PKF2611PI/A [ERICSSON]
Analog Circuit, Hybrid, PDIP18;型号: | PKF2611PI/A |
厂家: | ERICSSON |
描述: | Analog Circuit, Hybrid, PDIP18 光电二极管 |
文件: | 总16页 (文件大小:1684K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
PKF 2000 I
6–12 W DC/DC Power Modules
24 V Input Series
• SMD and through-hole versions
with ultra low component height
8 mm (0.315 in)
• 84% efficiency (typ at 5V)
• 1,500 Vdc isolation voltage
• Output current up to 2 A
• Switching frequency syncronization
• MTBF > 4.9 million hours at
+50°C pin temperature (+40°C
ambient)
• Low EMI measured according to
CISPR 22 and FCC part 15J
Patents
US: D357901 DE: M94022763
The MacroDens™ PKF 2000 I series true component
level on-board DC/DC power modules are intended
as distributed power sources in decentralized +24V
DC power system.
Utilization of thick film technology and a high
degree of silicon integration has made it possible to
achieve a MTBF of more than 4.9 million hours.
The highly reliable and rugged over-moulded design
and the ultra low height makes them particularly
suited for cellular radio and other demanding
industrial applications, with board spacing down to
15 mm or 0.6 in.
temperature range in compliance with present and
future application needs, including non temperature
controlled environments.
The mechanical design offers the choice of surface
mount or through-hole versions, delivered in ready-
to-use tubes, trays or tape & reel package, and com-
patibility with semi and fully aqueous cleaning
processes.
The PKF series is manufactured using highly
automated manufacturing lines with a world-class
quality commitment and a five-year warranty.
Ericsson Microelectronics AB has been an ISO 9001
certified supplier since 1991. For a complete product
program please reference the back cover.
These DC/DC power modules are optimized for free
convection cooling and have an operational ambient
E
General
Absolute Maximum Ratings
Stress in excess of Absolute Maximum
Ratings may cause permanent damage.
Absolute Maximum Ratings, sometimes
referred to as no destruction limits, are
normally tested with one parameter at a
time exceeding the limits of Output data
or Electrical Characteristics. If exposed to
stress above these limits, function and
performance may degrade in an unspeci-
fied manner.
Characteristics
min
–45
–55
–0.5
Unit
max
+100
+125
+40
TC
TS
VI
Case temperature at full output power
Storage temperature
°C
°C
Continuous input voltage
Vdc
Isolation voltage
(input to output test voltage)
1,500
Vdc
VISO
Vtr
Transient input energy
0.01
VI
Ws
Vdc
Vdc
VRC
Vadj
–5
–5
Remote control voltage pin 10, 11 ref. to pin 18
Output adjust voltage pin 8, 9 ref. to pin 18
+40
Input TC < TCmax unless otherwise specified
Characteristics
Conditions
min
typ
max
Unit
V
Input voltage range1)
18
16
36
18
19
VI
Turn-off input voltage
Turn-on input voltage
Input capacitance
See typical characteristics
See typical characteristics
16.8
18.3
2.4
V
VIoff
VIon
CI
V
mF
NOTES:
1)
(VI=24V)
(VI=27V)
360
300
The power modules will operate down to
PIi
Input idling power
IO= 0, TC=–30…+85°C
TC=–30…+85°C,
mW
mW
VI £18V, when VI decreases, but will turn on
at VI £19V, when VI increases (see also
Operating Information.
(VI=24V)
25
40
PRC
Input stand-by power
RC connected to pin 18 (VI=27V)
2)
The test is applicable for through-hole
versions.
