AFL12005DX/ES [ETC]
DC to DC Converter ; 直流到直流转换器\n型号: | AFL12005DX/ES |
厂家: | ETC |
描述: | DC to DC Converter
|
文件: | 总10页 (文件大小:121K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
PD - 94463B
AFL120XXD SERIES
120V Input, Dual Output
ADVANCED ANALOG
HIGH RELIABILITY
HYBRID DC/DC CONVERTERS
Description
The AFL Series of DC/DC converters feature high power
density with no derating over the full military tempera-
ture range. This series is offered as part of a complete
family of converters providing single and dual output
voltages and operating from nominal +28 or +270 volt
inputs with output power ranging from 80 to 120 watts.
For applications requiring higher output power, indi-
vidual converters can be operated in parallel. The inter-
nal current sharing circuits assure equal current distri-
bution among the paralleled converters. This series in-
corporates Advanced Analog’s proprietary magnetic
pulse feedback technology providing optimum dynamic
line and load regulation response. This feedback sys-
tem samples the output voltage at the pulse width modu-
lator fixed clock frequency, nominally 550 KHz. Multiple
converters can be synchronized to a system clock in the
500 KHz to 700 KHz range or to the synchronization
output of one converter. Undervoltage lockout, primary
and secondary referenced inhibit, soft-start and load
fault protection are provided on all models.
AFL
Features
n 80 To 160 Volt Input Range
±5, ±12, and ±15 Volts Outputs Available
n
3
n High Power Density - up to 70 W / in
n Up To 100 Watt Output Power
n Parallel Operation with Power Sharing
n Low Profile (0.380") Seam Welded Package
n Ceramic Feedthru Copper Core Pins
n High Efficiency - to 87%
n Full Military Temperature Range
n Continuous Short Circuit and Overload
Protection
n Output Voltage Trim
n Primary and Secondary Referenced
Inhibit Functions
n Line Rejection > 50 dB - DC to 50KHz
n External Synchronization Port
n Fault Tolerant Design
n Single Output Versions Available
n Standard Military Drawings Available
These converters are hermetically packaged in two en-
closure variations, utilizing copper core pins to mini-
mize resistive DC losses. Three lead styles are avail-
able, each fabricated with Advanced Analog’s rugged
ceramic lead-to-package seal assuring long term
hermeticity in the most harsh environments.
Manufactured in a facility fully qualified to MIL-PRF-
38534, these converters are available in four screening
grades to satisfy a wide range of requirements. The CH
grade is fully compliant to the requirements of MIL-H-
38534 for class H. The HB grade is processed and
screened to the class H requirement, but may not nec-
essarily meet all of the other MIL-PRF-38534 require-
ments, e.g., element evaluation and Periodic Inspection
(P.I.) not required. Both grades are tested to meet the
complete group “A” test specification over the full mili-
tary temperature range without output power deration.
Two grades with more limited screening are also avail-
able for use in less demanding applications. Varia-
tions in electrical, mechanical and screening can
be accommodated. Contact Advanced Analog for
special requirements.
www.irf.com
1
09/10/02
AFL120XXD Series
Specifications
ABSOLUTE MAXIMUM RATINGS
Input Voltage
-0.5V to 180V
Soldering Temperature
Case Temperature
300°C for 10 seconds
Operating
Storage
-55°C to +125°C
-65°C to +135°C
Static Characteristics -55°C < TCASE < +125°C, 80V< VIN < 160V unless otherwise specified.
