24AA02-I/SM [ETC]
I2C Serial EEPROM ; I2C串行EEPROM\n![24AA02-I/SM](http://pdffile.icpdf.com/pdf1/p00012/img/icpdf/24AA0_56818_icpdf.jpg)
型号: | 24AA02-I/SM |
厂家: | ![]() |
描述: | I2C Serial EEPROM
|
文件: | 总12页 (文件大小:162K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
![](http://public.icpdf.com/style/img/ads.jpg)
M
24AA01/02
2 ™
1K 1.8V I C Serial EEPROM
FEATURES
PACKAGE TYPES
• Single supply with operation down to 1.8V
• Low power CMOS technology
PDIP
- 1 mA active current typical
A0
A1
1
2
8
7
VCC
WP
- 10 µA standby current typical at 5.5V
- 3 µA standby current typical at 1.8V
• Organized as a single block of 128 bytes (128 x 8)
or 256 bytes (256 x 8)
• 2-wire serial interface bus, I2C compatible
A2
3
4
6
5
SCL
SDA
• Schmitt trigger, filtered inputs for noise suppres-
sion
VSS
• Output slope control to eliminate ground bounce
• 100 kHz (1.8V) and 400 kHz (5V) compatibility
• Self-timed write cycle (including auto-erase)
• Page-write buffer for up to 8 bytes
SOIC
• 2 ms typical write cycle time for page-write
• Hardware write protect for entire memory
• Can be operated as a serial ROM
1
2
8
7
A0
A1
VCC
• ESD protection > 3,000V
WP
• 1,000,000 ERASE/WRITE cycles guaranteed
• Data retention > 200 years
3
4
6
5
A2
SCL
SDA
• 8-pin DIP or SOIC package
VSS
• Available for extended temperature ranges
- Commercial (C):
- Industrial (I):
0°C to +70°C
-40°C to +85°C
DESCRIPTION
BLOCK DIAGRAM
The Microchip Technology Inc. 24AA01 and 24AA02
are 1K bit and 2K bit Electrically Erasable PROMs.The
devices are organized as a single block of 128 x 8-bit
or 256 x 8-bit memory with a two wire serial interface.
Low-voltage design permits operation down to 1.8 volts
with standby and active currents of only 3 µA and 1 mA,
respectively.The 24AA01 and 24AA02 also have page-
write capability for up to 8 bytes of data. The 24AA01
and 24AA02 are available in the standard 8-pin DIP
and 8-pin surface mount SOIC packages.
WP
HV GENERATOR
I/O
CONTROL
LOGIC
MEMORY
CONTROL
LOGIC
EEPROM
ARRAY
XDEC
PAGE LATCHES
SDA
SCL
YDEC
VCC
VSS
SENSE AMP
R/W CONTROL
I2C is a trademark of Philips Corporation
1998 Microchip Technology Inc.
DS21052H-page 1
Powered by ICminer.com Electronic-Library Service CopyRight 2003
24AA01/02
other conditions above those indicated in the operational listings
of this specification is not implied. Exposure to maximum rating
conditions for extended periods may affect device reliability.
