概述
规格参数
数据手册EL5397CS-T7 概述
Triple 200MHz Fixed Gain Amplifier 三重200MHz的固定增益放大器 音频/视频放大器
EL5397CS-T7 规格参数
| 生命周期： | Transferred | 包装说明： | SOIC-16 |
| Reach Compliance Code： | unknown | 风险等级： | 5.65 |
| 商用集成电路类型： | VIDEO AMPLIFIER | JESD-30 代码： | R-PDSO-G16 |
| 功能数量： | 3 | 端子数量： | 16 |
| 封装主体材料： | PLASTIC/EPOXY | 封装形状： | RECTANGULAR |
| 封装形式： | SMALL OUTLINE | 认证状态： | Not Qualified |
| 表面贴装： | YES | 端子形式： | GULL WING |
| 端子位置： | DUAL | Base Number Matches： | 1 |
EL5397CS-T7 数据手册
通过下载EL5397CS-T7数据手册来全面了解它。这个PDF文档包含了所有必要的细节，如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载EL5397C - Preliminary
Triple 200MHz Fixed Gain Amplifier
Features
General Description
• Gain selectable (+1, -1, +2)
• 200MHz -3dB bandwidth (AV = 1,
2)
• 4mA supply current (per amplifier)
• Single and dual supply operation,
from 5V to 10V
The EL5397C is a triple channel, fixed gain amplifier with a band-
width of 200MHz, making these amplifiers ideal for today’s high
speed video and monitor applications. The EL5397C features integnal
gain setting resistors and can be configured in a gain of +1, -1 or +2.
The same bandwidth is seen in both gain-of-1 and gain-of-2
applications.
• Available in 16-pin QSOP package
• Single (EL5197C) available
• 400MHz, 9mA product available
(EL5196C, EL5396C)
With a supply current of just 4mA per amplifier and the ability to run
from a single supply voltage from 5V to 10V, these amplifiers are also
ideal for hand held, portable or battery powered equipment.
For applications where board space is critical, the EL5397C is offered
in the 16-pin QSOP package, as well as a 16-pin SO. The EL5397C is
specified for operation over the full industrial temperature range of ---
-40°C to +85°C.
Applications
• Battery-powered Equipment
• Hand-held, Portable Devices
• Video Amplifiers
• Cable Drivers
• RGB Amplifiers
• Test Equipment
• Instrumentation
• Current to Voltage Converters
Pin Configurations
16-Pin SO & QSOP
Ordering Information
Tape &
Reel
INA+
NC*
VS-
1
2
3
4
5
6
7
8
16 INA-
15 OUTA
14 VS+
13 OUTB
12 INB-
11 NC
Part No
EL5397CS
Package
16-Pin SO
Outline #
MDP0027
MDP0027
MDP0027
MDP0040
MDP0040
-
-
EL5397CS-T7
EL5397CS-T13
EL5397CU
16-Pin SO
7”
+
16-Pin SO
13”
-
16-Pin QSOP
16-Pin QSOP
EL5397CU-T13
13”
+
-
NC*
INB+
NC
+
-
NC*
INC+
10 OUTC
9
INC-
EL5397CS, EL5397CU
* This pin must be left disconnected
Note: All information contained in this data sheet has been carefully checked and is believed to be accurate as of the date of publication; however, this data sheet cannot be a “controlled document”. Current revisions, if any, to these
specifications are maintained at the factory and are available upon your request. We recommend checking the revision level before finalization of your design documentation.
© 2001 Elantec Semiconductor, Inc.
EL5397C - Preliminary
Triple 200MHz Fixed Gain Amplifier
Absolute Maximum Ratings (T = 25°C)
A
Values beyond absolute maximum ratings can cause the device to be pre-
maturely damaged. Absolute maximum ratings are stress ratings only
and functional device operation is not implied.
Power Dissipation
Pin Voltages
See Curves
VS- - 0.5V to VS+ +0.5V
-65°C to +150°C
-40°C to +85°C
Storage Temperature
Operating Temperature
Lead Temperature
Supply Voltage between VS+ and VS-
Maximum Continuous Output Current
Operating Junction Temperature
11V
50mA
125°C
260°C
Important Note:
All parameters having Min/Max specifications are guaranteed. Typ values are for information purposes only. Unless otherwise noted, all tests are at the
specified temperature and are pulsed tests, therefore: TJ = TC = TA
.
Electrical Characteristics
VS+ = +5V, VS- = -5V, RL = 150W, TA = 25°C unless otherwise specified.
