AN78M09NSP [ETC]
Analog IC ; 模拟IC\n
| 型号： | AN78M09NSP |
| 厂家： | 
ETC |
| 描述： | Analog IC
|
| 文件： | 总11页 (文件大小：167K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Voltage Regulators
AN78MxxNSP Series
3-pin positive output voltage regulator (500 mA type)
I Overview
Unit: mm
6.50±0.20
5.30±0.10
The AN78MxxNSP series is a 3-pin fixed positive
(4.35)
output type monolithic voltage regulator housed in surface
(3.00)
1.00±0.20
mounting package. Stabilized fixed output voltage is ob-
tained from unstable DC input voltage with using mini-
mum external components. 9 types of fixed output volt-
age are available; 5 V, 6 V, 7 V, 8 V, 9 V, 10 V, 12 V, 15
V and 18 V. They can be used widely in power circuits
with current capacity up to 500 mA.
2
1
3
0.75±0.10
+0.10
2.30
I Features
0.55
–0.05
4.60±0.10
0.10±0.10
• Output voltage: 5V,6V,7V,8V,9V,10V,12V,15V,18 V
• Built-in overcurrent limit circuit
• Built-in thermal overload protection circuit
• Built-in ASO (area of safe operation) protection circuit
SP-3SU
I Block Diagram
Pass Tr
Current
source
Current
limitter
RSC
Voltage
Starter
reference
R2
R1
Thermal
protection
Error amp.
1
2
3
FIN
Input
CI
CO
Output
CI ≥ 0.33 µF, CO ≥ 0.1 µF
I Pin Descriptions
Pin No.
Description
1
2
3
Input
Input voltage pin
Ground pin (FIN)
Output voltage pin
GND
Output
1
AN78MxxNSP Series
Voltage Regulators
I Absolute Maximum Ratings
Parameter
Symbol
VCC
ICC
Range
35
Unit
V
2
Supply voltage *
3
Supply current *
mA
mW
°C
4
Power dissipation *
PD
1
Operating ambient temperature *
Topr
Tstg
−30 to +85
−55 to +150
1
Storage temperature *
°C
Note) 1. 1: Except for the operating ambient temperature and storage temperature, all ratings are for T = 25°C.
*
a
2: When VCC of 35 V is applied, the overvoltage protection of ASO protection circuit may shut off the output.
3: Since this IC has incorporated a current limiter, the current value does not exceed the rating.
4: When Tj exceeds 150°C (designed value), the internal circuit cuts off the output. Note that the relationship between IC
power dissipation and the ambient temperature must follow the derating curve.
*
*
*
2. This IC is not suitable for car electronics equipment.
I Electrical Characteristics at Ta = 25°C
•
AN78M05NSP (5 V type)
The specified condition Tj = 25°C means that the test should be carried out within so short a test time (within 10 ms)
that the characteristic value drift due to the chip junction temperature rise can be ignored.
Unless otherwise specified, VI = 10 V, IO = 350 mA, CI = 0.33 µF and CO = 0.1 µF
Parameter
Output voltage
Symbol
VO1
Conditions
Min
Typ Max
Unit
V
Tj = 25°C
4.8
5
5.2
Output voltage tolerance
VO2
VI = 7.5 V to 20 V, IO = 5 mA to 350 mA 4.75
Tj = 25°C
5.25
V
Line regulation 1
Line regulation 2
Load regulation 1
Load regulation 2
Bias current
REGIN1 VI = 7.5 V to 25 V, Tj = 25°C
REGIN2 VI = 8 V to 25 V, Tj = 25°C
REGL1 IO = 5 mA to 500 mA, Tj = 25°C
REGL2 IO = 5 mA to 200 mA, Tj = 25°C
3
100
50
mV
mV
mV
mV
mA
mA
mA
dB
1
20
10
4
100
50
IBias
Tj = 25°C
6
Bias current fluctuation to input ∆IBias(IN) VI = 8 V to 25 V, Tj = 25°C
Bias current fluctuation to load ∆IBias(L) IO = 5 mA to 350 mA, Tj = 25°C
0.8
0.5
Ripple rejection ratio
RR
VI = 8 V to 18 V, IO = 100 mA, f = 120 Hz 62
•
Design reference data
Note) The characteristics listed below are theoretical values based on the IC design and are not guaranteed.
