EM6156 [EMMICRO]
5V 120mA Automotive LDO Regulator with Watchdog; 5V 120毫安汽车LDO稳压器，带有看门狗
| 型号： | EM6156 |
| 厂家： | 
EM MICROELECTRONIC - MARIN SA |
| 描述： | 5V 120mA Automotive LDO Regulator with Watchdog |
| 文件： | 总11页 (文件大小：482K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
R
EM MICROELECTRONIC - MARIN SA
EM6156
5V 120mA Automotive LDO Regulator with Watchdog
Description
Features
The EM6156 offers a high level of integration by combining
voltage regulation, voltage monitoring and software
monitoring using a watchdog.
-40°C to +125°C temperature range
Highly accurate 5 V, 120 mA guaranteed output (actual
maximum current depends on power dissipation)
A comparator monitors the voltage applied at the VIN input
comparing it with an internal voltage reference VREF. The
power-on reset function is initialized after VIN reaches
VREF and takes the reset output inactive after a delay
TPOR. The reset output goes active low when the VIN
voltage is less than VREF. The RESET output is guaranteed
to be in a correct state for a regulated output voltage as low
as 1.2V. The watchdog function monitors software cycle
time and execution. If software clears the watchdog too
slowly (incorrect execution) it will cause the system to be
reset.
Output voltage tolerance <+/- 3%
Low dropout voltage, typically 250 mV at 100 mA
Unregulated DC input can withstand -42 V reverse
battery and +45 V power transients
Fully operational for unregulated DC input voltage up to
40 V and regulated output voltage down to 3.5 V
No reverse output current
Very low temperature coefficient for the regulated
output
Current limiting
In EM6156, the voltage regulator has a low dropout voltage
and
a low quiescent current. The quiescent current
Four threshold voltages (2.9V, 3.0V, 4.4V, 4.6V)
increases only slightly in dropout prolonging battery life.
Built-in protection includes a positive transient absorber for
up to 45 V (load dump) and the ability to survive an
unregulated input voltage of -42 V (reverse battery). The
input may be connected to ground or to a reverse voltage
without reverse current flowing from the output to the input.
Several timeout reset periods (1.6ms, 25ms, 200ms,
1600ms)
Several watchdog timeout periods (6.2ms, 102ms, 1,6s,
25,6s)
Push pull or Open-drain active-low RESET output
Reset output guaranteed for regulated output voltage
down to 1.2 V
Qualified according to AEC-Q100
Typical Operating Configuration
Green SO8 Exposed Pad Power Package (RoHS
compliant)
Applications
Automotive systems
Industrial
Home security systems
Fig. 1
1
www.emmicroelectronic.com
Copyright © 2007, EM Microelectronic-Marin SA
06/07 – rev.A
R
EM6156
Block Diagram
Fig. 2
Pin Assignment
Description
SO8
Exposed
Pad
Name
Function
1
VDD
Watchdog power supply
2
Watchdog timer clear input signal
WDI
VSS
3
4
5
6
7
Ground terminal
VIN
Voltage regulator input
Not connected
NC
VOUT
RESET
Voltage regulator output
RESET Output (Push-pull)
8
RESET
RESET Output
Exposed pad Can be connected to VSS or left floating
Table 1
2
www.emmicroelectronic.com
Copyright © 2007, EM Microelectronic-Marin SA
06/07 – rev.A
R
EM6156
Ordering Information
Standard Versions
Part Number
Threshold Timeout Watchdog
Reset
Output
Package
Delivery Form
Tape & Reel, 2500 pcs
Package
Marking
Reset
Reset
Timeout
EM6156LXES8B-4.4+
4.4V
200ms
1.6s
Active Low
Push Pull
ExPadSO8
TBD
Note: the "+" symbol at the end of the part number means that this product is RoHS compliant (green).
Sample stock is generally held on standard versions only. Please contact factory for other versions not shown here and for
availability of non standard versions.
3
www.emmicroelectronic.com
Copyright © 2007, EM Microelectronic-Marin SA
06/07 – rev.A
R
EM6156
Absolute Maximum Ratings
See the notes related to Table 2. Special care must be
taken in disturbed environments (automotive, proximity of
motors and relays, etc).