Environmental Characteristics
Characteristics
Test procedure & conditions
Frequency
10…500 Hz
Amplitude
Acceleration
Number of cycles
0.75 mm
10 g
10 in each axis
Vibration
(Sinusoidal)
JESD 22-B103
(IEC 68-2-6 Fc)
Frequency
10…500 Hz
Acceleration density
spectrum
Duration
MIL-STD-883
Method 2026
(IEC 68-2-34 Ed)
Random
vibration
0.5 g2/Hz
10 min in 3 directions
medium (IEC 62-2-36)
Reproducability
Shock
(Half sinus)
Peak acceleration
Shock duration
200 g
3 ms
JESD 22-B104
(IEC 68-2-27 Ea)
Temperature
Number of cycles
–40°C…+125°C
500
Temperature
change
JESD 22-A104
(IEC 68-2-14 Na)
JESD 22-A101
(IEC 68-2-3 Ca
with bias)
Temperature
Humidity
Duration
85°C
85% RH
1000 hours
Accelerated
damp heat
Solder
resistability2)
JESD 22-B106
(IEC 68-2-20 Tb 1A)
Temperature, solder
Duration
260°C
10…13 s
Duration
Temperature
Concentration
96 h
35°C
5 %
Aggressive
environment
IEC 68-2-11 Ka
2
EN/LZT 146 31 R1A (Replaces EN/LZT 137 21 R6) © Ericsson Microelectronics AB, June 2000
Mechanical Data
Through-hole version
Surface-mount version
Foot print Component side
Foot print Component side
•
•
•
•
•
•
•
•
•
•
•
•
•
12
11 10
18
16
15 14 13
17
1
2
3
4
5
6
7
8
9
•
•
•
•
•
•
3.6 [0.142]
5.0 [0.197]
40.0 [1.575]
40.0 [1.575]
∅
×
Dimensions in mm (in)
Dimensions in mm (in)
Connections
Weight
Maximum 20 g (0.71 oz).
Pin
Designation
Function
1
Out 1
Rtn
Output 1. Positive voltage ref. to Rtn.
Output return.
2
Case
3–6
7
NC
Not connected.
Sync
Synchronization input.
The case consists of semiconductor grade
epoxy with embedded pins.
Coefficient of thermal expansion (CTE) is
typ. 15 ppm/°C.
8
V
Output voltage adjust. To set typical output voltage (VOi
connect pin 8 to pin 9.
)
adj
9
NOR
TOA
RC
Connection of Nominal Output voltage Resistor. (See Operating
Information, Output Voltage Adjust).
10
11
Turn-on/off input voltage adjust (VIon/VIoff). Used to decrease the
turn-on/off input voltage threshold.
Remote control and turn-on/off input voltage adjust. Used to turn-on
and turn-off output and to set the turn-on/off input voltage threshold.
Connection Pins
12–16
17
NC
+In
–In
Not connected.
Positive input.
Negative input.
Base material is copper (Cu), first plating
is nickel (Ni) and second (outer) plating is
palladium (Pd).
18
EN/LZT 146 31 R1A (Replaces EN/LZT 137 21 R6) © Ericsson Microelectronics AB, June 2000
3
Thermal Data
Reflow Soldering Information
The PKF series of DC/DC power modules are manufactured in
surface mount technology. Extra precautions must therefore be
taken when reflow soldering the surface mount version. Neglec-
ting the soldering information given below may result in perma-
nent damage or significant degradation of power module per-
formance.
The PKF series can be reflow soldered using IR, Natural
Convection, Forced Convection or Combined IR/Convection
Technologies. The high thermal mass of the component and its
effect on DT (°C) requires that particular attention be paid to
other temperature sensitive components.
IR Reflow technology may require the overall profile time to be
extended to approximately 8–10 minutes to ensure an acceptable
DT. Higher activity flux may be more suitable to overcome the
increase in oxidation and to avoid flux burn-up.
The general profile parameters detailed in the diagram, with this
ex-tended time to reach peak temperatures, would then be
suitable.
Two-parameter model
This model provides a more precise description of the thermal
characteristics to be used for thermal calculations.
Thermally the power module can be considered as a component
and the case temperature can be used to characterize the
properties. The thermal data for a power module with the
substrate in contact with the case can be described with two
thermal resistances. One from the case to ambient air and one
from case to PB (Printed Board).
The thermal characteristics can be calculated from the following
formula:
T
PB = (TC–TA)×(Rth C–PB+Rth C–A)/Rth C–A–Pd×Rth C–PB+TA
Where:
Pd:
TC:
dissipated power, calculated as PO ×(l/h–1)
max average case temperature
TA:
ambient air temperature at the lower side of the power
module
TPB
:
temperature in the PB between the PKF connection pins
Note! These are maximum parameters. Depending on process
variations, an appropriate margin must be added.
Rth C-PB: thermal resistance from case to PB under the power
module
R
v:
R
th C-A: thermal resistance from case to ambient air
velocity of ambient air.
th C-PB is constant and Rth C-A is dependent on the air velocity.
Free convection is equal to an air velocity of approx.
0.2 – 0.3 m/s. See figure below.
Palladium plating is used on the terminal pins. A pin tem-perature
(Tp) in excess of the solder fusing temperature (+183°C for Sn/Pb
63/37) for more than 25 seconds and a peak temperature above
195°C, is required to guarantee a reliable solder joint.