Parameter
Output noise voltage
Symbol
Conditions
f = 10 Hz to 100 kHz
Min
Typ Max
Unit
µV
V
VNO
40
2
Minimum input/output voltage VDIF(min) IO = 500 mA, Tj = 25°C
difference
Output short-circuit current
Peak output current
IO(Short) VI = 35 V, Tj = 25°C
IO(Peak) Tj = 25°C
300
1000
− 0.5
mA
mA
Output voltage temperature
coefficient
∆VO / Ta IO = 5 mA, Tj = 0°C to 125°C
mV/°C
Thermal protection operating
temperature
Tj(TH) IO = 5 mA
150
°C
2
Voltage Regulators
AN78MxxNSP Series
I Electrical Characteristics at Ta = 25°C (continued)
•
AN78M06NSP (6 V type)
The specified condition Tj = 25°C means that the test should be carried out within so short a test time (within 10 ms)
that the characteristic value drift due to the chip junction temperature rise can be ignored.
Unless otherwise specified, VI = 11 V, IO = 350 mA, CI = 0.33 µF and CO = 0.1 µF
Parameter
Output voltage
Symbol
VO1
Conditions
Min
5.75
5.7
Typ Max
Unit
V
Tj = 25°C
6
6.25
6.3
Output voltage tolerance
VO2
VI = 8.5 V to 21 V, IO = 5 mA to 350 mA
Tj = 25°C
V
Line regulation 1
Line regulation 2
Load regulation 1
Load regulation 2
Bias current
REGIN1 VI = 8.5 V to 25 V, Tj = 25°C
REGIN2 VI = 9 V to 25 V, Tj = 25°C
REGL1 IO = 5 mA to 500 mA, Tj = 25°C
REGL2 IO = 5 mA to 200 mA, Tj = 25°C
5
1.5
20
10
4
100
50
mV
mV
mV
mV
mA
mA
mA
dB
120
60
IBias
Tj = 25°C
6
Bias current fluctuation to input ∆IBias(IN) VI = 9 V to 25 V, Tj = 25°C
Bias current fluctuation to load ∆IBias(L) IO = 5 mA to 350 mA, Tj = 25°C
0.8
0.5
Ripple rejection ratio
RR
VI = 9 V to 19 V, IO = 100 mA, f = 120 Hz 59
•
Design reference data
Note) The characteristics listed below are theoretical values based on the IC design and are not guaranteed.
Parameter
Output noise voltage
Symbol
Conditions
f = 10 Hz to 100 kHz
Min
Typ Max
Unit
µV
V
VNO
45
2
Minimum input/output voltage VDIF(min) IO = 500 mA, Tj = 25°C
difference
Output short-circuit current
Peak output current
IO(Short) VI = 35 V, Tj = 25°C
IO(Peak) Tj = 25°C
300
1000
− 0.5
mA
mA
Output voltage temperature
coefficient
∆VO / Ta IO = 5 mA, Tj = 0°C to 125°C
mV/°C
Thermal protection operating
temperature
Tj(TH) IO = 5 mA
150
°C
3
AN78MxxNSP Series
Voltage Regulators
I Electrical Characteristics at Ta = 25°C (continued)
•
AN78M07NSP (7 V type)
The specified condition Tj = 25°C means that the test should be carried out within so short a test time (within 10 ms)
that the characteristic value drift due to the chip junction temperature rise can be ignored.
Unless otherwise specified, VI = 12 V, IO = 350 mA, CI = 0.33 µF and CO = 0.1 µF
Parameter
Output voltage
Symbol
VO1
Conditions
Min
Typ Max
Unit
V
Tj = 25°C
6.7
7
7.3
Output voltage tolerance
VO2
VI = 9.5 V to 22 V, IO = 5 mA to 350 mA 6.65
Tj = 25°C
7.35
V
Line regulation 1
Line regulation 2
Load regulation 1
Load regulation 2
Bias current
REGIN1 VI = 9.5 V to 25 V, Tj = 25°C
REGIN2 VI = 10 V to 25 V, Tj = 25°C
REGL1 IO = 5 mA to 500 mA, Tj = 25°C
REGL2 IO = 5 mA to 200 mA, Tj = 25°C
57
6
100
50
mV
mV
mV
mV
mA
mA
mA
dB
2
20
10
4
140
70
IBias
Tj = 25°C
6
Bias current fluctuation to input ∆IBias(IN) VI = 10 V to 25 V, Tj = 25°C
Bias current fluctuation to load ∆IBias(L) IO = 5 mA to 350 mA, Tj = 25°C
0.8
0.5
Ripple rejection ratio
RR
VI = 10 V to 20 V, IO = 100 mA, f = 120 Hz
•
Design reference data
Note) The characteristics listed below are theoretical values based on the IC design and are not guaranteed.