1.0
ELECTRICAL
CHARACTERISTICS
TABLE 1-1:
Name
PIN FUNCTION TABLE
Function
1.1
Maximum Ratings*
VCC...................................................................................7.0V
All inputs and outputs w.r.t. VSS ................-0.6V to VCC +1.0V
Storage temperature .....................................-65°C to +150°C
Ambient temp. with power applied..............-65°C to +125°CC
Soldering temperature of leads (10 seconds) .............+300°C
ESD protection on all pins..................................................≥ 4 kV
VSS
SDA
Ground
Serial Address/Data/I/O
Serial Clock
SCL
WP
Write Protect Input
*Notice: Stresses above those listed under “Maximum ratings”
may cause permanent damage to the device. This is a stress rat-
ing only and functional operation of the device at those or any
VCC
+1.8V to 5.5V Power Supply
No Internal Connection
A0, A1, A2
TABLE 1-2:
DC CHARACTERISTICS
VCC = +1.8V to +5.5V
Commercial (C):Tamb = 0°C to +70°C
Industrial (I): Tamb = -40°C to +85°C
Parameter
Symbol
Min
Typ
Max
Units
Conditions
WP, SCL and SDA pins:
High level input voltage
Low level input voltage
Hysteresis of Schmitt trigger
inputs
VIH
VIL
VHYS
.7 VCC
—
.05 VDD
—
—
—
—
.3 VCC
—
V
V
V
(Note)
IOL = 3.0 mA, VCC = 1.8V
Low level output voltage
VOL
ILI
—
-10
-10
—
—
—
—
—
.40
10
10
10
V
Input leakage current
Output leakage current
µA
µA
pF
VIN = .1V to 5.5V
ILO
VOUT = .1V to 5.5V
Pin capacitance
CIN,
Vcc = 5.0V (Note 1)
(all inputs/outputs)
COUT
Tamb = 25˚C, FLCK = 1 MHz
Operating current
ICC Write
—
—
—
—
—
0.5
—
3
—
1
mA
mA
mA
mA
VCC = 5.5V, SCL = 400 kHz
VCC = 1.8V, SCL = 100 kHz
VCC = 5.5V, SCL = 400 kHz
VCC = 1.8V, SCL = 100 kHz
ICC Read
0.05
—
Standby current
ICCS
—
—
—
—
—
3
100
30
—
µA
µA
µA
VCC = 5.5V, SDA = SCL = VCC
VCC = 3.0V, SDA = SCL = VCC
VCC = 1.8V, SDA = SCL = VCC
WP = VSS
Note:This parameter is periodically sampled and not 100% tested.
FIGURE 1-1: BUS TIMING START/STOP
VHYS
SCL
SDA
THD:STA
TSU:STA
TSU:STO
START
STOP
DS21052H-page 2
1998 Microchip Technology Inc.
Powered by ICminer.com Electronic-Library Service CopyRight 2003
24AA01/02
TABLE 1-3:
AC CHARACTERISTICS
VCC = 4.5 - 5.5V
Fast Mode
Standard Mode
Parameter
Symbol
Units
Remarks
Min
Max
Min
Max
Clock frequency
FCLK
THIGH
TLOW
TR
—
4000
4700
—
100
—
—
600
1300
—
400
—
kHz
ns
Clock high time
Clock low time
—
—
ns
SDA and SCL rise time
SDA and SCL fall time
START condition hold time
1000
300
—
300
300
—
ns
(Note 1)
(Note 1)
TF
—
—
ns
THD:STA
4000
600
ns
After this period the first
clock pulse is generated
START condition setup
time
TSU:STA
4700
—
600
—
ns
Only relevant for repeated
START condition
Data input hold time
Data input setup time
STOP condition setup time
Output valid from clock
Bus free time
THD:DAT
TSU:DAT
TSU:STO
TAA
0
—
—
0
—
—
ns
ns
ns
ns
ns
(Note 2)
250
4000
—
100
600
—
—
—
3500
—
900
—
(Note2)
TBUF
4700
1300
Time the bus must be free
before a new transmis-
sion can start
Output fall time from VIH
min to VIL max
TOF
TSP
—
—
250
50
20 +0.1
CB
250
50
ns
ns
(Note 1), CB ≤ 100 pF
Input filter spike suppres-
sion (SDA and SCL pins)
—
(Note 3)
Write cycle time
Endurance
TWR
—
—
10
—
—
10
—
ms
Byte or Page mode
1M
1M
cycles 25°C, Vcc = 5.5V, Block
Mode (Note 4)
Note 1: Not 100% tested. CB = total capacitance of one bus line in pF.
2: As a transmitter, the device must provide an internal minimum delay time to bridge the undefined region
(minimum 300 ns) of the falling edge of SCL to avoid unintended generation of START or STOP conditions.
3: The combined TSP and VHYS specifications are due to new Schmitt trigger inputs which provide improved
noise spike suppression. This eliminates the need for a TI specification for standard operation.
4: This parameter is not tested but guaranteed by characterization. For endurance estimates in a specific appli-
cation, please consult the Total Endurance Model which can be obtained on our BBS or website.
FIGURE 1-2: BUS TIMING DATA
TR
TF
THIGH
TLOW
SCL
TSU:STA
THD:DAT
TSU:DAT
TSU:STO
THD:STA
SCL
IN
TSP
TBUF
TAA
TAA
THD:STA
SDA
OUT
1998 Microchip Technology Inc.
DS21052H-page 3
Powered by ICminer.com Electronic-Library Service CopyRight 2003
24AA01/02
3.4
Data Valid (D)
2.0
FUNCTIONAL DESCRIPTION
The 24AA01/02 supports a bi directional 2-wire bus
and data transmission protocol. A device that sends
data onto the bus is defined as transmitter, and a
device receiving data as receiver. The bus has to be
controlled by a master device which generates the
serial clock (SCL), controls the bus access, and gener-
ates the START and STOP conditions, while the
24AA01/02 works as slave. Both, master and slave can
operate as transmitter or receiver but the master device
determines which mode is activated.