Both pin 1 and pin 9 must be monitored.
No responsibility is assumed if these recommendations are
not strictly followed.
4
EN/LZT 146 31 R1A (Replaces EN/LZT 137 21 R6) © Ericsson Microelectronics AB, June 2000
Safety
The PKF 2000 I series DC/DC power modules are designed in
accordance with EN 60 950, Safety of information technology
equipment including electrical business equipment. SEMKO certificate
no. 9738248.
The PKF power modules are recognized by UL and meet the
applicable requirements in UL 1950 Safety of information technology
equipment, the applicable Canadian safety requirements and UL
1012 Standard for power supplies.
The DC/DC power module shall be installed in an end-use
equipment and considerations should be given to measuring the
case temperature to comply with TCmax when in operation.
Abnormal component tests are conducted with the input
protected by an external 3 A fuse. The need for repeating these
tests in the end-use appliance shall be considered if installed in a
circuit having higher rated devices.
The isolation is an operational insulation in accordance with
EN 60 950.
The DC/DC power module is intended to be supplied by isolated
secondary circuitry and shall be installed in compliance with the
requirements of the ultimate application. One pole of the input
and one pole of the output is to be grounded or both are to be
kept floating.
The terminal pins are only intended for connection to mating
connectors of internal wiring inside the end-use equipment.
These DC/DC power modules may be used in telephone
equipment in accordance with paragraph 34 A.1 of UL 1459
(Standard for Telephone Equipment, second edition).
The galvanic isolation is verified in an electric strength test. Test
voltage (VISO) between input and output is 1,500 Vdc for
60 s. In production the test duration is decreased to 1 s.
The capacitor between input and output has a value of 1 nF and
the leakage current is less than 1µA @ 26 Vdc.
The case is designed in non-conductive epoxy. Its flamma-bility
rating meets UL 94V-0. The oxygen index is 34%.
Electrical Data
Fundamental circuit diagram, Single output
17
10
1
2
Control
11
8
9
18
7
EN/LZT 146 31 R1A (Replaces EN/LZT 137 21 R6) © Ericsson Microelectronics AB, June 2000
5
PKF 2111A PI, SI
TC = –30…+95°C, VI = 18...36V and pin 8 connected to pin 9 unless otherwise specified.
Output
Output 1
Characteristics
Conditions
Unit
min
typ
max
5.08
6.27
Output voltage initial
setting and accuracy
5.02
2.76
5.05
V
V
VOi
TC = +25 °C, IO = 1.5A, V = 27 V
I
Output adjust range1)
Long term drift in-
Output voltage
tolerance band
V
V
4.85
5.25
6.5
I
O = 0.2…2.0 A
cluded, TC>–10°C2)
VO
5.7
Idling voltage
Line regulation
Load regulation
IO = 0 A
22
15
V = 18…36 V
I
mV
IO = 2 A
V = 24…36 V
I
IO = 0.2…2.0 A, V = 27 V
104
119
213
mV
I
Load transient
recovery time
ttr
400
ms
I
O = 0.2…2.0 A, VI = 27 V
load step = 1 A
+200
–200
–0.34
2
mV
mV
V
tr
Load transient voltage
T
Temperature coefficient2)
Ramp-up time
I
O = 2 A, TC = 40...90 ºC
mV/°C
ms
coeff
tr
IO =2 A, 0.1…0.9 × VOi
IO = 0.2…2.0 A, V = 27 V
I
ts
Start-up time
3
ms
From V connection to VO = 0.9 × VOi
I
IO
Output current
0
2
A
Max output power2)
10
W
Calculated value
POmax
Current limiting
threshold
2.24
2.38
2.47
A
Ilim
Isc
TC <TCmax, VO = 4 V
VO = 0.2… 0.5 V, TA = +25°C
2.4
13
3.6
50
A
Short circuit current
Output ripple & noise
20 Hz… 5 MHz
0.6…50 MHz
mV
p-p
VOac
SVR
IO = 2 A
80
dBmV
f = 100 Hz sine wave, 1Vp-p V = 27 V
(SVR = 20 log (1 Vp-p/VOp-p))
,
I
Supply voltage rejection (ac)
50
dB
1) See also Operating Information.
2)
See also Typical Characteristics.