Parameter
Output noise voltage
Symbol
Conditions
f = 10 Hz to 100 kHz
Min
Typ Max
Unit
µV
V
VNO
48
2
Minimum input/output voltage VDIF(min) IO = 500 mA, Tj = 25°C
difference
Output short-circuit current
Peak output current
IO(Short) VI = 35 V, Tj = 25°C
IO(Peak) Tj = 25°C
300
1000
− 0.5
mA
mA
Output voltage temperature
coefficient
∆VO / Ta IO = 5 mA, Tj = 0°C to 125°C
mV/°C
Thermal protection operating
temperature
Tj(TH) IO = 5 mA
150
°C
4
Voltage Regulators
AN78MxxNSP Series
I Electrical Characteristics at Ta = 25°C (continued)
•
AN78M08NSP (8 V type)
The specified condition Tj = 25°C means that the test should be carried out within so short a test time (within 10 ms)
that the characteristic value drift due to the chip junction temperature rise can be ignored.
Unless otherwise specified, VI = 14 V, IO = 350 mA, CI = 0.33 µF and CO = 0.1 µF
Parameter
Output voltage
Symbol
VO1
Conditions
Min
Typ Max
Unit
V
Tj = 25°C
7.7
8
8.3
8.4
Output voltage tolerance
VO2
VI = 10.5 V to 22 V, IO = 5 mA to 350 mA 7.6
Tj = 25°C
V
Line regulation 1
Line regulation 2
Load regulation 1
Load regulation 2
Bias current
REGIN1 VI = 10.5 V to 25 V, Tj = 25°C
REGIN2 VI = 11 V to 25 V, Tj = 25°C
REGL1 IO = 5 mA to 500 mA, Tj = 25°C
REGL2 IO = 5 mA to 200 mA, Tj = 25°C
6
2
100
50
mV
mV
mV
mV
mA
mA
mA
dB
25
10
4.1
160
80
IBias
Tj = 25°C
6
Bias current fluctuation to input ∆IBias(IN) VI = 10.5 V to 25 V, Tj = 25°C
Bias current fluctuation to load ∆IBias(L) IO = 5 mA to 350 mA, Tj = 25°C
0.8
0.5
Ripple rejection ratio
RR
VI = 11.5 V to 21.5 V, IO = 100 mA, f = 120 Hz 56
•
Design reference data
Note) The characteristics listed below are theoretical values based on the IC design and are not guaranteed.
Parameter
Output noise voltage
Symbol
Conditions
f = 10 Hz to 100 kHz
Min
Typ Max
Unit
µV
V
VNO
48
2
Minimum input/output voltage VDIF(min) IO = 500 mA, Tj = 25°C
difference
Output short-circuit current
Peak output current
IO(Short) VI = 35 V, Tj = 25°C
IO(Peak) Tj = 25°C
300
1000
− 0.5
mA
mA
Output voltage temperature
coefficient
∆VO / Ta IO = 5 mA, Tj = 0°C to 125°C
mV/°C
Thermal protection operating
temperature
Tj(TH) IO = 5 mA
150
°C
5
AN78MxxNSP Series
Voltage Regulators
I Electrical Characteristics at Ta = 25°C (continued)
•
AN78M09NSP (9 V type)
The specified condition Tj = 25°C means that the test should be carried out within so short a test time (within 10 ms)
that the characteristic value drift due to the chip junction temperature rise can be ignored.