Parameter
Description
Conditions
Min
Typ
Max
Unit
AC Performance
BW
-3dB Bandwidth
AV = +1
AV = +2
200
200
20
MHz
MHz
MHz
V/µs
ns
BW1
SR
ts
0.1dB Bandwidth
Slew Rate
VO = -2.5V to +2.5V, AV = +2
VOUT = -2.5V to +2.5V, AV = -1
f = 5MHz
1900
2100
12
0.1% Settling Time
CS
en
Channel Separation
67
dB
Input Voltage Noise
IN- input current noise
IN+ input current noise
Differential Gain Error
Differential Phase Error
4.8
17
nV/ÖHz
pA/ÖHz
pA/ÖHz
%
in-
in+
dG
dP
50
[1]
[1]
AV = +2
AV = +2
0.03
0.04
°
DC Performance
VOS
Offset Voltage
-10
1
5
10
mV
µV/°C
%
TCVOS
AE
Input Offset Voltage Temperature Coefficient
Gain Error
Measured from TMIN to TMAX
VO = -3V to +3V
-2
2
RF, RG
Internal RF and RG
320
400
480
W
Input Characteristics
CMIR
+IIN
-IIN
Common Mode Input Range
±3V
-60
±3.3V
1
V
+ Input Current
- Input Current
Input Resistance
Input Capacitance
60
30
µA
µA
kW
pF
-30
1
RIN
45
CIN
0.5
Output Characteristics
VO
Output Voltage Swing
RL = 150W to GND
RL = 1KW to GND
RL = 10W to GND
±3.4V
±3.8V
95
±3.7V
±4.0V
120
V
V
IOUT
Output Current
mA
Supply
IsON
Supply Current
No Load, VIN = 0V
3
4
5
2
mA
dB
PSRR
-IPSR
Power Supply Rejection Ratio
- Input Current Power Supply Rejection
DC, VS = ±4.75V to ±5.25V
DC, VS = ±4.75V to ±5.25V
55
-2
75
µA/V
1. Standard NTSC test, AC signal amplitude = 286mVp-p, f = 3.58MHz
2
EL5397C - Preliminary
Triple 200MHz Fixed Gain Amplifier
Typical Performance Curves
Frequency Response (Gain)
Frequency Response (Phase), All Gains
90
6
A =-1
V
A =2
V
0
-90
2
-2
A =1
V
-180
-270
-6
-10
-14
R =150W
L
R =150W
L
-360
1M
10M
100M
1G
1G
1G
1M
10M
100M
Frequency (Hz)
1G
Frequency (Hz)
Frequency Response for Various C
Group Delay vs Frequency
L
14
10
6
3.5
3
A =2
R =150W
L
V
A =2
V
2.5
2
22pF added
10pF added
1.5
1
2
A =1
V
0pF added
-2
0.5
0
R =150W
L
-6
1M
10M
100M
Frequency (Hz)
1M
10M
100M
1G
Frequency (Hz)
Frequency Response for Various Common-mode Input
Voltages
Transimpedance (ROL) vs Frequency
6
2
10M
1M
0
3V
-3V
0V
Phase
-90
-2
100k
10k
1k
-180
-270
-360
-6
Gain
-10
-14
A =2
V
R =150W
L
100
1k
1M
10M
100M
10k
100k
1M
10M
100
1G
Frequency (Hz)
Frequency (Hz)
3
EL5397C - Preliminary
Triple 200MHz Fixed Gain Amplifier
Typical Performance Curves
PSRR and CMRR vs Frequency
-3dB Bandwidth vs Supply Voltage
20
250
200
150
100
R =150W
L
PSRR+
0
-20
PSRR-
A =2
V
-40
A =-1
V
A =1
V
CMRR
-60
-80
10k
100k
1M
10M
100M
1G
5
6
7
8
9
10
Frequency (Hz)
Total Supply Voltage (V)
Peaking vs Supply Voltage
-3dB Bandwidth vs Temperature
5
4
3
2
1
0
300
250
200
150
100
50
A =-1
V
A =1
V
A =2
V
R =150W
R =150W
L
L
0
5
6
7
8
9
10
-40
10
60
110
160
Total Supply Voltage (V)
Ambient Temperature (°C)
Peaking vs Temperature
Voltage and Current Noise vs Frequency
1
0.8
0.6
0.4
0.2
0
1000
100
10
i +
n
i -
n
e
n
R =150W
L
1
-40
10
60
110
160
100
1000
10k
100k
1M
10M
Frequency (Hz)
Ambient Temperature (°C)
4
EL5397C - Preliminary
Triple 200MHz Fixed Gain Amplifier
Typical Performance Curves
Closed Loop Output Impedance vs Frequency
Supply Current vs Supply Voltage
100
10
10
1