Parameter
Symbol
VIN
Conditions
-0.3V to +40V
Continuous voltage at VIN to VSS
Transients on VIN for t < 100ms
and duty cycle 1%
Max. voltage at any signal pin
Min. voltage at any signal pin
Reverse supply voltage on VIN
Storage temperature
VTRANS
Up to +45V
Handling Procedures
VMAX VOUTPUT + 0.3V
VMIN
VREV
This device has built-in protection against high static
voltages or electric fields; however, anti-static precautions
must be taken as for any other CMOS component. Unless
otherwise specified, proper operation can only occur when
all terminal voltages are kept within the voltage range.
Unused inputs must always be tied to a defined logic
voltage level.
VSS – 0.3V
-42V
TSTO -65 to °150°C
ESD According to MIL-STD-883
method 3015.7
VSmax 2000V
Table 2
Stresses above these listed maximum ratings may cause
permanent damages to the device. Exposure beyond
specified operating conditions may affect device reliability or
cause malfunction.
Operating Conditions
Parameter
Symbol Min
Max
+150
40
Unit
°C
V
Operating junction temperature
VIN voltage (Note 1)
VOUT voltage (Note 1,2)
Tj
-40
4.0
3.5
VINPUT
VOUTPUT
5.5
V
Decoupling Methods
VOUTPUT
1.2
V
RESET guaranteed (Note 3)
The input capacitor is necessary to compensate the line
influences. A resistor of approx. 1Ω connected in series
with the input capacitor may be used to damp the oscillation
of the input capacitor and input inductance. The ESR value
of the capacitor plays a major role regarding the efficiency of
the decoupling. It is recommended also to connect a
ceramic capacitor (100nF) directly at the IC's pins. In
general the user must assure that pulses on the input line
have slew rates lower than 1V/µs. On the output side, the
capacitor is necessary for the stability of the regulation
circuit. The stability is guaranteed for values of 10 µF or
greater. It is especially important to choose a capacitor with
a low ESR value. Tantalum capacitors are recommended.
VOUT output current (Note 4)
Comparator input voltage
Package thermal resistance
from junction to ambient: Exp.
Pad SO8 150 MILS (Note 5)
IOUTPUT
VIN
120
0
mA
V
VOUT
90
Rth(j-a)
30
°C/W
Table 3
Note 1:
Note 2:
Full operation guaranteed. To achieve the load regulation specified in Table 3, a 10 µF capacitor or greater is required on the
VIN, see Fig. 1b. The 10 µF must have an effective resistance ≤ 4 Ω and a resonant frequency above 500 kHz.
A 10µF load capacitor and a 100 nF decoupling capacitor are required o the regulator output for stability. The 10 µF must have
an effective series resistance of < 4 Ω and a resonant frequency above 500 kHz.
Note 3:
Note 4:
For open drain output type, RESET must be pulled up externally to VOUT even if it is unused.
The output current will not apply to the full range of input voltage. Power dissipation that would require the EM6156 to work
above the maximum junction temperature (+150 °C) must be avoided.
Note 5:
The thermal resistance specified assumes the package is soldered to a PCB. A typical value of 51 °C/W has been obtained
with a dual layer board, with the slug soldered to the heat-sink area of the PCB.
4
www.emmicroelectronic.com
Copyright © 2007, EM Microelectronic-Marin SA
06/07 – rev.A
R
EM6156
Electrical Characteristics
VIN = 13.5V, COUT = 10µF + 100nF, CIN = 2 µF, VDD connected to VOUT; TA = -40 to +125 °C (Note 1), unless otherwise
specified.
