B07-201-M3KG [ETC]
"FILTER REGULATOR G1/4""" ; “过滤减压阀G1 / 4 ” “ ”型号: | B07-201-M3KG |
厂家: | ETC |
描述: | "FILTER REGULATOR G1/4"""
|
文件: | 总4页 (文件大小:80K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
B07
Miniature Series 07
General Purpose Filter/Regulator
1/8" and 1/4" Port Sizes
● Compact design
● Full flow gauge ports
● Low torque, non-rising adjusting knob
● Snap action knob locks pressure setting when
pushed in
● Standard relieving models allow reduction of outlet
pressure even when the system is dead-ended
● Protects air operated devices by removing liquid and
solids contaminants
● Screw-on bowl reduces maintenance time
● Can be disassembled without the use of tools or
removal from the air line
Technical Data
Fluid: Compressed air
Maximum pressure:
Transparent bowl: 10 bar (145 psig)
Metal bowl: 17 bar (250 psig)
Operating temperature:*
Ordering Information
See Ordering Information on the following
pages.
Transparent bowl: -20° to +50°C (0° to +125°F)
Metal bowl: -20° to +65°C (0° to +150°F)
* Air supply must be dry enough to avoid ice formation at temperatures below +2°C (+35°F)
Particle removal: 5 µm or 40 µm filter element
Air quality: Within ISO 8573-1, Class 3 and Class 5 (particulates)
Typical flow at 10 bar (100 psig) inlet pressure, 6,3 bar (90 psig) set
pressure and a droop of 1 bar (15 psig) from set:
1/8" Ports: 6 dm3/s (13 scfm) with 5 µm element
1/4" Ports: 6 dm3/s (13 scfm) with 5 µm element
Nominal bowl size: 31 ml (1 oz)
Gauge ports:
ISO Symbols
1/8" PTF with PTF main ports
1/8" ISO Rc with ISO Rc main ports
1/8" ISO Rc with ISO G main ports
Drain connection: 1/8" pipe
Automatic Drain
Relieving
Manual Drain
Relieving
Automatic drain operation: Spitter type drain operates momentarily
when a rapid change in air flow occurs or when the supply
pressure is reduced.
Materials:
Body: Zinc
Bonnet: Acetal
Automatic Drain
Non-relieving
Manual Drain
Non-relieving
Valve: Brass/nitrile
Valve seat: Acetal
Bowl:
Transparent: Polycarbonate
Metal: Zinc
Element: Sintered polypropylene
Elastomers: Nitrile
Our policy is one of continuous research and development.
We reserve the right to amend, without notice, the specifications given in this document.
1/97
N/AL.8.300.300.01
B07
Typical Performance Characteristics
PORT SIZE: 1/4"
RANGE: 0,3 to 7 bar (5 to 100 psi)
ELEMENT: 40 µm
FLOW CHARACTERISTICS
INLET PRESSURE: 10 bar g (145 psig)
8
6
4
2
0
100
80
60
40
20
0
0
0
2
4
6
8
10
dm3/s
4
8
12
AIR FLOW
16
20
24 scfm
Ordering Information. Models listed include ISO G threads, transparent bowl, relieving diaphragm, automatic drain, 40 µm
element, 0,3 to 7 bar (5 to 100 psig) outlet pressure adjustment range* .
Port Size
G1/8
G1/4
Model Number
B07-101-A3KG
B07-201-A3KG
Flow† dm3/s (scfm)
6,2 dm3/s (13)
6,5 dm3/s (14)
Weight kg (lbs)
0,26 (0.57)
0,26 (0.57)
† Typical flow with 7 bar (100 psig) inlet pressure, 6,3 bar (90 psig) set pressure and a 1 bar (14.5 psig) droop from set.