Group A
Parameter
INPUT VOLTAGE
Subgroups
Test Conditions
Min
Nom
Max
Unit
Note 6
80
120
160
V
OUTPUT VOLTAGE
V
IN
= 120 Volts, 100% Load
AFL12005D
AFL12012D
AFL12015D
AFL12005D
AFL12012D
AFL12015D
1
1
4.95
-5.05
5.00
-5.00
5.05
-4.95
V
V
Positive Output
Negative Output
1
1
Positive Output
Negative Output
11.88
-12.12
12.00
-12.00
12.12
-11.88
V
V
Positive Output
Negative Output
1
1
14.85
-15.15
15.00
-15.00
15.15
-14.85
V
V
Positive Output
Negative Output
2, 3
2, 3
4.90
-5.10
5.10
-4.90
V
V
Positive Output
Negative Output
2, 3
2, 3
11.76
-12.24
12.24
-11.76
V
V
Positive Output
Negative Output
2, 3
2, 3
14.70
-15.30
15.30
-14.70
V
V
OUTPUT CURRENT
OUTPUT POWER
V
IN
= 80, 120, 160 Volts - Notes 6, 11
Either Output
AFL12005D
AFL12012D
AFL12015D
12.8
6.4
A
A
A
Either Output
Either Output
5.3
Total of Both Outputs. Notes 6,11
AFL12005D
AFL12012D
AFL12015D
80
96
W
W
W
100
MAXIMUM CAPACITIVE LOAD
Each Output Note 1
=120 Volts, 100% Load –Notes 1, 6
10,000
-0.015
µfd
V
OUTPUT VOLTAGE
TEMPERATURE COEFFICIENT
IN
+0.015
%/°C
OUTPUT VOLTAGE REGULATION
Note 10
-0.5
-1.0
+0.5
+1.0
%
%
Line
1, 2, 3
1, 2, 3
No Load, 50% Load, 100% Load
Load
V
= 80, 120, 160 Volts.
IN
Cross
V
= 80, 120, 160 Volts. Note 12
IN
AFL12005D
1, 2, 3
1, 2, 3
1, 2, 3
Positive Output
Negative Output
-1.0
-8.0
+1.0
+8.0
%
%
AFL12012D
AFL12015D
Positive Output
Negative Output
-1.0
-5.0
+1.0
+5.0
%
%
Positive Output
Negative Output
-1.0
-5.0
+1.0
+5.0
%
%
For Notes to Specifications, refer to page 4
2
www.irf.com
AFL120XXD Series
Static Characteristics (Continued)
Group A
Parameter
Subgroups
Test Conditions
Min
Nom
Max
Unit
OUTPUT RIPPLE VOLTAGE
V
= 80, 120, 160 Volts, 100% Load,
IN
BW = 10MHz
AFL12005D
1, 2, 3
1, 2, 3
1, 2, 3
60
80
80
mV
mV
mV
pp
pp
pp
AFL12012D
AFL12015D
V
= 120 Volts
INPUT CURRENT
IN
1
2, 3
1, 2, 3
1, 2, 3
20
25
3
mA
No Load
I
= 0
OUT
mA
mA
mA
Inhibit 1
Inhibit 2
Pin 4 Shorted to Pin 2
Pin 12 Shorted to Pin 8
5
INPUT RIPPLE CURRENT
AFL12005D
V
= 120 Volts, 100% Load
IN
1, 2, 3
1, 2, 3
1, 2, 3
60
70
80
mA
pp
pp
pp
AFL12012D
AFL12015D
mA
mA
V
= 90% V
, Current split
NOM
CURRENT LIMIT POINT
OUT
equally on positive and negative outputs.
Note 5
1
2
3
115
105
125
125
115
140
%
%
%
Expressed as a Percentage
of Full Rated Load
LOAD FAULT POWER DISSIPATION
V
V
IN = 120 Volts
1, 2, 3
32
W
Overload or Short Circuit
EFFICIENCY
AFL12005D
AFL12012D
AFL12015D
IN = 120 Volts, 100% Load
1, 2, 3
1, 2, 3
1, 2, 3
78
82
83
82
85
87
%
%
%
ENABLE INPUTS (Inhibit Function)
Converter Off
1, 2, 3
1, 2, 3
Logical Low on Pin 4 or Pin 12
Note 1
Logical High on Pin 4 and Pin 12 - Note 9
Note 1
-0.5
2.0
0.8
100
50
V
µ
A
V
µA
Sink Current
Converter On
Sink Current
100
1, 2, 3
500
550
600
KHz
SWITCHING FREQUENCY
SYNCHRONIZATION INPUT
Frequency Range
1, 2, 3
1, 2, 3
1, 2, 3
500
2.0
-0.5
700
10
0.8
100
80
KHz
V
V
nSec
%
Pulse Amplitude, Hi
Pulse Amplitude, Lo
Pulse Rise Time
Note 1
Note 1
20
Pulse Duty Cycle
ISOLATION
1
Input to Output or Any Pin to Case
(except Pin 3). Test @ 500VDC
100
MΩ
DEVICE WEIGHT
MTBF
Slight Variations with Case Style
85
gms
MIL-HDBK-217F, AIF @ T = 40°C
C
300
KHrs
For Notes to Specifications, refer to page 4
www.irf.com
3
AFL120XXD Series
Dynamic Characteristics -55°C < TCASE < +125°C, VIN=120V unless otherwise specified.
