HPS15Z-NNR-000 [EMERSON-NETWORKPOWER]
HPS10/12/15 Series; HPS10 / 12/ 15系列型号: | HPS15Z-NNR-000 |
厂家: | EMERSON NETWORK POWER |
描述: | HPS10/12/15 Series |
文件: | 总5页 (文件大小:1391K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
1000-6000 Watts
HPS10/12/15 Series
Electrical Specs
Input
Input voltage
Frequency
85-264 VAC*
47-440 Hz
Inrush current
Efficiency
Power factor
Turn-on time
40 A peak max.
85% typ @ full case load 230 VAC
0.99 typical meets EN61000-3-2
AC on 1.5 sec. typical, Inhibit /
Enable 100 ms typical
Special Features
EMI filter standard
Leakage current standard 2 mA max @ 264 VAC @ 60Hz
CISPR 22 EN55022 Level “B”
• Integrated OR-ing diode
(per module)
CISPR 22 EN55022 Level “B”
20 ms minimum
(independent of input VAC)
>5 ms early warning min. before
outputs lose regulation; Full cycle
ride thru (50 Hz)
Meets EN61000-3-2
Meets EN60950
• Remote Sense on Bulk output
• Overload protection on all outputs
• Active Inrush limiting
Radiated EMI
Holdup time
• PFC to 0.99 typical EN61000-3-2
• CISPR22, EN55022 Curve B
conducted/radiated EMI
AC OK
• EN61000 immunity standards
• Optional 48 W fan voltage (12 V or 24 V)
• Standard 5 V at 5 A standby voltage (3.3V option)
• No minimum load
Harmonic distortion
Isolation
* see modules table on the next page
• Overvoltage protection
• Input OK signal and indicator LED
• Inhibit/Enable
• Remote Margin/Voltage Programming
• Optional current monitor
Output
Margining
±5% of nominal
1%
Overall reg
• Optional AC Line discrimination
• Output Good signal and indicator LED
• Temp good signal and indicator LED
• Optional single wire digital temp monitor
• Optional module I2C interface
• Optional Rack µController
• Hot Plug
Ripple
1% of Vout Pk-Pk limited to 20 MHz
2% with 25% load step
To within 1% in <300 µsec
105-120% of rated output current
Protected for continuous short
circuit. Recovery is automatic upon
removal of short
Dynamic response
Recovery time
Overcurrent protection
Short circuit protection
• N+1 Redundant Standard
Overvoltage protection
105-120% . Recycle AC input voltage
to reset OVP circuit
• Optional fan fail signal
• Module present signal
Reverse voltage
protection
• Optional short circut latch
100% of rated output current
Thermal protection
Main and Aux disabled when internal
Environmental & Safety
Operating temperature: -10°C to +50°C ambient,
derate output @ 2.5% per degree from 50°C to 70°C
Shock/Vibration: Mil-Hdbk 810E
temp exceeds safe operating range.
Remote sense
Single wire parallel
Up to 0.5 V total drop
Current share to within 10% of total
rated current
±5% of nominal
Not required
5 VDC @5A max. present whenever
AC input is applied (3.3 V @ 5A
optional)
DC OK
Minimum load
Standby voltage
Humidity: 95% non-condensing
Storage temperature: -40°C to +85°C
Temperature coefficient: 0.02% per °C
Cooling: Internal DC fan
MTBF (Calculated): 200 KHrs; 25°C, 200 VAC input,
nominal O/P voltage, full load
Global Inhibit/Enable
Logic “0” standard logic “1” optional
Safety:
rd
UL / CSA UL60950 3 Ed and CSA C22.2 60950
TUV
CB
EN60950
Certificate and report
Mark
CE
152
Technical Support: (888) 41-ASTEC or (407) 241-2752
Americas: (760) 930-4600 Europe (UK) 44 (1384) 842-211 Asia (HK) 852-2437-9662
rev 08.25.04
ASIA
EUROPE
AMERICAS
Units 2111-2116, Level 21
Tower1, Metroplaza
223, Hing Fong Road
Fwai Fong, New Territories
Hong Kong
Telephone: 852-2437-9662
Facsimile: 852-2402-4426
Astec House, Waterfront Business Park
Merry Hill, Dudley
West Midlands, DY5 1LX, UK
Telephone: 44 (1384) 842-211
Facsimile: 44 (1384) 843-355
5810 Van Allen Way
Carlsbad, CA 92008
Telephone: 760-930-4600
Facsimile: 760-930-0698
I monitor
N = None
A = Current monitor
Watts
Input
1000
1250
1500
Power
Redundancy
N = None
10 = 1000 W
12 = 1250 W
15 = 1500 W
R = Or-ing diode
voltage
85-264 90-264 180-264
HPS10 HPS12 HPS15
Special Options
& Modifications
Module ID
Code
Contact Astec.
