E2SEA14-16.000MTR [ECLIPTEK]

QUARTZ CRYSTAL RESONATOR, 16MHz, ROHS COMPLIANT, RESISTANCE WELDED, SMD, 2 PIN;


型号：	E2SEA14-16.000MTR
厂家：	Ecliptek
描述：	QUARTZ CRYSTAL RESONATOR, 16MHz, ROHS COMPLIANT, RESISTANCE WELDED, SMD, 2 PIN 驱动晶体谐振器
文件：	总5页 (文件大小：208K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

RoHS

E2SEA14-16.000M TR

E2S E A 14 -16.000M TR

Series

Packaging Options

RoHS Compliant (Pb-free) Resistance Welded

HC-49/UP SMD Crystal

Tape & Reel

Nominal Frequency

Frequency Tolerance/Stability

±30ppm at 25°C, ±50ppm over -20°C to +70°C

16.000MHz

Load Capacitance

14pF Parallel Resonant

Mode of Operation

AT-Cut Fundamental

ELECTRICAL SPECIFICATIONS

Nominal Frequency

Frequency Tolerance/Stability

Aging at 25°C

16.000MHz

±30ppm at 25°C, ±50ppm over -20°C to +70°C

±5ppm/year Maximum

14pF Parallel Resonant

7pF Maximum

Load Capacitance

Shunt Capacitance (C0)

Equivalent Series Resistance

Mode of Operation

50 Ohms Maximum

AT-Cut Fundamental

Drive Level

1mWatt Maximum

Storage Temperature Range

Insulation Resistance

-40°C to +125°C

500 Megaohms Minimum at 100Vdc

ENVIRONMENTAL & MECHANICAL SPECIFICATIONS

Fine Leak Test

MIL-STD-883, Method 1014 Condition A

MIL-STD-883, Method 1014 Condition C

Sn 2µm - 6µm

Gross Leak Test

Lead Termination

Mechanical Shock

Resistance to Soldering Heat

Resistance to Solvents

Solderability

MIL-STD-202, Method 213 Condition C

MIL-STD-202, Method 210

MIL-STD-202, Method 215

MIL-STD-883, Method 2003

Temperature Cycling

Vibration

MIL-STD-883, Method 1010

MIL-STD-883, Method 2007 Condition A

MECHANICAL DIMENSIONS (all dimensions in millimeters)

LINE MARKING

E16.000M

E=Ecliptek Designator

M=MHz

4.50

MAX

13.30 MAX

4.85

MAX

0.50 MIN (x2)

4.88 ±0.20

0.80 ±0.30 (x2)

11.60 MAX

NOTE: Coplanarity 0.360 MAX

www.ecliptek.com | Specification Subject to Change Without Notice | Rev F 8/12/2010 | Page 1 of 5

E2SEA14-16.000M TR

Suggested Solder Pad Layout

All Dimensions in Millimeters

5.5 (X2)

2.0 (X2)

4.0

Solder Land

(X2)

All Tolerances are ±0.1

www.ecliptek.com | Specification Subject to Change Without Notice | Rev F 8/12/2010 | Page 2 of 5

E2SEA14-16.000M TR

Tape & Reel Dimensions

Quantity Per Reel: 1,000 units

4.0 ±0.2

2.0 ±0.1

DIA 1.5 ±0.1

0.4 ±0.1

11.5 ±0.1

24.0 ±0.3

A0*

10.75 ±0.10

12.0 ±0.2

B0*

K0*

*Compliant to EIA 481A

1.5 MIN

30.4 MAX

DIA 40 MIN

Access Hole at

Slot Location

360 MAX

DIA 50 MIN

2.5 MIN Width

10.0 MIN Depth

Tape slot in Core

for Tape Start

DIA 20.2 MIN

DIA 13.0 ±0.2

24.4 +2.0/-0.0

www.ecliptek.com | Specification Subject to Change Without Notice | Rev F 8/12/2010 | Page 3 of 5

E2SEA14-16.000M TR

Recommended Solder Reflow Methods

Critical Zone

T_Lto T_P

T_P

Ramp-up

Ramp-down

T_L

T_SMax

T_SMin

t_L

t_P

t_SPreheat

t 25°C to Peak

Time (t)

High Temperature Infrared/Convection

TS MAX to TL (Ramp-up Rate)

3°C/second Maximum

Preheat

- Temperature Minimum (TS MIN)

- Temperature Typical (TS TYP)

- Temperature Maximum (TS MAX)

- Time (tS MIN)

150°C

175°C

200°C

60 - 180 Seconds

Ramp-up Rate (TL to TP)

3°C/second Maximum

Time Maintained Above:

- Temperature (TL)

- Time (tL)

217°C

60 - 150 Seconds

Peak Temperature (TP)

260°C Maximum for 10 Seconds Maximum

250°C +0/-5°C

Target Peak Temperature (TP Target)

Time within 5°C of actual peak (tp)

Ramp-down Rate

20 - 40 seconds

6°C/second Maximum

8 minutes Maximum

Level 1

Time 25°C to Peak Temperature (t)

Moisture Sensitivity Level

www.ecliptek.com | Specification Subject to Change Without Notice | Rev F 8/12/2010 | Page 4 of 5

E2SEA14-16.000M TR

Recommended Solder Reflow Methods

Critical Zone

T_Lto T_P

T_P

Ramp-up

Ramp-down

T_L

T_SMax

T_SMin

t_L

t_P

t_SPreheat

t 25°C to Peak

Time (t)

Low Temperature Infrared/Convection 245°C

TS MAX to TL (Ramp-up Rate)

5°C/second Maximum

Preheat

- Temperature Minimum (TS MIN)

- Temperature Typical (TS TYP)

- Temperature Maximum (TS MAX)

- Time (tS MIN)

N/A

150°C

N/A

30 - 60 Seconds

Ramp-up Rate (TL to TP)

5°C/second Maximum

Time Maintained Above:

- Temperature (TL)

- Time (tL)

150°C

200 Seconds Maximum

Peak Temperature (TP)

245°C Maximum

Target Peak Temperature (TP Target)

Time within 5°C of actual peak (tp)

Ramp-down Rate

245°C Maximum 2 Times / 230°C Maximum 1 Time

10 seconds Maximum 2 Times / 80 seconds Maximum 1 Time

5°C/second Maximum

Time 25°C to Peak Temperature (t)

Moisture Sensitivity Level

N/A

Level 1

Low Temperature Manual Soldering

185°C Maximum for 10 seconds Maximum, 2 times Maximum.

High Temperature Manual Soldering

260°C Maximum for 5 seconds Maximum, 2 times Maximum.

www.ecliptek.com | Specification Subject to Change Without Notice | Rev F 8/12/2010 | Page 5 of 5

相关型号：