Group A
Parameter
Subgroups
Test Conditions
Min
Nom
Max
Unit
LOAD TRANSIENT RESPONSE
Note 2, 8
AFL12005D
Either Output
Amplitude
Recovery
4, 5, 6
4, 5, 6
Load Step 50%
100%
-450
-450
450
200
mV
µSec
4, 5, 6
4, 5, 6
Load Step 10%
50%
50%
10%
450
200
400
mV
µSec
µSec
Amplitude
Recovery
10%
50%
4, 5, 6
4, 5, 6
Load Step 50%
100%
-750
-750
750
200
mV
µSec
AFL12012D
Either Output
Amplitude
Recovery
Amplitude
Recovery
4, 5, 6
4, 5, 6
Load Step 10%
50%
50%
10%
750
200
400
mV
µSec
µSec
10%
50%
4, 5, 6
4, 5, 6
Load Step 50%
100%
-750
-750
750
200
mV
µSec
AFL12015D
Either Output
Amplitude
Recovery
4, 5, 6
4, 5, 6
Load Step 10%
50%
50%
10%
750
200
400
mV
µSec
µSec
Amplitude
Recovery
10%
50%
Note 1, 2, 3
LINE TRANSIENT RESPONSE
V
Step = 80
160 Volts
-500
500
500
mV
µSec
Amplitude
Recovery
IN
TURN-ON CHARACTERISTICS
Note 4
Overshoot
Delay
4, 5, 6
4, 5, 6
Enable 1, 2 on. (Pins 4, 12 high or
open)
250
120
mV
mSec
50
50
75
60
LOAD FAULT RECOVERY
LINE REJECTION
Same as Turn On Characteristics.
MIL-STD-461D, CS101, 30Hz to 50KHz
Note 1
dB
Notes to Specifications:
1. Parameters not 100% tested but are guaranteed to the limits specified in the table.
2. Recovery time is measured from the initiation of the transient to where V
at 50% load.
has returned to within ±1% of V
out
out
3. Line transient transition time ≥ 100 µSec.
4. Turn-on delay is measured with an input voltage rise time of between 100 and 500 volts per millisecond.
5. Current limit point is that condition of excess load causing output voltage to drop to 90% of nominal.
6. Parameter verified as part of another test.
7. All electrical tests are performed with the remote sense leads connected to the output leads at the load.
8. Load transient transition time ≥ 10 µSec.
9. Enable inputs internally pulled high. Nominal open circuit voltage ≈ 4.0VDC.
10. Load current split equally between +V
out
and -V .
out
11. Output load must be distributed so that a minimum of 20% of the total output power is being provided by one of
the outputs.
12. Cross regulation measured with load on tested output at 20% of maximum load while changing the load on
other output from 20% to 80%.