Volts
Output Output Output
Amps Amps Amps
-
-
-
Q
R
S
W
X
Y
24.0
28.0
30.0
48.0
54.0
60.0
41.7
35.7
33.3
20.8
18.5
16.7
52.1
44.6
41.7
26.0
23.1
20.8
62.5
53.6
50.0
31.3
27.8
25.0
XXX
HPS
Output Voltage
Q = 24 V
R = 28 V
S = 30 V
W = 48 V
Auxiliary Fan
Voltage
N = None
3 = 12 V @ 4 A
5 = 24 V @ 2 A
X = 54 V
Y = 60 V
Z = Consult factory
Standard Options
000 = No options
001 = 3.3 Standby
002 = Short circuit latch-off
004 = Enable “0”
008 = (Inhibit/enable), DC OK “1”
016 = Fan fail signal (optional)
032 = I2C interface
064 = AC line descriminator
128 = Temp OK “0”
Module
Code
Max. Size
(H x W x L)
Max. Module Max. Number Unit
Power
per Rack
Weight (lbs)
HPS10
HPS12
HPS15
5.04" x 3.83" x 12.5"
5.04" x 3.83" x 12.5"
5.04" x 3.83" x 12.5"
1000 W
1250 W
1500 W
4
4
4
10.5
10.5
10.5
256 = Module present “0”
Note: for combinations of options simply
add option codes together.
Size
Watts
Input
voltage
4000
5000
6000
Special Options
& Modifications
Contact Astec.
3 = 3U
85-264
100-264 180-264
Module Used
Rack ID
HPS10
HPR3
HPS12
HPR3
HPS15
HPR3
-
-
XXX
HPR
Output Output Output
Code
Q
Volts
Amps
166.7
142.9
133.3
83.3
Amps
208.3
178.6
166.7
104.2
92.6
Amps
250.0
214.3
200.0
125.0
111.1
100.0
24.0
28.0
30.0
48.0
54.0
60.0
Standard Options
R
00 = No options
S
01 = computer option
W
X
74.1
66.7
Y
83.3
HPR3 Module Blank Panel:
Astec P/N 73-536-026
HPR3 Logic Blank Panel:
Astec P/N 73-536-027
System
Code
Max. Size
(H x W x L)
Max. System
Power
Module
Distribution
Standard
Size
Unit
Weight
Notes:
1. Specifications subject to change without notice
2. All dimentions are in inches (mm), toleance is ± .02”
3. Specifications are at factory settings
4. Warranty: 1 Yr
HPR3
5.22" x 19.0" x 14.0"
6000 W (4 ea) HPS10/12/15 3U
16.4 lbs
5. For combinations of options simply add option codes
together.
www.astecpower.com
153
HPS Series
DRAWINGS
A: AC Input Connector
Positronics PLB3W3M1060
AC Pin: MC612N-228.2
Ground Pin: MC612N
HPS 10/12/15 Module
AC Input Pinouts
A
J1-L
J1-N
J1-G
LINE
NEUTRAL
GROUND
Mating Connector:
Positronics PLB3W3FXXXX
B: DC Output Connector
Positronics PCIH38M400A1
Mating Connector
Positronics PCIH38FXXXX or
Elcon 226-0005-00100
DC Output Pinouts
P1-1
P1-2
P1-3
P1-4
P1-5
P1-6
P1-7
P1-8
P1-9
V OUT
V OUT
V OUT
V OUT
B
V OUT
V OUT
V OUT RTN
V OUT RTN
V OUT RTN
P1-10 V OUT RTN
P1-11 V OUT RTN
P1-12 V OUT RTN
P1-13 CHASSIS GND
P1-14 CHASSIS GND
P1-15 5VDC
P1-16 5VDC
P1-17 5VDC RTN
P1-18 5VDC RTN
P1-19 DATA
P1-20 DATA GND
P1-21 V OUT SENSE
P1-22 V OUT SENSE RTN
P1-23 MARGIN PROGRAM
P1-24 MARGIN HI
P1-25 SWP
P1-26 ISO ENA/DCOK/
TEMP OK/FAN FAIL RTN
P1-27 ISO DCOK
P1-28 ISO EN/INH
P1-29 ISO TEMP OK
P1-30 OPAMP/SYNC/FAN FAIL SIGNAL
P1-31 I MONITOR
P1-32 I MONITOR RTN
P1-33 N/C
P1-34 ACOK COLLECTOR
P1-35 ACOK EMITTER
P1-36 V AUX RTN
P1-37 V AUX
P1-38 V ANODE (MAIN O/P)
154
Technical Support: (888) 41-ASTEC or (407) 241-2752
