OPG-UR-V-ZZ [EMCORE]
openGear® OPG-1L 50 MHz â 2.3 GHz RF Fiber Optic Link;
| 型号： | OPG-UR-V-ZZ |
| 厂家： | 
EMCORE CORPORATION |
| 描述： | openGear® OPG-1L 50 MHz â 2.3 GHz RF Fiber Optic Link |
| 文件： | 总4页 (文件大小：1727K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
openGear® OPG-1L 50 MHz – 2.3 GHz
RF Fiber Optic Link
DATASHEET | OCTOBER 2013
SATCOM
EMCORE’s openGear® OPG-1L RF Fiber Optic Links are optimized
to perform in the 50 MHz to 2.3 GHz frequency range providing
transparent signal transport for satellite antenna applications on an
open architecture platform.
The OPG-1L transmitter and receiver modules may be housed in the
same chassis as EMCORE’S openGear® HD video, audio, serial data
and USB extension / distribution cards, allowing full monitoring and control of
each module via the DashBoard Network Management System (NMS).
System Design
Features
The OPG-1L was designed to be fully compatible
50 MHz to 2.3 GHz Optimized for IF- and
with the openGear® standard for terminal equip-
L-Band Video Signals
ment or cable headend design. This means that
when you install an openGear® enclosure, you
Supports 30 km Links**
can then purchase additional insert cards from
Optically-Isolated DFB Lasers Enable High-
Dynamic-Range Links
different manufacturers to be used in the same enclosure. The standard enclosure
is a 19” rack-mount frame that can hold up to 20 insert cards. A separate module
handles the management and control systems, and allows for local or remote
interfaces. Each enclosure utilizes 2 RU of rack space, maximizing the overall usage
of the equipment rack.
25 dB Tx and Rx Adjustable Gain Range
Peak Optimizer for Quick and Easy Set-Up
SmartGain for Enhanced AGC Performance
50 & 75 Ohm BNC or 50 Ohm SMA
The OPG-1L’s Rear Interface Modules may be pre-installed with its cabling, with-
out corresponding PCBA cards. This allows the user to anticipate future expansion
needs without significantly increasing the intial investment, and without having to
access the rear panel and cabling once installed. The user simply purchases corre-
sponding PCBA cards on an as-needed basis then slides them into place from the
front of the frame, effortlessly locking them into the Rear Interface Module.
Blind Mate RF Coax to Support Rear Plug-in
Access
SC/APC and LC/APC Optical Connectors
Tx & Rx RF Power Monitors Via LED, SMA,
Dashboard and SNMP
Block Diagram
Transmitter
Dashboard and SNMP Monitoring and Control
LNB Power Capable
Receiver
DC to LNB
S
PL
P
R
in
Laser
S
S
Photodiode
Tx and Rx PCBA Card and Module
2 RU, 20-Slot openGear® Enclosure
CE & CSA Certified, RoHS
out
Push
Button
Optimizer
mon
S
mon
**For higher optics, please contact us
© 2013 EMCORE Corporation | REV 2013.10
+1 626-293-3400
satcom-sales@emcore.com
www.emcore.com
Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice.
openGear® OPG-1L 50 MHz – 2.3 GHz
RF Fiber Optic Link
DATASHEET | OCTOBER 2013
SATCOM
Performance Highlights
Frame Options
Parameter
Value
1310, 1550
5 + 2
Units
nm
TX
Wavelength
Optical Output Power
dBmo
IF-Band Frequency
L-Band Frequency
50-1000
MHz
MHz
850-2300
OPG-8321
Frequency Response
Any 500 MHz
+ 0.75
+ 1.5
dB
dB
Full Band (50-2300 MHz)
Input Return Loss (minimum)
10
dB
dB
Total Front-End RF Gain1 (at minimum attenuation setting)
Attenuation Adjustment Range
25 + 2
30
98
dB
OG3-FR
OPG-1L
Spurs Free Dynamic Range2
dB-Hz2/3
dB
Noise Figure (at maximum gain, 25°C)
Input IP3 (at maximum gain, 25°C)
Total RF Power Into Laser
23
-4
dBm
dBm
dB
2 + 2dB
10
RX
Output Return Loss (Minimum)
Total Front-End RF Gain1 (at minimum attentuation setting)
20 (dual output)
25 (single output)
dB
Attenuation Adjustment Range
15
dB
Output IP3 (at maximum gain, 25°C)
20 (dual output)
25 (single output)