4
www.irf.com
AFL120XXD Series
AFL120XXD Circuit Description
Figure I. AFL Dual Output Block Diagram
Input
Filter
Output
Filter
1
4
+ Output
DC Input
Enable 1
7
Current
Sense
Primary
Bias Supply
Output Return
-Output
8
9
Output
Filter
Sync Output
5
Share
Amplifier
Control
Share
11
Error
Amp
& Ref
Sync Input
Case
6
3
2
12 Enable 2
Trim
10
Input Return
Although incorporating several sophisticated and useful
ancilliary features, basic operation of the AFL120XXDseries
can be initiated by simply applying an input voltage to pins 1
and 2 and connecting the appropriate loads between pins 7,
8, and 9. Of course, operation of any converter with high
power density should not be attempted before secure at-
tachment to an appropriate heat dissipator. (See Thermal
Considerations, page 7)
Circuit Operation and Application Information
The AFL series of converters employ a forward switched
mode converter topology. (refer to Figure I.) Operation of
the device is initiated when a DC voltage whose magnitude
is within the specified input limits is applied between pins 1
and 2. If pins 4 and 12 are enabled (at a logical 1 or open)
the primary bias supply will begin generating a regulated
housekeeping voltage bringing the circuitry on the primary
side of the converter to life. Two power MOSFETs used to Inhibiting Converter Output
chop the DC input voltage into a high frequency square
As an alternative to application and removal of the DC volt-
wave, apply this chopped voltage to the power transformer.
As this switching is initiated, a voltage is impressed on a
second winding of the power transformer which is then
rectified and applied to the primary bias supply. When this
occurs, the input voltage is excluded from the bias voltage
generator and the primary bias voltage becomes internally
generated.
age to the input, the user can control the converter output
by providing TTL compatible, positive logic signals to either
of two enable pins (pin 4 or 12). The distinction between
these two signal ports is that enable 1 (pin 4) is referenced
to the input return (pin 2) while enable 2 (pin 12) is refer-
enced to the output return (pin 8). Thus, the user has
access to an inhibit function on either side of the isolation
barrier. Each port is internally pulled “high” so that when not
used, an open connection on both enable pins permits nor-
mal converter operation. When their use is desired, a logi-
cal “low” on either port will shut the converter down.
The switched voltage impressed on the secondary output
transformer windings is rectified and filtered to provide the
positive and negative converter output voltages. An error
amplifier on the secondary side compares the positive out-
put voltage to a precision reference and generates an error
signal proportional to the difference. This error signal is
magnetically coupled through the feedback transformer into
the control section of the converter varying the pulse width
of the square wave signal driving the MOSFETs, narrowing
the pulse width if the output voltage is too high and widening
it if it is too low. These pulse width variations provide the
necessary corrections to regulate the magnitude of output
voltage within its’ specified limits.
Figure II. Enable Input Equivalent Circuit
+5.6V
100K
1N4148
Pin 4 or
Pin 12
Disable
290K
2N3904
Because the primary portion of the circuit is coupled to the
secondary side with magnetic elements, full isolation from
input to output is maintained.
150K
Pin 2 or
Pin 8
www.irf.com
5
AFL120XXD Series
Internally, these ports differ slightly in their function. In use,
a low on Enable 1 completely shuts down all circuits in the
converter, while a low on Enable 2 shuts down the second-
ary side while altering the controller duty cycle to near zero.
Externally, the use of either port is transparent to the user
save for minor differences in idle current. (See specification
table).
level of +2.0 volts. The sync output of another converter
which has been designated as the master oscillator pro-
vides a convenient frequency source for this mode of op-
eration. When external synchronization is not indicted, the
sync in pin should be left unconnected thereby permitting
the converter to operate at its’ own internally set frequency.
The sync output signal is a continuous pulse train set at
550 ±50 KHz, with a duty cycle of 15 ±5%. This signal is
referenced to the input return and has been tailored to be
compatible with the AFL sync input port. Transition times
are less than 100 ns and the low level output impedance is
less than 50 ohms. This signal is active when the DC input
voltage is within the specified operating range and the con-
verter is not inhibited. This synch output has adequate
drive reserve to synchronize at least five additional con-
verters. A typical synchronization connection option is il-
lustrated in Figure III.
Synchronization of Multiple Converters
When operating multiple converters, system requirements
often dictate operation of the converters at a common fre-
quency. To accommodate this requirement, the AFL series
converters provide both a synchronization input and out-
put.
