HM5425161B [ELPIDA]
256M SSTL_2 interface DDR SDRAM 143 MHz/133 MHz/125 MHz/100 MHz 4-Mword 】 16-bit 】 4-bank/8-Mword 】 8-bit 】 4-bank/ 16-Mword 】 4-bit 】 4-bank; 256M SSTL_2接口DDR SDRAM 143兆赫/ 133兆赫/ 125兆赫/ 100 MHz的4 Mword 】 16位】 4银行/ 8 - Mword 】 8位】 4银行/ 16 Mword 】 4位】 4-银行
| 型号： | HM5425161B |
| 厂家： | 
ELPIDA MEMORY |
| 描述： | 256M SSTL_2 interface DDR SDRAM 143 MHz/133 MHz/125 MHz/100 MHz 4-Mword 】 16-bit 】 4-bank/8-Mword 】 8-bit 】 4-bank/ 16-Mword 】 4-bit 】 4-bank |
| 文件： | 总65页 (文件大小：481K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
HM5425161B Series
HM5425801B Series
HM5425401B Series
256M SSTL_2 interface DDR SDRAM
143 MHz/133 MHz/125 MHz/100 MHz
4-Mword × 16-bit × 4-bank/8-Mword × 8-bit × 4-bank/
16-Mword × 4-bit × 4-bank
E0086H20 (Ver. 2.0)
Jan. 23, 2002
Description
The HM5425161B, the HM5425801B and the HM5425401B are the Double Data Rate (DDR) SDRAM
devices. Read and write operations are performed at the cross points of the CLK and the CLK. This high
speed data transfer is realized by the 2-bit prefetch piplined architecture. Data strobe (DQS) both for read and
write are available for high speed and reliable data bus design. By setting extended mode resistor, the on-chip
Delay Locked Loop (DLL) can be set enable or disable.
Features
•
•
•
•
•
•
•
2.5 V power supply
SSTL-2 interface for all inputs and outputs
Clock frequency: 143 MHz/133 MHz/125 MHz/100 MHz (max)
Data inputs, outputs, and DM are synchronized with DQS
4 banks can operate simultaneously and independently
Burst read/write operation
Programmable burst length: 2/4/8
Burst read stop capability
Elpida Memory, Inc. is a joint venture DRAM company of NEC Corporation and Hitachi, Ltd.
HM5425161B, HM5425801B, HM5425401B Series
•
Programmable burst sequence
Sequential
Interleave
•
Start addressing capability
Even and Odd
•
•
•
Programmable CAS latency: 2/2.5
8192 refresh cycles: 7.8 µs (64 ms/8192 cycles)
2 variations of refresh
Auto refresh
Self refresh
Ordering Information
Type No.
Frequency
CAS latency
Package
HM5425161BTT-75A*1
HM5425161BTT-75B*2
HM5425161BTT-10*3
133 MHz
133 MHz
100 MHz
2.0
2.5
2.0
400-mill 66-pin plastic
TSOP II
HM5425801BTT-75A*1
HM5425801BTT-75B*2
HM5425801BTT-10*3
133 MHz
133 MHz
100 MHz
2.0
2.5
2.0
HM5425401BTT-75A*1
HM5425401BTT-75B*2
HM5425401BTT-10*3
133 MHz
133 MHz
100 MHz
2.0
2.5
2.0
Notes: 1. 143 MHz operation at CAS latency = 2.5.
2. 100 MHz operation at CAS latency = 2.0.
3. 125 MHz operation at CAS latency = 2.5.
Data Sheet E0086H20
2
HM5425161B, HM5425801B, HM5425401B Series
Pin Arrangement (HM5425161B)
66-pin TSOP
VCC
DQ0
VCCQ
DQ1
DQ2
VSSQ
DQ3
DQ4
VCCQ
DQ5
DQ6
VSSQ
DQ7
NC
VCCQ
DQSL
NC
VCC
NC
DML
WE
CAS
RAS
CS
1
2
3
4
5
6
7
8
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
VSS
DQ15
VSSQ
DQ14
DQ13
VCCQ
DQ12
DQ11
VSSQ
DQ10
DQ9
VCCQ
DQ8
NC
VSSQ
DQSU
NC
VREF
VSS
DMU
CLK
CLK
CKE
NC
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
NC
A12
A11
A9
A8
A7
A6
A5
A4
BA0
BA1
A10(AP)
A0
A1
A2
A3
VCC
VSS
(Top view)
Data Sheet E0086H20
3
HM5425161B, HM5425801B, HM5425401B Series
Pin Description
Pin name
Function
A0 to A12
Address input
Row address A0 to A12
Column address
Bank select address
Data-input/output
A0 to A8
BA0, BA1
DQ0 to DQ15
DQSU
DQSL
CS
Upper input and output data strobe
Lower input and output data strobe
Chip select
RAS
Row address strobe command
Column address strobe command
Write enable
CAS
WE
DMU
DML
CLK
Upper byte input mask
Lower byte input mask
Clock input
CLK
Differential clock input
Clock enable
CKE
VREF
Input reference voltage
Power for internal circuit
Ground for internal circuit
Power for DQ circuit
VCC
VSS
VCCQ
VSSQ
Ground for DQ circuit
No connection
NC
Data Sheet E0086H20
4
HM5425161B, HM5425801B, HM5425401B Series
Pin Arrangement (HM5425801B)
66-pin TSOP
VCC
DQ0
VCCQ
NC
DQ1
VSSQ
NC
DQ2
VCCQ
NC
DQ3
VSSQ
NC
NC
VCCQ
NC
NC
VCC
NC
1
2
3
4
5
6
7
8
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
VSS
DQ7
VSSQ
NC
DQ6
VCCQ
NC
DQ5
VSSQ
NC
DQ4
VCCQ
NC
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
NC
VSSQ
DQS
NC
VREF
VSS
DM
CLK
CLK
CKE
NC
A12
A11
A9
A8
A7
A6
A5
A4
VSS
NC
WE
CAS
RAS
CS
NC
BA0
BA1
A10(AP)
A0
A1
A2
A3
VCC
(Top view)
Data Sheet E0086H20
5
HM5425161B, HM5425801B, HM5425401B Series
Pin Description
Pin name
Function
A0 to A12
Address input
Row address A0 to A12
Column address
Bank select address
Data-input/output
A0 to A9
BA0, BA1
DQ0 to DQ7
DQS
CS
Input and output data strobe
Chip select
RAS
CAS
WE
Row address strobe command
Column address strobe command
Write enable
DM
Input mask
CLK
Clock input
CLK
Differential clock input
Clock enable
CKE
VREF
Input reference voltage
Power for internal circuit
Ground for internal circuit
Power for DQ circuit
Ground for DQ circuit
No connection
VCC
VSS
VCCQ
VSSQ
NC
Data Sheet E0086H20
6
HM5425161B, HM5425801B, HM5425401B Series
Pin Arrangement (HM5425401B)
66-pin TSOP
VCC
NC
VCCQ
NC
DQ0
VSSQ
NC
NC
VCCQ
NC
DQ1
VSSQ
NC
NC
VCCQ
NC
NC
VCC
NC
NC
WE
CAS
RAS
CS
1
2
3
4
5
6
7
8
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
VSS
NC
VSSQ
NC
DQ3
VCCQ
NC
NC
VSSQ
NC
DQ2
VCCQ
NC
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
NC
VSSQ
DQS
NC
VREF
VSS
DM
CLK
CLK
CKE
NC
A12
A11
A9
A8
A7
A6
A5
A4
VSS
NC
BA0
BA1
A10(AP)
A0
A1
A2
A3
VCC
(Top view)
Data Sheet E0086H20
7
HM5425161B, HM5425801B, HM5425401B Series
Pin Description
Pin name
Function
A0 to A12
Address input
Row address A0 to A12
Column address
Bank select address
Data-input/output
Output data strobe
Chip select
A0 to A9, A11
BA0, BA1
DQ0 to DQ3
DQS
CS
RAS
CAS
WE
Row address strobe command
Column address strobe command
Write enable
DM
Input mask
CLK
Clock input
CLK
Differential clock input
Clock enable
CKE
VREF
Input reference voltage
Power for internal circuit
Ground for internal circuit
Power for DQ circuit
Ground for DQ circuit
No connection
VCC
VSS
VCCQ
VSSQ
NC
Data Sheet E0086H20
8
HM5425161B, HM5425801B, HM5425401B Series
Block Diagram
Address (A12, BA0, BA1)
Address register
AY0 to AY11
AX0 to AX12
Row address
buffer
BA0, BA1
Bank
select
Refresh
counter
Column address
buffer
A0 to A12,
BA0, BA1
Column address
counter
Mode register
CLK
Row
decoder
Row
decoder
Row
decoder
Row
decoder
CLK
CKE
CS
Bank 0
Bank 1
Bank 2
Bank 3
RAS
CAS
WE
1
*
1
*
1
*
1
*
DM,
DMU/DML
Input
DQS,
DQSU/DQSL
buffer
Output
buffer
DQS
buffer
DLL
2
DQ*
Notes: 1. 8192 row × 512 column × 16 bit: HM5425161B
8192 row × 1024 column × 8 bit: HM5425801B
8192 row × 2048 column × 4 bit: HM5425401B
2. DQ0 to DQ15: HM5425161B
DQ0 to DQ7: HM5425801B
DQ0 to DQ3: HM5425401B
Data Sheet E0086H20
9
HM5425161B, HM5425801B, HM5425401B Series
Pin Functions (1)
CLK, CLK (input pin): The CLK and the CLK are the master clock inputs. All inputs except DMs, DQSs
and DQs are referred to the cross point of the CLK rising edge and the VREF level. When a read operation,
DQSs and DQs are referred to the cross point of the CLK and the CLK. When a write operation, DMs and
DQs are referred to the cross point of the DQS and the VREF level. DQSs for write operation are referred to
the cross point of the CLK and the CLK.
CS (input pin): When CS is Low, commands and data can be input. When CS is High, all inputs are
ignored. However, internal operations (bank active, burst operations, etc.) are held.
RAS, CAS, and WE (input pins): These pins define operating commands (read, write, etc.) depending on
the combinations of their voltage levels. See "Command operation".
A0 to A12 (input pins): Row address (AX0 to AX12) is determined by the A0 to the A12 level at the cross
point of the CLK rising edge and the VREF level in a bank active command cycle. Column address (AY0 to
AY8; the HM5425161B, AY0 to AY9; the HM5425801B, AY0 to AY9, AY11; the HM5425401B) is loaded
via the A0 to the A9 at the cross point of the CLK rising edge and the VREF level in a read or a write command
cycle. This column address becomes the starting address of a burst operation.
A10 (AP) (input pin): A10 defines the precharge mode when a precharge command, a read command or a
write command is issued. If A10 = High when a precharge command is issued, all banks are precharged. If
A10 = Low when a precharge command is issued, only the bank that is selected by BA1/BA0 is precharged.