8
6
4
2
0
0.1
0.01
0.001
100
1k
10k
100k
1M
10M 100M
1G
100
1
0
2
4
6
8
10
12
100
1
Frequency (Hz)
Supply Voltage (V)
2nd and 3rd Harmonic Distortion vs Frequency
Two-tone 3rd Order
Input Referred Intermodulation Intercept (IIP3)
-20
-30
-40
-50
-60
-70
-80
-90
25
20
15
10
5
A =+2
V
V
A =+2
L
V
=2V
OUT
P-P
R =150W
R =100W
L
2nd Order
Distortion
3rd Order
Distortion
0
A =+2
V
-5
R =100W
L
-10
1
10
Frequency (MHz)
10
Frequency (MHz)
Differential Gain/Phase vs DC Input
Voltage at 3.58MHz
Differential Gain/Phase vs DC Input
Voltage at 3.58MHz
0.03
0.02
0.01
0
0.04
0.03
0.02
0.01
0
A =2
A =1
V
F
V
dP
R =R =500W
R =750W
R =500W
L
F
G
dP
R =150W
L
dG
dG
-0.01
-0.02
-0.03
-0.04
-0.05
-0.01
-0.02
-0.03
-0.04
-1
-0.5
0
0.5
-1
-0.5
0
0.5
DC Input Voltage
DC Input Voltage
5
EL5397C - Preliminary
Triple 200MHz Fixed Gain Amplifier
Typical Performance Curves
Output Voltage Swing vs Frequency
THD<1%
Output Voltage Swing vs Frequency
THD<0.1%
10
10
8
R =500W
L
8
6
4
2
0
R =500W
L
R =150W
L
6
R =150W
L
4
2
A =2
V
A =2
V
0
1
10
100
1
10
100
Frequency (MHz)
Frequency (MHz)
Small Signal Step Response
Large Signal Step Response
V =±5V
S
V =±5V
S
R =150W
L
R =150W
L
A =2
V
A =2
V
200mV/div
1V/div
10ns/div
10ns/div
Settling Time vs Settling Accuracy
Transimpedance (RoI) vs Temperature
25
20
15
10
5
625
600
575
550
525
A =2
V
R =150W
L
V
STEP
=5V output
P-P
0
0.01
0.1
Settling Accuracy (%)
1
-40
10
60
110
160
Die Temperature (°C)
6
EL5397C - Preliminary
Triple 200MHz Fixed Gain Amplifier
Typical Performance Curves
Frequency Response (Gain)
Frequency Response (Phase)
SO8 Package
SO8 Package
6
90
A =-1
V
A =2
V
2
-2
0
-90
A =1
V
-6
-180
-270
-10
R =150W
L
R =150W
L
-14
-360
1M
10M
100M
1G
160
160
1M
10M
100M
Frequency (Hz)
1G
160
160
Frequency (Hz)
PSRR and CMRR vs Temperature
ICMR and IPSR vs Temperature
90
80
70
60
50
40
30
20
10
2
1.5
1
PSRR
ICMR+
IPSR
CMRR
0.5
0
ICMR-
-0.5
-40
-40
10
60
110
10
60
Die Temperature (°C)
110
Die Temperature (°C)
Offset Voltage vs Temperature
Input Current vs Temperature
2
1
60
40
20
IB-
0
0
-20
-40
-60
IB+
-1
-2
-40
10
60
110
-40
10
60
Die Temperature (°C)
110
Die Temperature (°C)
7
EL5397C - Preliminary
Triple 200MHz Fixed Gain Amplifier
Typical Performance Curves
Positive Input Resistance vs Temperature
Supply Current vs Temperature
60
5
4
3
2
1
0
50
40
30
20
10
0
-40
10
60
110
160
160
160
-40
10
60
110
160
Die Temperature (°C)
Die Temperature (°C)
Negative Output Swing vs Temperature for Various Loads
Positive Output Swing vs Temperature for Various Loads
-3.5
-3.6
-3.7
-3.8
-3.9
-4
4.2
4.1
4
150W
1kW
3.9
3.8
3.7
3.6
3.5
150W
1kW
-4.1
-4.2
-40
10
60
110
160
-40
10
60
110
Die Temperature (°C)
Die Temperature (°C)
Slew Rate vs Temperature
Output Current vs Temperature
4000
3500
3000
2500
130
125
120
115
Sink
Source
A =2
V
R =R =500W
F
G
R =150W
L
-40
10
60
110
160
-40
10
60
110
Die Temperature (°C)
Die Temperature (°C)
8
EL5397C - Preliminary
Triple 200MHz Fixed Gain Amplifier
Typical Performance Curves
Package Power Dissipation vs Ambient Temp.