Alternative Models
★ ★ ★ ★ ★ ★ ★
B 0 7
-
-
Threads
PTF
ISO Rc taper
ISO G parallel
Substitute
Port Size
1/8"
1/4"
Substitute
A
B
G
1
2
Bowl
Relief Type
Relieving
Non-relieving
Relieving
Non-relieving
Relieving
Non-relieving
Gauge
Substitute
01
Transparent
Transparent
Metal
Metal
Metal
Without
Without
Without
Without
Without
Without
Outlet Pressure Adjustment Ranges*
0.1 to 0.7 bar (1 to 10 psig)
0.3 to 3.5 bar (5 to 50 psig)
0.3 to 7 bar (5 to 100 psig)
0.3 to 10 bar (5 to 145 psig)
Substitute
03
33
35
05**
07**
A
E
K
M**
Metal
Element
5 µm
40 µm
Substitute
* Outlet pressure can be adjusted to pressures in excess of,
and less than, those specified. Do not use these units to
control pressures outside of the specified ranges.
1
3
** When specifying 10 bar (145 psig) unit, eg. B07-205-A3MG,
also note correct code at 5th and 6th digits.
Drain
Automatic
Manual
Substitute
A
M
Accessories
Wall Mounting Bracket and
Panel Nut for P1H Unit
Tamper Resistant
Field Modification
Ø 40 mm
Pressure Gauge
Panel Nut
R1/8 Connection 1/8"PTF Connection
Plastic: 18-025-003
Plastic: 2962-89
Metal: 2962-04
Knob and screw: 18-001-092
Screw only: 6097-08
2 bar (30 psig):
4 bar (60 psig):
10 bar (150 psig):
25 bar (350 psig):
—
18-013-214
18-013-211
18-013-212
—
18-013-990
18-013-989
18-013-908
Our policy is one of continuous research and development.
We reserve the right to amend, without notice, the specifications given in this document.
N/AL.8.300.300.02
1/97
B07
Dimensions mm (inches)
41 (1.63)
Panel mounting hole diameter 30 mm (1.19")
Panel thickness 0 to 6 mm (0 to 0.25")
38 (1.50)
28 (1.1)
28 (1.1)
Automatic Drain
Manual Drain
*
Minimum clearance to remove bowl
Bracket Mounting
Bracket Kit Reference
Use 3mm (1/8") screws to mount bracket to wall.
Item
All models
Part Number
18-025-003
38 (1.50)
24
(0.93)
7 (0.29)
Service Kits
Item
Type
Relieving models, 40 µm element
Non-relieving models, 40 µm element 3820-13
Part number
3820-14
Service kit
Manual
Automatic
773-03
3654-02
Replacement drains
Service kit includes slip ring, diaphragm, valve seat with o-ring, valve,
valve spring, element, element gasket, and bowl o-ring.
Our policy is one of continuous research and development.
We reserve the right to amend, without notice, the specifications given in this document.
1/97
N/AL.8.300.300.03
B07
Warning
These products are intended for use in industrial compressed air
systems only. Do not use these products where pressures and temperatures
can exceed those listed under ‘Technical Data’.
Before using these products with fluids other than those specified, for
non-industrial applications, life-support systems, or other applications not
within published specifications, consult NORGREN.
Through misuse, age, or malfunction, components used in fluid power
systems can fail in various modes. The system designer is warned to
consider the failure modes of all component parts used in fluid power
systems and to provide adequate safeguards to prevent personal injury or
damage to equipment in the event of such failure.
System designers must provide a warning to end users in the
system instructional manual if protection against a failure mode
cannot be adequately provided.
System designers and end users are cautioned to review specific
warnings found in instruction sheets packed and shipped with these
products.
Water vapor will pass through these units and will condense into liquid
if air temperature drops in the downstream system. Install an air dryer if
water condensation could have a detrimental effect on the application.
Our policy is one of continuous research and development.
We reserve the right to amend, without notice, the specifications given in this document.
N/AL.8.300.300.04
1/97
相关型号:
©2020 ICPDF网 联系我们和版权申明