Parameter
Symbol
Conditions
Min
Typ
Max
Unit
Low drop Output Regulator
Supply current (Note 6)
Supply current
ISS
ISS
VOUTPUT
VLINE
VL
IL = 1 mA
IL = 100 mA
5 mA ≤ IL ≤ 100 mA
6 V ≤ VIN ≤ 100 mA, IL = 5 mA
5 mA ≤ IL ≤ 100 mA, VIN = 6V
IL = 100 mA
412
15
5.10
30
40
500
µA
mA
V
mV
mV
mV
mA
9
5
15
Output voltage
4.9
Line regulation (Note 7)
Load regulation (Note 7)
Dropout voltage (Note 8)
Current limit
VDROPOUT
ILmax
250
160
Output tied to VSS, VIN = 6V
120
Reset
Threshold hysteresis
VHYS
tPOR
TA = +25°C
-
2.1%●VTH
200
1.56
25
1600
-
V
EM6156 C-G-L-Q
EM6156 A-E-J-N
EM6156 B-F-K-P
EM6156 D-H-M-R
160
0.7
20
240
3.8
30
VDD from 0V to
VTH(typ)+15%
TA = +25°C
(Note 2 & Note 4)
Reset timeout period
ms
1280
1920
Propagation delay time
VDD drops from VTH(typ) +0.2V to
TH(typ)-0.2V (Note 2). TA = +25°C
tP
2
70
255
µs
V
VDD to RESET (RESET)
V
delay
VDD > 1V
VDD > 2.5V
VDD > 5V
VDD > 2.5V
VDD > 5V
IOL = 100µA
IOL = 1.5mA
IOL = 3mA
IOL = 1.5mA
IOL = 3mA
IOL = 100µA
IOL = -30µA
IOL = -1.5mA
IOL = -3mA
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0.3
0.3
0.35
0.3
0.35
0.3
-
Open-drain RESET output
voltage
VOL
VOL
Push-pull RESET / RESET
output voltage
V
VDD > 1V
VDD > 1.1V
VDD > 2.5V
VDD > 5V
0.8
2
4
-
VOH
V
-
-
Output leakage current
ILEAK
Only for EM6156_Y (open-drain)
+25°C
0.5
µA
2.886
2.784
2.731
3.034
2.926
2.871
4.334
4.180
4.101
4.561
4.399
4.315
2.974
3.091
3.103
3.126
3.249
3.262
4.466
4.642
4.660
4.699
4.885
4.903
EM6156-2.9
EM6156-3.1
EM6156-4.4
EM6156-4.6
-40°C to +85°C
-40°C to +125°C
+25°C
-40°C to +85°C
-40°C to +125°C
+25°C
-40°C to +85°C
-40°C to +125°C
+25°C
-40°C to +85°C
-40°C to +125°C
2.93
3.08
4.40
4.63
Threshold voltage (Note 3)
VTH
V
Watchdog Input (WDI)
WDI Input low
WDI Input high
VWDI low
VWDI high
tWP
-
0.7●VDD
1
1280
5
-
-
-
0.3●VDD
V
V
µs
TA = +25°C
(Note 5)
-
Pulse width at WDI
-
1920
7.5
120
30720
-
EM6156 J-K-L-M
EM6156 A-B-C-D
EM6156 E-F-G-H
1600
6.25
100
25600
18
Watchdog timeout period
tWD
ms
80
EM6156 N-P-Q-R 20480
High-level input current
Low-level input current
IIH
IIL
WDI connected to VDD, TA = +25°C
WDI connected to VSS, TA = +25°C
-
-
µA
µA
8.3
-
Table 4
Note 1:
Production tested at +25°C only. Over temperature limits are guaranteed by design, not production tested.
WDI and RESET open.
Note 2:
Note 3:
Note 4:
Note 5:
Note 6:
Note 7:
Note 8:
Threshold voltage is specified for VDD falling.
Standard version for tPOR is 200ms (typ). Other option (1.6ms, 25ms, 1600ms) are available by mask option
Standard version for tWD is 1600ms (typ). Other option (6.2ms, 102ms, 25.6s) are available by mask option
If INPUT is connected to VSS, no reverse current will flow from the OUTPUT to the INPUT.
Regulation is measured at constant junction temperature using pulse testing with a low duty cycle.
The dropout voltage is defined as the INPUT to OUTPUT differential, measured with the input voltage equal to 5.0 V.
5
www.emmicroelectronic.com
Copyright © 2007, EM Microelectronic-Marin SA
06/07 – rev.A
R
EM6156
Timing Waveforms
Watchdog Timeout Period
tSEN
VDD
VHYS
VTH
Overdrive
0.9V
t
logic "1"
RESET
tPOR
tMD
tP
logic "0"
t
logic "1"
RESET
tPOR
logic "0"
t
Fig. 3
logic "1"
WDI
tWP
tWD
tWD
logic "0"
t
logic "1"
RESET
logic "0"
t
logic "1"
RESET
tPOR
logic "0"
t
Fig. 4
Note 9: tSEN = Maximum Transient Duration. Please refer to figure on the next page.
Note 10: Overdrive = VTH -VDD. Please refer to figure on the next page.
6
www.emmicroelectronic.com
Copyright © 2007, EM Microelectronic-Marin SA
06/07 – rev.A
R
EM6156
Typical Operating Characteristics
(Typical values are at TA=+25°C unless otherwise noted. WDI,
and RESET open.)