JEDEC JESD51-3 Low Effective Thermal Conductivity Test Board
1
0.9
909mW
0.8
0.7
0.6
633mW
0.5
0.4
0.3
0.2
0.1
0
0
25
50
75
100
125
150
Ambient Temperature (°C)
9
EL5397C - Preliminary
Triple 200MHz Fixed Gain Amplifier
Pin Descriptions
EL5396C
16-Pin SO & 16-
Pin QSOP
Pin Name
Function
Equivalent Circuit
1
INA+
Non-inverting input, Channel A
R
G
IN+
IN-
R
F
Circuit1
2
CEA
Amplifier A enable
CE
Circuit 2
3
4
VS-
CEB
INB+
NC
Negative supply
Amplifier B enable
(Reference Circuit 2)
(Reference Circuit 1)
5
Non-inverting input, Channel B
Not connected
6
7
CEC
INC+
INC-
OUTC
Amplifier C enable
(Reference Circuit 2)
(Reference Circuit 1)
(Reference Circuit 1)
8
Non-inverting input, Channel C
Inverting input, Channel C
Output, Channel C
9
10
OUT
R
F
Circuit 3
11
12
13
14
15
16
NC
INB-
Not connected
Inverting input, Channel B
Output, Channel B
Positive supply
(Reference Circuit 1)
(Reference Circuit 3)
OUTB
VS+
OUTA
INA-
Output, Channel A
Inverting input, Channel A
(Reference Circuit 3)
(Reference Circuit 1)
10
EL5397C - Preliminary
Triple 200MHz Fixed Gain Amplifier
Applications Information
particularly for the SO package, should be avoided if
possible. Sockets add parasitic inductance and capaci-
tance which will result in additional peaking and
overshoot.
Product Description
The EL5397C is a current-feedback operational ampli-
fier that offers a wide -3dB bandwidth of 300MHz and a
low supply current of 4mA per amplifier. The EL5397C
works with supply voltages ranging from a single 5V to
10V and they are also capable of swinging to within 1V
of either supply on the output. Because of their current-
feedback topology, the EL5397C does not have the nor-
mal gain-bandwidth product associated with voltage-
feedback operational amplifiers. Instead, its -3dB band-
width to remain relatively constant as closed-loop gain is
increased. This combination of high bandwidth and low
power, together with aggressive pricing make the
EL5397C the ideal choice for many low-power/high-
bandwidth applications such as portable, handheld, or
battery-powered equipment.
Capacitance at the Inverting Input
Any manufacturer’s high-speed voltage- or current-
feedback amplifier can be affected by stray capacitance
at the inverting input. For inverting gains, this parasitic
capacitance has little effect because the inverting input is
a virtual ground, but for non-inverting gains, this capac-
itance (in conjunction with the feedback and gain
resistors) creates a pole in the feedback path of the
amplifier. This pole, if low enough in frequency, has the
same destabilizing effect as a zero in the forward open-
loop response. The use of large-value feedback and gain
resistors exacerbates the problem by further lowering
the pole frequency (increasing the possibility of
oscillation.)
For varying bandwidth needs, consider the EL5191C
with 1GHz on a 9mA supply current or the EL5192C
with 600MHz on a 6mA supply current. Versions
include single, dual, and triple amp packages with 5-pin
SOT23, 16-pin QSOP, and 8-pin or 16-pin SO outlines.
The EL5397C has been optimized with a 475W feedback
resistor. With the high bandwidth of these amplifiers,
these resistor values might cause stability problems
when combined with parasitic capacitance, thus ground
plane is not recommended around the inverting input pin
of the amplifier.
Power Supply Bypassing and Printed Circuit
Board Layout
As with any high frequency device, good printed circuit
board layout is necessary for optimum performance.
Low impedance ground plane construction is essential.