Miscellaneous
Characteristics
Conditions
typ
83
Unit
min
max
81
VI = 24 V
h
Efficiency
%
VI = 27 V
78
82
IO = 2 A
VI = 24 V
2.1
2.2
2.4
2.9
W
Pd
Power dissipation
VI = 27 V
6
EN/LZT 146 31 R1A (Replaces EN/LZT 137 21 R6) © Ericsson Microelectronics AB, June 2000
PKF 2113 PI, SI
TC = –30…+95°C, VI = 18...36V and pin 8 connected to pin 9 unless otherwise specified.
Output
Output 1
Characteristics
Conditions
Unit
min
typ
max
12.06
15.0
Output voltage initial
setting and accuracy
11.94
6.5
12.00
V
V
VOi
TC = +25 °C, IO = 0.8A, V = 27 V
I
Output adjust range1)
Long term drift
IO = 0.1…1.0 A
included
Output voltage
tolerance band
11.6
12.6
16.3
V
V
VO
13.4
IO = 0 A
Idling voltage
33
mV
mV
Line regulation
Load regulation
V = 18…36V
I
IO = 1 A
IO = 0.1…1.0 A, V = 27 V
224
I
Load transient
recovery time
ttr
760
ms
I
O = 0.1… 1.0 A, VI = 27 V
load step = 0.5 A
+120
mV
V
tr
Load transient voltage
–120
0
mV
Temperature coefficient2)
Ramp-up time
I
O = 1 A, TC = 40...90 ºC
O = 1 A, 0.1… 0.9 × VOi
mV/°C
T
coeff
tr
I
2.3
3.1
ms
ms
IO = 0.1… 1.0 A, V = 27 V
From V connection to VO = 0.9 × VOi
I
ts
Start-up time
I
Output current
IO
0
1
A
POmax
Max output power2)
Calculated value
12
W
Current limiting
threshold
1.4
A
Ilim
Isc
TC <TCmax, VO = 9.6 V
VO = 0.2… 0.5 V, TA = +25°C
20 Hz… 5 MHz
2.1
15
A
Short circuit current
Output ripple & noise
50
80
mVp-p
dBmV
VOac
IO = 1 A
0.6…50 MHz
f = 100 Hz sine wave, 1Vp-p V = 27 V
(SVR = 20 log (1 Vp-p/VOp-p))
,
I
SVR
Supply voltage rejection (ac)
50
dB
1) See also Operating Information.
2) See also Typical Characteristics.
Miscellaneous
Characteristics
Conditions
min
typ
Unit
max
83
86
VI = 24 V
VI = 27 V
VI = 24 V
VI = 27 V
h
Efficiency
%
83
86
2
IO = 1 A
2.5
2.5
W
Pd
Power dissipation
2
EN/LZT 146 31 R1A (Replaces EN/LZT 137 21 R6) © Ericsson Microelectronics AB, June 2000
7
PKF 2610A PI, SI
TC = –30…+95°C, VI = 18...36V and pin 8 connected to pin 9 unless otherwise specified.
Output
Output 1
Characteristics
Conditions
Unit
min
typ
max
3.33
3.80
Output voltage initial
setting and accuracy
3.27
1.80
3.30
V
V
VOi
TC = +25°C, IO = 1.0 A, V = 27 V
I
Output adjust range1)
Long term drift
included
Output voltage
tolerance band
I
O = 0.2…2.0 A
3.17
3.43
4.0
V
V
VO
3.8
Idling voltage
Line regulation
Load regulation
IO = 0 A
50
35
V = 18…36 V
I
mV
IO = 2 A
V = 27…36 V
I
IO = 0.2…2.0 A, V = 27 V
120
mV
I
Load transient
recovery time
ttr
100
ms
I
O = 0.2…2.0 A, V = 27 V
I
load step = 1 A
+180
mV
mV
V
tr
Load transient voltage
–
180
Temperature coefficient2)
Ramp-up time
I
O = 2 A, TC = 40...90 ºC
-0.55
2.3
mV/°C
ms
T
coeff
tr
IO = 2 A, 0.1… 0.9 × VOi
IO = 0.2…2.0 A, V = 27 V
I
ts
Start-up time
4.4
ms
From V connection to VO = 0.9 × VOi
I
IO
Output current
0
2
A
Calculated value
TC <TCmax
POmax
Max output power2)
6.6
W
Current limiting
threshold
2.2
2.6
A
Ilim
Isc
VO = 0.2… 0.5 V, TA = +25°C
2.9
15
A
Short circuit current
Output ripple & noise
20 Hz… 5 MHz
20 Hz…50 MHz
50
80
mV
p-p
VOac
IO = 2 A
dBmV
f = 100 Hz sine wave, 1Vp-p V = 27 V
(SVR = 20 log (1 Vp-p/VOp-p))
,
I
SVR
Supply voltage rejection (ac)
63
dB
1) See also Operating Information.