RESET
9
6%
4%
8
VDD 5 . 0 V
7
2%
6
5
0%
VDD 3 . 3 V
[ uA ]
4
-2%
-4%
-6%
3
VDD 1 . 5 V
2
1
0
-50 -25
0
25
[ °C ]
50
75 100 125
-50 -25
0
25
[ °C ]
50
75 100 125
Fig. 5
Fig. 6
IDD vs. Temperature
Threshold Voltage Variation vs. Temperature
(normalized)
160%
140%
120%
100%
80%
160%
tPOR (°C)
tPOR (25°C)
tWD (°C)
140%
120%
100%
80%
tWD (25°C)
60%
60%
-50 -25
0
25
50
75 100 125
-50 -25
0
25
50
75
100 125
[ °C ]
[ °C ]
Fig. 8
Watchdog Timeout Period tWD vs. Temperature
(normalized with respect to tWD 25°C
Fig. 7
Reset Timeout Period tPOR vs. Temperature
(normalized with respect to tPOR 25°C
)
)
120
100
80
120
Reset occurs above
this line
100
80
[ us ]
60
[ us ]
60
40
20
0
40
20
0
-50 -25
0
25
50
[ °C ]
75
100 125
1
10
100
1000
[ mV ]
Fig. 10
Fig. 9
Maximum Transient Duration tSEN vs.
Overdrive VTH-VD
Propagation Time tPHL vs. Temperature
7
www.emmicroelectronic.com
Copyright © 2007, EM Microelectronic-Marin SA
06/07 – rev.A
R
EM6156
Typical Operating Characteristics
(Typical values are at TA = +25°C unless otherwise noted. WDI,
and RESET open)
RESET
250
225
200
[ ns ]
175
150
125
100
-50 -25
0
25 50 75 100 125
[ °C ]
Fig. 11
Watchdog Input Pulse Width tWP vs. Temperature
Functional Description
VDD
MR
WDI
High Impedance
RESET
t < tWD
t > tWD
tPOR
tPOR
tPOR
Fig. 12
flow from the VOUT to the VIN when the VIN equals VSS.
This feature is important for systems which need to
implement (with capacitance) a minimum power supply
hold-up time in the event of power failure. To achieve good
load regulation a 22 μF capacitor (or greater) is needed on
the VIN (see Fig. 17). Tantalum or aluminium electrolytic
are adequate for the 22 μF capacitor; film types will work
but are relatively expensive. Many aluminium electrolytic
have electrolytes that freeze at about –30°C, so tantalums
are recommended for operation below –25°C. The
important parameters of the 22 μF capacitor are an
effective series resistance of lower than 4Ω and a resonant
frequency above 500 kHz.
VOUT Monitoring
A microprocessor (μP) reset input starts the microcontroller
in a known state. The EM6156 microcontroller supervisory
circuits assert a reset to prevent code-execution errors
during power-up, power down, and brownout conditions.
is guaranteed to be a logic low for VDD down to
RESET
0.9V. Once VDD exceeds the reset threshold, an internal
timer keeps low for the specified reset timeout
RESET
period (tPOR); after this interval,
returns high.
RESET
If a brownout condition occurs (VDD dips below the reset
threshold), goes low. Each time is asserted
RESET
RESET
it stays low for the reset timeout period. Any time VDD
goes below the reset threshold the internal timer restarts.
A output 10 μF capacitor (or greater) and a 100 nF
capacitor are required on the output to prevent oscillations
due to instability. The specification of this 10 μF capacitor
is as per the 22 μF capacitor on the input (see previous
paragraph).
is the inverse of RESET.
RESET
Voltage Regulator
The EM6156 has a 5 V, 150 mA, low dropout voltage
regulator. The low supply current makes the EM6156
particularly suitable for automotive systems which remain
continuously powered. The input voltage range is 2.3 V to
40 V for operation and the input protection includes both
reverse battery (42 V below ground) and load dump
(positive transients up to 45 V). There is no reverse current
The EM6156 will remain stable and in regulation with no
external load and the dropout voltage is typically constant
as the input voltage fall below its minimum level (see Table
2). These features are especially important in CMOS RAM
keep-alive applications.