The state of the data line represents valid data when,
after a START condition, the data line is stable for the
duration of the HIGH period of the clock signal.
The data on the line must be changed during the LOW
period of the clock signal. There is one clock pulse per
bit of data.
Each data transfer is initiated with a START condition
and terminated with a STOP condition. The number of
the data bytes transferred between the START and
STOP conditions is determined by the master device
and is theoretically unlimited, although only the last 16
will be stored when doing a write operation. When an
overwrite does occur it will replace data in a first in first
out fashion.
3.0
BUS CHARACTERISTICS
The following bus protocol has been defined:
• Data transfer may be initiated only when the bus
is not busy.
3.5
Acknowledge
• During data transfer, the data line must remain
stable whenever the clock line is HIGH. Changes
in the data line while the clock line is HIGH will be
interpreted as a START or STOP condition.
Each receiving device, when addressed, is obliged to
generate an acknowledge after the reception of each
byte. The master device must generate an extra clock
pulse which is associated with this acknowledge bit.
Accordingly, the following bus conditions have been
defined (Figure 3-1).
Note: The 24AA01/02 does not generate any
acknowledge bits if an internal program-
ming cycle is in progress.
3.1
Bus not Busy (A)
Both data and clock lines remain HIGH.
The device that acknowledges, has to pull down the
SDA line during the acknowledge clock pulse in such a
way that the SDA line is stable LOW during the HIGH
period of the acknowledge related clock pulse. Of
course, setup and hold times must be taken into
account. A master must signal an end of data to the
slave by not generating an acknowledge bit on the last
byte that has been clocked out of the slave. In this
case, the slave must leave the data line HIGH to enable
the master to generate the STOP condition.
3.2
Start Data Transfer (B)
A HIGH to LOW transition of the SDA line while the
clock (SCL) is HIGH determines a START condition.
All commands must be preceded by a START condi-
tion.
3.3
Stop Data Transfer (C)
A LOW to HIGH transition of the SDA line while the
clock (SCL) is HIGH determines a STOP condition. All
operations must be ended with a STOP condition.
FIGURE 3-1: DATA TRANSFER SEQUENCE ON THE SERIAL BUS
DSCL
(A)
(B)
(D)
(D)
(C)
(A)
or
MSCL
DSCL
or
MSCL
START
CONDITION
STOP
CONDITION
ADDRESS OR
ACKNOWLEDGE
VALID
DATA
ALLOWED
TO CHANGE
DS21052H-page 4
1998 Microchip Technology Inc.
Powered by ICminer.com Electronic-Library Service CopyRight 2003
24AA01/02
3.6
Device Address
4.0
WRITE OPERATION
The 24AA01/02 are software-compatible with older
devices such as 24C01A, 24C02A, 24LC01, and
24LC02. A single 24AA02 can be used in place of two
24LC01's, for example, without any modifications to
software. The “chip select” portion of the control byte
becomes a don't care.
4.1
Byte Write
Following the start signal from the master, the device
code (4 bits), the don't care bits (3 bits), and the R/W
bit which is a logic low is placed onto the bus by the
master transmitter. This indicates to the addressed
slave receiver that a byte with a word address will follow
after it has generated an acknowledge bit during the
ninth clock cycle.Therefore the next byte transmitted by
the master is the word address and will be written into
the address pointer of the 24AA01/02. After receiving
another acknowledge signal from the 24AA01/02 the
master device will transmit the data word to be written
into the addressed memory location. The 24AA01/02
acknowledges again and the master generates a stop
condition.This initiates the internal write cycle, and dur-
ing this time the 24AA01/02 will not generate acknowl-
edge signals (Figure 4-1).
After generating a START condition, the bus master
transmits the slave address consisting of a 4-bit device
code (1010) for the 24AA01/02, followed by three don't
care bits.
The eighth bit of slave address determines if the master
device wants to read or write to the 24AA01/02
(Figure 3-2).