Surface mount components are recommended, but if
leaded components are used, lead lengths should be as
short as possible. The power supply pins must be well
bypassed to reduce the risk of oscillation. The combina-
tion of a 4.7µF tantalum capacitor in parallel with a
0.01µF capacitor has been shown to work well when
placed at each supply pin.
Feedback Resistor Values
The EL5397C has been designed and specified at a gain
of +2 with RF approximately 500W. This value of feed-
back resistor gives 200MHz of -3dB bandwidth at AV=2
with 2dB of peaking. With AV=-2, an RF of approxi-
mately 500W gives 175MHz of bandwidth with 0.2dB of
peaking. Since the EL5397C is a current-feedback
amplifier, it is also possible to change the value of RF to
get more bandwidth. As seen in the curve of Frequency
Response for Various RF and RG, bandwidth and peak-
ing can be easily modified by varying the value of the
feedback resistor.
For good AC performance, parasitic capacitance should
be kept to a minimum, especially at the inverting input.
(See the Capacitance at the Inverting Input section) Even
when ground plane construction is used, it should be
removed from the area near the inverting input to mini-
mize any stray capacitance at that node. Carbon or
Metal-Film resistors are acceptable with the Metal-Film
resistors giving slightly less peaking and bandwidth
because of additional series inductance. Use of sockets,
Because the EL5397C is a current-feedback amplifier,
its gain-bandwidth product is not a constant for different
closed-loop gains. This feature actually allows the
EL5397C to maintain about the same -3dB bandwidth.
As gain is increased, bandwidth decreases slightly while
11
EL5397C - Preliminary
Triple 200MHz Fixed Gain Amplifier
stability increases. Since the loop stability is improving
with higher closed-loop gains, it becomes possible to
reduce the value of RF below the specified 475W and
still retain stability, resulting in only a slight loss of
bandwidth with increased closed-loop gain.
EL5397C has dG and dP specifications of 0.03% and
0.04°.
Output Drive Capability
In spite of its low 4mA of supply current, the EL5397C
is capable of providing a minimum of ±120mA of output
current. With a minimum of ±120mA of output drive,
the EL5397C is capable of driving 50W loads to both
rails, making it an excellent choice for driving isolation
transformers in telecommunications applications.
Supply Voltage Range and Single-Supply
Operation
The EL5397C has been designed to operate with supply
voltages having a span of greater than 5V and less than
10V. In practical terms, this means that the EL5397C
will operate on dual supplies ranging from ±2.5V to
±5V. With single-supply, the EL5397C will operate
from 5V to 10V.
Driving Cables and Capacitive Loads
When used as a cable driver, double termination is
always recommended for reflection-free performance.
For those applications, the back-termination series resis-
tor will decouple the EL5397C from the cable and allow
extensive capacitive drive. However, other applications
may have high capacitive loads without a back-termina-
tion resistor. In these applications, a small series resistor
(usually between 5W and 50W) can be placed in series
with the output to eliminate most peaking. The gain
resistor (RG) can then be chosen to make up for any gain
loss which may be created by this additional resistor at
the output. In many cases it is also possible to simply
increase the value of the feedback resistor (RF) to reduce
the peaking.
As supply voltages continue to decrease, it becomes nec-
essary to provide input and output voltage ranges that
can get as close as possible to the supply voltages. The
EL5397C has an input range which extends to within 2V
of either supply. So, for example, on +5V supplies, the
EL5397C has an input range which spans ±3V. The out-
put range of the EL5397C is also quite large, extending
to within 1V of the supply rail. On a ±5V supply, the
output is therefore capable of swinging from -----4V to
+4V. Single-supply output range is larger because of the
increased negative swing due to the external pull-down
resistor to ground.
Current Limiting
Video Performance
The EL5397C has no internal current-limiting circuitry.
If the output is shorted, it is possible to exceed the Abso-
lute Maximum Rating for output current or power
dissipation, potentially resulting in the destruction of the
device.
For good video performance, an amplifier is required to
maintain the same output impedance and the same fre-
quency response as DC levels are changed at the output.
This is especially difficult when driving a standard video
load of 150W, because of the change in output current
with DC level. Previously, good differential gain could
only be achieved by running high idle currents through
the output transistors (to reduce variations in output
impedance.) These currents were typically comparable
to the entire 4mA supply current of each EL5397C
amplifier. Special circuitry has been incorporated in the
EL5397C to reduce the variation of output impedance
with current output. This results in dG and dP specifica-
tions of 0.03% and 0.04°, while driving 150W at a gain
of 2.