If A10 = High when read or write command, auto-precharge function is enabled. While A10 = Low, auto-
precharge function is disabled.
BA0/BA1 (input pin): BA0/BA1 are bank select signals. The memory array is divided into bank 0, bank 1,
bank 2 and bank 3. If BA1 = Low and BA0 = Low, bank 0 is selected. If BA1 = High and BA0 = Low, bank
1 is selected. If BA1 = Low and BA0 = High, bank 2 is selected. If BA1 = High and BA0 = High, bank 3 is
selected.
CKE (input pin): CKE controls power down and self-refresh. The power down and the self-refresh
commands are entered when the CKE is driven Low and exited when it resumes to High.
The CKE level must be kept for 1 CLK cycle (= tCKEPW) at least, that is, if CKE changes at the cross point of
the CLK rising edge and the VREF level with proper setup time tIS, by the next CLK rising edge CKE level
must be kept with proper hold time tIH.
Data Sheet E0086H20
10
HM5425161B, HM5425801B, HM5425401B Series
Pin Functions (2)
DM, DMU/DML (input pins): DM (the HM5425801B and the HM5425401B), DMU/DML (the
HM5425161B) are the reference signals of the data input mask function. DMs are sampled at the cross point
of DQS and VREF. DMU/DML provide the byte mask function. When DMU/DML = High, the data input at
the same timing are masked while the internal burst counter will be count up. DML controls the lower byte
(DQ0 to DQ7) and DMU controls the upper byte (DQ8 to DQ15) of write data.
DQ0 to DQ15 (input and output pins): Data are input to and output from these pins (the DQ0 to the DQ15;
the HM5425161B, the DQ0 to the DQ7; the HM5425801B, the DQ0 to the DQ3; the HM5425401B).
DQS, DQSU/DQSL (input and output pin):
DQS (the HM5425801B and the HM5425401B),
DQSU/DQSL (the HM5425161B) provide the read data strobes (as output) and the write data strobes (as
input). DQSL is the lower byte (DQ0 to DQ7) data strobe signal, DQSU is the upper byte (DQ8 to DQ15)
data strobe signal.
VCC and VCCQ (power supply pins): 2.5 V is applied. (VCC is for the internal circuit and VCCQ is for the
output buffer.)
VSS and VSSQ (power supply pins): Ground is connected. (VSS is for the internal circuit and VSSQ is for the
output buffer.)
Data Sheet E0086H20
11
HM5425161B, HM5425801B, HM5425401B Series
Command Operation
Command Truth Table
The HM5425161B, the HM5425801B and HM5425401B recognize the following commands specified by the
CS, RAS, CAS, WE and address pins. All other combinations than those in the table below are illegal.
CKE
Command
Symbol n – 1 n
CS RAS CAS WE BA1 BA0 AP Address
Ignore command
No operation
DESL
NOP
BST
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
L
H
L
L
L
L
L
L
L
L
L
L
L
L
L
×
×
H
H
L
×
×
×
×
V
V
V
V
V
V
×
×
×
L
L
×
×
×
V
V
V
V
V
V
×
×
×
L
×
×
×
L
H
L
H
V
L
H
×
×
L
L
×
×
×
V
V
V
V
V
×
×
×
×
V
V
H
H
H
H
H
H
L
H
L
Burst stop in read command
Column address and read command READ
Read with auto-precharge READA
Column address and write command WRIT
Write with auto-precharge WRITA
Row address strobe and bank active ACTV
H
H
L
L
L
L
L
H
H
H
L
H
L
Precharge select bank
Precharge all bank
Refresh
PRE
L
PALL
REF
L
L
L
H
H
L
SELF
MRS
EMRS
L
L
Mode register set
H
H
L
L
L
L
L
H
Notes: 1. H: VIH. L: VIL. ×: VIH or VIL. V: Valid address input
2. The CKE level must be kept for 1 CLK cycle (= tCKEPW) at least.
Ignore command [DESL]: When CS is High at the cross point of the CLK rising edge and the VREF level,
every input are neglected and internal status is held.
No operation [NOP]: As long as this command is input at the cross point of the CLK rising edge and the
VREF level, address and data input are neglected and internal status is held.
Burst stop in read operation [BST]: This command stops a burst read operation, which is not applicable for
a burst write operation.
Column address strobe and read command [READ]: This command starts a read operation. The start
address of the burst read is determined by the column address (AY0 to AY8; the HM5425161B, AY0 to AY9;
the HM5425801B, AY0 to AY9, AY11; the HM5425401B) and the bank select address (BA). After the
completion of the read operation, the output buffer becomes High-Z.
Data Sheet E0086H20
12
HM5425161B, HM5425801B, HM5425401B Series
Read with auto-precharge [READA]: This command starts a read operation. After completion of the read
operation, precharge is automatically executed.
Column address strobe and write command [WRIT]: This command starts a write operation. The start
address of the burst write is determined by the column address (AY0 to AY8; the HM5425161B, AY0 to
AY9; the HM5425801B, AY0 to AY9, AY11; the HM5425401B) and the bank select address (BA).
Write with auto-precharge [WRITA]: This command starts a write operation. After completion of the
write operation, precharge is automatically executed.
Row address strobe and bank activate [ACTV]: This command activates the bank selected by BA0/BA1
and determines a row address (AX0 to AX12). When BA1 = BA0 = Low, bank 0 is activated. When BA1 =
High and BA0 = Low, bank 1 is activated. When BA1 = Low and BA0 = High, bank 2 is activated. When
BA1 = BA0 = High, bank 3 is activated.
Precharge selected bank [PRE]: This command starts a pre-charge operation for the bank selected by
BA0/BA1.
Precharge all banks [PALL]: This command starts a precharge operation for all banks.
Refresh [REF/SELF]: This command starts a refresh operation. There are two types of refresh operation,
one is auto-refresh, and another is self-refresh. For details, refer to the CKE truth table section.
Mode register set/Extended mode register set [MRS/EMRS]: The DDR SDRAM has the two mode
registers, the mode register and the extended mode register, to defines how it works. The both mode registers
are set through the address pins (the A0 to the A12, BA0 to BA1) in the mode register set cycle. For details,
refer to "Mode register and extended mode register set".
Data Sheet E0086H20
13
HM5425161B, HM5425801B, HM5425401B Series
CKE Truth Table
CKE
Current state Command
n – 1
H
n
H
L
CS
L
RAS CAS WE Address Notes
Idle
Idle
Idle
Auto-refresh command (REF)
L
L
H
H
H
×
×
×
×
×
×
×
×
×
2
2
Self-refresh entry (SELF)
Power down entry (PDEN)
H
L
L
L
H
L
L
H
×
H
×
H
L
H
L
Self refresh
Power down
Self refresh exit (SELFX)
Power down exit (PDEX)
L
H
H
H
H
H
×
H
×
H
×
L
H
L
L
H
×
H
×
H
×
L
H
Notes: 1. H: VIH. L: VIL. ×: VIH or VIL.
2. All the banks must be in IDLE before executing this command.
3. The CKE level must be kept for 1 CLK cycle (= tCKEPW) at least.
Auto-refresh command [REF]: This command executes auto-refresh. The banks and the ROW addresses
to be refreshed are internally determined by the internal refresh contoroller. The average refresh cycle is 7.8
µs. The output buffer becomes High-Z after auto-refresh start. Precharge has been completed automatically
after the auto-refresh. The ACTV or MRS command can be issued tRFC after the last auto-refresh command.
Self-refresh entry [SELF]: This command starts self-refresh. The self-refresh operation continues as long
as CKE is held Low. During the self-refresh operation, all ROW addresses are repeated refreshing by the
internal refresh contoroller. A self-refresh is terminated by a self-refresh exit command.
Power down mode entry [PDEN]: tPDEN (= 1 cycle) after the cycle when [PDEN] is issued. The DDR
SDRAM enters into power-down mode. In power down mode, power consumption is suppressed by
deactivating the input initial circuit. Power down mode continues while CKE is held Low. No internal
refresh operation occurs during the power down mode. [PDEN] do not disable DLL.
Self-refresh exit [SELFX]: This command is executed to exit from self-refresh mode. 10 cycles (= tSNR
)
after [SELFX], non-read commands can be executed. For read operation, wait for 200 cycles (= tSRD) after
[SELFX] to adjust Dout timing by DLL. After the exit, within 7.8 µs input auto-refresh command.
Power down exit [PDEX]: The DDR SDRAM can exit from power down mode tPDEX (1 cycle min.) after the
cycle when [PDEX] is issued.
Data Sheet E0086H20
14
HM5425161B, HM5425801B, HM5425401B Series
Function Truth Table
The following tables show the operations that are performed when each command is issued in each state of
the DDR SDRAM.
