EL1503ACM [ELANTEC]
Line Driver/Receiver,;型号: | EL1503ACM |
厂家: | ELANTEC SEMICONDUCTOR |
描述: | Line Driver/Receiver, 局域网 |
文件: | 总2页 (文件大小:55K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
EL1503AC - Product Brief
High Power Differential Line Driver
Features
General Description
• High power ADSL driver
The EL1503AC ADSL Line Driver contains two wideband high-volt-
age drivers which are ideally suited for both ADSL and HDSL2
• 39.2V differential output drive
P-P
into 22Ω
applications. They can supply a 39.2V signal into a 22Ω load while
P-P
exhibiting very low distortion. The EL1503AC also has a number of
power saving features. The IADJ pin can be used to set the maximum
supply current and the C and C pins can be used to digitally vary the
• 42.4V differential output drive
P-P
into 65Ω
nd rd
• Driver 2 /3 harmonics of
0
1
-66dBc/-72dBc at 2V into 100Ω
differential
supply current to one of four modes. These modes include full power,
low power, terminate only and power down.
P-P
• Supply current of 12.5mA per
amplifier
• Supply current control
• Power saving modes
• Standard surface-mount packages
• Ultra-small LPP package
The EL1503AC uses current-feedback type amplifiers, which achieve
a high slew rate while consuming moderate power. They retain their
frequency response over a wide range of externally set gains. The
EL1503AC operates on ±5V to ±12V supplies and consumes only
12.5mA per amplifier.
The device is supplied in a thermally-enhanced 20-pin SO (0.300”), a
thermally-enhanced 16-pin SO (0.150”), and the small footprint
(4x5mm) 24-pin LPP packages. Center pins on each side of the 20-pin
and 16-pin packages are used as ground connections and heat spread-
Applications
• ADSL line drivers
• HDSL2 line drivers
ers. The LPP package has the potential for a low θ (<40°C/W) and
JA
• Video distribution amplifiers
dissipates heat by means of a thermal pad that is soldered onto the
PCB. All package options are specified for operation over the full ----
-40°C to +85°C temperature range.
Ordering Information
Pin Configurations
Tape &
Part No.
Package
Reel
-
Outline #
MDP0027
MDP0027
MDP0046
MDP0046
MDP0046
MDP0027
MDP0027
MDP0027
EL1503ACM
20-Pin SO (0.300")
EL1503ACM-T13 20-Pin SO (0.300")
13”
-
EL1503ACL
24-Pin LPP
24-Pin LPP
EL1503ACL-T7
EL1503ACL-T13
EL1503ACS
7”
NC
NC
1
2
3
4
5
6
7
19 NC
18 NC
17 VS+
16 NC
15 NC
14 NC
13 GND
24-Pin LPP
13”
-
16-Pin SO (0.150”)
16-Pin SO (0.150”)
16-Pin SO (0.150”)
EL1503ACS-T7
EL1503AC-T13
7”
13”
VS-
NC
Thermal Pad
NC
NC
GND
Get FULL DATA SHEET
24-Pin LPP Top View
Pin Configurations continues on Page 3
Note: All information contained in this data sheet has been carefully checked and is believed to be accurate as of the date of publication; however, this data sheet cannot be a “controlled document”. Current revisions, if any, to these
specifications are maintained at the factory and are available upon your request. We recommend checking the revision level before finalization of your design documentation.
© 2001 Elantec Semiconductor, Inc.
EL1503AC - Product Brief
High Power Differential Line Driver
General Disclaimer
Specifications contained in this data sheet are in effect as of the publication date shown. Elantec, Inc. reserves the right to make changes in the cir-
cuitry or specifications contained herein at any time without notice. Elantec, Inc. assumes no responsibility for the use of any circuits described
herein and makes no representations that they are free from patent infringement.
WARNING - Life Support Policy
Elantec, Inc. products are not authorized for and should not be used
within Life Support Systems without the specific written consent of
Elantec, Inc. Life Support systems are equipment intended to sup-
port or sustain life and whose failure to perform when properly used
in accordance with instructions provided can be reasonably
Elantec Semiconductor, Inc.
675 Trade Zone Blvd.
Milpitas, CA 95035
Telephone: (408) 945-1323
(888) ELANTEC
expected to result in significant personal injury or death. Users con-
templating application of Elantec, Inc. Products in Life Support
Systems are requested to contact Elantec, Inc. factory headquarters
to establish suitable terms & conditions for these applications. Elan-
tec, Inc.’s warranty is limited to replacement of defective
components and does not cover injury to persons or property or
other consequential damages.
Fax:
(408) 945-9305
European Office: +44-118-977-6020
Japan Technical Center: +81-45-682-5820
Printed in U.S.A.
2
相关型号:
©2020 ICPDF网 联系我们和版权申明