8
www.emmicroelectronic.com
Copyright © 2007, EM Microelectronic-Marin SA
06/07 – rev.A
R
EM6156
Power Dissipation
VDD
WDI
GND
Care must be taken not to exceed the maximum junction
temperature (+125°C). The power dissipation within the
EM6156 is given by the formula:
Pullup
1/16 tWD
PTOTAL = (VINPUT – VOUTPUT) × IOUTPUT + (VINPUT) × ISS
The maximum continuous power dissipation at a given
temperature can be calculated using the formula:
PMAX = ( 150°C – TA) / Rth(j-a)
where Rth(j-a) is the thermal resistance from the junction to
the ambient and is specified in Table 2. Note that Rth(j-a)
given in Table 2 assumes that the package is soldered to a
PCB. The above formula for maximum power dissipation
assumes a constant load (i.e. >100 s). The transient
thermal resistance for a single pulse is much lower than the
continuous value.
Transition
Detector
Watchdog Logic
+ Timer
15/16 tWD
Pulldown
Fig. 14
WDI Input Stage Block Schematic
Watchdog Description
15.0
If the watchdog timer has not been cleared within tWD (1.6s
typ.), reset asserts. The internal 1.6s timer is cleared by
either a reset pulse or by toggling WDI. While reset is
asserted, the timer remains cleared and does not count. As
soon as reset is released, the timer starts counting. If the
microcontroller I/O connected to WDI is put in a high
impedance condition, the circuit will detect this condition as
a microcontroller in sleep mode and prevent its watchdog
from timing out. To monitor a high impedance or a three
state condition on WDI, the watchdog input is internally
driven low during the first 15/16 of the watchdog timeout
period and high for the last 1/16 of the watchdog timeout
period.
12.0
9.0
[ uA ]
6.0
3.0
0.0
-50 -25
0
25
50
75 100 125
[ °C ]
VDD
Fig. 15
RESET
WDI Input Current Low-level IIL vs. Temperature
(VDD=5.5V)
WDI Pullup OFF
ON
OFF
ON
WDI Pulldown ON
15/16 tWD
tWD
OFF
tPOR
1/16 tWD
25.0
20.0
Fig. 13
WDI Input Timing Diagram
15.0
[ uA ]
When WDI is left unconnected, this internal driver clears
the 1.6s timer every 1.5s. When WDI is three-stated or
unconnected, the maximum allowable leakage current is
0.5µA.
10.0
5.0
To minimized the overall system power consumption and
therefore for a minimum watchdog input current leave WDI
low for the majority of the watchdog timeout period, pulsing
it low-high-low once within the first 15/16 of the watchdog
timeout period to reset the watchdog timer. If WDI is
externally driven high for the majority of the timeout period,
up to 35µA can flow into WDI. Meanwhile when the
microcontroller is not in sleep mode, the output of the
microcontroller which drives WDI has to be strong enough
to fight the 35µA.
0.0
-50 -25
0
25 50 75 100 125
[ °C ]
Fig. 16
WDI Input Current High-Level IIH vs. Temperature
(VDD=5.5V)
9
www.emmicroelectronic.com
Copyright © 2007, EM Microelectronic-Marin SA
06/07 – rev.A
R
EM6156
Typical Application
Unregulated
Voltage
VIN
Regulated Voltage (5V)
Address decoder
VOUT
VDD
COUT
+
EM6156
100nF 10uF
22uF
+
WDI
Microprocessor
RES
RESET
VSS
Motor
controls
GND
Fig. 17
The important parameters of the 10µF capacitor are an effective series resistance lower than 4Ω and a resonant frequency
above 500 kHz.
Typical maximum output current versus VIN (to be confirmed after qualification)
200
Esposed Pad SO8 Package
Bottom slug soldered to PCB
180
160
140
120
100
80
TA=25°C
TA=85°C
60
40
20
0
5
10
15
20
25
30
35
40
INPUT Voltage [V]
10
www.emmicroelectronic.com
Copyright © 2007, EM Microelectronic-Marin SA
06/07 – rev.A
R
EM6156
Package Information
EM Microelectronic-Marin SA (EM) makes no warranty for the use of its products, other than those expressly contained in the Company's
standard warranty which is detailed in EM's General Terms of Sale located on the Company's web site. EM assumes no responsibility for any
errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice,
and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of EM are
granted in connection with the sale of EM products, expressly or by implications. EM's products are not authorized for use as components in
life support devices or systems.
11
www.emmicroelectronic.com
Copyright © 2007, EM Microelectronic-Marin SA
06/07 – rev.A
相关型号：
©2020 ICPDF网 联系我们和版权申明