B59100-C920-A70 [EPCOS]

RESISTOR, TEMPERATURE DEPENDENT, PTC, 100000ohm, THROUGH HOLE MOUNT, RADIAL LEADED, ROHS COMPLIANT;


型号：	B59100-C920-A70
厂家：	EPCOS
描述：	RESISTOR, TEMPERATURE DEPENDENT, PTC, 100000ohm, THROUGH HOLE MOUNT, RADIAL LEADED, ROHS COMPLIANT 温度传感电阻器
文件：	总7页 (文件大小：281K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

PTC thermistors

Limit temperature sensors,

leaded disks, coated

Series/Type:

B59100

Date:

June 2008

information contained therein without EPCOS' prior express consent is prohibited.

Sensors

Limit temperature sensors, leaded disks, coated

C100

Applications

Limit temperature monitoring

Features

Tinned leads

Manufacturer's logo and type designation stamped on in white

Characteristics for nominal threshold temperatures of 90 to 150 °C conform with DIN 44081

RoHS compatible

Delivery mode

Cardboard strips (standard), cardboard tape reeled or in Ammo pack on request

Dimensional drawing

Dimensions in mm

General technical data

Max. operating voltage

Max. measuring voltage

Rated resistance

(T_A= 0 ... 40 °C)

(T_Aꢀ25 K ... T_NTT+ 23 K)

(V_PTC≤ 2.5 V)

V_max

V_meas,max

R_R

7.5

≤ 100¹⁾

VDC

Ω

Thermal threshold time

t_a

< 5

Operating temperature range (V ≤ V_meas,max

)

T_op

ꢀ40/ T_NTT+23

0/+40

°C

Operating temperature range (V = V_max

)

1) Exception: B59100C0920A070: R_R> 100 kΩ; B59100C0010A070: R_R> 5 kΩ; B59100C0050A070: R_R< 150 Ω

Please read Cautions and warnings and

Important notes at the end of this document.

Page 2 of 7

Sensors

Limit temperature sensors, leaded disks, coated

C100

Electrical specifications and ordering codes

T_NTT

Ordering code

(T_NTTꢀ ∆T)

(VPTC ≤ 2.5 V)

Ω

(T_NTT+ ∆T)

(VPTC ≤ 2.5 V)

Ω

(T_NTT+ 15 K)

(VPTC ≤ 7.5 V)

Ω

(T_NTT+ 23 K)

(VPTC ≤ 2.5 V)

Ω

°C

∆T = ±5 K

ꢀ20

≤ 2300

≤ 400

≤ 570

≤ 550

≥ 2300

≥ 400

≥ 570

≥ 10 k

≥ 4 k

≥ 10 k

B59100C0920A070

B59100C0010A070

B59100C0050A070

B59100C0060A070

B59100C0070A070

B59100C0080A070

B59100C0090A070

B59100C0100A070

B59100C0110A070

B59100C0120A070

B59100C0130A070

B59100C0140A070

B59100C0150A070

≥ 570

≥ 1330

≥ 4 k

100

110

120

130

140

150

Please read Cautions and warnings and

Important notes at the end of this document.

Page 3 of 7

Sensors

Limit temperature sensors, leaded disks, coated

C100

Characteristics (typical)

PTC resistance R_PTCversus PTC temperature T_PTC

(measured at low signal voltage)

Please read Cautions and warnings and

Important notes at the end of this document.

Page 4 of 7

Sensors

Limit temperature sensors, leaded disks, coated

C100

Cautions and warnings

General

EPCOS thermistors are designed for specific applications and should not be used for purposes

not identified in our specifications, application notes and data books unless otherwise agreed

with EPCOS during the design-in-phase.

Ensure suitability of thermistor through reliability testing during the design-in phase. The ther-

mistors should be evaluated taking into consideration worst-case conditions.

Storage

Store thermistors only in original packaging. Do not open the package before storage.

Storage conditions in original packaging: storage temperature ꢀ25 °C ... +45 °C, relative hu-

midity ≤75% annual mean, maximum 95%, dew precipitation is inadmissible.

Avoid contamination of thermistors surface during storage, handling and processing.

Avoid storage of thermistor in harmful environment with effect on function on long-term opera-

tion (examples given under operation precautions).

Use thermistor within 6 months after delivery.

Handling

PTCs must not be dropped. Chip-offs must not be caused during handling of PTCs.

Components must not be touched with bare hands. Gloves are recommended.

Avoid contamination of thermistor surface during handling.

Soldering (where applicable)

Use rosin-type flux or non-activated flux.

Insufficient preheating may cause ceramic cracks.

Rapid cooling by dipping in solvent is not recommended.