dBm
1. Link RF Gain dB = TG + RG - 2*Fiber Loss dBo
2. SFDR = 2/3*(IIP3 + 174 - NF).
PCBA Cards with Rear Interface Modules
Mechanical Characteristics
Value1
Parameter
Units
PCBA Card Dimension
12.8 L x 3.0 H x 0.681 W
32.5 L x 7.62 H x 0.173W
in
cm
PCBA Cards
Rear Interface Module Dimension
1.362 L x 3.365 H x 1.31 W
3.46 L x 8.55 H x 3.33 W
in
cm
1. Defined per openGear Development Guide by Ross: 8200DR-001-02, 8200DR-001-03
Electrical Characteristics
Parameter
Value
12
Units
W
TX
Power Requirement
Input Voltage (@ 1 A Max)
LNB Voltage (at RF input port, 350 mA max)
DC Current (@ +12 V with LNB Off)
Input Voltage (@ 1 A Max)
DC Current (@ +12 V)
12 +/- 0.5
17 +/- 1.0
350 +/- 50
12 +/- 0.5
250 +/- 50
VDC
VDC
mA
Rear Interface Modules
RX
VDC
mA
© 2013 EMCORE Corporation | REV 2013.10
+1 626-293-3400
satcom-sales@emcore.com
www.emcore.com
Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice.
openGear® OPG-1L 50 MHz – 2.3 GHz
RF Fiber Optic Link
DATASHEET | OCTOBER 2013
SATCOM
Card Compatibility to openGear® Frames
© 2013 EMCORE Corporation | REV 2013.10
+1 626-293-3400
satcom-sales@emcore.com
www.emcore.com
Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice.
openGear® OPG-1L 50 MHz – 2.3 GHz
RF Fiber Optic Link
DATASHEET | OCTOBER 2013
SATCOM
Ordering Information PCBA Card
Transmitter1
Receiver
OPG-UT-YY05-ZZ
OPG-UR-V-ZZ
Note 1. When installing transmitter cards in the OG3-FR frame, remove the pre-installed
LNB blocker plug from the PCBA card but leave as-is for the OPG-8321 frame to
prevent the frame’s DC-power alarm from activating.
When ordering replace “U” with one of the Frequency Band Options
When ordering replace “V” with one of the RX Only: RF Interface Options
When ordering replace “YY” with one of the Wavelength Options**
When ordering replace “ZZ” with one of the Optical Connector Options
Frequency
Band Options
“U”
Frequency
Band
(MHz)
RX Only:
RF Interface Options
“V”
Wavelength
Options (nm)
“YY”
Output Power Optical Connector Options
(dBmo) “ZZ”
I = IF-Band
50-1000
1 = Output+Monitor
2 = Dual Outputs
13 = 1310,
55 = 1550
05 = +5
05 = +5
LA = LC-APC,
SA = SC-APC (OG3-FR only)
L = L-Band
850-2300
1 = Output+Monitor
2 = Dual Outputs
13 = 1310,
55 = 1550
LA = LC-APC,
SA = SC-APC (OG3-FR only)
Ordering Information for Rear Interface Module (RIM)
Transmitter/Receiver
RF Connector
Options
“W”
RF Connector
Impedance
Options (ohm)
“X”
OPG-WX
B = BNC,
S = SMA
5 = 50,
7 = 75 (BNC only)
When ordering replace “W” with one of the RF Connector Options
When ordering replace “X” with one of the RF Connector Impedance Options
Laser Safety
This product meets the appropriate standard in Title 21 of the Code of Federal Regulations (CFR). FDA/CDRH Class 1M laser
product. This device has been classified with the FDA/CDRH under accession number 0220191. All versions of this laser are Class
1M laser product, tested according to IEC 60825-1:2007 / EN 60825-1:2007. An additional warning for Class 1M laser products.
For diverging beams, this warning shall state that viewing the laser output with certain optical instruments (for example: eye
loupes, magnifiers, and microscopes) within a distance of 100 mm may pose an eye hazard. For collimated beams, this warning
shall state that viewing the laser output with certain instruments designed for use at a distance (for example: telescopes and
binoculars) may pose an eye hazard.
Wavelength = 1.3/1.5 μm.
Maximum power = 30 mW.
*Caution - Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
*IEC is a registered trademark of the International Electrotechnical Commision.
© 2013 EMCORE Corporation | REV 2013.10
Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice.
+1 626-293-3400
satcom-sales@emcore.com
www.emcore.com
相关型号：
©2020 ICPDF网 联系我们和版权申明