B32660-A8102-J010 [EPCOS]

CAPACITOR, METALLIZED FILM, POLYPROPYLENE, 1000V, 0.001uF, THROUGH HOLE MOUNT, AXIAL LEADED;


型号：	B32660-A8102-J010
厂家：	EPCOS
描述：	CAPACITOR, METALLIZED FILM, POLYPROPYLENE, 1000V, 0.001uF, THROUGH HOLE MOUNT, AXIAL LEADED 电容器
文件：	总4页 (文件大小：52K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

Metallized Polypropylene Film Capacitors (MKP)

Uncoated (Silver Caps)

B 32 660

MKP stacked-film capacitors

Extremely small dimensions

Outstanding contact reliability

Cut

surfaces

Construction

● Dielectric: polypropylene

● Stacked-film technology

● Uncoated

Features

Dimensions in mm

● Special dimensions available upon request

● High pulse strength

● High ac-loads

Lead spacing Diameter d

Type

B 32 660

± 0,4

● Small dimensions

7,5

0,5

Typical applications

● Lamp ballast circuits

● Snubbering of semi-conductors

Terminals

● Parallel wire leads, tinned (for C = 2,2 … 6,8 nF)

● Crimped leads, tinned (for C ≤ 1,5 nF)

Marking

Rated capacitance (coded),

rated dc voltage

Delivery mode

Bulk (untaped)

Taped (Ammo pack or reel)

For notes on taping, refer to page 279.

Notes on mounting

When mounting these capacitors, take into account creepage distances and clearances to adjacent

live parts. The insulating strength of the cut surfaces to other live parts of the circuit is 1,5 times the

capacitors rated dc voltage, but is always at least 300 Vdc.

Capacitors with 7,5 mm lead spacing are only suitable for use with single-clad printed circuit boards.

Siemens Matsushita Components

131

B 32 660

MKP

7,5

Ordering codes and packing units

Maximum

Ordering code

Packing units (pcs)

dimensions

b × h × l (mm)

rms

Ammo

pack

2800

2200

2000

2700

2100

1800

1600

1700

1600

−

Reel

Untaped

f ≤ 1 kHz)

1000 Vdc 0,15 nF

(450 Vac)

3,1 × 6,9 × 9,0

3,9 × 7,3 × 9,0

4,4 × 9,1 × 9,0

3,2 × 6,5 × 9,0

4,0 × 7,2 × 9,0

4,9 × 8,1 × 9,0

5,5 × 10,3 × 9,0

5,4 × 7,6 × 9,0

5,4 × 10,0 × 9,0

5,4 × 14,8 × 9,0

8,2 × 10,9 × 9,0

9,2 × 11,2 × 9,0

B32660-A8151-K

B32660-A8221-+

2200

1700

1600

2200

1700

1400

1300

−

1200

900

600

1250

850

600

400

600

400

300

200

***

0,22 nF

0,33 nF

***

B32660-A8331-+

B32660-A8471-+

B32660-A8681-+

B32660-A8102-+

B32660-A8152-+

B32660-A8222-+

B32660-A8332-+

B32660-A8472-+

B32660-A8562-+

B32660-A8682-+

1000 Vdc 0,47 nF

(600 Vac)

0,68 nF

1,0 nF

1,5 nF

2,2 nF

3,3 nF

4,7 nF

5,6 nF

6,8 nF

−

Capacitance tolerance: ± 10 % =ˆ K ( ± 5 % =ˆ J upon request)

Special dimensions available upon request. For corresponding design rules, refer to page 238.

Capacitors with C ≤ 1,5 nF are only available with crimped leads.

Crimping increases the mounting height by approx. 4 mm

(also refer to “Taping and Packing”, page 279).

1) Replace the + by the code letter for the required capacitance tolerance.

Replace the *** by the code number for the required packing form:

– For crimped leads (0,15 to 1,5 nF): Ammo pack = 249, reel = 149, untaped = 010

– For straight leads (2,2 to 6,8 nF): Ammo pack = 289, reel = 189

– The ordering code for untaped components ends after the tolerance code letter.

2) Capacitance tolerance: ± 10 % =ˆ K

132

Siemens Matsushita Components

B 32 660

MKP

7,5

Technical data

Climatic category

55/100/56

in accordance with IEC 68-1

Lower category temperature T

Upper category temperature T

− 55 °C

+ 100 °C

min

max

Damp heat test

56 days/40 °C/93% relative humidity

Limit values after damp

heat test

Capacitance change |∆C/C|

Dissipation factor change ∆ tan δ

≤ 3%

−3

≤ 0,5 10 (at 1 kHz)

≤ 1,0 10 (at 10 kHz)

−3

Insulation resistance R

≥ 50 % of minimum

or time constant τ = C

as-delivered values

Reliability:

Reference conditions

Failure rate

0,5 V ; 40 °C

1 10 /h = 2 fit

−9

For a conversion table for other operating conditions and tem-

peratures, refer to page 276.

Service life

200 000 h

Failure criteria:

Total failure

Short circuit or open circuit

Failure due to variation

of parameters

Capacitance change |∆C/C|

Dissipation factor tan δ

> 10 %

> 4 upper limit value

Insulation resistance R

< 1500 MΩ(C ≤ 0,33 µF)

or time constant τ = C

< 500 s

(C > 0,33 µF)

DC test voltage

1,4 V , 2 s

Category voltage V

T ≤ 85 °C: V = 1,0

or 1,0

or 0,7

rms

Operation with dc voltage or

ac voltage V up to 1 kHz

T = 100 °C: V = 0,7

rms

−3

Dissipation factor tan δ (in 10

at 20 °C

)

at 100 kHz: 4 10

(upper limit values)

Insulation resistance R

100 GΩ

or time constant τ = C

at 20 °C, rel. humidity ≤ 65 %

(minimum as-delivered values)

Maximum permissible voltage

change per unit of time for

non-sinusoidal voltages

(pulse, sawtooth)

Max. rate of voltage rise Pulse characteristic

/τ (for V = V ) k in (for V ≤ V )

7000 V/µs

14 000 000 V /µs

0,15 ...1,0 nF

1,5 ... 6,8 nF 5000 V/µs

10 000 000 V /µs

Siemens Matsushita Components

133

B 32 660

MKP

7,5

Permissible ac voltage V

Lead spacing 7,5 mm

1000 Vdc/ 450 Vac

versus frequency f

rms

1000 Vdc/ 600 Vac

134

Siemens Matsushita Components