Americas: (760) 930-4600 Europe (UK) 44 (1384) 842-211 Asia (HK) 852-2437-9662
ASIA
EUROPE
AMERICAS
Units 2111-2116, Level 21
Tower1, Metroplaza
223, Hing Fong Road
Fwai Fong, New Territories
Hong Kong
Telephone: 852-2437-9662
Facsimile: 852-2402-4426
Astec House, Waterfront Business Park
Merry Hill, Dudley
West Midlands, DY5 1LX, UK
Telephone: 44 (1384) 842-211
Facsimile: 44 (1384) 843-355
5810 Van Allen Way
Carlsbad, CA 92008
Telephone: 760-930-4600
Facsimile: 760-930-0698
HPR3 Rack
AC Cord: Qualtek Electronics or
Equivalent
Part Number: 227003-01
AWG: 12
Rating(A): 20A
Cord Type: SJT
NEMA Plug Type: 5-20P
IEC Connector Type: C-19
J20
J21
J22
www.astecpower.com
155
HPR3 -00 Pin Assignments
J21 Control Connector for PS1 & PS2 (Slot 1 & 2)
J20 Control Connector for PS3 & PS4 (Slot 3 & 4)
PS1
PS3
Pin No. Function
Pin No. Function
J21-1
J21-2
J21-3
J21-4
J21-5
J21-6
J21-7
J21-8
J21-9
+V Anode ( module present )
AC OK collector
J20-1
J20-2
J20-3
J20-4
J20-5
J20-6
J20-7
J20-8
J20-9
+V Anode ( module present )
AC OK collector
I monitor return
I monitor return
Op amp / Sync / Fan Fail Signal
Enable / Inhibit (isolated)
Enable / DC OK / Temp OK / Fan Fail RTN
Margin Program
+ Sense Vout
N/C
Op amp / Sync / Fan Fail Signal
Enable / Inhibit (isolated)
Enable / DC OK/ Temp OK / Fan Fail RTN
Margin Program
+ Sense Vout
N/C
J21-20 AC ok emitter
J21-21 Ext bias
J20-20 AC ok emitter
J20-21 Ext bias
J21-22 I monitor
J21-23 Temp OK
J21-24 DC OK (isolated)
J21-25 Margin high
J21-26 - Sense Vout
J21-27 N/C
J20-22 I monitor
J20-23 Temp OK
J20-24 DC OK (isolated)
J20-25 Margin high
J20-26 - Sense Vout
J20-27 N/C
J21-28 N/C
J20-28 N/C
PS4
PS2
Pin No. Function
Pin No. Function
J20-10 +V anode ( module present )
J20-11 AC OK collector
J20-12 I monitor return
J20-13 Op amp / Sync / Fan Fail Signal
J20-14 Enable / Inhibit (isolated)
J20-15 Enable / DC OK / Temp OK / Fan Fail RTN
J20-16 Margin Program
J20-17 + Sense Vout
J20-18 N/C
J21-10 +V Anode ( module present )
J21-11 AC OK collector
J21-12 I monitor return
J21-13 Op amp / Sync / Fan Fail Signal
J21-14 Enable / Inhibit (isolated)
J21-15 Enable / DC OK / Temp OK / Fan Fail RTN
J21-16 Margin Program
J21-17 + Sense Vout
J21-18 N/C
J20-19 N/C
J21-19 N/C
J20-29 AC OK emitter
J20-30 Ext bias
J20-31 I monitor
J20-32 Temp OK
J21-29 AC OK emitter
J21-30 Ext bias
J21-31 I monitor
J21-32 Temp OK
J20-33 DC OK (isolated)
J20-34 Margin high
J20-35 - Sense Vout
J20-36 N/C
J21-33 DC OK (isolated)
J21-34 Margin high
J21-35 - Sense Vout
J21-36 N/C
J20-37 N/C
J21-37 N/C
J22 Sense Connector
Pin No. Function
J22-1
J22-2
J22-3
J22-4
J22-5
J22-6
J22-7
J22-8
J22-9
-Sense Vout
N/C
Enable / Inhibit gnd
N/C
N/C
SWP
+Sense Vout
Enable / Inhibit
N/C
156
Technical Support: (888) 41-ASTEC or (407) 241-2752
Americas: (760) 930-4600
Europe (UK) 44 (1384) 842-211
Asia (HK) 852-2437-9662
相关型号:
©2020 ICPDF网 联系我们和版权申明