The 24AA01/02 monitors the bus for its corresponding
slave address all the time. It generates an acknowledge
bit if the slave address was true and it is not in a pro-
gramming mode.
4.2
Page Write
Control
Code
Operation
Chip Select
R/W
The write control byte, word address and the first data
byte are transmitted to the 24AA01/02 in the same way
as in a byte write. But instead of generating a stop con-
dition the master transmits up to eight data bytes to the
24AA01/02 which are temporarily stored in the on-chip
page buffer and will be written into the memory after the
master has transmitted a stop condition. After the
receipt of each word, the three lower order address
pointer bits are internally incremented by one. The
higher order five bits of the word address remains con-
stant. If the master should transmit more than eight
words prior to generating the stop condition, the
address counter will roll over and the previously
received data will be overwritten. As with the byte write
operation, once the stop condition is received an inter-
nal write cycle will begin (Figure 7-1).
Read
Write
1010
1010
XXX
XXX
1
0
FIGURE 3-2: CONTROL BYTE
ALLOCATION
START
READ/WRITE
SLAVE ADDRESS
R/W
A
1
0
1
0
X
X
X
X = Don’t care
Note: Page write operations are limited to writing
bytes within a single physical page, regard-
less of the number of bytes actually being
written. Physical page boundaries start at
addresses that are integer multiples of the
page buffer size (or Ôpage sizeÕ) and end at
addresses that are integer multiples of
[page size - 1]. If a page write command
attempts to write across a physical page
boundary, the result is that the data wraps
around to the beginning of the current page
(overwriting data previously stored there),
instead of being written to the next page as
might be expected. It is therefore neces-
sary for the application software to prevent
page write operations that would attempt to
cross a page boundary.
1998 Microchip Technology Inc.
DS21052H-page 5
Powered by ICminer.com Electronic-Library Service CopyRight 2003
24AA01/02
FIGURE 4-1: BYTE WRITE
S
T
A
R
T
S
T
O
P
BUS ACTIVITY
MASTER
CONTROL
BYTE
WORD
ADDRESS
DATA
SDA LINE
S
P
A
C
K
A
C
K
A
C
K
BUS ACTIVITY
FIGURE 4-2: PAGE WRITE
S
BUS ACTIVITY
MASTER
T
A
R
T
S
T
O
P
CONTROL
BYTE
WORD
ADDRESS (n)
DATA n
DATA n + 1
DATA n + 7
SDA LINE
S
P
A
C
K
A
C
K
A
C
K
A
C
K
A
C
K
BUS ACTIVITY
DS21052H-page 6
1998 Microchip Technology Inc.
Powered by ICminer.com Electronic-Library Service CopyRight 2003
24AA01/02
5.0
ACKNOWLEDGE POLLING
7.0
READ OPERATION
Since the device will not acknowledge during a write
cycle, this can be used to determine when the cycle is
complete (this feature can be used to maximize bus
throughput). Once the stop condition for a write com-
mand has been issued from the master, the device ini-
tiates the internally timed write cycle. ACK polling can
be initiated immediately.This involves the master send-
ing a start condition followed by the control byte for a
write command (R/W = 0). If the device is still busy with
the write cycle, then no ACK will be returned. If the
cycle is complete, then the device will return the ACK
and the master can then proceed with the next read or
write command. See Figure 5-1 for flow diagram.
Read operations are initiated in the same way as write
operations with the exception that the R/W bit of the
slave address is set to one. There are three basic types
of read operations: current address read, random
read, and sequential read.
7.1
Current Address Read
The 24AA01/02 contains an address counter that
maintains the address of the last word accessed, inter-
nally incremented by one. Therefore, if the previous
access (either a read or write operation) was to
address n, the next current address read operation
would access data from address n + 1. Upon receipt of
the slave address with R/W bit set to one, the 24AA01/
02 issues an acknowledge and transmits the eight bit
data word. The master will not acknowledge the trans-
fer but does generate a stop condition and the 24AA01/
02 discontinues transmission (Figure 7-1).
FIGURE 5-1: ACKNOWLEDGE POLLING
FLOW
Send
Write Command
7.2
Random Read
Random read operations allow the master to access
any memory location in a random manner. To perform
this type of read operation, first the word address must
be set.This is done by sending the word address to the
24AA01/02 as part of a write operation. After the word
address is sent, the master generates a start condition
following the acknowledge. This terminates the write
operation, but not before the internal address pointer is
set. Then the master issues the control byte again but
with the R/W bit set to a one. The 24AA01/02 will then
issue an acknowledge and transmits the eight bit data
word. The master will not acknowledge the transfer but
does generate a stop condition and the 24AA01/02 dis-
continues transmission (Figure 7-2).