2) See also Typical Characteristics.
Miscellaneous
Characteristics
min
typ
81
Unit
%
Conditions
max
76
h
Efficiency
IO = 2 A, V = 27 V
I
1.6
2.1
W
Pd
Power dissipation
IO = 2 A, V = 27 V
I
8
EN/LZT 146 31 R1A (Replaces EN/LZT 137 21 R6) © Ericsson Microelectronics AB, June 2000
PKF 2611 PI, SI
TC = –30…+95°C, VI = 18...36V and pin 8 connected to pin 9 unless otherwise specified.
Output
Output 1
Characteristics
Conditions
Unit
min
typ
max
5.08
5.80
Output voltage initial
setting and accuracy
5.02
4.30
5.05
V
V
VOi
TC = +25°C, IO = 0.5 A, V = 27 V
I
Output adjust range1)
Long term drift
IO = 0.12…1.2 A
included
Output voltage
tolerance band
4.85
5.25
V
V
VO
5.8
Idling voltage
Line regulation
Load regulation
IO = 0 A
30
10
V = 18…36 V
I
mV
IO = 1.2 A
V = 27…36 V
I
IO = 0.12…1.2 A, V = 27 V
125
mV
I
Load transient
recovery time
ttr
50
ms
I
O = 0.12…1.2 A, V = 27 V
I
load step = 0.6 A
+100
mV
mV
V
tr
Load transient voltage
–
100
Temperature coefficient2)
Ramp-up time
I
O = 1.2 A, TC = 40...90 ºC
-0.8
2.3
mV/°C
ms
T
coeff
tr
IO = 1.2 A, 0.1… 0.9 × VOi
IO = 0.12…1.2 A, V = 27 V
I
ts
Start-up time
4.6
ms
From V connection to VO = 0.9 × VOi
I
IO
Output current
0
6
1.2
2.4
A
Max output power2)
W
Calculated value
TC <TCmax
POmax
Current limiting
threshold
1.3
1.6
A
Ilim
Isc
VO = 0.2… 0.5 V, TA = +25°C
2.0
20
A
Short circuit current
Output ripple & noise
20 Hz… 5 MHz
20 Hz…50 MHz
70
80
mV
p-p
VOac
IO = 1.2 A
dBmV
f = 100 Hz sine wave, 1Vp-p V = 27 V
(SVR = 20 log (1 Vp-p/VOp-p))
,
I
SVR
Supply voltage rejection (ac)
60
dB
1) See also Operating Information.
2) See also Typical Characteristics.
Miscellaneous
Characteristics
typ
Unit
min
Conditions
max
79
83
%
W
h
IO = 1.2 A, V = 27 V
Efficiency
I
1.2
1.6
Pd
Power dissipation
IO = 1.2 A, V = 27 V
I
EN/LZT 146 31 R1A (Replaces EN/LZT 137 21 R6) © Ericsson Microelectronics AB, June 2000
9
Typical Characteristics
PKF 2111A PI, SI
Output characteristic (typ)
Power derating
Efficiency (typ) @ TA = 25°C
Turn-on/turn-off input voltage
Dynamic load response (typ) @ +25°C
Temperature coefficient
The output voltage
deviation is deter-
mined by the load
transient (dI/dt)
100 mV/div
0.2 ms/div
Load change:
dI/dt » 4 A/ms
PKF 2113A PI, SI
Output characteristic (typ)
Power derating
Efficiency (typ) @ TA = 25°C
Turn-on/turn-off input voltage
Temperature coefficient
The output voltage
deviation is deter-
mined by the load
transient (dI/dt)
100 mV/div
0.2 ms/div
Load change:
dI/dt» 4 A/ms
10
EN/LZT 146 31 R1A (Replaces EN/LZT 137 21 R6) © Ericsson Microelectronics AB, June 2000
Typical Characteristics
PKF 2610A PI, SI
Output characteristic (typ)
Power derating
Efficiency (typ) @ TA = 25°C
Turn-on/turn-off input voltage
Temperature coefficient
PKF 2611 PI, SI
Output characteristic (typ)
Power derating
Efficiency (typ) @ TA = 25°C
86
84
82
80
18 V
36 V
0.4
0.6
0.8
1.0
1.2
Load current (A)
Turn-on/turn-off input voltage
Temperature coefficient
EN/LZT 146 31 R1A (Replaces EN/LZT 137 21 R6) © Ericsson Microelectronics AB, June 2000
11
Radiated EMS (Electro-Magnetic Fields)
EMC Specifications
Radiated EMS is measured according to test methods in
IEC Standard publ. 801-3. No deviation outside the VO tolerance
band will occur under the following conditions:
The fundamental switching frequency is 510 kHz 10 kHz.
