和版权申明