Send Stop
Condition to
Initiate Write Cycle
Send Start
Send Control Byte
with R/W = 0
Did Device
No
Acknowledge
7.3
Sequential Read
(ACK = 0)?
Sequential reads are initiated in the same way as a ran-
dom read except that after the 24AA01/02 transmits the
first data byte, the master issues an acknowledge as
opposed to a stop condition in a random read. This
directs the 24AA01/02 to transmit the next sequentially
addressed 8-bit word (Figure 7-3).
Yes
Next
Operation
To provide sequential reads the 24AA01/02 contains an
internal address pointer which is incremented by one at
the completion of each operation. This address pointer
allows the entire memory contents to be serially read
during one operation.
6.0
WRITE PROTECTION
The 24AA01/02 can be used as a serial ROM when the
WP pin is connected to VCC. Programming will be inhib-
ited and the entire memory will be write-protected.
7.4
Noise Protection
The 24AA01/02 employs a VCC threshold detector cir-
cuit which disables the internal erase/write logic if the
VCC is below 1.5 volts at nominal conditions.
The SCL and SDA inputs have Schmitt trigger and filter
circuits which suppress noise spikes to assure proper
device operation even on a noisy bus.
1998 Microchip Technology Inc.
DS21052H-page 7
Powered by ICminer.com Electronic-Library Service CopyRight 2003
24AA01/02
FIGURE 7-1: CURRENT ADDRESS READ
S
T
A
R
T
S
T
O
P
BUS ACTIVITY
MASTER
CONTROL
BYTE
DATA n
SDA LINE
S
P
A
C
K
N
O
BUS ACTIVITY
A
C
K
FIGURE 7-2: RANDOM READ
S
T
A
R
T
S
T
A
R
T
S
T
O
P
BUS ACTIVITY
MASTER
CONTROL
BYTE
WORD
ADDRESS (n)
CONTROL
BYTE
DATA (n)
S
P
S
SDA LINE
A
C
K
A
C
K
A
C
K
N
O
BUS ACTIVITY
A
C
K
FIGURE 7-3: SEQUENTIAL READ
S
T
O
P
BUS ACTIVITY
MASTER
CONTROL
BYTE
DATA n
DATA n + 1
DATA n + 2
DATA n + X
SDA LINE
P
A
C
K
A
C
K
A
C
K
A
C
K
N
O
BUS ACTIVITY
A
C
K
8.3
WP
8.0
PIN DESCRIPTIONS
This pin must be connected to either VSS or VCC.
8.1
SDA Serial Address/Data Input/Output
If tied to VSS, normal memory operation is enabled
(read/write the entire memory).
This is a bi-directional pin used to transfer addresses
and data into and data out of the device. It is an open
drain terminal, therefore the SDA bus requires a pullup
resistor to VCC (typical 10KΩ for 100 kHz, 2K for 400
kHz).
If tied to VCC, WRITE operations are inhibited. The
entire memory will be write-protected. Read opera-
tions are not affected.
This feature allows the user to use the 24AA01/02 as a
serial ROM when WP is enabled (tied to VCC).
For normal data transfer SDA is allowed to change only
during SCL low. Changes during SCL high are
reserved for indicating the START and STOP condi-
tions.
8.4
A0, A1, A2
These pins are not used by the 24AA01/02. They may
be left floating or tied to either VSS or VCC.
8.2
SCL Serial Clock
This input is used to synchronize the data transfer from
and to the device.
DS21052H-page 8
1998 Microchip Technology Inc.
Powered by ICminer.com Electronic-Library Service CopyRight 2003
24AA01/02
NOTES:
1998 Microchip Technology Inc.
DS21052H-page 9
Powered by ICminer.com Electronic-Library Service CopyRight 2003
24AA01/02
NOTES:
DS21052H-page 10
1998 Microchip Technology Inc.
Powered by ICminer.com Electronic-Library Service CopyRight 2003
24AA01/02
24AA01/02 PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office..