Frequency range
0.01...200 MHz
200...1,000 MHz 3 Vrms/m
Voltage level
3 Vrms/m
Conducted EMI (input teminals)
1...12 GHz
10 Vrms/m
ESD
Electro Static Discharge is tested according to IEC publ. 801-2. No
destruction will occur if the following voltage levels are applied to
any of the terminal pins:
Test
Voltage level
Air discharge
Contact discharge
4 kV
2 kV
EFT
Electrical Fast Transients on the input terminals could affect the out-
put voltage regulation causing functional errors on the Printed Board
Assembly (PBA). The PKF power module withstand EFT levels of
0.5 kV keeping VO within the tolerance band and
2.0 kV without destruction. Tested according to IEC publ. 801-4.
Output Ripple & Noise (VOac)
PKF series typical conducted EMI performance
Output ripple is measured as the peak to peak voltage of the funda-
mental switching frequency.
Test set up
The PKF meets class A in VDE 0871/0878, FCC Part 15J, and CISPR 22
(EN 55022), except for the fundamental switching frequency.
Radiated EMI
Radiated emission of electromagnetic fields is measured at 10 m
distance.
30...100 MHz
100...200 MHz
200...230 MHz
60 dB mV/m
40 dB mV/m
30 dB mV/m
230...1,000 MHz 35 dB mV/m
1...10 GHz 46 dB mV/m
Conducted EMS
Electro Magnetic Susceptibility is measured by injection of
electrical disturbances on the input terminals. No deviation
outside the VO tolerance band will occur under the following
conditions:
Frequency range
0.15...300 MHz
Voltage level
1.0 Vrms
The signal is amplitude modulated with 1 kHz/80% and applied in
differential and common mode.
12
EN/LZT 146 31 R1A (Replaces EN/LZT 137 21 R6) © Ericsson Microelectronics AB, June 2000
To increase VIon a resistor should be connected between pin 11
and 18 (see fig. 3).
Operating Information
Fuse Considerations
The resistance is given by the following equation
(For VIon>18.4V):
To prevent excessive current from flowing through the input
supply line, in the case of a short-circuit across the converter in-
put, an external fuse should be installed in the non-earthed input
supply line. We recommend using a fuse rated at approximately
2 to 4 times the value calculated in the formula below:
R
Ion = (k1 – VIon)/(VIon – k2) kW
where k2 is the typical unadjusted turn-on input voltage (V).
To decrease VIon a resistor should be connected between pin 10
and 11 (see fig. 3). The resistance is given by the following
equation (for 17.0V < VIon >18.3V:
PO
max
Iin
=
max
RIon = k3 × (VIon – k4)/(k2 – VIon) kW
(hmin × VImin
)
k1
k2
k3
k4
1020
1020
1020
18.3
18.4
18.4
22
27
25
16.9
17.0
17.0
PKF 2111A, PKF 2113A
PKF 2610A
PKF 2611
Refer to the fuse manufacturer for further information.
Remote Control (RC)
Turn-off level. VIoff is the adjusted turn-off level and is deter-
mined by the following equation: VIoff = VIon – 1.5V (typical
value).
Turn-on or turn-off can be realized by using the RC-pin. Normal
operation is achieved if pin 11 is open (NC). If pin 11 is con-
nected to pin 18 the power module turns off. To ensure safe turn-
off the voltage difference between pin 11 and 18 shall be less than
1.0V. RC is an TTL open collector compatible output with a sink
capacity >300 mA (see fig. 1).
Decrease V
Increase V
Ion
Ion
TOA (pin 10)
−In (pin 18)
RIon
RIon
RC (pin 11)
RC (pin 11)
Figure 3
Output Voltage Adjust (Vadj
)
Output voltage, VO, can be adjusted by using an external resistor.