Unless otherwise specified, VI = 15 V, IO = 350 mA, CI = 0.33 µF and CO = 0.1 µF
Parameter
Output voltage
Symbol
VO1
Conditions
Min
Typ Max
Unit
V
Tj = 25°C
8.65
9
9.35
9.45
Output voltage tolerance
VO2
VI = 11.5 V to 24 V, IO = 5 mA to 350 mA 8.55
Tj = 25°C
V
Line regulation 1
Line regulation 2
Load regulation 1
Load regulation 2
Bias current
REGIN1 VI = 11.5 V to 25 V, Tj = 25°C
REGIN2 VI = 12 V to 25 V, Tj = 25°C
REGL1 IO = 5 mA to 500 mA, Tj = 25°C
REGL2 IO = 5 mA to 200 mA, Tj = 25°C
56
7
2
100
50
mV
mV
mV
mV
mA
mA
mA
dB
25
10
4.1
180
90
IBias
Tj = 25°C
6
Bias current fluctuation to input ∆IBias(IN) VI = 12 V to 25 V, Tj = 25°C
Bias current fluctuation to load ∆IBias(L) IO = 5 mA to 350 mA, Tj = 25°C
0.8
0.5
Ripple rejection ratio
RR
VI = 12 V to 22 V, IO = 100 mA, f = 120 Hz
•
Design reference data
Note) The characteristics listed below are theoretical values based on the IC design and are not guaranteed.
Parameter
Output noise voltage
Symbol
Conditions
f = 10 Hz to 100 kHz
Min
Typ Max
Unit
µV
V
VNO
60
2
Minimum input/output voltage VDIF(min) IO = 500 mA, Tj = 25°C
difference
output short-circuit current
Peak output current
IO(Short) VI = 35 V, Tj = 25°C
IO(Peak) Tj = 25°C
300
1000
− 0.5
mA
mA
Output voltage temperature
coefficient
∆VO / Ta IO = 5 mA, Tj = 0°C to 125°C
mV/°C
Thermal protection operating
temperature
Tj(TH) IO = 5 mA
150
°C
6
Voltage Regulators
AN78MxxNSP Series
I Electrical Characteristics at Ta = 25°C (continued)
•
AN78M10NSP (10 V type)
The specified condition Tj = 25°C means that the test should be carried out within so short a test time (within 10 ms)
that the characteristic value drift due to the chip junction temperature rise can be ignored.
Unless otherwise specified, VI = 16 V, IO = 350 mA, CI = 0.33 µF and CO = 0.1 µF
Parameter
Output voltage
Symbol
VO1
Conditions
Min
Typ Max
Unit
V
Tj = 25°C
9.6
10
10.4
10.5
Output voltage tolerance
VO2
VI = 12.5 V to 25 V, IO = 5 mA to 350 mA 9.5
Tj = 25°C
V
Line regulation 1
Line regulation 2
Load regulation 1
Load regulation 2
Bias current
REGIN1 VI = 12.5 V to 30 V, Tj = 25°C
REGIN2 VI = 13 V to 25 V, Tj = 25°C
REGL1 IO = 5 mA to 500 mA, Tj = 25°C
REGL2 IO = 5 mA to 200 mA, Tj = 25°C
7
2
100
50
mV
mV
mV
mV
mA
mA
mA
dB
25
10
4.1
200
100
6
IBias
Tj = 25°C
Bias current fluctuation to input ∆IBias(IN) VI = 13 V to 25 V, Tj = 25°C
Bias current fluctuation to load ∆IBias(L) IO = 5 mA to 350 mA, Tj = 25°C
0.8
0.5
Ripple rejection ratio
RR
VI = 13 V to 23 V, IO = 100 mA, f = 120 Hz 56
•
Design reference data
Note) The characteristics listed below are theoretical values based on the IC design and are not guaranteed.
Parameter
Output noise voltage
Symbol
Conditions
f = 10 Hz to 100 kHz
Min
Typ Max
Unit
µV
V
VNO
65
2
Minimum input/output voltage VDIF(min) IO = 500 mA, Tj = 25°C
difference
Output short-circuit current
Peak output current
IO(Short) VI = 35 V, Tj = 25°C
IO(Peak) Tj = 25°C
300
1000
− 0.5
mA
mA
Output voltage temperature
coefficient
∆VO / Ta IO = 5 mA, Tj = 0°C to 125°C
mV/°C
Thermal protection operating
temperature
Tj(TH) IO = 5 mA
150
°C
7
AN78MxxNSP Series
Voltage Regulators
I Electrical Characteristics at Ta = 25°C (continued)
•
AN78M12NSP (12 V type)
The specified condition Tj = 25°C means that the test should be carried out within so short a test time (within 10 ms)
that the characteristic value drift due to the chip junction temperature rise can be ignored.