The sync input port permits synchronization of an AFL co-
nverter to any compatible external frequency source oper-
ating between 500 and 700 KHz. This input signal should
be referenced to the input return and have a 10% to 90%
duty cycle. Compatibility requires transition times less th an
100 ns, maximum low level of +0.8 volts and a minimum high
Figure III. Preferred Connection for Parallel Operation
1
12
Enable
2
Power
Input
Vin
Rtn
Share
Trim
Case
Enable
AFL
AFL
1
-
Output
Return
Output
Sync Out
Sync In
+
7
6
1
Optional
Synchronization
Connection
Share Bus
12
Enable
2
Vin
Rtn
Share
Trim
Case
Enable
1
-
Output
Return
Output
to Negative Load
to Positive Load
Sync Out
Sync In
+
7
6
1
12
Enable
2
Vin
Rtn
Share
Trim
Case
AFL
Enable
1
-
Output
Return
Output
Sync Out
Sync In
+
6
7
(Other Converters)
Parallel Operation-Current and Stress Sharing
ture of the AFL series operating in the parallel mode is that
in addition to sharing the current, the stress induced by
temperature will also be shared. Thus if one member of a
paralleled set is operating at a higher case temperature, the
current it provides to the load will be reduced as compensa-
tion for the temperature induced stress on that device.
Figure III. illustrates the preferred connection scheme for
operation of a set of AFL converters with outputs operating
in parallel. Use of this connection permits equal current shar-
ing among the members of a set whose load current ex-
ceeds the capacity of an individual AFL. An important fea-
6
www.irf.com
AFL120XXD Series
When operating in the shared mode, it is important that A conservative aid to estimating the total heat sink surface
symmetry of connection be maintained as an assurance of area (AHEAT SINK) required to set the maximum case temp-
optimum load sharing performance. Thus, converter out- erature rise (∆T) above ambient temperature is given by
puts should be connected to the load with equal lengths of the following expression:
wire of the same gauge and should be connected to a com-
mon physical point, preferably at the load along with the
−1.43
∆T
converter output and return leads. All converters in a par-
alleled set must have their share pins connected together.
This arrangement is diagrammatically illustrated in Figure
III. showing the output and return pins connected at a star
point which is located close as possible to the load.
A
HEAT SINK
≈
− 3.0
0.85
80P
where
∆T = Case temperature rise above ambient
As a consequence of the topology utilized in the current
sharing circuit, the share pin may be used for other func-
tions. In applications requiring only a single converter, the
voltage appearing on the share pin may be used as a “totall
current monitor”. The share pin open circuit voltage is nomi-
nally +1.00v at no load and increases linearly with increas-
ing total output current to +2.20v at full load. Note that the
current we refer to here is the total output current, that is,
the sum of the positive and negative outout currents.
1
P = Device dissipation in Watts = POUT
Eff
−1
As an example, assume that it is desired to operate an
AFL12015D while holding the case temperature at TC
+85°C in an area where the ambient temperature is held to
≤
a constant +25°C; then
∆T = 85 - 25 = 60°C
Thermal Considerations
Because of the incorporation of many innovative techno-
logical concepts, the AFL series of converters is capable of
providing very high output power from a package of very
small volume. These magnitudes of power density can only
be obtained by combining high circuit efficiency with effec-
tive methods of heat removal from the die junctions. This
requirement has been effectively addressed inside the de-
vice; but when operating at maximum loads, a significant
amount of heat will be generated and this heat must be
conducted away from the case. To maintain the case tem-
perature at or below the specified maximum of 125°C, this
heat must be transferred by conduction to an appropriate
heat dissipater held in intimate contact with the converter
base-plate.