Typical adjust range is 15%. If pin 8 and 9 is not connected to-
gether the output will decrease to a low value. To increase VO a
resistor should be connected between pin 8/9 and 18, and to
decrease VO a resistor should be connected between pin 8 and 9
(see fig. 4).
Figure 1
Over Voltage Protection (OVP)
The remote control can be utilized also for OVP by using the ex-
ternal circuitry in figure 2. Resistor values are for 5V output app-
lications, but can easily be adjusted for other output voltages and
the desired OVP level.
Typical required resistor value to increase VO is given by:
R
adj = k5 × (k6 – VO)/(VO – VOi) kW
where VO is the desired output voltage,
Oi is the typical output voltage initial setting
V
Out 1 (pin 1)
and
k5= 4.2
k5= 4.2
k6= 6.27 V
k6= 15.0 V
PKF 2111A
PKF 2113A
15k
1.2k
1k
k5= 3.18
k5= 3.18
k6= 3.90V
k6= 5.85V
PKF 2610A
PKF 2611
TL431
Typical required resistor value to decrease VO is given by:
adj = k7 × (VOi – VO)/(VO – k8) kW
270
RC (pin 11)
10k
R
where k7= 18.0
k7= 18.6
k8= 2.76 V
k8= 6.50 V
k8= 1.70 V
k8= 4.28 V
PKF 2111A
PKF 2113A
PKF 2610A
PKF 2611
k7= 17.2
k7= 12.5
Rtn (pin 2)
-In (pin 18)
Figure 2
Increase VO
Decrease VO
–In (pin 18)
V
adj
(pin 8)
Turn-on/off Input Voltage
The power module monitors the input voltage and will turn on
and off at predetermined levels. The typical turn-on level (with-
out any external resistor) is 18.4 V and the typical turn-off level is
17.0 V, a slight deviation can occur due to tolerances in the
manufacturing process. These levels can be adjusted by means of
external resistors.
Radj
Radj
NOR (pin 9)
Vadj, NOR (pin 8, 9)
Figure 4
EN/LZT 146 31 R1A (Replaces EN/LZT 137 21 R6) © Ericsson Microelectronics AB, June 2000
13
Capacitive Load
Delivery Package Information
The PKF series has no maximum limit for capacitive load on the
output. The power module may operate in current limiting mode
during start-up, affecting the ramp-up and the start-up time. For
optimum start performance we recommend maximum 100 mF/A
of IO. Connect capacitors at the point of load for best perfor-
mance.
Tubes
The PKF-series is delivered in tubes (designated by /A) with a
length of 500 mm (19.69 in), see fig. 5.
Parallel Operation
Paralleling of several converters is easily accomplished by direct
connection of the output voltage terminal pins. The load regula-
tion characteristic is specifically designed for optimal paralleling
performance. Load sharing between converters will be within
10%. It is recommended not to exceed PO = n × 0.9 × PO
,
max
where POmax is the maximum converter output power and n the
number of paralleled converters, to prevent overloading any of the
converters and thereby decreasing the reliability performance.
igure 5
Specification
Current Limiting Protection (Ilim
The output power is limited at loads above the output current
limiting threshold (Ilim), specified as a minimum value.
)
Material:
Antistatic coated PVC
Max surface resistance: 1011W/
Color:
Transparent
10 power modules/tube
Typ. 60 g
Capacity:
Weight:
End stops:
Pins
Synchronization (Sync)
It is possible to synchronize the switching frequency to an
external symmetrical clock signal. The input is TTL-compatible
and referenced to the input pin 18.
Trays
SMD versions, SI, can be delivered in standard JEDEC trays
(designated by /B) on request, see fig. 6. For more information,
please contact your local Ericsson sales office.
Characteristics
min
typ
max
unit
High level
2.2
1.2
0
6.5
2.2
0.4
1.5
688
V
V
Threshold level*)
Low level
1.7
V
Sink current
Sync. frequency
mA
kHz
520
*) Rise time <10ns
Input and Output Impedance
Both the source impedance of the power feeding and the load im-
pedance will interact with the impedance of the DC/DC power
module.
It is most important to have the ratio between L and C as low
as possible, i.e. a low characteristic impedance, both at the input
and output, as the power modules have a low energy storage
capability.
Use an electrolytic capacitor across the input if the source
inductance is larger than 10 mH. Their equivalent series resist-
ance together with the capacitance acts as a lossless damping fil-
ter. Suitable capacitor values are in the range 10–100 mF.
