AMC-136 [ETC]
High Perfomance Amplifiers， 20 dB Gain 5200 MHz ; 选择高速放大器20 dB的增益5200兆赫\n
| 型号： | AMC-136 |
| 厂家： | 
ETC |
| 描述： | High Perfomance Amplifiers， 20 dB Gain 5200 MHz
|
| 文件： | 总2页 (文件大小：79K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
AM-/AMC-136
High Performance Amplifier, 20 dB Gain
10 - 200 MHz
Features
FP-9
•
•
•
+49 dBm Typical Midband Third Order Intercept
+29 dBm Typical Midband 1 dB Compression
4.8 dB Typical Midband Noise Figure
Description
M/A-COM’s AM-136 is a coupler feedback amplifier with high
intercept and compression points. The use of coupler feedback
minimizes noise figure and current in a high intercept amplifier.
This amplifier is packaged in a flatpack with flanges. Due to the
metal flatpack the thermal rise minimized. The ground plane on
the PC board should be configured to remove heat from under the
package. AM-136 is ideally suited for use where a high intercept,
high reliability amplifier is required.
Ordering Information
Part Number
AM-136 PIN
AMC-136 SMA
Package
Flatpack
Connectorized
C-25
Absolute Maximum Ratings 1
Parameter
Max. Input Power
Vbias
Absolute Maximum
+15 dBm
+17.0 V
Operating Temperature
Storage Temperature
-55°C to +85°C
-65°C to +125°C
1. Operation of this device above any one of these parameters may
cause permanent damange.
Pin Configuration
Pin #
Function
Pin #
Function
1
2
3
4
5
RF OUT
GND
6
7
RF IN
GND
GND
8
GND
GND
Vbias2
9
GND
Vbias2
10
2. Bias may be applied to either a single bias pin, or both bias pins.
If bias is applied to both bias pins, it is important that potential
ground loops be avoided, and that there is adequate filtering on
the bias lines.
V 4.0
Specifications subject to change without notice.
ꢀ North America: Tel. (800) 366-2266, Fax (800) 618-8883
ꢀ Asia/Pacific: Tel.+81-44-844-8296, Fax +81-44-844-8298
ꢀ Europe: Tel. +44 (1344) 869 595, Fax+44 (1344) 300 020
Visit www.macom.com for additional data sheets and product information.
High Performance Amplifier, 20 dB Gain, 10 - 200 MHz
AM-/AMC-136
Electrical Specifications3,4 TA = -55°C to +85°C Case Temperature
Parameter
Test Conditions
Frequency
Units
Min
Typical
Max
Gain
50 MHz @ +25°C
50 MHz
dB
dB
dB
19.2
—
20.4
—
20.8
±0.8
±1.0
Frequency Response
—
—
10 - 200 MHz
10 - 200 MHz
Gain Variation with
Temperature
—
—
1 dB Compression
Output Power
10 - 200 MHz
10 - 70 MHz
dBm
dBm
+23
+25
—
—
—
—
Noise Figure
Reverse Transmission
VSWR
—
—
—
10 - 200 MHz
10 - 200 MHz
dB
dB
—
—
—
7.0
-26
-28
10 - 200 MHz
10 - 70 MHz
Ratio
Ratio
—
—
—
—
2.5:1
1.7:1
Output IP2
Output IP3
Two-tone inputs up to +10 dBm
Two-tone inputs up to +10 dBm
10 - 200 MHz
10 - 70 MHz
dBm
dBm
+53
+57
—
—
—
—
10 - 200 MHz
10 - 70 MHz
dBm
dBm
+36
+44
—
—
—
—
Vbias
Ibias
—
—
—
V
14.25
—
15
15.75
220
2.7W Typical
mA
180
3. All specifications apply when operated at +15 VDC, with 50 ohms source and load impedance.
4. Heat Sinking: Operation at case temperature above 95°C is not recommended. Heat sinking adequate to dissipate 2.7W must be provided in use.
The flange should be screwed down to the heat sink, which should be RF ground.
Typical Performance
Gain vs. Frequency
VSWR vs. Frequency
RF IN
85°C
25°C
-55°C
RF OUT
22.0
21.0
20.0
19.0
2.50
2.00
1.50
1.00
3
5
10
20
50
100
200
300
3
5
10
20
50
100 200 300
Frequency (MHz)
Frequency (MHz)
Intermodulation Intercept
IP3 IP2
Noise Figure and 1 dB Compression
Output Pow er
Noise Figure
6.0
32
72
52
48
44
40
5.5
5.0
4.5
30
28
26
68
64
60
3
5
10 20
50 100 200 300
3
5
10 20 50 100 200 300
Frequency (MHz)
Frequency (MHz)
V 4.0
Specifications subject to change without notice.
ꢀ North America: Tel. (800) 366-2266, Fax (800) 618-8883
ꢀ Asia/Pacific: Tel.+81-44-844-8296, Fax +81-44-844-8298
ꢀ Europe: Tel. +44 (1344) 869 595, Fax+44 (1344) 300 020
Visit www.macom.com for additional data sheets and product information.
相关型号：
©2020 ICPDF网 联系我们和版权申明