ATH10KR8 [ETC]
High Stability Miniature Thermistor; 高稳定性微型热敏电阻
| 型号： | ATH10KR8 |
| 厂家： | 
ETC |
| 描述： | High Stability Miniature Thermistor |
| 文件： | 总2页 (文件大小：301K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
High Stability Miniature Thermistor
ATH10KR8
Analog Technologies
SPECIFICATIONS
Nominal Resistance @ 25°C: 10K ± 1%
B Value @ 25°C /85°C:
B Value @ 0°C /100°C:
B Value @ 25°C /100°C:
Thermistor Diameter:
Thermistor Length:
Lead Diameter:
3480K ± 1%
3450K ± 1%
3497K ± 1%
0.8 ± 0.1mm
1.4 ± 0.4mm
0.15mm
Lead Length:
Dissipation Factor:
Heat Capacity:
63 ± 3mm
0.4mW/K
1.3mJ/K
Maximum Power @ 25°C:
18mW
APPLICATION
Drill a hole on the object for which the temperature needs to
be measured and use thermally conductive epoxy to pot the
thermistor inside the hole. The hole diameter should be
between 1.2 to 1.4mm and the depth should between 2 to
2.5mm. When a deeper hole is needed, drill a 2 stage hole to
prevent mounting epoxy bobbles trapped inside which would
cause temperature measurement errors. Figure 2 shows the
section view of the 2 stage hole.
MAIN FEATURES
Glass Encapsulated for Long Term Stability & Reliability
High Stability: <0.1°C/Y
Small Size: φ0.8mm×1.4mm
High Resistance Accuracy: 1%
Quick Response Time: 3s
Thermal Conductive Epoxy
3 – 5 mm
Wide Temp. Range: −55°C to 250°C
2 – 2.5 mm
APPLICATIONS
Temperature sensing for laser diodes, optical components, etc.
1.2 – 1.5 mm
DESCRIPTION
The ATH10KR8 is a high precision glass encapsulated
thermistor. Comparing with conventional epoxy encapsulated
thermistors, ATH10KR8 presents higher long term stability
and wider temperature range. In addition, it has a small size
and short response time.
Figure 2 Section View of the 2 Stage Hole
The worst mounting result is that there are air bubbles
trapped inside the thermistor mounting hole. These bubbles
cause thermal sensing time delay and sensing temperature
errors. To avoid the bubbles, use thin epoxy, vibrate the
assembly before curing, and cure the epoxy inside the
mounting hole at high temperature, 80°C to 150°C,
depending on the epoxy used and the maximum temperature
assembly components allow.
The ATH10KR8 can be used to measure the temperatures for
laser diodes, optical components, etc., with high accuracy and
long term stability.
φ0.8
The thermistor lead wires are made of plain copper and there
is no insulation coating on them, please make sure that they
do not touch each other after mounting the thermistor.
φ1.4
Some thermal conductive epoxies are also electrically
conductive and such epoxies should not be used for mounting
the thermistors, since the lead wires are conductive.
63
ORDERING INFORMATION
φ0.15
Bare copper wire
Part number: ATH10KR8
Quantity
Price
1 - 9
$6.4
10 - 49
$5.2
50 - 249
$3.8
≥250
$2.4
Figure 1 Side View of ATH10KR8
550 E. Weddell Drive, Suite 4, Sunnyvale, CA 94089, U. S. A. Tel.: (408) 747-9760, Fax: (408) 747-9770, Web: w w w .analogtechnologies.com
© Copyrights 2000 – 2005, Analog Technologies, Inc. All Rights Reserved.
1
High Stability Miniature Thermistor
ATH10KR8
Analog Technologies
Resistance Temperature Characteristics
NOTICE
1. ATI warrants performance of its products for one year to the specifications applicable at the time of sale, except for those being damaged by excessive
abuse. Products found not meeting the specifications within one year from the date of sale can be exchanged free of charge.
2. ATI reserves the right to make changes to its products or to discontinue any product or service without notice, and advise customers to obtain the latest
version of relevant information to verify, before placing orders, that information being relied on is current and complete.
3. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty,
patent infringement, and limitation of liability. Testing and other quality control techniques are utilized to the extent ATI deems necessary to support this
warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements.
4. Customers are responsible for their applications using ATI components. In order to minimize risks associated with the customers’ applications, adequate
design and operating safeguards must be provided by the customers to minimize inherent or procedural hazards. ATI assumes no liability for applications
assistance or customer product design.
5. ATI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of ATI covering or relating to any combination, machine, or process in which such products or services might be or are used.
ATI’s publication of information regarding any third party’s products or services does not constitute ATI’s approval, warranty or endorsement thereof.
6. IP (Intellectual Property) Ownership: ATI retains the ownership of full rights for special technologies and/or techniques embedded in its products, the
designs for mechanics, optics, plus all modifications, improvements, and inventions made by ATI for its products and/or projects.
550 E. Weddell Drive, Suite 4, Sunnyvale, CA 94089, U. S. A. Tel.: (408) 747-9760, Fax: (408) 747-9770, Web: w w w .analogtechnologies.com
© Copyrights 2000 – 2005, Analog Technologies, Inc. All Rights Reserved.
2
相关型号：
©2020 ICPDF网 联系我们和版权申明