Power Dissipation
With the high output drive capability of the EL5397C, it
is possible to exceed the 150°C Absolute Maximum
junction temperature under certain very high load cur-
rent conditions. Generally speaking when RL falls below
about 25W, it is important to calculate the maximum
junction temperature (TJMAX) for the application to
determine if power supply voltages, load conditions, or
package type need to be modified for the EL5397C to
Video performance has also been measured with a 500W
load at a gain of +1. Under these conditions, the
12
EL5397C - Preliminary
Triple 200MHz Fixed Gain Amplifier
remain in the safe operating area. These parameters are
calculated as follows:
PDMAX for each amplifier can be calculated as follows:
V
OUTMAX
PD
= (2 ´ V ´ I
) + (V – V
) ´ ----------------------------
MAX
S
SMAX
S
OUTMAX
R
L
T
= T
+ (q ´ n ´ PD
)
MAX
JMAX
MAX
JA
where:
VS = Supply Voltage
where:
TMAX = Maximum Ambient Temperature
qJA = Thermal Resistance of the Package
n = Number of Amplifiers in the Package
ISMAX = Maximum Supply Current of 1A
VOUTMAX = Maximum Output Voltage (Required)
RL = Load Resistance
PDMAX = Maximum Power Dissipation of Each
Amplifier in the Package
13
EL5397C - Preliminary
Triple 200MHz Fixed Gain Amplifier
General Disclaimer
Specifications contained in this data sheet are in effect as of the publication date shown. Elantec, Inc. reserves the right to make changes in the cir-
cuitry or specifications contained herein at any time without notice. Elantec, Inc. assumes no responsibility for the use of any circuits described
herein and makes no representations that they are free from patent infringement.
WARNING - Life Support Policy
Elantec, Inc. products are not authorized for and should not be used
within Life Support Systems without the specific written consent of
Elantec, Inc. Life Support systems are equipment intended to sup-
port or sustain life and whose failure to perform when properly used
in accordance with instructions provided can be reasonably
Elantec Semiconductor, Inc.
675 Trade Zone Blvd.
Milpitas, CA 95035
Telephone: (408) 945-1323
(888) ELANTEC
expected to result in significant personal injury or death. Users con-
templating application of Elantec, Inc. Products in Life Support
Systems are requested to contact Elantec, Inc. factory headquarters
to establish suitable terms & conditions for these applications. Elan-
tec, Inc.’s warranty is limited to replacement of defective
components and does not cover injury to persons or property or
other consequential damages.
Fax:
(408) 945-9305
European Office: +44-118-977-6020
Japan Technical Center: +81-45-682-5820
Printed in U.S.A.
14
EL5397CS-T7 相关器件
| 型号 | 制造商 | 描述 | 价格 | 文档 |
| EL5397CU | ELANTEC | Triple 200MHz Fixed Gain Amplifier | 获取价格 |
|
| EL5397CU-T13 | ELANTEC | Triple 200MHz Fixed Gain Amplifier | 获取价格 |
|
| EL5397CU-T7 | ELANTEC | Video Amplifier, 3 Channel(s), 1 Func, PDSO16, QSOP-16 | 获取价格 |
|
| EL5410 | INTERSIL | 30MHz Rail-to-Rail Input-Output Op Amps | 获取价格 |
|
| EL5410CR | ELANTEC | 30MHz Rail-to-Rail Input-Output Op Amps | 获取价格 |
|
| EL5410CR | INTERSIL | 30MHz Rail-to-Rail Input-Output Op Amps | 获取价格 |
|
| EL5410CR-T13 | ELANTEC | 30MHz Rail-to-Rail Input-Output Op Amps | 获取价格 |
|
| EL5410CR-T13 | INTERSIL | 30MHz Rail-to-Rail Input-Output Op Amps | 获取价格 |
|
| EL5410CR-T7 | INTERSIL | 30MHz Rail-to-Rail Input-Output Op Amps | 获取价格 |
|
| EL5410CRZ | INTERSIL | 30MHz Rail-to-Rail Input-Output Op Amps | 获取价格 |
|
EL5397CS-T7 相关文章
Bourns 密封通孔金属陶瓷微调电位计产品选型手册(英文版)
- 2024-09-20
- 6
Bourns 精密环境传感器产品选型手册(英文版)
- 2024-09-20
- 9
Bourns POWrTher 负温度系数(NTC)热敏电阻手册 (英文版)
- 2024-09-20
- 8
Bourns GMOV 混合过压保护组件产品选型手册(英文版)
- 2024-09-20
- 6