Function Truth Table (1)
Current state
Precharging*2
CS RAS CAS WE Address
Command
DESL
Operation
NOP
Next state
ldle
ldle
—
H
L
L
L
L
L
L
L
H
L
L
L
L
L
L
L
×
×
×
×
×
×
H
H
H
H
L
H
H
L
H
L
NOP
NOP
ILLEGAL*12
BST
H
L
BA, CA, A10 READ/READA ILLEGAL*12
—
L
BA, CA, A10 WRIT/WRITA
ILLEGAL*12
ILLEGAL*12
NOP
—
H
H
L
H
L
BA, RA
ACTV
—
L
BA, A10
PRE, PALL
ldle
—
L
×
×
×
×
×
ILLEGAL
NOP
Idle*3
×
×
×
DESL
NOP
BST
ldle
ldle
—
H
H
H
H
L
H
H
L
H
L
NOP
ILLEGAL*12
H
L
BA, CA, A10 READ/READA ILLEGAL*12
—
L
BA, CA, A10 WRIT/WRITA
ILLEGAL*12
Activating
NOP
—
H
H
L
H
L
BA, RA
BA, A10
×
ACTV
Active
ldle
L
PRE, PALL
REF, SELF
L
H
Refresh/
ldle/
Selfrefresh
Selfrefresh*13
L
L
L
L
MODE
MRS
Mode register set*13 ldle
Refresh
H
×
×
×
×
DESL
NOP
ldle
(auto-refresh)*4
L
H
L
L
H
H
H
L
H
H
L
H
L
×
×
×
×
×
×
NOP
BST
NOP
ldle
—
ILLEGAL
ILLEGAL
ILLEGAL
—
×
—
Data Sheet E0086H20
15
HM5425161B, HM5425801B, HM5425401B Series
Function Truth Table (2)
Current state
Activating*5
CS RAS CAS WE Address
Command
DESL
Operation
NOP
Next state
Active
Active
—
H
L
L
L
L
L
L
L
H
L
L
L
×
×
×
×
×
×
H
H
H
H
L
H
H
L
H
L
NOP
NOP
ILLEGAL*12
BST
H
L
BA, CA, A10 READ/READA ILLEGAL*12
—
L
BA, CA, A10 WRIT/WRITA
ILLEGAL*12
ILLEGAL*12
ILLEGAL*12
ILLEGAL
NOP
—
H
H
L
H
L
BA, RA
ACTV
—
L
BA, A10
PRE, PALL
—
L
×
×
×
×
×
—
Active*6
×
×
×
DESL
NOP
BST
Active
Active
Active
H
H
H
H
H
L
H
L
NOP
ILLEGAL
H
BA, CA, A10 READ/READA Starting read
operation
Read/READ
A
L
H
L
L
BA, CA, A10 WRIT/WRITA
Starting write
operation
Write
recovering/
precharging
L
L
L
H
L
L
L
L
H
H
L
H
L
BA, RA
ACTV
ILLEGAL*12
Pre-charge
ILLEGAL
NOP
—
L
BA, A10
PRE, PALL
Idle
L
×
×
—
Read*7
×
×
×
×
DESL
Active
Active
Active
Active
H
H
H
H
H
L
H
L
×
NOP
NOP
×
BST
BST
BA, CA, A10
Interrupting burst
read operation to
start new read
ILLEGAL*14
H
READ/READA
BA, CA, A10
BA, RA
L
L
L
H
L
L
L
L
H
L
WRIT/WRITA
ACTV
—
ILLEGAL*12
H
H
—
Interrupting burst
read operation to
start pre-charge
BA, A10
PRE, PALL
Precharging
L
L
L
×
×
ILLEGAL
—
Data Sheet E0086H20
16
HM5425161B, HM5425801B, HM5425401B Series
Function Truth Table (3)
Current state
CS RAS CAS WE Address
Command
Operation
Next state
Read with auto- H
pre-charge*8
×
×
×
×
DESL
NOP
Precharging
L
L
L
L
L
L
L
H
H
H
H
L
H
H
L
H
L
×
×
NOP
BST
NOP
ILLEGAL*15
Precharging
—
—
—
—
—
—
H
L
BA, CA, A10 READ/READA ILLEGAL*15
L
BA, CA, A10 WRIT/WRITA
ILLEGAL*15
ILLEGAL*12, 15
ILLEGAL*12, 15
ILLEGAL
H
H
L
H
L
BA, RA
ACTV
L
BA, A10
PRE, PALL
L
×
×
×
Write*9
H
×
×
×
DESL
NOP
BST
NOP
Write
recovering
L
H
H
H
×
×
NOP
Write
recovering
L
L
H
H
H
L
L
ILLEGAL
—
H
BA, CA, A10 READ/READA Interrupting burst
write operation to
Read/ReadA
start read operation.
L
H
L
L
BA, CA, A10 WRIT/WRITA
Interrupting burst
write operation to
start new write
operation.
Write/WriteA
L
L
L
L
H
H
H
L
BA, RA
ACTV
ILLEGAL*12
—
BA, A10
PRE, PALL
Interrupting write
operation to start
pre-charge.
Idle
L
L
L
×
×
×
×
ILLEGAL
NOP
—
Write
H
×
×
DESL
Active
recovering*10
L
L
L
H
H
H
H
H
L
H
L
×
×
NOP
BST
NOP
Active
ILLEGAL
—
H
BA, CA, A10 READ/READA Starting read
operation.
Read/ReadA
L
H
L
L
BA, CA, A10 WRIT/WRITA
Starting new write
Write/WriteA
operation.
L
L
L
L
L
L
H
H
L
H
L
BA, RA
BA, A10
×
ACTV
ILLEGAL*12
ILLEGAL*12
—
—
—
PRE/PALL
×
ILLEGAL
Data Sheet E0086H20
17
HM5425161B, HM5425801B, HM5425401B Series
Function Truth Table (4)
Current state
CS RAS CAS WE Address
Command
Operation
Next state
Write with auto-
pre-charge*11
H
×
×
×
×
DESL
NOP
Precharging
L
L
L
L
L
L
L
H
H
H
H
L
H
H
L
H
L
×
×
NOP
BST
NOP
Precharging
ILLEGAL
—
—
—
—
—
—
H
L
BA, CA, A10 READ/READA ILLEGAL*15
L
BA, CA, A10 WRIT/WRIT A
ILLEGAL*15
ILLEGAL*12, 15
ILLEGAL*12, 15
ILLEGAL
H
H
L
H
L
BA, RA
BA, A10
×
ACTV
L
PRE, PALL
L
×
Notes: 1. H: VIH. L: VIL. ×: VIH or VIL.
2. The DDR SDRAM is in "Precharging" state for tRP after precharge command is issued.
3. The DDR SDRAM reachs "IDLE" state tRP after precharge command is issued.
4. The DDR SDRAM is in "Refresh" state for tRC after auto-refresh command is issued.
5. The DDR SDRAM is in "Activating" state for tRCD after ACTV command is issued.
6. The DDR SDRAM is in "Active" state after "Activating" is completed.
7. The DDR SDRAM is in "READ" state until burst data have been output and DQ output circuits are
turned off.
8. The DDR SDRAM is in "READ with auto-precharge" from READA command until burst data has
been output and DQ output circuits are turned off.
9. The DDR SDRAM is in "WRITE" state from WRIT command to the last burst data are input.
10. The DDR SDRAM is in "Write recovering" for tWR after the last data are input.
11. The DDR SDRAM is in "Write with auto-precharge" until tWR after the last data has been input.
12. This command may be issued for other banks, depending on the state of the banks.
13. All banks must be in "IDLE".
14. Before executing a write command to stop the preceding burst read operation, BST command must
be issued.
15. See ‘Read with Auto-Precharge Enabled, Write with Auto-Precharge Enable’ section.
Data Sheet E0086H20
18
HM5425161B, HM5425801B, HM5425401B Series
Read with Auto-Precharge Enabled, Write with Auto-Precharge Enabled
The Elpida HM5425401/801/161B series support the concurrent auto precharge feature, a read with auto-
precharge enabled, or a write with auto-precharge enabled, may be followed by any command to the other
banks, as long as that command does not interrupt the read or write data transfer, and all other related
limitations apply (e.g. contention between READ data and WRITE data must be avoided.)
The minimum delay from a read or write command with auto precharge enabled, to a command to a
different bank, is summarized below.
To command (different bank, non- Minimum delay
From command
interrupting command)
Read or Read w/AP
Write or Write w/AP
Precharge or Activate
Read or Read w/AP
Write or Write w/AP
Precharge or Activate
(Concurrent AP supported)
Units
tCK
tCK
tCK
tCK
tCK
tCK
Read w/AP
BL/2
CL(rounded up)+ (BL/2)
1
Write w/AP
1 + (BL/2) + tWTR
BL/2
1
Data Sheet E0086H20
19
HM5425161B, HM5425801B, HM5425401B Series
Simplified State Diagram
SELF
REFRESH
SR ENTRY
SR EXIT
*1
MRS
REFRESH
CKEH
MODE
REGISTER
SET
AUTO
REFRESH
IDLE
CKEL
IDLE
POWER
DOWN
ACTIVE
ACTIVE
POWER
DOWN
CKEL
CKEH
ROW
ACTIVE
BST
READ
WRITE
Write
WRITE
WITH
AP
READ
WITH
AP
Read
WRITE
READ
READ
READ
WITH AP
WRITE
WITH AP
READ
WITH AP
PRECHARGE
WRITEA
READA
PRECHARGE PRECHARGE
POWER
APPLIED
POWER
ON
PRECHARGE
PRECHARGE
Automatic transition after completion of command.
Transition resulting from command input.
Note: 1. After the auto-refresh operation, precharge operation is performed automatically
and enter the IDLE state.
Data Sheet E0086H20
20
HM5425161B, HM5425801B, HM5425401B Series
Operation of the DDR SDRAM
Power-up Sequence
The following sequence is recommended for Power-up.
(1) Apply power and attempt to maintain CKE at an LVCMOS low state (all other inputs may be undefined).
Apply VCC before or at the same time as VCCQ
.
Apply VCCQ before or at the same time as VTT and VREF
.
(2) Start clock and maintain stable condition for a minimum of 200 µs.
(3) After the minimum 200 µs of stable power and clock (CLK, CLK), apply NOP and take CKE high.
(4) Issue precharge all command for the device.
(5) Issue EMRS to enable DLL.
(6) Issue a mode register set command (MRS) for "DLL reset" with bit A8 set to high (An additional 200
cycles of clock input is required to lock the DLL after every DLL reset).
(7) Issue precharge all command for the device.*1
(8) Issue 2 or more auto-refresh commands.*1
(9) Issue a mode register set command to initialize device operation with bit A8 set to low in order to avoid
resetting the DLL.
Note: 1. Sequence of (7) and (8) may be reversed.
Power-up Sequence after CKE Goes High
(4)
(5)
(6)
(7)
(8)
(9)
Any
command
Command
PALL
EMRS
MRS
PALL
REF
REF
MRS
t
t
t
RC
2 cycles (min)
2 cycles (min)
2 cycles (min)
2 cycles (min)
RP
RC
DLL enable
DLL reset
with A8 = High
Disable DLL reset
with A8 = Low
200 cycles (min)
Data Sheet E0086H20
21
HM5425161B, HM5425801B, HM5425401B Series
Mode Register and Extended Mode Register Set
There are two mode registers, the mode register and the extended mode register so as to define the operating
mode. Parameters are set to both through the A0 to the A12 and BA0, BA1 pins by the mode register set
command [MRS] or the extended mode register set command [EMRS]. The mode register and the extended
mode register are set by inputting signal via the A0 to the A12 and BA0, BA1 during mode register set cycles.
BA0 and BA1 determine which one of the mode register or the extended mode register are set. Prior to a read
or a write operation, the mode register must be set.
Remind that no other parameters are shown in the table bellow are allowed to input to the registers.
Mode Register Set [MRS] (BA0 = 0, BA1 = 0)
BA0 BA1 A12 A11 A10 A9 A8 A7 A6 A5 A4
DR LMODE
A3
BT
A2 A1
BL
A0
0
0
0
0
0
0
0
MRS
A6 A5 A4 CAS Latency
A8 DLL Reset
A3 Burst Type
Burst Length
BT=0 BT=1
A2 A1 A0
2
0
1
1
1
0
0
0
1
No
0
1
Sequential
Interleave
2.5
2
4
8
2
4
8
0
0
0
0
1
1
1
0
1
Yes
Extended Mode Register Set [EMRS] (BA0 = 1, BA1 = 0)
BA0 BA1 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0
DLL
1
0
0
0
0
0
0
0
0
0
0
0
0
0
EMRS
A0 DLL Control
0
1
DLL Enable
DLL Disable
Data Sheet E0086H20
22
HM5425161B, HM5425801B, HM5425401B Series
Burst Operation
The burst type (BT) and the first three bits of the column address determines the order of a data out.
Burst length = 2
Burst length = 4
Starting Ad. Addressing(decimal)
Starting Ad. Addressing(decimal)
A0
0
Sequence Interleave
A1
0
A0 Sequence
Interleave
0, 1,
1, 0,
0, 1,
1, 0,
0
1
0
1
0, 1, 2, 3,
0, 1, 2, 3,
1, 0, 3, 2,
2, 3, 0, 1,
3, 2, 1, 0,
1
0
1, 2, 3, 0,
2, 3, 0, 1,
1
1
3,
0, 1, 2,
Burst length = 8
Starting Ad.