From the Specification Table, the worst case full load effi-
ciency for this device is 83% @ 100 watts: thus, power
dissipation at full load is given by
1
P = 100•
−1 = 100• 0.205 = 20.5W
(
)
.83
and the required heat sink area is
1.43
−
60
A
HEAT SINK
=
− 3.0 = 56.3 in2
80• 20.50.85
Since the effectiveness of this heat transfer is dependent
on the intimacy of the baseplate/heatsink interface, it is
strongly recommended that a high thermal conductivity heat
transferring medium is inserted between the baseplate and
heatsink. The material most frequently utilized at the fac-
tory during all testing and burn-in processes is sold under
Thus, a total heat sink surface area (including fins, if any) of
2
56 in in this example, would limit case rise to 60°C above
ambient. A flat aluminum plate, 0.25" thick and of approxi-
2
mate dimension 4" by 7" (28 in per side) would suffice for
1
the trade name of Sil-Pad 400 . This particular product is
this application in a still air environment. Note that to meet
the criteria in this example, both sides of the plate require
unrestricted exposure to the +25°C ambient air.
an insulator but electrically conductive versions are also
available. Use of these materials assures maximum sur-
face contact with the heat dissipater thereby compensating
for any minor surface variations. While other available types
of heat conductive materials and thermal compounds pro-
vide similar effectiveness, these alternatives are often less
convenient and can be somewhat messy to use.
1
Sil-Pad is a registered Trade Mark of Bergquist, Minneapolis, MN
www.irf.com
7
AFL120XXD Series
Input Filter
Table 1. Output Voltage Trim Values and Limits
The AFL120XXD series converters incorporate a single
stage LC input filter whose elements dominate the input
load impedance characteristic during the turn-on sequence.
The input circuit is as shown in Figure IV.
AFL12005D
AFL12012D
AFL12015D
Vout
Radj
Vout
Radj
Vout
Radj
5.5
5.4
0
12.5
12.4
12.3
12.2
12.1
12.0
11.7
11.3
10.8
10.6
10.417
0
15.5
15.4
15.3
15.2
15.1
15.0
14.6
14.0
13.5
13.0
12.917
0
Figure IV. Input Filter Circuit
12.5K
33.3K
75K
200K
∞
47.5K
127K
285K
760K
∞
62.5K
167K
375K
1.0M
∞
5.3
16.8uH
5.2
5.1
Pin 1
5.0
4.9
190K
65K
23K
2.5K
0
975K
288K
72.9K
29.9K
0
1.2M
325K
117K
12.5K
0
0.78uF
4.8
4.7
Pin 2
4.6
4.583
Note that the nominal magnitude of output voltage resides in
the middle of the table and the corresponding resistor value
is set to ∞. To set the magnitude greater than nominal, the
adjust resistor is connected to output return. To set the
magnitude less than nominal, the adjust resistor is con-
nected to the positive output. (Refer to Figure V.)
Undervoltage Lockout
A minimum voltage is required at the input of the converter
to initiate operation. This voltage is set to 74 ± 4 volts. To
preclude the possibility of noise or other variations at the
input falsely initiating and halting converter operation, a hys-
teresis of approximately 7 volts is incorporated in this cir-
cuit. Thus if the input voltage droops to 67 ± 4 volts, the
converter will shut down and remain inoperative until the
input voltage returns to ≈ 74 volts.
For output voltage settings that are within the limits, but
between those listed in Table I, it is suggested that the
resistor values be determined empirically by selection or by
use of a variable resistor. The value thus determined can
then be replaced with a good quality fixed resistor for per-
manent installation.
OutputVoltage Adjust
By use of the trim pin (10), the magnitude of output voltages
can be adjusted over a limited range in either a positive or
negative direction. Connecting a resistor between the trim
pin and either the output return or the positive output will
raise or lower the magnitude of output voltages. The span
of output voltage adjustment is restricted to the limits shown
When use of this adjust feature is elected, the user should
be aware that the temperature performance of the con-
verter output voltage will be affected by the temperature
performance of the resistor selected as the adjustment
element and therefore, is advised to employ resistors with a
tight temperature coefficient of resistance.
in Table I.