Figure 6
Specification
Material:
Max temperature:
Max surface resistance: 105W/
Polypropylene (PP)
125ºC
Color:
Black
14
EN/LZT 146 31 R1A (Replaces EN/LZT 137 21 R6) © Ericsson Microelectronics AB, June 2000
Capacity:
Stacking pitch:
Weight:
15 power modules/tray
10.16 mm
Typ. 130 g
Quality
Reliability
Min. order quantity: 150 pcs (one box contains 10 full trays)
Meantime between failure (MTBF) is calculated to >4.9 million
hours at full output power and a pin temperature of +50°C
(TA = +40°C), using the Ericsson failure rate data system.
The Ericsson failure rate data system is based on field failure
rates and is continously updated. The data corresponds to actual
failure rates of components used in Information Technology and
Telecom equipment in temperature controlled environments
(TA = –5… +65°C). The data is considered to have a confidence
level of 90%. For more information see Design Note 002.
Tape & Reel
SMD versions, SI, can be delivered in standard tape & reel pack-
age (designated by /C) on request, see fig. 7. For more informa-
tion, please contact your local Ericsson sales office.
Quality Statement
The products are designed and manufactured in an industrial en-
vironment where quality systems and methods like ISO 9000, 6s
and SPC, are intensively in use to boost the continuous improve-
ments strategy. Infant mortality or early failures in the products
are screened out by a burn-in procedure and an ATE-based final
test.
Conservative design rules, design reviews and product qualifi-
cations, plus the high competence of an engaged work force, con-
tribute to the high quality of our products.
Warranty
Ericsson Microelectronics warrants to the original purchaser or
end user that the products conform to this Data Sheet and are free
from material and workmanship defects for a period of five (5)
years from the date of manufacture, if the product is used within
specified conditions and not opened. In case the product is dis-
continued, claims will be accepted up to three (3) years from the
date of the discontinuation.
Figure 7
For additional details on this limited warranty please refer to
Ericsson Microelectronics AB’s “General Terms and Conditions of
Sales”, or individual contract documents.
Specification
Tape material:
Tape width:
Tape pitch:
Max surface resistance: 105W/
Conductive polystyrene (PS)
72 mm
36 mm
Limitation of liability
Tape color:
Black
Cover tape color:
Reel diameter:
Reel hub diameter:
Reel capacity:
Full reel weight:
Min. order quantity:
Transparent
13"
7"
150 power modules/reel
Typ. 3.7 kg
300 pcs (one box contains two reels)
Ericsson Microelectronics does not make any other warranties, ex-
pressed or implied including any warranty of merchantability or
fitness for a particular purpose (including, but not limited to, use
in life support applications, where malfunctions of product can
cause injury to a person’s health or life).
Information given in this data sheet is believed to be accurate and reliable. No
responsibility is assumed for the consequences of its use nor for any infringement
of patents or other rights of third parties which may result from its use.
No license is granted by implication or otherwise under any patent or patent rights
of Ericsson Microelectronics. These products are sold only according to Ericsson
Microelectronics’ general conditions of sale, unless otherwise confirmed in writing.
Specifications subject to change without notice.
EN/LZT 146 31 R1A (Replaces EN/LZT 137 21 R6) © Ericsson Microelectronics AB, June 2000
15
Product Program
Ordering No.*)
Through-hole
VO/IO max
VI
PO max
Output 1
SMD
5 V/2.0 A
12 V/1.0 A
3.3 V/2.0 A
0.5 V/1.2 A
10 W
12 W
6.6 W
6.0 W
PKF 2111A PI
PKF 2113A PI
PKF 2610A PI
PKF 2611A PI
PKF 2111A SI
PKF 2113A SI
PKF 2610A SI
PKF 2611A SI
24 V
*)
See also Delivery Package Information
The latest and most complete infor-
mation can be found on our website!
Ericsson Microelectronics AB
SE-164 81 KISTA, Sweden
Phone: +46 8 757 5000
www.ericsson.com/microelectronics
Data Sheet
For local sales contacts, please refer to our website
or call: Int. +46 8 757 4700, Fax: +46 8 757 4776
EN/LZT 146 31 R1A (Replaces EN/LZT 137 21 R6)
© Ericsson Microelectronics AB, June 2000
相关型号:
©2020 ICPDF网 联系我们和版权申明