Addressing(decimal)
A2 A1 A0 Sequence
Interleave
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0, 1, 2, 3, 4, 5, 6, 7,
1, 2, 3, 4, 5, 6, 7, 0,
2, 3, 4, 5, 6, 7, 0, 1,
3, 4, 5, 6, 7, 0, 1, 2,
4, 5, 6, 7, 0, 1, 2, 3,
5, 6, 7, 0, 1, 2, 3, 4,
6, 7, 0, 1, 2, 3, 4, 5,
7, 0, 1, 2, 3, 4, 5, 6,
0, 1, 2, 3, 4, 5, 6, 7,
1, 0, 3, 2, 5, 4, 7, 6,
2, 3, 0, 1, 6, 7, 4, 5,
3, 2, 1, 0, 7, 6, 5, 4,
4, 5, 6, 7, 0, 1, 2, 3,
5, 4, 7, 6, 1, 0, 3, 2,
6, 7, 4, 5, 2, 3, 0, 1,
7, 6, 5, 4, 3, 2, 1, 0,
Data Sheet E0086H20
23
HM5425161B, HM5425801B, HM5425401B Series
Read/Write Operations
Bank active: A read or a write operation begins with the bank active command [ACTV]. The bank active
command determines a bank address (BA0, BA1) and a row address (AX0 to AX12). For the bank and the
row, a read or a write command can be issued tRCD after the ACTV is issued.
Read operation: The burst length (BL), the CAS latency (CL) and the burst type (BT) of the mode register
are referred when a read command is issued. The burst length (BL) determines the length of a sequential
output data by the read command which can be set to 2, 4, or 8. The starting address of the burst read is
defined by the column address (AY0 to AY8; the HM5425161B, AY0 to AY9; the HM5425801B, AY0 to
AY9, AY11; the HM5425401B), the bank select address (BA0, BA1) which are loaded via the A0 to A12 and
BA0, BA1 pins in the cycle when the read command is issued. The data output timing are characterized by
CL (2 or 2.5) and tAC. The read burst start CL • tCK + t (ns) after the clock rising edge where the read
AC
command are latched. The DDR SDRAM output the data strobe through DQS or DQSU/DQSL
simultaneously with data. tRPRE prior to the first rising edge of the data strobe, the DQS or the DQSU/DQSL
are driven Low from VTT level. This low period of DQS is referred as read preamble. The burst data are
output coincidentally at both the rising and falling edge of the data strobe. The DQ pins become High-Z in
the next cycle after the burst read operation completed. tRPST from the last falling edge of the data strobe, the
DQS pins become High-Z. This low period of DQS is referred as read postamble.
Read Operation (Burst Length)
t0
t1
t2
t3
t4
t5
t6
t7
t8
CLK
CLK
tRCD
NOP
Command
Address
NOP
ACTV
Row
READ
NOP
Column
tRPRE
D0 D1
BL = 2
tRPST
DQS*
Dout
D0 D1 D2 D3
BL = 4
BL = 8
D0 D1 D2 D3 D4 D5 D6 D7
CAS latency = 2
BL: Burst length
DQS*:DQS,DUSU/DQSL
Data Sheet E0086H20
24
HM5425161B, HM5425801B, HM5425401B Series
Read Operation (CAS Latency)
t0 t0.5 t1 t1.5 t2 t2.5 t3 t3.5 t4 t4.5 t5
t5.5
CLK
CLK
Read
NOP
Command
tRPRE
tRPST
V
DQS
TT
CL = 2
tAC,tDQSCK
V
V
D0 D1 D2 D3
TT
DQ
tRPRE
tRPST
DQS
TT
CL = 2.5
tAC,tDQSCK
V
TT
D0 D1 D2 D3
DQ
Data Sheet E0086H20
25
HM5425161B, HM5425801B, HM5425401B Series
Write operation: The burst length (BL) and the burst type (BT) of the mode register are referred when a
write command is issued. The burst length (BL) determines the length of a sequential data input by the write
command which can be set to 2, 4, or 8. The latency from write command to data input is fixed to 1. The
starting address of the burst read is defined by the column address (AY0 to AY8; the HM5425161B, AY0 to
AY9; the HM5425801B, AY0 to AY9, AY11; the HM5425401B), the bank select address (BA0/BA1) which
are loaded via the A0 to A12, BA0 to BA1 pins in the cycle when the write command is issued. DQS,
DQSU/DQSL should be input as the strobe for the input-data and DM, DMU/DML as well during burst
operation. tWPREH prior to the first rising edge of the DQS, the DQSU/DQSL should be set to Low and tWPST
after the last falling edge of the data strobe can be set to High-Z. The leading low period of DQS is referred
as write preamble. The last low period of DQS is referred as wrtie postamble.
Write Operation
t0
t1
t2
t3 t3.5 t4
t5
t6
t7
t8
CLK
CLK
tRCD
NOP
Command
Address
NOP
ACTV
Row
WRITE
NOP
Column
tWPREH
tWPRES
in0 in1
BL = 2
tWPST
DQS*
Din
in0 in1 in2 in3
BL = 4
BL = 8
in0 in1 in2 in3 in4 in5 in6 in7
BL: Burst length
DQS*:DQS,DQSU/DQSL
Data Sheet E0086H20
26
HM5425161B, HM5425801B, HM5425401B Series
Burst Stop
Burst stop command during burst read: The burst stop (BST) command is used to stop data output during
a burst read. The BST command stops the burst read and sets the output buffer to High-Z. tBSTZ (= CL) cycles
after a BST command issued, the DQ pins become High-Z. The BST command is not supported for the burst
write operation. Note that bank address is not referred when this command is executed.
Burst Stop during a Read Operation
t0 t0.5 t1 t1.5 t2 t2.5 t3 t3.5 t4 t4.5 t5
t5.5
CLK
CLK
Read
Command
BST
NOP
tBSTZ
2 cycles
DQS
CL = 2
D0 D1
tBSTZ
DQ
2.5 cycles
DQS
DQ
CL = 2.5
D0 D1
CL: CAS latency
Data Sheet E0086H20
27
HM5425161B, HM5425801B, HM5425401B Series
Auto Precharge
Read with auto-precharge: The precharge is automatically performed after completing a read operation.
The precharge starts tRPD (BL/2) cycle after READA command input. tRAP specification for READA allows a
read command with auto precharge to be issued to a bank that has been activated (opened) but has not yet
satisfied the tRAS(min) specification. A column command to the other active bank can be issued at the next
cycle after the last data output. Read with auto-precharge command does not limit row commands execution
for other bank. Refer to the ‘Read with Auto-Precharge Enabled, Write with Auto-Precharge Enabled’
section.
CLK
CLK
tRP (min)
t
t
(min) = t
(min)
RCD
RPD
RAP
2 cycles (= BL/2)
ACTV
READA
NOP
ACTV
Command
DQS,
DQSU/DQSL
tAC,tDQSCK
DQ
D0 D1 D2 D3
Note: Internal auto-precharge starts at the timing indicated by " ".
Data Sheet E0086H20
28
HM5425161B, HM5425801B, HM5425401B Series
Write with auto-precharge: The precharge is automatically performed after completing a burst write
operation. The precharge operation is started tWPD (= BL/ 2 + 3) cycles after WRITA command issued. tRCD
for WRITA should be determined so that tRC (ACTV to ACTV) spec. is obeyed when WRITA is issued
successively after a bank active command, that is tRCD (WRITA) ≥ tRC(min.)-t (min.)-tWPD. A column
RP
command to the other banks can be issued the next cycle after the internal precharge command issued. Write
with auto-precharge command does not limit row commands execution for other bank. Refer to the ‘Read
with Auto-Precharge Enabled, Write with Auto-Precharge Enabled’ section
Burst Write (Burst Length = 4)
CLK
CLK
tRAS (min)
tRP
tRCD (min)
ACTV
NOP
WRITA
NOP
tWPD
ACTV
Command
BL/2 + 3 cycles
DM,
DMU/DML
DQS,
DQSU/DQSL
DQ
D1 D2 D3 D4
Burst length = 4
Note: Internal auto-precharge starts at the timing indicated by " ".
Data Sheet E0086H20
29
HM5425161B, HM5425801B, HM5425401B Series
Command Intervals
A Read command to the consecutive Read command Interval
Destination row of the
consecutive read command
Bank
Row
address address
State
Operation
1. Same
Same
ACTIVE
The consecutive read can be performed after an interval of no less
than 1 cycle to interrupt the preceding read operation.
2. Same
Different
—
Precharge the bank to interrupt the preceding read operation. tRP after
the precharge command, issue the ACTV command. tRCD after the
ACTV command, the consecutive read command can be issued. See
‘A read command to the consecutive precharge interval’ section.
3. Different
Any
ACTIVE
IDLE
The consecutive read can be performed after an interval of no less
than 1 cycle to interrupt the preceding read operation.
Precharge the bank without interrupting the preceding read operation.
t
RP after the precharge command, issue the ACTV command. tRCD after
the ACTV command, the consecutive read command can be issued.
READ to READ Command Interval (same ROW address in the same bank)
t0
t1
t2
t3
t4
t5
t6
t7
t8
CLK
CLK
Command
NOP
ACTV
Row
NOP
READ
READ
Column A Column B
Address
BA
Dout
A0 A1 B0
B1 B2 B3
Column = A Column = B
Read
Read
Column = A
Dout
Column = B
Dout
DQS,
DQSU/DQSL
CAS latency = 2
Burst length = 4
Bank0
Bank0
Active
Data Sheet E0086H20
30
HM5425161B, HM5425801B, HM5425401B Series
READ to READ Command Interval (different bank)
t0
t1
t2
t3
t4
t5
t6
t7
t8
t9
CLK
CLK
Command
READ
READ
NOP
ACTV
Row0
NOP
ACTV
Row1
NOP
Column A Column B
Address
BA
Dout
A0 A1 B0 B1 B2 B3
Column = A Column = B
Read
Read
Bank0
Dout
Bank3
Dout
DQS,
DQSU/DQSL
CAS latency = 2
Burst length = 4
Bank0
Active
Bank3
Active
Bank0
Read
Bank3
Read
Data Sheet E0086H20
31
HM5425161B, HM5425801B, HM5425401B Series
A Write command to the consecutive Write command Interval:
Destination row of the
consecutive write command
Bank
Row
address address
State
Operation
1. Same
Same
ACTIVE
The consecutive write can be performed after an interval of no less
than 1 cycle to interrupt the preceding write operation.
2. Same
Different
—
Precharge the bank to interrupt the preceding write operation. tRP after
the precharge command, issue the ACTV command. tRCD after the
ACTV command, the consecutive write command can be issued. See
‘A write command to the consecutive precharge interval’ section.