24AA01/02 /P
—
P = Plastic DIP (300 mil Body), 8-lead
SN = Plastic SOIC (150 mil Body), 8-lead
SM = Plastic SOIC (207 mil Body), 8-lead
Package:
Temperature
Range:
Blank = 0°C to +70°C
I = -40°C to +85°C
2
24AA01
24AA01T
24AA02
1.8V, 1K I C Serial EEPROM
2
1.8V, 1K I C Serial EEPROM (Tape and Reel)
Device:
2
1.8V, 2K I C Serial EEPROM
2
24AA02T
1.8V, 2K I C Serial EEPROM (Tape and Reel)
Sales and Support
Data Sheets
Products supported by a preliminary Data Sheet may have an errata sheet describing minor operational differences and recom-
mended workarounds. To determine if an errata sheet exists for a particular device, please contact one of the following:
1. Your local Microchip sales office
2. The Microchip Corporate Literature Center U.S. FAX: (602) 786-7277
3. The Microchip Worldwide Site (www.microchip.com)
Please specify which device, revision of silicon and Data Sheet (include Literature #) you are using.
New Customer Notification System
Register on our web site (www.microchip.com/cn) to receive the most current information on our products.
1998 Microchip Technology Inc.
DS21052H-page 11
Powered by ICminer.com Electronic-Library Service CopyRight 2003
WORLDWIDE SALES AND SERVICE
AMERICAS
AMERICAS (continued)
ASIA/PACIFIC (continued)
Corporate Office
Toronto
Singapore
Microchip Technology Inc.
Microchip Technology Inc.
Microchip Technology Singapore Pte Ltd.
200 Middle Road
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-786-7200 Fax: 480-786-7277
Technical Support: 480-786-7627
Web Address: http://www.microchip.com
5925 Airport Road, Suite 200
Mississauga, Ontario L4V 1W1, Canada
Tel: 905-405-6279 Fax: 905-405-6253
#07-02 Prime Centre
Singapore 188980
Tel: 65-334-8870 Fax: 65-334-8850
Taiwan, R.O.C
Microchip Technology Taiwan
10F-1C 207
Tung Hua North Road
Taipei, Taiwan, ROC
ASIA/PACIFIC
Hong Kong
Microchip Asia Pacific
Unit 2101, Tower 2
Atlanta
Microchip Technology Inc.
500 Sugar Mill Road, Suite 200B
Atlanta, GA 30350
Metroplaza
223 Hing Fong Road
Kwai Fong, N.T., Hong Kong
Tel: 852-2-401-1200 Fax: 852-2-401-3431
Tel: 886-2-2717-7175 Fax: 886-2-2545-0139
Tel: 770-640-0034 Fax: 770-640-0307
Boston
EUROPE
Microchip Technology Inc.
5 Mount Royal Avenue
Marlborough, MA 01752
Tel: 508-480-9990 Fax: 508-480-8575
Beijing
United Kingdom
Microchip Technology, Beijing
Unit 915, 6 Chaoyangmen Bei Dajie
Dong Erhuan Road, Dongcheng District
New China Hong Kong Manhattan Building
Beijing 100027 PRC
Arizona Microchip Technology Ltd.
505 Eskdale Road
Winnersh Triangle
Wokingham
Berkshire, England RG41 5TU
Tel: 44 118 921 5858 Fax: 44-118 921-5835
Denmark
Microchip Technology Denmark ApS
Regus Business Centre
Lautrup hoj 1-3
Ballerup DK-2750 Denmark
Tel: 45 4420 9895 Fax: 45 4420 9910
Chicago
Microchip Technology Inc.
333 Pierce Road, Suite 180
Itasca, IL 60143
Tel: 86-10-85282100 Fax: 86-10-85282104
India
Tel: 630-285-0071 Fax: 630-285-0075
Dallas
Microchip Technology Inc.
4570 Westgrove Drive, Suite 160
Addison, TX 75248
Microchip Technology Inc.
India Liaison Office
No. 6, Legacy, Convent Road
Bangalore 560 025, India
Tel: 91-80-229-0061 Fax: 91-80-229-0062
Tel: 972-818-7423 Fax: 972-818-2924
Dayton
Microchip Technology Inc.
Two Prestige Place, Suite 150
Miamisburg, OH 45342
Tel: 937-291-1654 Fax: 937-291-9175
Detroit
Microchip Technology Inc.
Tri-Atria Office Building
32255 Northwestern Highway, Suite 190
Farmington Hills, MI 48334
Tel: 248-538-2250 Fax: 248-538-2260
Japan
France
Microchip Technology Intl. Inc.