Figure V. Connection for VOUT Adjustment
12
Enable 2
Share
RADJ
+ Sense
AFL120xxD
- Sense
To
Return
Loads
+ V
out
7
Connect Radj to + to increase, - to decrease
8
www.irf.com
AFL120XXD Series
AFL120XXD Case Outlines
Case X
Case W
Pin Variation of Case Y
3.000
2.760
ø
0.128
0.050
0.050
0.250
0.250
1.000
1.000
Ref
1.260 1.500
0.200 Typ
Non-cum
Pin
ø
0.040
Pin
0.040
0.220
ø
2.500
0.220
0.525
2.800
2.975 max
0.238 max
0.42
0.380
Max
0.380
Max
Case Y
Case Z
Pin Variation of Case Y
1.150
0.300
ø
0.140
0.25 typ
0.050
0.050
0.250
0.250
1.000
Ref
1.500 1.750 2.00
1.000
Ref
0.200 Typ
Non-cum
Pin
ø
0.040
Pin
ø
0.040
0.220
0.220
1.750
2.500
0.375
0.36
2.800
2.975 max
0.525
0.238 max
0.380
Max
0.380
Max
Tolerances, unless otherwise specified: .XX
.XXX
=
=
±0.010
±0.005
BERYLLIAWARNING: These converters are hermetically sealed;however they contain BeO substrates and should not be ground or subjected to any other
operations including exposure to acids, which may produce Beryllium dust or fumes containing Beryllium
www.irf.com
9
AFL120XXD Series
Available Screening Levels and ProcessVariations for AFL120XXD Series.
MIL-STD-883
Method
No
ES
HB
CH
Requirement
Temperature Range
Element Evaluation
Internal Visual
Suffix
Suffix
Suffix
Suffix
-20°C to +85°C
-55°C to +125°C
-55°C to +125°C
-55°C to +125°C
MIL-PRF-38534
Yes
2017
1010
¬
Yes
Cond B
500g
Yes
Cond C
Temperature Cycle
Constant Acceleration
Burn-in
Cond C
2001
Cond A
Cond A
1015
48hrs @ 85°C
48hrs @ 125°C
25°C
160hrs @ 125°C
160hrs @ 125°C
Final Electrical (Group A)
Seal, Fine & Gross
External Visual
MIL-PRF-38534
1014
25°C
¬
-55, +25, +125°C -55, +25, +125°C
Cond A, C
Yes
Cond A, C
Yes
Cond A, C
Yes
2009
¬
*per Commercial Standards
Part Numbering
AFL120XXD Pin Designation
AFL 120 05 D X / CH
Pin No.
Designation
Positive Input
Input Return
Case
Model
Input Voltage
Screening
–
1
2
, ES
HB, CH
Case Style
W, X, Y, Z
28= 28 V, 50= 50 V
120=120 V, 270= 270 V
3
Output Voltage
05= 5 V, 12= 12 V,
15= 15 V
Outputs
S = Single
D = Dual
4
Enable 1
5
Sync Output
Sync Input
AFL120XXD to Standard Military Drawing Equivalence Table
AFL12012D 5962-9960901
6
7
Positive Output
Output Return
Negative Output
Output Voltage Trim
Share
8
9
10
11
12
Enable 2
WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, Tel: (310) 322 3331
ADVANCED ANALOG: 2270 Martin Av., Santa Clara, California 95050, Tel: (408) 727-0500
Visit us at www.irf.com for sales contact information.
Data and specifications subject to change without notice. 09/02
10
www.irf.com
相关型号:
AFL12005DX/ESPBF
DC-DC Regulated Power Supply Module, 2 Output, 80W, Hybrid, 0.380 INCH, LOW PROFILE, SEAM WELDED PACKAGE-12
INFINEON
AFL12005DX/HBPBF
DC-DC Regulated Power Supply Module, 2 Output, 80W, Hybrid, 0.380 INCH, LOW PROFILE, SEAM WELDED PACKAGE-12
INFINEON
AFL12005DXPBF
DC-DC Regulated Power Supply Module, 2 Output, 80W, Hybrid, 0.380 INCH, LOW PROFILE, SEAM WELDED PACKAGE-12
INFINEON
AFL12005DY/CHPBF
DC-DC Regulated Power Supply Module, 2 Output, 80W, Hybrid, 0.380 INCH, LOW PROFILE, SEAM WELDED PACKAGE-12
INFINEON
©2020 ICPDF网 联系我们和版权申明