3. Different
Any
ACTIVE
IDLE
The consecutive write can be performed after an interval of no less
than 1 cycle to interrupt the preceding write operation.
Precharge the bank without interrupting the preceding write operation.
t
RP after the precharge command, issue the ACTV command. tRCD after
the ACTV command, the consecutive write command can be issued.
WRITE to WRITE Command Interval (same ROW address in the same bank)
t0
t1
t2
t3
t4
t5
t6
t7
t8
CLK
CLK
Command
NOP
ACTV
Row
NOP
WRIT
WRIT
Column A Column B
Address
BA
Din
A0 A1
B0 B1 B2 B3
Column = A
Write
Column = B
Write
DQS,
DQSU/DQSL
Bank0
Active
Burst length = 4
Bank0
Data Sheet E0086H20
32
HM5425161B, HM5425801B, HM5425401B Series
WRITE to WRITE Command Interval (different bank)
t0
t1
t2
t3
t4
t5
t6
t7
t8
t9
CLK
CLK
Command
WRIT
WRIT
NOP
ACTV
Row0
NOP
ACTV
Row1
Column A Column B
Address
BA
Din
A0 A1 B0 B1 B2 B3
Bank0
Write
Bank3
Write
DQS,
DQSU/DQSL
Burst length = 4
Bank0, 3
Bank0
Active
Bank3
Active
Data Sheet E0086H20
33
HM5425161B, HM5425801B, HM5425401B Series
A Read command to the consecutive Write command interval with the BST command
Destination row of the
consecutive write command
Bank
Row
address address
State
Operation
1. Same
Same
ACTIVE
Issue the BST command. tBSTW (≥ tBSTZ) after the BST command, the
consecutive write command can be issued.
2. Same
Different
—
Precharge the bank to interrupt the preceding read operation. tRP after
the precharge command, issue the ACTV command. tRCD after the
ACTV command, the consecutive write command can be issued. See
‘A read command to the consecutive precharge interval’ section.
3. Different
Any
ACTIVE
IDLE
Issue the BST command. tBSTW (≥ tBSTZ) after the BST command, the
consecutive write command can be issued.
Precharge the bank independently of the preceding read operation.
t
RP after the precharge command, issue the ACTV command. tRCD after
the ACTV command, the consecutive write command can be issued.
READ to WRITE Command Interval
t0
t1
t2
t3
t4
t5
t6
t7
t8
CLK
CLK
Command
READ
WRIT
BST
NOP
NOP
t
(≥ t
)
BSTZ
BSTW
DM,
DMU/DML
t
(= CL)
BSTZ
DQ
Q0 Q1
D0 D1 D2 D3
High-Z
DQS,
DQSU/DQSL
OUTPUT
INPUT
Burst Length = 4
CAS Latency= 2
Data Sheet E0086H20
34
HM5425161B, HM5425801B, HM5425401B Series
A Write command to the consecutive Read command interval: To complete the burst operation
Destination row of the
consecutive read command
Bank
Row
address address
State
Operation
1. Same
Same
ACTIVE
To complete the burst operation, the consecutive read command
should be performed tWRD (= BL/ 2 + 2) after the write command.
2. Same
Different
—
Precharge the bank tWPD after the preceding write command. tRP after
the precharge command, issue the ACTV command. tRCD after the
ACTV command, the consecutive read command can be issued. See
‘A read command to the consecutive precharge interval’ section.
3. Different
Any
ACTIVE
IDLE
To complete a burst operation, the consecutive read command should
be performed tWRD (= BL/ 2 + 2) after the write command.
Precharge the bank independently of the preceding write operation.
t
RP after the precharge command, issue the ACTV command. tRCD after
the ACTV command, the consecutive read command can be issued.
WRITE to READ Command Interval
t0
t1
t2
t3
t4
t5
t6
CLK
CLK
Command
WRIT
NOP
READ
NOP
tWRD (min)
BL/2 + 2 cycle
DM,
DMU/DML
DQ
Q2
D0 D1 D2 D3
Q0 Q1
DQS,
DQSU/DQSL
INPUT
OUTPUT
BL = 4
CL = 2
Data Sheet E0086H20
35
HM5425161B, HM5425801B, HM5425401B Series
A Write command to the consecutive Read command interval: To interrupt the write operation
Destination row of the
consecutive read command
Bank
Row
address address
State
Operation
1. Same
Same
ACTIVE
DM, DMU/DML must be input 1 cycle prior to the read command input
to prevent from being written invalid data. In case, the read command
is input in the next cycle of the write command, DM, DMU/DML is not
necessary.
2. Same
Different
Any
—
—*1
3. Different
ACTIVE
DM, DMU/DML must be input 1 cycle prior to the read command input
to prevent from being written invalid data. In case, the read command
is input in the next cycle of the write command, DM, DMU/DML is not
necessary.
IDLE
—*1
Note: 1. Precharge must be preceded to read command. Therefore read command can not interrupt the
write operation in this case.
WRITE to READ Command Interval (Samebank, same ROW address)
[WRITE to READ delay = 1 clock cycle]
t0
t1
t2
t3
t4
t5
t6
t7
t8
CLK
CLK
Command
WRIT
READ
NOP
1 cycle
CL=2
DM,
DMU/DML
High-Z
High-Z
DQ
D0 D1
Q0 Q1 Q2 Q3
D2
DQS,
DQSU/DQSL
BL = 4
CL= 2
Data masked
Data Sheet E0086H20
36
HM5425161B, HM5425801B, HM5425401B Series
[WRITE to READ delay = 2 clock cycle]
t0
t1
t2
t3
t4
t5
t6
t7
t8
CLK
CLK
Command
WRIT
NOP
READ
NOP
2 cycle
CL=2
DM,
DMU/DML
High-Z
High-Z
DQ
D0 D1
Q0 Q1 Q2 Q3
D2 D3
DQS,
DQSU/DQSL
Data masked
BL = 4
CL= 2
[WRITE to READ delay = 3 clock cycle]
t0
t1
t2
t3
t4
t5
t6
t7
t8
CLK
CLK
Command
WRIT
NOP
3 cycle
READ
NOP
CL=2
DM,
DMU/DML
DQ
D0 D1
Q0 Q1 Q2 Q3
D2 D3
DQS,
DQSU/DQSL
BL = 4
CL= 2
Data masked
Data Sheet E0086H20
37
HM5425161B, HM5425801B, HM5425401B Series
A Read command to the consecutive Precharge command interval (same bank):
To output all data: To complete a burst read opeartion and get a burst length of data, the consecutive
precharge command must be issued tRPD (= BL/ 2 cycles) after the read command is issued.
READ to PRECHARGE Command Interval (same bank): To output all data
CAS Latency = 2, Burst Length = 4
t0
t1
t2
t3
t4
t5
t6
t7
t8
CLK
CLK
Command
Dout
PRE/
PALL
NOP
NOP
NOP
READ
A0 A1 A2 A3
DQS,
DQSU/DQSL
tRPD = BL/2
CAS Latency = 2.5, Burst Length = 4
t0
t1
t2
t3
t4
t5
t6
t7
t8
CLK
CLK
Command
Dout
PRE/
PALL
NOP
NOP
NOP
READ
A0 A1
A2 A3
DQS,
DQSU/DQSL
tRPD = BL/2
Data Sheet E0086H20
38
HM5425161B, HM5425801B, HM5425401B Series
READ to PRECHARGE Command Interval (same bank): To stop output data
A burst data output can be interrupted with a precharge command. All DQ pins and DQS pins become High-
Z tHZP (= CL) after the precharge command.
CAS Latency = 2, Burst Length = 2, 4, 8
t0
t1
t2
t3
t4
t5
t6
t7
t8
CLK
CLK
Command
Dout
NOP
NOP
PRE/PALL
READ
High-Z
High-Z
A0 A1
DQS,
DQSU/DQSL
tHZP = CL + 1
CAS Latency = 2.5, Burst Length = 2, 4, 8
t0
t1
t2
t3
t4
t5
t6
t7
t8
CLK
CLK
Command
Dout
PRE/PALL
CL = 2.5
NOP
NOP
READ
High-Z
A0 A1
DQS,
DQSU/DQSL
High-Z
tHZP = CL + 1
Data Sheet E0086H20
39
HM5425161B, HM5425801B, HM5425401B Series
A Write command to the consecutive Precharge command interval (same bank): The minimum interval
tWPD ((BL/ 2 + 3) cycles) is necessary between the write command and the precharge command.
WRITE to PRECHARGE Command Interval (same bank)
Burst Length = 4
t0
t1
t2
t3
t4
t5
t6
t7
CLK
CLK
Command
PRE/PALL
WRIT
NOP
tWPD
BL/2 +3 cycles
NOP
tWR
DM,
DMU/DML
DQS,
DQSU/DQSL
Din
A0 A1 A2 A3
Last data input
Data Sheet E0086H20
40
HM5425161B, HM5425801B, HM5425401B Series
Bank active command interval:
Destination row of the
consecutive ACTV command
Bank
Row
address address
State
Operation
1. Same
Any
Any
ACTIVE
Two successive ACTV commands can be issued at tRC interval. In
between two successive ACTV operations, precharge command
should be executed.
2. Different
ACTIVE
IDLE
Prechage the bank. tRP after the precharge command, the consecutive
ACTV command can be issued.
tRRD after an ACTV command, the next ACTV command can be issued.
Bank Active to Bank Active
CLK
CLK
Command
ACTV
ACTV
NOP
PRE
NOP
ACTV
NOP
Address
BA
ROW: 0
ROW: 1
ROW: 0
Bank0
Active
Bank3
Active
Bank0
Precharge
Bank0
Active
tRRD
tRC
Mode register set to Bank-active command interval: The interval between setting the mode register and
executing a bank-active command must be no less than tMRD
.
CLK
CLK
Command
Address
MRS
NOP
ACTV
NOP
CODE
BS and ROW
Mode Register Set
Bank3
Active
tMRD
Data Sheet E0086H20
41
HM5425161B, HM5425801B, HM5425401B Series
DMU/DML Control (HM5425161B)
DMU can mask upper byte of input data. DML can mask lower byte of input data. By setting DMU/DML to
Low, data can be written. When DMU/DML is set to High, the corresponding data is not written, and the
previous data is held. The latency between DMU/DML input and enabling/disabling mask function is 0.