Unless otherwise specified, VI = 19 V, IO = 350 mA, CI = 0.33 µF and CO = 0.1 µF
Parameter
Output voltage
Symbol
VO1
Conditions
Min
Typ Max
Unit
V
Tj = 25°C
11.5
12
12.5
12.6
Output voltage tolerance
VO2
VI = 14.5 V to 27 V, IO = 5 mA to 350 mA 11.4
Tj = 25°C
V
Line regulation 1
Line regulation 2
Load regulation 1
Load regulation 2
Bias current
REGIN1 VI = 14.5 V to 30 V, Tj = 25°C
REGIN2 VI = 16 V to 30 V, Tj = 25°C
REGL1 IO = 5 mA to 500 mA, Tj = 25°C
REGL2 IO = 5 mA to 200 mA, Tj = 25°C
55
8
2
100
50
mV
mV
mV
mV
mA
mA
mA
dB
25
10
4.3
240
120
6
IBias
Tj = 25°C
Bias current fluctuation to input ∆IBias(IN) VI = 14.5 V to 30 V, Tj = 25°C
Bias current fluctuation to load ∆IBias(L) IO = 5 mA to 350 mA, Tj = 25°C
0.8
0.5
Ripple rejection ratio
RR
VI = 15 V to 25 V, IO = 100 mA, f = 120 Hz
•
Design reference data
Note) The characteristics listed below are theoretical values based on the IC design and are not guaranteed.
Parameter
Output noise voltage
Symbol
Conditions
f = 10 Hz to 100 kHz
Min
Typ Max
Unit
µV
V
VNO
75
2
Minimum input/output voltage VDIF(min) IO = 500 mA, Tj = 25°C
difference
Output short-circuit current
Peak output current
IO(Short) VI = 35 V, Tj = 25°C
IO(Peak) Tj = 25°C
300
1000
− 0.5
mA
mA
Output voltage temperature
coefficient
∆VO / Ta IO = 5 mA, Tj = 0°C to 125°C
mV/°C
Thermal protection operating
temperature
Tj(TH) IO = 5 mA
150
°C
8
Voltage Regulators
AN78MxxNSP Series
I Electrical Characteristics at Ta = 25°C (continued)
•
AN78M15NSP (15 V type)
The specified condition Tj = 25°C means that the test should be carried out within so short a test time (within 10 ms)
that the characteristic value drift due to the chip junction temperature rise can be ignored.
Unless otherwise specified, VI = 23 V, IO = 350 mA, CI = 0.33 µF and CO = 0.1 µF
Parameter
Output voltage
Symbol
VO1
Conditions
Min
Typ Max
Unit
V
Tj = 25°C
14.4
15
15.6
Output voltage tolerance
VO2
VI = 17.5 V to 30 V, IO = 5 mA to 350 mA 14.25
Tj = 25°C
15.75
V
Line regulation 1
Line regulation 2
Load regulation 1
Load regulation 2
Bias current
REGIN1 VI = 17.5 V to 30 V, Tj = 25°C
REGIN2 VI = 20 V to 30 V, Tj = 25°C
REGL1 IO = 5 mA to 500 mA, Tj = 25°C
REGL2 IO = 5 mA to 200 mA, Tj = 25°C
10
3
100
50
mV
mV
mV
mV
mA
mA
mA
dB
25
10
4.3
300
150
6
IBias
Tj = 25°C
Bias current fluctuation to input ∆IBias(IN) VI = 17.5 V to 30 V, Tj = 25°C
Bias current fluctuation to load ∆IBias(L) IO = 5 mA to 350 mA, Tj = 25°C
0.8
0.5
Ripple rejection ratio
RR
VI = 18.5 V to 28.5 V, IO = 100 mA, f =120 Hz 54
•
Design reference data
Note) The characteristics listed below are theoretical values based on the IC design and are not guaranteed.