Complete removal of flux is recommended.

Standard PTC heaters are not suitable for soldering.

Mounting

Electrode must not be scratched before/during/after the mounting process.

Contacts and housing used for assembly with thermistor have to be clean before mounting. Es-

pecially grease or oil must be removed.

When PTC thermistors are encapsulated with sealing material, the precautions given in chapter

"Mounting instructions", "Sealing and potting" must be observed.

When the thermistor is mounted, there must not be any foreign body between the electrode of

the thermistor and the clamping contact.

The minimum force of the clamping contacts pressing against the PTC must be 10 N.

During operation, the thermistor’s surface temperature can be very high. Ensure that adjacent

components are placed at a sufficient distance from the thermistor to allow for proper cooling at

the thermistors.

Ensure that adjacent materials are designed for operation at temperatures comparable to the

surface temperature of thermistor. Be sure that surrounding parts and materials can withstand

this temperature.

Avoid contamination of thermistor surface during processing.

Please read Cautions and warnings and

Important notes at the end of this document.

Page 5 of 7

Sensors

Limit temperature sensors, leaded disks, coated

C100

Operation

Use thermistors only within the specified temperature operating range.

Use thermistors only within the specified voltage and current ranges.

Environmental conditions must not harm the thermistors. Use thermistors only in normal at-

mospheric conditions. Avoid use in deoxidizing gases (chlorine gas, hydrogen sulfide gas, am-

monia gas, sulfuric acid gas etc), corrosive agents, humid or salty conditions.Contact with any

liquids and solvents should be prevented.

Be sure to provide an appropriate fail-safe function to prevent secondary product damage

caused by abnormal function (e.g. use VDR for limitation of overvoltage condition).

Please read Cautions and warnings and

Important notes at the end of this document.

Page 6 of 7

Important notes

The following applies to all products named in this publication:

1. Some parts of this publication contain statements about the suitability of our products for

certain areas of application. These statements are based on our knowledge of typical re-

quirements that are often placed on our products in the areas of application concerned. We

nevertheless expressly point out that such statements cannot be regarded as binding

statements about the suitability of our products for a particular customer application.

As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar

with them than the customers themselves. For these reasons, it is always ultimately incum-

bent on the customer to check and decide whether an EPCOS product with the properties de-

scribed in the product specification is suitable for use in a particular customer application.

2. We also point out that in individual cases, a malfunction of electronic components or

failure before the end of their usual service life cannot be completely ruled out in the

current state of the art, even if they are operated as specified. In customer applications

requiring a very high level of operational safety and especially in customer applications in

which the malfunction or failure of an electronic component could endanger human life or

health (e.g. in accident prevention or lifesaving systems), it must therefore be ensured by

means of suitable design of the customer application or other action taken by the customer

(e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by

third parties in the event of malfunction or failure of an electronic component.

3. The warnings, cautions and product-specific notes must be observed.

4. In order to satisfy certain technical requirements, some of the products described in this

publication may contain substances subject to restrictions in certain jurisdictions (e.g.

because they are classed as hazardous). Useful information on this will be found in our Ma-

terial Data Sheets on the Internet (www.epcos.com/material). Should you have any more de-

tailed questions, please contact our sales offices.

5. We constantly strive to improve our products. Consequently, the products described in this

publication may change from time to time. The same is true of the corresponding product

specifications. Please check therefore to what extent product descriptions and specifications

contained in this publication are still applicable before or when you place an order. We also

reserve the right to discontinue production and delivery of products. Consequently, we

cannot guarantee that all products named in this publication will always be available. The

aforementioned does not apply in the case of individual agreements deviating from the fore-

going for customer-specific products.

6. Unless otherwise agreed in individual contracts, all orders are subject to the current ver-

sion of the "General Terms of Delivery for Products and Services in the Electrical In-

dustry" published by the German Electrical and Electronics Industry Association

(ZVEI).

7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSSP, CTVS, DSSP, MiniBlue, MKK,

MLSC, MotorCap, PCC, PhaseCap, PhaseMod, SIFERRIT, SIFI, SIKOREL, SilverCap,

SIMDAD, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks

registered or pending in Europe and in other countries. Further information will be found on

the Internet at www.epcos.com/trademarks.

Page 7 of 7

B59100-C920-A70 [EPCOS]

相关型号：

B59100-M1060-A70

B59100-M1070-A70

B59100-M1080-A70

B59100-M1090-A70

B59100-M1100-A70

B59100-M1110-A70

B59100-M1120-A70

B59100-M1130-A70

B59100-M1140-A70

B59100-M1145-A70

B59100-M1150-A70

B59100-M1155-A70