DM Control (HM5425801B/HM5425401B)
DM can mask input data. By setting DM to Low, data can be written. When DM is set to High, the
corresponding data is not written, and the previous data is held. The latency between DM input and
enabling/disabling mask function is 0.
t1
t2
t3
t4
t5
t6
DQS,
DQSU/DQSL
DQ
Mask
Mask
DM,
DMU/DML
Write mask latency = 0
Data Sheet E0086H20
42
HM5425161B, HM5425801B, HM5425401B Series
Absolute Maximum Ratings
Parameter
Symbol
VCC, VCCQ
Vti
Value
Unit
V
Note
Supply voltage relative to VSS
Voltage on inputs pin relative to Vss
Voltage on I/O pins relative to VSS
Short circuit output current
Power dissipation
–1.0 to +3.6
–1.0 to +3.6
–0.5 to +3.6
50
V
VTio
Iout
V
mA
W
PT
1.0
Operating temperature
Storage temperature
Topr
Tstg
0 to +70
–55 to +125
°C
°C
DC Operating Conditions (Ta = 0 to +70˚C)
Parameter
Symbol
VCC, VCCQ
VSS, VSSQ
VREF(DC)
VTT
Min
2.3
0
Typ
2.5
0
Max
2.7
0
Unit
Notes
Supply voltage
V
V
V
V
V
V
V
1, 2
Input reference voltage
Termination voltage
DC Input high voltage
DC Input low voltage
0.5×VCCQ–0.05 0.5×VCCQ
0.5×VCCQ+0.05
VREF+0.04
VCCQ+0.3
1
VREF–0.04
VREF+0.15
–0.3
VREF
—
1
VIH(DC)
VIL(DC)
VIN (DC)
1, 3, 8
1, 4, 8
5
—
VREF–0.15
VCCQ + 0.3
DC Input signal voltage
(CLK, /CLK)
–0.3
—
DC differential input voltage
(CLK, /CLK)
VID (DC)
0.36
—
VCCQ + 0.6
V
6, 7
Notes: 1. All parameters are referred to VSS, when measured.
2. VCCQ must be lower than or equal to VCC.
3. VIH is allowed to exceed VCC up to 3.6 V for the period shorter than or equal to 5 ns.
4. VIL is allowed to outreach below VSS down to –1.0 V for the period shorter than or equal to 5 ns.
5. VIN (dc) specifies the allowable dc execution of each differential input.
6. VID (dc) specifies the input differential voltage required for switching.
7. VIH (CLK) min assumed over VREF + 0.15 V, VIL(CLK) max assumed under VREF – 0.15 V.
8. VIH (DC) and VIL (DC) are levels to maintain the current logic state.
Data Sheet E0086H20
43
HM5425161B, HM5425801B, HM5425401B Series
DC Characteristics 1 (Ta = 0 to +70˚C, VCC, VCCQ = 2.5 V ± 0.2 V, VSS, VSSQ = 0 V)
Parameter
Symbol
ILI
Min
–2
Max
2
Unit
µA
µA
V
Test conditions
VCC ≥ Vin ≥ VSS
Notes
Input leakage current
Output leakage current
Output high voltage
Output low voltage
ILO
–5
5
VCCQ ≥ Vout ≥ VSSQ
IOH (max) = –15.2 mA
IOL (min) = 15.2 mA
VOH
1.95
—
—
VOL
0.35
V
Data Sheet E0086H20
44
HM5425161B, HM5425801B, HM5425401B Series
Data Driver Output Characteristic Curves
1. The full variation in driver pulldown current from minimum to maximum temperature and voltage will lie
within the outer bounding lines of the V-I curve of the figure “Pull-down Characteristics”.
150
Maximum
125
Typical High
100
75
Typical Low
50
Minimum
25
0
0
0.2 0.4 0.6 0.8
1
1.2 1.4 1.6 1.8
2
2.2 2.4 2.6 2.8
VOUT to VSSQ (V)
Pull-down Characteristics
2. The full variation in driver pullup current from minimum to maximum temperature and voltage will lie
within the outer bounding lines of the V-I curve of the figure “Pull-up Characteristics”.
0
Minimum
-25
-50
Typical Low
Typical High
-75
-100
-125
-150
Maximum
-175
-200
0
0.2 0.4 0.6 0.8
1
1.2 1.4 1.6 1.8
2
2.2 2.4 2.6 2.8
VDDQ to VOUT (V)
Pull-up Characteristics
5. The full variation in the ratio of the maximum to minimum pullup and pulldown current will not exceed
1.7 for device drain to source voltages from 0.1 to 1.0.
6. The full variation in the ratio of the typical IBIS pullup to typical IBIS pulldown current should be unity
±10%, for device drain to source voltages from 0.1 to 1.0. This specification is a design objective only.
7. These characteristics obey the SSTL_2 class II standard.
Data Sheet E0086H20
45
HM5425161B, HM5425801B, HM5425401B Series
Data Driver Output Characteristic V-I data points
Evaluation Conditions
•
•
•
Typical: Ta = 25°C, VCCQ = 2.5 V
Minimum: Ta = 70°C, VCCQ = 2.3 V
Maximum: Ta = 0°C, VCCQ = 2.7 V
Pull-down current (mA)
Pull-up current (mA)
Typical
Voltage (V) Low
Typical
High
Typical
Minimum Maximum Low
Typical
High
Minimum Maximum
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
6.0
6.8
4.6
9.6
–6.1
–7.6
–4.6
–10.0
12.2
18.1
24.1
29.8
34.6
39.4
43.7
47.5
51.3
54.1
56.2
57.9
59.3
60.1
60.5
61.0
61.5
62.0
62.5
62.9
63.3
63.8
64.1
64.6
64.8
65.0
13.5
20.1
26.6
33.0
39.1
44.2
49.8
55.2
60.3
65.2
69.9
74.2
78.4
82.3
85.9
89.1
92.2
95.3
97.2
99.1
100.9
101.9
102.8
103.8
104.6
105.4
9.2
18.2
–12.2
–18.1
–24.0
–29.8
–34.3
–38.1
–41.1
–43.8
–46.0
–47.8
–49.2
–50.0
–50.5
–50.7
–51.0
–51.1
–51.3
–51.5
–51.6
–51.8
–52.0
–52.2
–52.3
–52.5
–52.7
–52.8
–14.5
–21.2
–27.7
–34.1
–40.5
–46.9
–53.1
–59.4
–65.5
–71.6
–77.6
–83.6
–89.7
–95.5
–101.3
–107.1
–112.4
–118.7
–124.0
–129.3
–134.6
–139.9
–145.2
–150.5
–155.3
–160.1
–9.2
–20.0
13.8
18.4
23.0
27.7
32.2
36.8
39.6
42.6
44.8
46.2
47.1
47.4
47.7
48.0
48.4
48.9
49.1
49.4
49.6
49.8
49.9
50.0
50.2
50.4
50.5
26.0
–13.8
–18.4
–23.0
–27.7
–32.2
–36.0
–38.2
–38.7
–39.0
–39.2
–39.4
–39.6
–39.9
–40.1
–40.2
–40.3
–40.4
–40.5
–40.6
–40.7
–40.8
–40.9
–41.0
–41.1
–41.2
–29.8
33.9
–38.8
41.8
–46.8
49.4
–54.4
56.8
–61.8
63.2
–69.5
69.9
–77.3
76.3
–85.2
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
2
82.5
–93.0
88.3
–100.6
–108.1
–115.5
–123.0
–130.4
–136.7
–144.2
–150.5
–156.9
–163.2
–169.6
–176.0
–181.3
–187.6
–192.9
–198.2
93.8
99.1
103.8
108.4
112.1
115.9
119.6
123.3
126.5
129.5
132.4
135.0
137.3
139.2
140.8
2.1
2.2
2.3
2.4
2.5
2.6
2.7
Data Sheet E0086H20
46
HM5425161B, HM5425801B, HM5425401B Series
DC Characteristics 2*1 (Ta = 0 to +70˚C, VCC, VCCQ = 2.5 V ± 0.2 V, VSS, VSSQ = 0 V)
Max
Parameter
Symbol
I/O
-75A
-75B
-10
Unit
Operating current (ACTV- ICC0
PRE)
100
95
80
mA
Operating current (ACTV- ICC1
READ-PRE)
155
18
145
15
130
12
mA
mA
Idle power down standby ICC2P
current
Idle standby current
ICC2N
ICC3P
40
25
35
20
30
15
mA
mA
Active power down
standby current
Active standby current
ICC3N
ICC4R
50
45
40
mA
mA
Operating current
(Burst read operation)
× 4, × 8 225
× 16 255
215
245
205
235
Operating current
(Burst write operation)
ICC4W
× 4, × 8 205
195
230
185
220
mA
× 16
240
205
3
Auto Refresh current
Self refresh current
Random read current
ICC5
ICC6
ICC7A
200
3
180
3
mA
mA
mA
× 4, × 8 330
× 16 360
320
350
310
340
Notes: 1. These ICC data are measured under condition that DQ pins are not connected.
Data Sheet E0086H20
47
HM5425161B, HM5425801B, HM5425401B Series
ICC Measurement Condition
Parameter
Symbol Condition
ICC0 One Bank ; CKE ≥ VIH(min), tRC = tRC (min); tCK = tCK (min);
Operating current
(ACTV-PRE)
DQ, DM and DQS inputs changing twice per clock cycle; address
and control inputs changing once per clock cycle
Operating current
(ACTV-READ-PRE)
ICC1
One Bank; CKE ≥ VIH(min); Burst = 2; tRC = tRC (min); CL = 2.5; tCK
= tCK (min); Iout = 0 mA; address and control inputs changing once
per clock cycle
Idle power down standby
current
ICC2P
ICC2N
All banks idle; power down mode; CKE ≤ VIL(max); tCK = tCK (min).
Vin = VREF for DQ, DQS and DM
Idle standby current
All banks idle; CS ≥ VIH (min); CKE ≥ VIH (min); tCK = tCK (min);
Address and other control inputs changing once per clock cycle.
Vin ≥ VIH(min) or Vin ≤ VIL(max) for DQ, DQS and DM.
Active power down standby ICC3P
current
One bank active; power down mode; CKE ≤ VIL (max); tCK = tCK
(min)
Active standby current
ICC3N
One bank; Active Precharge; CS ≥ VIH (min); CKE ≥ VIH (min); tRC =
tRAS (max); tCK = tCK (min); DQ,DM and DQS inputs changing twice
per clock cycle; address and other control inputs changing once
per clock cycle
Operating current
(Burst read operation)
ICC4R
One bank active ; CKE ≥ VIH(min); Burst = 2; Reads; Continuous
burst; address and control inputs changing once per clock cycle;
CL = 2.5; tCK = tCK (min); Iout = 0 mA;
Operating current
(Burst write operation)
ICC4W
One bank active; CKE ≥ VIH(min); Burst = 2; Writes; Continuous
burst; address and control inputs changing once per clock cycle;
CL = 2.5; tCK = tCK (min); DQ, DM and DQS inputs changing twice
per clock cycle
Auto refresh current
Self refresh current
Random read current
ICC5
ICC6
ICC7A
tRC = tRFC (min); Vin ≤ VIL(max) or ≥ VIH(min)
CKE ≤ 0.2 V, Vin ≤ 0.2V or ≥ VCCQ–0.2V
4 banks active read with activate every 2 clocks, AP (Auto
Precharge) read every 2 clocks, BL = 4, tRCD =3, Iout = 0 mA,
100% DQ, DM and DQS inputs changing twice per clock cycle;
100% addresses changing once per clock cycle.