Parameter
Output noise voltage
Symbol
Conditions
f = 10 Hz to 100 kHz
Min
Typ Max
Unit
µV
V
VNO
90
2
Minimum input/output voltage VDIF(min) IO = 500 mA, Tj = 25°C
difference
Output short-circuit current
Peak output current
IO(Short) VI = 35 V, Tj = 25°C
IO(Peak) Tj = 25°C
300
1000
− 0.5
mA
mA
Output voltage temperature
coefficient
∆VO / Ta IO = 5 mA, Tj = 0°C to 125°C
mV/°C
Thermal protection operating
temperature
Tj(TH) IO = 5 mA
150
°C
9
AN78MxxNSP Series
Voltage Regulators
I Electrical Characteristics at Ta = 25°C (continued)
•
AN78M18NSP (18 V type)
The specified condition Tj = 25°C means that the test should be carried out within so short a test time (within 10 ms)
that the characteristic value drift due to the chip junction temperature rise can be ignored.
Unless otherwise specified, VI = 27 V, IO = 350 mA, CI = 0.33 µF and CO = 0.1 µF
Parameter
Output voltage
Symbol
VO1
Conditions
Min
17.3
17.1
Typ Max
Unit
V
Tj = 25°C
18
18.7
18.9
Output voltage tolerance
VO2
VI = 21 V to 33 V, IO = 5 mA to 350 mA
Tj = 25°C
V
Line regulation 1
Line regulation 2
Load regulation 1
Load regulation 2
Bias current
REGIN1 VI = 21 V to 33 V, Tj = 25°C
REGIN2 VI = 22 V to 33 V, Tj = 25°C
REGL1 IO = 5 mA to 500 mA, Tj = 25°C
REGL2 IO = 5 mA to 200 mA, Tj = 25°C
53
10
5
100
50
mV
mV
mV
mV
mA
mA
mA
dB
30
10
4.4
360
180
6
IBias
Tj = 25°C
Bias current fluctuation to input ∆IBias(IN) VI = 21 V to 33 V, Tj = 25°C
Bias current fluctuation to load ∆IBias(L) IO = 5 mA to 350 mA, Tj = 25°C
0.8
0.5
Ripple rejection ratio
RR
VI = 22 V to 32 V, IO = 100 mA, f = 120 Hz
•
Design reference data
Note) The characteristics listed below are theoretical values based on the IC design and are not guaranteed.
Parameter
Output noise voltage
Symbol
Conditions
f = 10 Hz to 100 kHz
Min
Typ Max
Unit
µV
V
VNO
100
2
Minimum input/output voltage VDIF(min) IO = 500 mA, Tj = 25°C
difference
Output short-circuit current
Peak output current
IO(Short) VI = 35 V, Tj = 25°C
IO(Peak) Tj = 25°C
300
1000
− 0.5
mA
mA
Output voltage temperature
coefficient
∆VO / Ta IO = 5 mA, Tj = 0°C to 125°C
mV/°C
Thermal protection operating
temperature
Tj(TH) IO = 5 mA
150
°C
10
Voltage Regulators
AN78MxxNSP Series
I Application Notes
1. PD Ta curves of SP-3SU
PD ¾ Ta
6.00
5.00
4.00
3.00
2.00
Mounted on Al board�
(50 × 50 × t2.0 mm3)
Rth(j-a) = 25.0°C/W
Mounted on
glass epoxy board 2
(50 × 50 × t1.5 mm3)
Rth(j-a) = 89.3°C/W
Mounted on
glass epoxy board 1
(20 × 20 × t1.7 mm3)
Rth(j-a) = 147.0°C/W
1.40
1.00
0.85
0.70
Independent IC
without a heat sink
Rth( j-a) = 178.0°C/W
0
0
25
50
75
100
125
)
150
(°
Ambient temperature Ta
C
2. Main Characteristics
Output voltage temperature characteristic
Minimum input/output voltage difference vs.
load current characteristic
2
VIN = 10 V
Tj = 25°C
1.8
0
IO = 5 mA
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
− 0.5
−1
−1.5
−100
−50 −25
0
25
50
75
100 125 150
0
0.1
0.2
0.3
0.4
0.5
Ta (°C)
IO (A)
Current limit characteristics
Ripple rejection ratio vs. frequency characteristic
6
5
4
3
2
1
0
0
VIN = 10 V
Tj = 25°C
IO = 100 mA
−10
−20
−30
−40
−50
−60
−70
−80
VI = 30 V
VI = 20 V
VI = 10 V
0
0.2
0.4
0.6
0.8
1.0
1.2
100
1k
10k
100k
1M
IO (A)
Frequency f (Hz)
11
相关型号：
©2020 ICPDF网 联系我们和版权申明