Benex S-1 6F
Arizona Microchip Technology SARL
Parc d’Activite du Moulin de Massy
43 Rue du Saule Trapu
3-18-20, Shinyokohama
Kohoku-Ku, Yokohama-shi
Kanagawa 222-0033 Japan
Tel: 81-45-471- 6166 Fax: 81-45-471-6122
Batiment A - ler Etage
91300 Massy, France
Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79
Germany
Arizona Microchip Technology GmbH
Gustav-Heinemann-Ring 125
D-81739 München, Germany
Tel: 49-89-627-144 0 Fax: 49-89-627-144-44
Korea
Microchip Technology Korea
168-1, Youngbo Bldg. 3 Floor
Samsung-Dong, Kangnam-Ku
Seoul, Korea
Tel: 82-2-554-7200 Fax: 82-2-558-5934
Shanghai
Microchip Technology
RM 406 Shanghai Golden Bridge Bldg.
2077 Yan’an Road West, Hong Qiao District
Shanghai, PRC 200335
Italy
Los Angeles
Arizona Microchip Technology SRL
Centro Direzionale Colleoni
Palazzo Taurus 1 V. Le Colleoni 1
20041 Agrate Brianza
Microchip Technology Inc.
18201 Von Karman, Suite 1090
Irvine, CA 92612
Tel: 949-263-1888 Fax: 949-263-1338
New York
Microchip Technology Inc.
150 Motor Parkway, Suite 202
Hauppauge, NY 11788
Tel: 631-273-5305 Fax: 631-273-5335
Milan, Italy
Tel: 39-039-65791-1 Fax: 39-039-6899883
Tel: 86-21-6275-5700 Fax: 86 21-6275-5060
11/15/99
San Jose
Microchip received QS-9000 quality system
certification for its worldwide headquarters,
design and wafer fabrication facilities in
Chandler and Tempe, Arizona in July 1999. The
Company’s quality system processes and
procedures are QS-9000 compliant for its
PICmicro® 8-bit MCUs, KEELOQ® code hopping
devices, Serial EEPROMs and microperipheral
products. In addition, Microchip’s quality
system for the design and manufacture of
development systems is ISO 9001 certified.
Microchip Technology Inc.
2107 North First Street, Suite 590
San Jose, CA 95131
Tel: 408-436-7950 Fax: 408-436-7955
All rights reserved. © 1999 Microchip Technology Incorporated. Printed in the USA. 11/99
Printed on recycled paper.
Information contained in this publication regarding device applications and the like is intended for suggestion only and may be superseded by updates. No representation or warranty is given and no liability is assumed
by Microchip Technology Incorporated with respect to the accuracy or use of such information, or infringement of patents or other intellectual property rights arising from such use or otherwise. Use of Microchip’s products
as critical components in life support systems is not authorized except with express written approval by Microchip. No licenses are conveyed, implicitly or otherwise, under any intellectual property rights. The Microchip
logo and name are registered trademarks of Microchip Technology Inc. in the U.S.A. and other countries. All rights reserved. All other trademarks mentioned herein are the property of their respective companies.
1999 Microchip Technology Inc.
Powered by ICminer.com Electronic-Library Service CopyRight 2003
相关型号:
![](http://pdffile.icpdf.com/pdf2/p00275/img/page/24AA02-I-SNG_1645900_files/24AA02-I-SNG_1645900_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00275/img/page/24AA02-I-SNG_1645900_files/24AA02-I-SNG_1645900_2.jpg)
24AA02-I/SNG
256 X 8 I2C/2-WIRE SERIAL EEPROM, PDSO8, 3.90 MM, ROHS COMPLIANT, PLASTIC, SOIC-8
MICROCHIP
![](http://pdffile.icpdf.com/pdf2/p00289/img/page/24AA00-C-SNG_1752625_files/24AA00-C-SNG_1752625_1.jpg)
![](http://pdffile.icpdf.com/pdf2/p00289/img/page/24AA00-C-SNG_1752625_files/24AA00-C-SNG_1752625_2.jpg)
24AA024-I/MCG
256 X 8 I2C/2-WIRE SERIAL EEPROM, PDSO8, 2 X 3 MM, 0.90 MM HEIGHT, LEAD FREE, PLASTIC, MO-229, DFN-8
MICROCHIP
©2020 ICPDF网 联系我们和版权申明