Data Sheet E0086H20
48
HM5425161B, HM5425801B, HM5425401B Series
Capacitance (Ta = 25°C, VCC, VCCQ = 2.5 V ± 0.2 V)
Parameter
Symbol
Min
2
Max
3
Unit
pF
Notes
Input capacitance (CLK, CLK)
CI1
1
1
Input capacitance (input only pins; including CKE CI2
2
3
pF
but not including CLK, CLK)
Input/output capacitance (DQ, DM, DQS)
Delta input /output capacitance (DQ, DM, DQS) CIOD
Delta input capacitance (CLK, CLK only) CID
CIO
4
5
pF
pF
pF
1, 2
1
0.5
0.25
1
Notes: 1. These parameters are measured on conditions: f = 100 MHz, Vout = VCCQ/2, ∆Vout = 0.2 V.
2. Dout circuits are disabled.
Data Sheet E0086H20
49
HM5425161B, HM5425801B, HM5425401B Series
AC Characteristics (Ta = 0 to +70˚C, VCC, VCCQ = 2.5 V ± 0.2 V, VSS, VSSQ = 0 V)
HM5425161B/HM542581B/HM5425401B
-75A
-75B
Min
-10
Parameter
Symbol Min
Max
Max
Min
Max
Unit Notes
Clock cycle time
(CAS latency = 2)
tCK
tCK
7.5
7
12
10
12
10
12
ns
ns
tCK
tCK
tCK
10
(CAS latency = 2.5)
12
7.5
12
8
12
Input clock high level time tCH
0.45
0.45
0.55
0.55
—
0.45
0.45
0.55
0.55
—
0.45
0.45
0.55
0.55
—
Input clock low level time
CLK half period
tCL
tHP
min
min
min
(tCH, tCL)
(tCH, tCL)
(tCH, tCL)
CLK to DQS skew
DATA to CLK skew
Dout to DQS skew
tDQSCK
tAC
tDQSQ
tQH
–0.75
–0.75
—
0.75
0.75
0.5
–0.75
–0.75
—
0.75
0.75
0.5
–0.8
0.8
0.8
0.6
—
ns
ns
ns
tCK
2, 11
2, 11
3
–0.8
—
DQ/DQS output skew
hold time
tHP – tQHS
—
tHP – tQHS
—
tHP – tQHS
Data hold skew factor
Dout/DQS valid window
DQS valid window
tQHS
tDV
—
0.75
—
—
0.75
—
—
1.0
—
ns
tCK
tCK
tCK
tCK
ns
0.35
0.35
0.9
0.35
0.35
0.9
0.35
0.35
0.9
tDQSV
tRPRE
tRPST
—
—
—
DQS read preamble
DQS read postamble
1.1
0.6
0.75
1.1
0.6
0.75
1.1
0.6
0.8
0.4
0.4
0.4
Dout-High impedance delay tHZ
–0.75
–0.75
–0.8
5, 11
from CLK/CLK
Dout-Low impedance delay tLZ
from CLK/CLK
–0.75
1.75
0.5
0.75
—
–0.75
1.75
0.5
0.75
—
–0.8
2
0.8
—
ns
ns
ns
ns
ns
tCK
tCK
6, 11
DQ and DM input pulse
width
tDIPW
7
8
8
Data and data mask to data tDS
strobe setup time
—
—
0.6
0.6
0
—
Data and data mask to data tDH
strobe hold time
0.5
—
0.5
—
—
Clock to DQS write
preamble setup time
tWPRES
tWPREH
tWPST
0
—
0
—
—
Clock to DQS write
preamble hold time
0.25
0.4
—
0.25
0.4
—
0.25
0.4
—
DQS last edge to High-Z
0.6
0.6
0.6
9
time (DQS write postamble)
Data Sheet E0086H20
50
HM5425161B, HM5425801B, HM5425401B Series
HM5425161B/HM5425801B/HM5425401B
-75A
-75B
Min
-10
Parameter
Symbol Min
Max
Max
Min
0.75
Max
Unit Notes
Clock to the DQS first rising
edge for write delay
tDQSS
0.72
1.28
0.72
1.28
1.25
tCK
DQS falling edge to CLK setup tDSS
time
0.2
—
—
—
—
—
—
—
0.2
0.2
0.35
0.35
0.9
0.9
20
—
—
—
—
—
—
—
0.2
0.2
0.35
0.35
1.1
1.1
20
—
—
—
—
—
—
—
tCK
tCK
tCK
tCK
DQS falling edge hold time to tDSH
CLK
0.2
DQS high pulse width
(DQS write)
tDQSH
tDQSL
tIS
0.35
0.35
0.9
DQS low pulse width
(DQS write)
Input command and address
setup time
ns
ns
ns
8
8
Input command and address
hold time
tIH
0.9
RAS to READ (with auto
precharge)
tRAP
20
Active command period
tRC
65
75
—
—
65
75
—
—
70
80
—
—
ns
ns
Auto refresh to active/Auto
refresh command cycle
tRFC
Active to Precharge command tRAS
period
45
20
120000 45
120000 50
120000 ns
Active to column command
period
tRCD
—
20
—
20
—
ns
Write recovery time
tWR
15
35
—
—
15
35
—
—
15
40
—
—
ns
ns
Auto precharge write recovery tDAL
and precharge time
Precharge to active command tRP
period
20
15
—
—
20
15
—
—
20
15
—
—
ns
ns
µs
Active to active command
period
tRRD
—
—
—
Average periodic refresh
interval
tREF
7.8
7.8
7.8
Data Sheet E0086H20
51
HM5425161B, HM5425801B, HM5425401B Series
Notes: 1. On all AC measurements, we assume the test conditions shown in the next page. For timing
parameter definitions, see ‘Timing Waveforms’ section.
2. This parameter defines the signal transition delay from the cross point of CLK and CLK. The signal
transition is defined to occur when the signal level crossing VTT.
3. The timing reference level is VTT.
4. Output valid window is defined to be the period between two successive transition of data out or
DQS (read) signals. The signal transition is defined to occur when the signal level crossing VTT.
5. tHZ is defined as Dout transition delay from Low-Z to High-Z at the end of read burst operation. The
timing reference is cross point of CLK and CLK. This parameter is not referred to a specific Dout
voltage level, but specify when the device output stops driving.
6. tLZ is defined as Dout transition delay from High-Z to Low-Z at the beginning of read operation. This
parameter is not referred to a specific Dout voltage level, but specify when the device output begins
driving.
7. Input valid windows is defined to be the period between two successive transition of data input or
DQS (write) signals. The signal transition is defined to occur when the signal level crossing VREF
.
8. The timing reference level is VREF
.
9. The transition from Low-Z to High-Z is defined to occur when the device output stops driving. A
specific reference voltage to judge this transition is not given.
10. tCK max is determined by the lock range of the DLL. Beyond this lock range, the DLL operation is
not assured.
11. tCK = min when these parameters are measured. Otherwise, absolute minimum value of these
values are 10% of tCK.
12. VCC is assumed to be 2.5 V ± 0.2 V. VCC power supply variation per cycle expected to be less than
0.4 V/400 cycle.
Data Sheet E0086H20
52
HM5425161B, HM5425801B, HM5425401B Series
Test Conditions
Parameter
Symbol
VREF(AC)
VTT (AC)
VIH (AC)
VIL (AC)
Min
Typ
Max
Unit
Input reference voltage
Termination voltage
AC input high voltage
AC input low voltage
0.5×VCCQ–0.05
VREF(AC) − 0.04
VREF (AC) + 0.31
—
0.5 × VCCQ
0.5×VCCQ+0.05
V
VREF(AC)
VREF (AC) + 0.04 V
—
—
—
—
V
VREF (AC) − 0.31 V
VCCQ + 0.6 V
AC differential input voltage (CLK, VID (AC)
0.7
CLK)
AC differential cross point voltage VX (AC)
(CLK, CLK)
0.5 × VCCQ − 0.2
0.5 × VCCQ
0.5 × VCCQ + 0.2 V
V/ns
Input signal slew rate
SLEW
—
1
—
tCK
VCC
CLK
VREF (AC)
VX(AC)
VSS
VID(AC)
CLK
tCL
tCH
VCC
VREF
VIH
VIL
VSS
∆t
SLEW = (VIH (AC) – VIL (AC))/∆t
VTT
Measurement point
DQ
RT = 50 Ω
CL = 30 pF
Data Sheet E0086H20
53
HM5425161B, HM5425801B, HM5425401B Series
Timing Parameter Measured in Clock Cycle
Number of clock cycle
Parameter
Symbol
tWPD
Min
Max
Write to pre-charge command delay (same bank)
Read to pre-charge command delay (same bank)
Write to read command delay (to input all data)
3 + BL/2
BL/2
tRPD
tWRD
2 + BL/2
2
Burst stop command to write command delay
tBSTW
(CAS latency = 2)
(CAS latency = 2.5)
tBSTW
tBSTZ
3
2
Burst stop command to DQ High-Z
(CAS latency = 2)
(CAS latency = 2.5)
tBSTZ
2.5
Read command to write command delay (to output all data) tRWD
2 + BL/2
(CAS latency = 2)
(CAS latency = 2.5)
tRWD
tHZP
3 + BL/2
2
Pre-charge command to High-Z
(CAS latency = 2)
(CAS latency = 2.5)
tHZP
2.5
1
Write command to data in latency
Auto precharge write recovery and precharge time
Write recovery
tWCD
tDAL
5
tWR
2
DM to data in latency
tDMD
tMRD
tSNR
tSRD
tPDEN
tPDEX
tCKEPW
0
Register set command to active or register set command
Self refresh exit to non-read command
Self refresh exit to read command
Power down entry
2
10
200
1
Power down exit to command input
CKE minimum pulse width
1
1
Data Sheet E0086H20
54
HM5425161B, HM5425801B, HM5425401B Series
Timing Waveforms
Command and Addresses Input Timing Definition
CLK
CLK
tIS
tIH
Command
(RAS, CAS,
WE, CS)
V
V
REF
tIS
tIH
Address
REF
Read Timing Definition
tCK
CLK
CLK
tCL
tRPRE
tCH
tDQSCK
tDQSCK
tDQSCK
tDQSCK
tDQSCK
tDQSCK tRPST
DQS
tDQSQ
tDQSQ
tAC
tQH
tAC
tQH
tAC
tLZ
tAC
tHZ
DQ
(Dout)
tDQSQ
tDQSQ
tQH
tQH
tQH
Data Sheet E0086H20
55
HM5425161B, HM5425801B, HM5425401B Series
Write Timing Definition
tCK
CLK
CLK
tDQSS
tDSS
tDSH
tDSS
VREF
VREF
VREF
DQS
tDQSL
tDQSH
tWPST
tWPRES
tWPREH
DQ
(Din)
tDIPW
tDS
tDH
DM
tDS
tDH
tDIPW
tDIPW
Data Sheet E0086H20
56
HM5425161B, HM5425801B, HM5425401B Series
Read Cycle
tCK
tCH tCL
CLK
CLK
tRC
VIH
CKE
tRAS
tRP
tRCD
tIS tIH
tIS tIH
tIS tIH
tIS tIH
CS
tIS tIH
tIS tIH
tIS tIH
tIS tIH
RAS
tIS tIH
tIS tIH
tIS tIH
tIS tIH
CAS
tIS tIH
tIS tIH
tIS tIH
tIS tIH
WE
tIS tIH
tIS tIH
tIS tIH
tIS tIH
BA
tIS tIH
tIS tIH
tIS tIH
tIS tIH
A10
tIS tIH
tIS tIH
tIS tIH
Address
DM,
DMU/DML
tRPRE tDQSV DQSV
t
tRPST
High-Z
DQS,
DQSU/DQSL
tDV tDV
High-Z
DQ (output)
Bank 0
Active
Bank 0
Read
Bank 0
Precharge
CAS latency = 2
Burst length = 4
Bank0 Access
= VIH or VIL
Data Sheet E0086H20
57
HM5425161B, HM5425801B, HM5425401B Series
Write Cycle
tCK
tCH
tCL
CLK
CLK
tRC
VIH
CKE
tRAS
tRP
tRCD
tIS tIH
tIS tIH
tIS tIH
tIS tIH
tIS tIH
tIS tIH
tIS tIH
tIS tIH
CS
tIS tIH
tIS tIH
RAS
CAS
WE
tIS tIH
tIS tIH
tIS tIH
tIS tIH
tIS tIH
tIS tIH
tIS
tIH
tIS tIH
tIS tIH
tIS tIH
BA
tIS tIH
tIS tIH
tIS tIH
tIS tIH
A10
tIS tIH
tIS tIH
tIS tIH
Address
tDQSS
tDQSL
tWPST
DQS,
DQSU/DQSL
(input)
tDQSL
tDS
tDH
tDS
DM,
DMU/DML
tDS
tDH
DQ (input)
tWR
tDH
CAS latency = 2
Burst length = 4
Bank0 Access
= VIH or VIL
Bank 0
Active
Bank 0
Write
Bank 0
Precharge
Data Sheet E0086H20
58
HM5425161B, HM5425801B, HM5425401B Series
Mode Register Set Cycle
0
1
2
3
4
5
6
7
8
9
10
11
12
13 14
15
CLK
CLK
VIH
CKE
CS
RAS
CAS
WE
BA
code
code
Address
C: b
R: b
valid
DM,
DMU/DML
High-Z
High-Z
DQS,
DQSU/DQSL
b
DQ (output)
tMRD
tRP
Bank 3
Read
Bank 3
Precharge
Mode
register
set
Bank 3
Active
CAS latency = 2
Burst length = 4
= VIH or VIL
Precharge
If needed
Data Sheet E0086H20
59
HM5425161B, HM5425801B, HM5425401B Series
Read/Write Cycle
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
CLK
CLK
CKE
VIH
CS
RAS
CAS
WE
BA
Address
R:a
C:b''
C:a R:b
C:b
DM,
DMU/DML
DQS,
DQSU/DQSL
a
b’’
DQ (output)
DQ (input)
High-Z
b
tRWD
tWRD
Bank 0
Active
Bank 0 Bank 3
Read Active
Bank 3
Write
Bank 3
Read
Read cycle
CAS latency = 2
Burst lenght = 4
=VIH or VIL
Data Sheet E0086H20
60
HM5425161B, HM5425801B, HM5425401B Series
Auto Refresh Cycle
CLK
CLK
VIH
CKE
CS
RAS
CAS
WE
BA
Address
A10=1
R: b
C: b
DM,
DMU/DML
DQS
DQSU/DQSL
b
DQ (output)
High-Z
DQ (input)
tRP
tRFC
Precharge
If needed
Auto
Refresh
Bank 0
Active
Bank 0
Read
CAS latency = 2
Burst length = 4
= VIH or VIL
Data Sheet E0086H20
61
HM5425161B, HM5425801B, HM5425401B Series
Self Refresh Cycle
CLK
CLK
tIS
tIH
CKE
CKE = low
tCKEPW
CS
RAS
CAS
WE
BA
Address
A10=1
R: b
C: b
DM,
DMU/DML
DQS
DQSU/DQSL
DQ (output)
DQ (input)
High-Z
tSNR
tSRD
tRP
Precharge
If needed
Self
refresh
entry
Self refresh
exit
Bank 0
Active
Bank 0
Read
CAS latency = 2.5
Burst length = 4
= VIH or VIL
Data Sheet E0086H20
62
HM5425161B, HM5425801B, HM5425401B Series
Power Down Mode
CLK
CLK
tIS
tIH
CKE = low
CKE
tCKEPW
CS
RAS
CAS
WE
BA
Address
A10=1
R: b
R: c
DM,
DMU/DML
QS,
QSU/QSL
DQ (output)
DQ (input)
High-Z
tRP
tPDEX
Power Bank 0
tPDEN
Precharge
If needed
Power down
entry
Bank 0
Read
down
exit
Active
CAS latency = 2.5
Burst lenght = 4
=VIH or VIL
Data Sheet E0086H20
63
HM5425161B, HM5425801B, HM5425401B Series
Package Dimensions
HM5425161BTT/HM5425801BTT/HM5425401BTT Series
Unit: mm
*1
22.22 ± 0.10
A
66
34
PIN#1 ID
1
0.17 to 0.32
0.91 max.
33
B
B
0.65
M
S
S A
0.13
0.80
Nom
0.25
0 to 8°
0.10
S
0.60 ± 0.15
Note: This dimension does not include mold flash, protrusions or gate burrs. Mold flash, protrusions or
gate burrs shall not exceed 0.20mm per side.
ECA-TS2-0029-01
Data Sheet E0086H20
64
HM5425161B, HM5425801B, HM5425401B Series
Cautions
1. Elpida Memory, Inc. neither warrants nor grants licenses of any rights of Elpida Memory, Inc.’s or any
third party’s patent, copyright, trademark, or other intellectual property rights for information contained in
this document. Elpida Memory, Inc. bears no responsibility for problems that may arise with third party’s
rights, including intellectual property rights, in connection with use of the information contained in this
document.
2. Products and product specifications may be subject to change without notice. Confirm that you have
received the latest product standards or specifications before final design, purchase or use.
3. Elpida Memory, Inc. makes every attempt to ensure that its products are of high quality and reliability.
However, contact Elpida Memory, Inc. before using the product in an application that demands especially
high quality and reliability or where its failure or malfunction may directly threaten human life or cause
risk of bodily injury, such as aerospace, aeronautics, nuclear power, combustion control, transportation,
traffic, safety equipment or medical equipment for life support.
4. Design your application so that the product is used within the ranges guaranteed by Elpida Memory, Inc.
particularly for maximum rating, operating supply voltage range, heat radiation characteristics, installation
conditions and other characteristics. Elpida Memory, Inc. bears no responsibility for failure or damage
when used beyond the guaranteed ranges. Even within the guaranteed ranges, consider normally
foreseeable failure rates or failure modes in semiconductor devices and employ systemic measures such as
fail-safes, so that the equipment incorporating Elpida Memory, Inc. product does not cause bodily injury,
fire or other consequential damage due to operation of the Elpida Memory, Inc. product.
5. This product is not designed to be radiation resistant.
6. No one is permitted to reproduce or duplicate, in any form, the whole or part of this document without
written approval from Elpida Memory, Inc..
7. Contact Elpida Memory, Inc. for any questions regarding this document or Elpida Memory, Inc.
semiconductor products.
© Hitachi, Ltd., 2000
Data Sheet E0086H20
65
相关型号：
HM5425161BTT-10
256M SSTL_2 interface DDR SDRAM 143 MHz/133 MHz/125 MHz/100 MHz 4-Mword 】 16-bit 】 4-bank/8-Mword 】 8-bit 】 4-bank/ 16-Mword 】 4-bit 】 4-bank
ELPIDA
HM5425161BTT-75A
256M SSTL_2 interface DDR SDRAM 143 MHz/133 MHz/125 MHz/100 MHz 4-Mword 】 16-bit 】 4-bank/8-Mword 】 8-bit 】 4-bank/ 16-Mword 】 4-bit 】 4-bank
ELPIDA
HM5425161BTT-75B
256M SSTL_2 interface DDR SDRAM 143 MHz/133 MHz/125 MHz/100 MHz 4-Mword 】 16-bit 】 4-bank/8-Mword 】 8-bit 】 4-bank/ 16-Mword 】 4-bit 】 4-bank
ELPIDA
HM5425401B
256M SSTL_2 interface DDR SDRAM 143 MHz/133 MHz/125 MHz/100 MHz 4-Mword 】 16-bit 】 4-bank/8-Mword 】 8-bit 】 4-bank/ 16-Mword 】 4-bit 】 4-bank
ELPIDA
HM5425401BTT-10
256M SSTL_2 interface DDR SDRAM 143 MHz/133 MHz/125 MHz/100 MHz 4-Mword 】 16-bit 】 4-bank/8-Mword 】 8-bit 】 4-bank/ 16-Mword 】 4-bit 】 4-bank
ELPIDA
HM5425401BTT-75A
256M SSTL_2 interface DDR SDRAM 143 MHz/133 MHz/125 MHz/100 MHz 4-Mword 】 16-bit 】 4-bank/8-Mword 】 8-bit 】 4-bank/ 16-Mword 】 4-bit 】 4-bank
ELPIDA
HM5425401BTT-75B
256M SSTL_2 interface DDR SDRAM 143 MHz/133 MHz/125 MHz/100 MHz 4-Mword 】 16-bit 】 4-bank/8-Mword 】 8-bit 】 4-bank/ 16-Mword 】 4-bit 】 4-bank
ELPIDA
HM5425801B
256M SSTL_2 interface DDR SDRAM 143 MHz/133 MHz/125 MHz/100 MHz 4-Mword 】 16-bit 】 4-bank/8-Mword 】 8-bit 】 4-bank/ 16-Mword 】 4-bit 】 4-bank
ELPIDA
HM5425801BTT-10
256M SSTL_2 interface DDR SDRAM 143 MHz/133 MHz/125 MHz/100 MHz 4-Mword 】 16-bit 】 4-bank/8-Mword 】 8-bit 】 4-bank/ 16-Mword 】 4-bit 】 4-bank
ELPIDA
HM5425801BTT-75A
256M SSTL_2 interface DDR SDRAM 143 MHz/133 MHz/125 MHz/100 MHz 4-Mword 】 16-bit 】 4-bank/8-Mword 】 8-bit 】 4-bank/ 16-Mword 】 4-bit 】 4-bank
ELPIDA
HM5425801BTT-75B
256M SSTL_2 interface DDR SDRAM 143 MHz/133 MHz/125 MHz/100 MHz 4-Mword 】 16-bit 】 4-bank/8-Mword 】 8-bit 】 4-bank/ 16-Mword 】 4-bit 】 4-bank
ELPIDA
©2020 ICPDF网 联系我们和版权申明